All the sun5i have the SPI2 pins exposed on the PE bank. Add them to the
DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The SPI2 pins on the sun5i PB bank are only available on the A10s. Rename
the A10s only bank so that it doesn't confuse people on the other SoCs
whose indexing would start at b.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The CHIP uses a 1-Wire bus to discover the DIPs. Enable the bus in the DT.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The WiFi chip is powered through a GPIO and two regulators in parallel.
Since that case is not supported yet, just set them as always on before we
rework the regulator framework to deal with those.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The CHIP Pro is a small embeddable board. It features a GR8, an AXP209
PMIC, a 512MB SLC NAND and a WiFi/BT chip.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The UART3 pins were missing from the DTSI. Add them.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The UART2 pins were missing from the DTSI. Add them.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The PWM controller has two different channels, but only the first pin was
exposed in the DTSI. Add the other one.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
There was a dumb copy and paste mistake here, fix it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The GR8 has access to the UART3 controller, which was missing in the
DTSI. Add it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The LCD0 controller on the A31 can do RGB output up to 8 bits per
channel. Add the pins for RGB888 output.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A31 has 2 parallel display pipelines, which can be intermixed.
However the driver currently only supports one of them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
sun7i-a20-olimex-som-evb.dts doesn't contain cpu-supply needed for
voltage-scaling with cpufreq-dt so define it.
The default voltages are defined in sun7i-a20.dtsi.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we have support for the VGA bridges using our DRM driver, enable
the display engine for the Olimex A13-Olinuxino.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The pinmux setting nodes for the A31 were added out of alphabetical
order. Sort them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviews have found that sun5i was a better prefix after all for the GR8.
Rename the relevant device trees before it's too late.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The polarity of the card detect pin is inverted.
Change it to reflect the right polarity for the board
which is ACTIVE_LOW.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
cleanups, GPIO line naming, and the node for the new thermal driver.
-----BEGIN PGP SIGNATURE-----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=CBTE
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=pDtt
-----END PGP SIGNATURE-----
Merge tag 'bcm2835-dt-next-2016-11-18' into devicetree/next
This pull request brings in DT changes for BCM2835: pinctrl setup
cleanups, GPIO line naming, and the node for the new thermal driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This enables the usb otg controller for the lcdk board.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This adds the device tree node for the usb otg
controller present in the da850 family of SoC's.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Child of mvpp2 ethernet do not have a reg property so the unit name
should not contain an address: remove them.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
As it was previously done for kirkwood and for aramda 370/XP, this adds
missing node labels to Armada 375 and SoC specific nodes to allow to
reference them more easily.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The gpio-key nodes do not have a reg property, so remove the address from
the unit name.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The dsa node does not have a reg property, so remove the address from the
unit name.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
l2-cache which is either an aurora-outer-cache or an aurora-system-cache
has a reg property so the unit name should contain an address.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
PCIe has a ranges property, so the unit name should contain an address.
Take the opportunity to use the node label instead of the full name.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
PCIe has a range property, so the unit name should contain an address.
Take the opportunity to use the node label instead of the full name.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
MDIO has a reg property so the unit name should contain an address.
Take the opportunity to use the node label instead of the full name.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Use the node label when possible. As a result it flattens the device tree
and it makes more visible the IP blocks specific to each SoC variant.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
As it was previously done for kirkwood, this adds missing node labels to
Armada 370 and XP common and SoC specific nodes to allow to reference
them more easily.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The cpurst nodes are identical in armada-370.dtsi and armada-xp.dtsi
files, so move it in the common armada-370-xp.dtsi file.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
In the dts for the Marvell Armada XP Matrix board the pcie-controller was
located under the internal-regs node whereas it belongs to the soc node.
It means that, until this fix, the pcie could not work for this board
because it didn't match the definition of the pcie-controller node in the
dtsi file. If we had a look on the decompiled dtb file we saw two
different instances of the pcie-controller node: one with the all the
resource set but disabled and the other without any resource but enabled.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fix a spelling mistake in arch/arm/boot/dts/kirkwood-topkick.dts.
The manufacturer's name is Univer*s*al Scientific Industrial...
Compare with footer of page here:
http://www.usish.com/english/products_topkick1281p2.php
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch converts my orion5x ls-chl Linkstation device to device tree.
[gregory.clement@free-electrons.com: fix title, add back the commit log,
move the removal of the platform in an other patch]
Signed-off-by: Ashley Hughes <ashley.hughes@blueyonder.co.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The SMSC9112 ethernet controller is connected to chip select 2
on the EBI2 bus on the APQ8060 Dragonboard. We set this up by
activating EBI2, creating a chipselect entry as a subnode, and then
putting the ethernet controller in a subnode of the chipselect.
After the chipselect is configured, the SMSC device will be
instantiated.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the external bus interface EBI2 to the MSM8660 device
tree, albeit with status = "disabled" so that devices actually
using EBI2 can turn it on if needed.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add pstore support for the nexus7. This was useful in debugging
a crash where the cpus were getting stuck with irqs off and
serial output wasn't reliably working.
Cc: Kees Cook <keescook@chromium.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Vinay Simha <vinaysimha@inforcecomputing.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add DSI and panel nodes to get graphics up and running
on the Nexus7.
This still depends on the panel driver being present
along with the rpmclk code.
Feedback would be greatly appreciated!
Cc: Archit Taneja <architt@codeaurora.org>
Cc: vinay simha <vinaysimha@inforcecomputing.com>
Cc: andy.gross@linaro.org
Cc: robdclark@gmail.com
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Adds the core gpu, and dsi nodes for the apq8064 needed
to get graphics working on the nexus7 and other devices.
These apply on top of Archit's patch set that enables HDMI for IFC6410
Feedback would be greatly appreciated!
Cc: Archit Taneja <architt@codeaurora.org>
Cc: vinay simha <vinaysimha@inforcecomputing.com>
Cc: andy.gross@linaro.org
Cc: robdclark@gmail.com
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add HDMI support on IFC6410. Populate the regulators required by HDMI-TX
and PHY. Establish the link between the MDP4 DTV encoder and HDMI. Create
a generic micro HDMI connector DT node. The msm drm driver doesn't parse
for HDMI connectors in DT, but it will do so later.
Cc: devicetree@vger.kernel.org
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
