mirror of
https://github.com/joel16/android_device_sony_kitakami-common.git
synced 2024-11-23 11:49:47 +00:00
147 lines
4.4 KiB
Plaintext
147 lines
4.4 KiB
Plaintext
#######################################################################################
|
|
# Common configurations (applies to both V4L2 & non-V4L2)
|
|
#######################################################################################
|
|
|
|
# UART device port where Bluetooth controller is attached (default ttyS1)
|
|
#UartPort = /dev/ttyHS0
|
|
|
|
UartPort = /dev/brcm_bt_drv
|
|
UimUartPort = /dev/ttyHS0
|
|
|
|
# Target Baudrate to change to if different from 3000000
|
|
# This entry is mandatory if using V4L2
|
|
UartBaudRate = 3000000
|
|
|
|
# Firmware patch file location (compile default /vendor/firmware)
|
|
FwPatchFilePath = /system/etc/firmware
|
|
|
|
# uncomment if you want to load a specific version
|
|
FwPatchFileName = BCM43xx.hcd
|
|
|
|
# Firmware patch setttlement delay in millisec
|
|
# This entry is mandatory if using V4L2
|
|
FwPatchSettlementDelay = 100
|
|
|
|
# host/bt wake polarity to match with kernel settings
|
|
# 0: active low (negative logic)
|
|
# 1: active high (positive logic) (default)
|
|
LpmWakePolarity = 1
|
|
|
|
# stack/controller idle timeout in units (300/25ms)
|
|
# make sur controller supports 25ms
|
|
#LpmIdleTimeout = 2
|
|
|
|
#**************************************
|
|
# SCO I2S/PCM interface
|
|
# 0: PCM
|
|
# 1: I2S
|
|
#**************************************
|
|
#ScoInterface = 0
|
|
|
|
#**************************************
|
|
# SCO over PCM
|
|
#
|
|
# Configuration for SCO over PCM interface, which parameters are represented by array.
|
|
# Each PCM parameters' definations are listed as below, in order. Be NOTICED that
|
|
# this setting is ONLY VALID as PCM interface is selected/used.
|
|
#
|
|
# PCM Frame Type (SCO_PCM_IF_FRAME_TYPE)
|
|
# - 0: Short
|
|
# - 1: Long
|
|
#
|
|
# PCM Sync Mode (SCO_PCM_IF_SYNC_MODE)
|
|
# - 0: Slave
|
|
# - 1: Master
|
|
#
|
|
# PCM Clock Mode (SCO_PCM_IF_CLOCK_MODE)
|
|
# - 0: Slave
|
|
# - 1: Master
|
|
#
|
|
# PCM NBS(Narrow Band Speech) Clock Rate (SCO_PCM_IF_CLOCK_RATE)
|
|
# - 0: 128K
|
|
# - 1: 256K
|
|
# - 2: 512K
|
|
# - 3: 1024K
|
|
# - 4: 2048K
|
|
#
|
|
# PCM WBS(Wide Band Speech) Clock Rate (SCO_I2SPCM_IF_CLOCK_RATE4WBS)
|
|
# - 0: 128K
|
|
# - 1: 256K
|
|
# - 2: 512K
|
|
# - 3: 1024K
|
|
# - 4: 2048K
|
|
#
|
|
# PCM WBS (Wide Band Speech) Sample Rate (SCO_I2SPCM_IF_SAMPLE_RATE)
|
|
#
|
|
# - 0: 8K
|
|
# - 1: 16K
|
|
# - 2: 4K
|
|
#
|
|
# Carriers do not support 16K voice samples at present,
|
|
# so, setting PCM WBS Sample Rate to 8K (0) for now.
|
|
#
|
|
#**************************************
|
|
#ScoPCMifParams = {0,0,0,4,4,0}
|
|
|
|
#**************************************
|
|
# PCM Format
|
|
#
|
|
# Configuration for PCM format, which parameters are represented by array.
|
|
# Each PCM format parameters' definations/descriptions are listed as below, in order.
|
|
#
|
|
# Shift Mode (PCM_DATA_FMT_SHIFT_MODE)
|
|
# - 0: MSB first
|
|
# - 1: LSB first
|
|
#
|
|
# Fill Bits (PCM_DATA_FMT_FILL_BITS)
|
|
# - Specifies the value with which to fill unused bits
|
|
# if Fill_Method is set to programmable
|
|
#
|
|
# Fill Method (PCM_DATA_FMT_FILL_METHOD)
|
|
# - 0 : 0's
|
|
# - 1 : 1's
|
|
# - 2 : Signed
|
|
# - 3 : Programmable
|
|
#
|
|
# Fill Num (PCM_DATA_FMT_FILL_NUM)
|
|
# - Specifies the number of bits to be filled
|
|
#
|
|
# Justify Mode (PCM_DATA_FMT_JUSTIFY_MODE)
|
|
# - 0: Left justify (fill data shifted out last)
|
|
# - 1: Right justify (fill data shifted out first)
|
|
#
|
|
#**************************************
|
|
#ScoPCMFmtParams = {0,0,3,0,0}
|
|
|
|
#######################################################################################
|
|
|
|
#######################################################################################
|
|
# Configurations specific to V4L2 based solution
|
|
#######################################################################################
|
|
|
|
# Setting this to true enables Low Power Mode (LPM) in the shared
|
|
# line discipline driver. Set this to fale if the LPM is not
|
|
# enabled or if it is handled in the platform
|
|
LpmEnable=true
|
|
|
|
#For hammerhead and grouper LPM is through bluesleep
|
|
#LPM for maguro and manta is done by UART driver itself
|
|
LpmUseBluesleep=false
|
|
|
|
#Set to true if bd address was programmed into firmware using OTP
|
|
UseControllerBdaddr=false
|
|
|
|
#Enable debugging (add values below to enable multiple options)
|
|
# enable logging in driver for init/release driver : 1
|
|
# enable logging in driver for open : 2
|
|
# enable logging in driver for close : 4
|
|
# enable logging in driver for Tx : 8
|
|
# enable logging in driver for Rx : 16
|
|
DBG_BT_DRV = 31
|
|
DBG_LDISC_DRV = 31
|
|
DBG_FM_DRV = 31
|
|
#***************************************************************************
|
|
|
|
#######################################################################################
|
|
|