This sets proper connector type for DSI connected panels.
Signed-off-By: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The function is never used, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The function is never used, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The backlight GPIO was supported with platform data only. Now that the
driver only supports DT, the backlight GPIO is never initialized. Remove
it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
To allow supporting displays that need some logic to enable power to the
display try to get a vcc-supply property from the device tree and drive
the resulting regulator accordingly.
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Some displays have a reset input. To assert that the display is
functional the reset gpio must be deasserted.
Teach the driver to get and drive such a gpio accordingly.
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
At the moment we calculate the buffer's pitch with:
pitch = width * DIV_ROUND_UP(bpp, 8)
For CLUT modes with bpp of 1/2/4/8 this gives wrong result, and the
correct pitch is:
pitch = DIV_ROUND_UP(width * bpp, 8)
In practice this doesn't change anything, as we don't support CLUT
modes, but it's better to have the pitch calculation correct.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The previous commit removed aligning the pitch to SGX's pitch
requirement from align_pitch(). What's left is effectively a function
that returns width * bytespp.
To clean up the driver, we can remove the function and have the
calculation inline in the two places which call align_pitch().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
omapdrm checks if the pixel stride is divisible by 8. This is meant to
ensure that the byte stride is 32, which is required by SGX.
The check is not correct, as it checks for pixels, not bytes, and thus
needlessly increases the stride for, e.g., NV12.
Also, SGX driver is not supported in the mainline, and the TI's SGX
driver nowadays does the memory allocation itself and doesn't rely on
omapdrm to figure out the correct pitch.
So we can just remove the whole roundup.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
encoder-opa362.c and panel-sharp-ls037v7dw01.c do not use the legacy
GPIO API, so we can remove the including of gpio.h and of_gpio.h.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Move the contents of the video/omapdss.h header file to omapdrm/dss local
header file and remove the original global header. The omapfb stach is
using video/omapfb_dss.h so this change will complete the separation of the
two driver implementation.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
All drivers to include the omapdrm/dss/omapdss.h header file. This header
includes the <video/omapdss.h>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Clean up the header files regarding to hdmi audio so the omap-hdmi-audio.h
file will only need to include the platform_data/omapdss.h file.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Mark Brown <broonie@kernel.org>
CC: Jyri Sarha <jsarha@ti.com>
CC: Liam Girdwood <liam.r.girdwood@linux.intel.com>
The default_device is no longer used, it is a leftower from legacy. The
else if (pdata->default_device) is always going to be false.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
In legacy mode (non DT mode) support only composite connector type. The
only user for this is rx51, using composite type.
Dropping the connector_type selection via pdata will allow cleanups in
omapdss (drm vs fbdev).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Some panel/encoder/connector driver includes omap-panel-data.h but they
do not need it. Remove the inclusion of video/omap-panel-data.h from these
drivers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
We want to hide drm_atomic_stat internals a bit better.
v2: Use drm_crtc_mask (Maarten).
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464818821-5736-7-git-send-email-daniel.vetter@ffwll.ch
A lot of the display drivers for OMAP use the gpio descriptor functions
that are only available in linux/gpio.h if GPIOLIB is enabled and
otherwise produce a build error:
drivers/gpu/drm/omapdrm/displays/encoder-opa362.c: In function 'opa362_enable':
drivers/gpu/drm/omapdrm/displays/encoder-opa362.c:101:3: error: implicit declaration of function 'gpiod_set_value_cansleep' [-Werror=implicit-function-declaration]
drivers/gpu/drm/omapdrm/displays/panel-dpi.c: In function 'panel_dpi_probe_pdata':
drivers/gpu/drm/omapdrm/displays/panel-dpi.c:189:23: error: implicit declaration of function 'gpio_to_desc' [-Werror=implicit-function-declaration]
drivers/gpu/drm/omapdrm/displays/panel-sharp-ls037v7dw01.c: In function 'sharp_ls_enable':
drivers/gpu/drm/omapdrm/displays/panel-sharp-ls037v7dw01.c:120:3: error: implicit declaration of function 'gpiod_set_value_cansleep' [-Werror=implicit-function-declaration]
This replaces the existing linux/gpio.h with linux/gpio/consumer.h
where needed. In case of panel-lgphilips-lb035q02.c however, we
also have to include linux/gpio.h to get the definition of gpio_is_valid
and gpio_set_value_cansleep that are used for the non-DT case.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[tomi.valkeinen@ti.com: resolved conflicts]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omapdrm driver relies on this header to be included
implicitly, but this does not always work, and I get
this error in randconfig builds:
gpu/drm/omapdrm/dss/hdmi_phy.c: In function 'hdmi_phy_dump':
gpu/drm/omapdrm/dss/hdmi_phy.c:34:2: error: implicit declaration of function 'seq_printf' [-Werror=implicit-function-declaration]
gpu/drm/omapdrm/dss/hdmi_wp.c: In function 'hdmi_wp_dump':
gpu/drm/omapdrm/dss/hdmi_wp.c:26:2: error: implicit declaration of function 'seq_printf' [-Werror=implicit-function-declaration]
gpu/drm/omapdrm/dss/hdmi_pll.c: In function 'hdmi_pll_dump':
gpu/drm/omapdrm/dss/hdmi_pll.c:30:2: error: implicit declaration of function 'seq_printf' [-Werror=implicit-function-declaration]
This adds the #include statements in all files that have
a seq_printf statement.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This reverts commit 1c278e5e3718d15475ec08ee2135f37a6b13361c.
