mirror of
https://github.com/darlinghq/darling-gdb.git
synced 2024-12-13 06:56:05 +00:00
2081365ffa
these routines much smarter about updating registers from the target, only doing so when absolutely necessary. This really speeds up register modification on some remote targets. * monitor.c: More cleanups. Get rid of monitor_load_ascii_srec. BFD makes this unnecessary. Lots of debugging speedups. * (expect): NULL terminate return string. * (monitor_open monitor_supply_register parse_register_dump monitor_wait monitor_fetch_register): Switch to using GNU regexp library to parse multi-register displays. * (monitor_read_memory): Read multiple bytes (up to 16) at once. * (monitor_create_inferior): Call clear_proceed_status to make run command notice first breakpoint. * (monitor_load): Clean up. Reset inferior_pid, set pc to start address and reset symbol table stuff to make loads put things into a fresh state. * (monitor_load_srec): Lower sleep time to 1 second. * monitor.h (struct monitor_ops): Add register_pattern and supply_register to monitor_ops. * rom68k-rom.c: Add new support for handling register dumps.
144 lines
6.3 KiB
C
144 lines
6.3 KiB
C
/* Remote debugging interface ROM monitors.
|
|
* Copyright 1990, 1991, 1992 Free Software Foundation, Inc.
|
|
* Contributed by Cygnus Support. Written by Rob Savoye for Cygnus.
|
|
*
|
|
* Copyright 1990, 1991, 1992 Free Software Foundation, Inc.
|
|
* Contributed by Cygnus Support. Written by Rob Savoye for Cygnus.
|
|
*
|
|
* This file is part of GDB.
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation; either version 2 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software
|
|
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
|
|
*/
|
|
|
|
struct rom_cmd_data {
|
|
char *cmd; /* command to send */
|
|
char *delim; /* the delimiter */
|
|
char *result; /* the result */
|
|
};
|
|
|
|
/* This structure describes the strings necessary to give small command
|
|
sequences to the monitor, and parse the response.
|
|
|
|
CMD is the actual command typed at the monitor. Usually this has embedded
|
|
sequences ala printf, which are substituted with the arguments appropriate
|
|
to that type of command. Ie: to examine a register, we substitute the
|
|
register name for the first arg. To modify memory, we substitute the memory
|
|
location and the new contents for the first and second args, etc...
|
|
|
|
RESP_DELIM used to home in on the response string, and is used to
|
|
disambiguate the answer within the pile of text returned by the monitor.
|
|
This should be a unique string that immediately precedes the answer. Ie: if
|
|
your monitor prints out `PC: 00000001= ' in response to asking for the PC,
|
|
you should use `: ' as the RESP_DELIM. RESP_DELIM may be NULL if the res-
|
|
ponse is going to be ignored, or has no particular leading text.
|
|
|
|
TERM is the string that the monitor outputs to indicate that it is idle, and
|
|
waiting for input. This is usually a prompt of some sort. In the previous
|
|
example, it would be `= '. It is important that TERM really means that the
|
|
monitor is idle, otherwise GDB may try to type at it when it isn't ready for
|
|
input. This is a problem because many monitors cannot deal with type-ahead.
|
|
TERM may be NULL if the normal prompt is output.
|
|
|
|
TERM_CMD is used to quit out of the subcommand mode and get back to the main
|
|
prompt. TERM_CMD may be NULL if it isn't necessary. It will also be
|
|
ignored if TERM is NULL.
