mirror of
https://github.com/hacks-guide/Guide_3DS.git
synced 2024-11-24 18:09:45 +00:00
61 lines
3.0 KiB
Plaintext
61 lines
3.0 KiB
Plaintext
---
|
|
title: "Installing boot9strap (2xrsa)"
|
|
---
|
|
|
|
#### Det du trenger
|
|
|
|
* The latest release of [SafeB9SInstaller](https://github.com/d0k3/SafeB9SInstaller/releases/latest)
|
|
* The latest release of [boot9strap](https://github.com/SciresM/boot9strap/releases/latest) *(standard boot9strap; not the `devkit` file, not the `ntr` file)*
|
|
* Siste utgave av [Luma3DS](https://github.com/AuroraWright/Luma3DS/releases/latest) *(`.7z`-filen)*
|
|
* Homebrew [Starter Kit](http://smealum.github.io/ninjhax2/starter.zip)
|
|
|
|
#### Instruksjoner
|
|
|
|
##### Seksjon I - Forarbeid
|
|
|
|
1. Slå av enheten
|
|
1. Sett inn SD-kortet i datamaskinen din
|
|
1. Copy `boot.firm` from the Luma3DS `.7z` to the root of your SD card
|
|
1. Copy _the contents of_ `starter.zip` to the root of your SD card
|
|
1. Create a folder named `boot9strap` on the root of your SD card
|
|
1. Copy `boot9strap.firm` and `boot9strap.firm.sha` from the boot9strap `.zip` to the `/boot9strap/` folder on your SD card
|
|
1. Copy `arm9.bin` and `arm11.bin` from the SafeB9SInstaller `.zip` to the root of your SD card
|
|
|
|
|
|
{: .notice--info}
|
|
|
|
1. Sett inn SD-kortet i konsollen igjen
|
|
1. Power on your device
|
|
|
|
##### Section II - Launching SafeB9SInstaller
|
|
|
|
1. Launch the browser and go to the following URL on your device
|
|
+ `http://2xrsa.3ds.guide`
|
|
+ If you are on a New 3DS, New 2DS, or Old 2DS and Wireless Communication is off, you can re-enable the wireless by removing the battery and unplugging the charger for several seconds then booting back up
|
|
+ Hvis du får feilmeldingen "This service is not available in your region", bruk systeminnstillingene for å sette enhetens land til å matche NAND regionen du installerte med 2.1.0 CTRTransfer
|
|
+ If you forgot to disable parental controls before CTRTransfering or otherwise cannot access wireless settings, note that the device will autoconnect to any network named `attwifi` with no password
|
|
+ Hvis du får en feilmelding, [Følg denne feilsøkingsveiledningen](troubleshooting#ts_browser)
|
|
1. If the exploit was successful, you will have booted into SafeB9SInstaller
|
|
|
|
##### Section III - Installing boot9strap
|
|
|
|
1. Wait for all safety checks to complete
|
|
1. When prompted, input the key combo given to install boot9strap
|
|
1. Once it has completed, press (A) to reboot your device
|
|
|
|
##### Section IV - Configuring Luma3DS
|
|
|
|
1. Your device should have rebooted into the Luma3DS configuration menu
|
|
+ If you get a black screen, [follow this troubleshooting guide](troubleshooting#ts_sys_b9s)
|
|
1. Use the (A) button and the D-Pad to turn on the following:
|
|
+ **"Show NAND or user string in System Settings"**
|
|
1. Trykk (Start) for å lagre og starte på nytt
|
|
+ If you get an error, just continue the next page
|
|
|
|
___
|
|
|
|
Note that *New 3DS* users who ended up on 2.1.0 after a CTRTransfer *must* [restore their NAND backup](godmode9-usage#nand_restore) before going to the [Finalizing Setup](finalizing-setup) page.
|
|
{: .notice--danger}
|
|
|
|
Continue to [Finalizing Setup](finalizing-setup)
|
|
{: .notice--primary} |