mirror of
https://github.com/libretro/retroarch-joypad-autoconfig.git
synced 2024-12-02 13:16:20 +00:00
95 lines
2.5 KiB
INI
95 lines
2.5 KiB
INI
# 3H Dual Arcade USB Adapter
|
|
#
|
|
# This is an adapter board that converts arcade cabinet inputs to behave like
|
|
# two USB gamepads.
|
|
#
|
|
# Special Notes:
|
|
#
|
|
# 1. While the device works normally in Windows, it may be necessary to use
|
|
# a usbhid.quirks setting on RPi. If the adapter isn't recognized as
|
|
# two gamepads, append the following to your cmdline.txt:
|
|
#
|
|
# usbhid.quirks=0x16c0:0x75e1:0x040
|
|
#
|
|
# 2. In order to support 12 inputs per player, some pins that would normally
|
|
# be empty or differently used are repurposed as button inputs. Be sure
|
|
# to read the section at the end of this file that describes these
|
|
# non-standard inputs.
|
|
#
|
|
# 3. Service (pin 14, solder side) isn't connected to anything.
|
|
|
|
input_device_display_name = "3H JAMMA to Dual USB Adapter"
|
|
|
|
#
|
|
# The doubled-up version is used on RPi, possibly related to usbhid.quirks
|
|
#
|
|
input_device = "3H Dual Arcade 3H Dual Arcade"
|
|
#input_device = "3H Dual Arcade"
|
|
|
|
#
|
|
# Hex vid:pid = 16c0:75e1 -> Decimal vid:pid = 5824:30177
|
|
#
|
|
input_vendor_id = "5824"
|
|
input_product_id = "30177"
|
|
|
|
#
|
|
# udev on RPi, xinput on Windows
|
|
#
|
|
input_driver = "udev"
|
|
#input_driver = "xinput"
|
|
|
|
#
|
|
# Standard JAMMA Inputs
|
|
#
|
|
input_up_axis_label = "Joystick Up"
|
|
input_down_axis_label = "Joystick Down"
|
|
input_left_axis_label = "Joystick Left"
|
|
input_right_axis_label = "Joystick Right"
|
|
input_up_axis = "-1"
|
|
input_down_axis = "+1"
|
|
input_left_axis = "-0"
|
|
input_right_axis = "+0"
|
|
|
|
input_a_btn_label = "A/JAMMA22"
|
|
input_b_btn_label = "B/JAMMA23"
|
|
input_x_btn_label = "C/JAMMA24"
|
|
input_y_btn_label = "D/JAMMA25"
|
|
input_a_btn = "0"
|
|
input_b_btn = "1"
|
|
input_x_btn = "2"
|
|
input_y_btn = "3"
|
|
|
|
#
|
|
# JAMMA26 was chosen for Select because that's what the Neo Geo MVS uses
|
|
#
|
|
input_select_btn_label = "Select/JAMMA26"
|
|
input_start_btn_label = "Start/JAMMA17"
|
|
input_select_btn = "4"
|
|
input_start_btn = "7"
|
|
|
|
input_l_btn_label = "Coin/JAMMA16"
|
|
input_r_btn_label = "Test/Tilt/JAMMA15"
|
|
input_l_btn = "8"
|
|
input_r_btn = "9"
|
|
|
|
#
|
|
# The following buttons on non-standard pins and will need special wiring
|
|
# for your cabinet to work properly with them.
|
|
#
|
|
# Notably, pins 27 and 28 are supposed to be grounds.
|
|
#
|
|
# Pin 9 is supposed to be for the coin lockout, which is technically an
|
|
# *output*.
|
|
#
|
|
# Pin 11 shouldn't have anything on it for JAMMA but an MVS cabinet would
|
|
# have mono audio the parts side and test on the solder side. Use this
|
|
# board with caution!
|
|
#
|
|
input_l2_btn_label = "E/JAMMA27"
|
|
input_r2_btn_label = "F/JAMMA28"
|
|
input_l3_btn_label = "G/JAMMA11"
|
|
input_r3_btn_label = "H/JAMMA9"
|
|
input_l2_btn = "5"
|
|
input_r2_btn = "6"
|
|
input_l3_btn = "10"
|
|
input_r3_btn = "11" |