|
|
*/
|
|
|
|
struct cmd_resp {
|
|
char *cmd; /* Command to send */
|
|
char *resp_delim; /* String just prior to the desired value */
|
|
char *term; /* Terminating string to search for */
|
|
char *term_cmd; /* String to get out of sub-mode (if necessary) */
|
|
};
|
|
|
|
struct monitor_ops {
|
|
int type; /* 1 is ascii, 0 is GDB remote protocol */
|
|
char *init; /* initialize to the monitor */
|
|
char *execute; /* execute or usually GO command */
|
|
char *resume; /* continue command */
|
|
char *step; /* single step */
|
|
char *set_break; /* set a breakpoint */
|
|
char *clr_break; /* clear a breakpoint */
|
|
int clr_type; /* number or address for clearing */
|
|
struct cmd_resp setmem; /* set memory to a value */
|
|
struct cmd_resp getmem; /* display memory */
|
|
struct cmd_resp setreg; /* set a register */
|
|
struct cmd_resp getreg; /* get a register */
|
|
/* Some commands can dump a bunch of registers
|
|
at once. This comes as a set of REG=VAL
|
|
pairs. This should be called for each pair
|
|
of registers that we can parse to supply
|
|
GDB with the value of a register. */
|
|
char *register_pattern; /* Pattern that picks out register from reg dump */
|
|
void (*supply_register) PARAMS ((char *name, int namelen, char *val, int vallen));
|
|
char *load; /* load command */
|
|
char *prompt; /* monitor command prompt */
|
|
char *cmd_delim; /* end-of-command delimitor */
|
|
char *cmd_end; /* optional command terminator */
|
|
struct target_ops *target; /* target operations */
|
|
char **loadtypes; /* the load types that are supported */
|
|
char **loadprotos; /* the load protocols that are supported */
|
|
char *baudrates; /* supported baud rates */
|
|
int stopbits; /* number of stop bits */
|
|
char **regnames; /* array of register names in ascii */
|
|
};
|
|
|
|
extern struct monitor_ops *current_monitor;
|
|
|
|
#define PROTO_TYPE (current_monitor->type)
|
|
#define LOADTYPES (current_monitor->loadtypes)
|
|
#define LOADPROTOS (current_monitor->loadprotos)
|
|
#define INIT_CMD (current_monitor->init)
|
|
#define GO_CMD (current_monitor->execute)
|
|
#define CONT_CMD (current_monitor->resume)
|
|
#define STEP_CMD (current_monitor->step)
|
|
#define SET_BREAK_CMD (current_monitor->set_break)
|
|
#define CLR_BREAK_CMD (current_monitor->clr_break)
|
|
#define CLR_BREAK_ADDR (current_monitor->clr_type)
|
|
#define SET_MEM (current_monitor->setmem)
|
|
#define GET_MEM (current_monitor->getmem)
|
|
#define LOAD_CMD (current_monitor->load)
|
|
#define GET_REG (current_monitor->regget)
|
|
#define SET_REG (current_monitor->regset)
|
|
#define CMD_END (current_monitor->cmd_end)
|
|
#define CMD_DELIM (current_monitor->cmd_delim)
|
|
#define PROMPT (current_monitor->prompt)
|
|
#define TARGET_OPS (current_monitor->target)
|
|
#define TARGET_NAME (current_monitor->target->to_shortname)
|
|
#define BAUDRATES (current_monitor->baudrates)
|
|
#define STOPBITS (current_monitor->stopbits)
|
|
#define REGNAMES(x) (current_monitor->regnames[x])
|
|
#define ROMCMD(x) (x.cmd)
|
|
#define ROMDELIM(x) (x.delim)
|
|
#define ROMRES(x) (x.result)
|
|
|
|
#define push_monitor(x) current_monitor = x;
|
|
|
|
#define SREC_SIZE 160
|
|
#define GDBPROTO ((current_monitor->type) ? 0: 1)
|
|
|
|
/*
|
|
* FIXME: These are to temporarily maintain compatability with the
|
|
* old monitor structure till remote-mon.c is fixed to work
|
|
* like the *-rom.c files.
|
|
*/
|
|
#define MEM_PROMPT (current_monitor->loadtypes)
|
|
#define MEM_SET_CMD (current_monitor->setmem)
|
|
#define MEM_DIS_CMD (current_monitor->getmem)
|
|
#define REG_DELIM (current_monitor->regset.delim)
|
|
|
|
extern void monitor_open PARAMS ((char *args, struct monitor_ops *ops, int from_tty));
|
|
extern char *monitor_supply_register PARAMS ((int regno, char *valstr));
|