If DRM_OMAP does not select OMAP2_DSS it is possible to build a kernel with
DRM_OMAP only and not selecting OMAP2_DSS. Since omapdrm depends on
OMAP2_DSS this will result on broken kernel build.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
regulator_can_change_voltage() is deprecated and it's use is not necessary
as commit:
6a0028b3dd67b regulator: Deprecate regulator_can_change_voltage()
describers it clearly.
Also, regulator_set_voltage() is misused in the driver, as it is
supposed to be used only in cases where the regulator voltage needs to
be changed dynamically at runtime. In DSS's case, we always want a fixed
voltage, set in the .dts files.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DDC scl high and low times were set to the minimum values
from the i2c specification, but the i2c specification takes into
account the rise time and fall time to calculate the frequency.
To pass HDMI certification DDC can not exceed 100kHz therefore in
a system where the rise times and fall times are negligible the high
and low times for scl need to be 10us.
Signed-off-by: Jim Lodes <jim.lodes@garmin.com>
Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The AVI infoframe R0-R3 in the 2nd data byte represents the
Active Format Aspect Ratio. It is four bits long not two bits.
This fixes that mask used to extract the bits before writing the
bits to the hardware registers.
Signed-off-by: Jim Lodes <jim.lodes@garmin.com>
Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
hdmi_core_powerdown_disable() is supposed to disable HDMI core's
power-down mode. However, the function sets the power-down bit to 0,
which means "enable power-down".
This hasn't caused any issues as the PD seems to affect only interrupts
from HDMI core, and none of those interrupts are used at the moment. CEC
functionality requires core interrupts, and the PD mode needs to be
fixed.
This patch fixes hdmi_core_powerdown_disable() to actually disable the
PD mode.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
With certain kernel config options many omapdrm files fail to compile
due to missing include of linux/gpio/consumer.h and linux/of.h.
This patch adds those includes.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
In some configurations, we can build the OMAP dss driver without
implictly including the pinctrl consumer definitions, causing
a build error:
gpu/drm/omapdrm/dss/dss.c: In function 'dss_runtime_suspend':
gpu/drm/omapdrm/dss/dss.c:1268:2: error: implicit declaration of function 'pinctrl_pm_select_sleep_state' [-Werror=implicit-function-declaration]
This adds an explicit #include.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Originally DSS only had DSI PLLs, and thus the DPI driver has functions
and variables that refer to DSI or DSI PLL. Now we support DSI, VIDEO
and HDMI PLLs, so it's time to remove the DSI references from the code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Type A and B PLLs require a bit different calculations for the clock
rates. DPI driver supports only type A PLLs.
This patch adds support for the type B PLL.
Type B PLLs are simpler than type A, as type B can produce a good clock
for almost any rate. Thus we can just ask it to produce the pixel clock
and use one as LCK and PCK dividers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dss_pll_calc_b() takes HDMI TMDS clock rate as a parameter. To make
dss_pll_calc_b() usable for non-HDMI users, change the function to take
clkout rate as parameter, and also change the current users of
dss_pll_calc_b() to accommodate that.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move hdmi_pll_compute(), used to calculate the config for HDMI PLL, from
hdmi_pll.c to pll.c, with the name of dss_pll_calc_b(), to make it
available to non-HDMI users.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add a "_a" postfix to the type A PLL calc functions, to differentiate
them from the type B PLL calculations which we will add shortly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
To make it possible to use HDMI PLL for other video outputs than HDMI,
the HDMI PLL code needs to do runtime_get/put for the HDMI IP, so that
the IP (include the PLL) is enabled.
To do that we also need to store the HDMI pdev in the hdmi_pll_data.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DPI driver uses a fixed clkout index, 0. This has worked fine as the
first clkout is usually used.
To generalize the code and to support additional clock sources, change
the code to use dss_pll_get_clkout_idx_for_src() to get the clkout
index.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We can clean up the DPI driver's clock source handling by using the
dss_clk_source instead of only a dss_pll pointer.
This will also make it possible to use additional clock sources, like
PLL1_3 or HDMI_PLL, which the code did not support earlier.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
With the new PLL helpers, we can clean up the dispc_fclk_rate(). This
will also make dispc_fclk_rate() support clock sources it didn't support
earlier.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
With the new PLL helpers, we can clean up the dispc_mgr_lclk_rate().
This will also make dispc_mgr_lclk_rate() support clock sources it
didn't support earlier.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add two PLL helper functions:
dss_pll_find_by_src() which returns the dss_pll for the given
dss_clk_source.
dss_pll_get_clkout_idx_for_src() which returns the clkout index for the
given dss_clk_source.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The code to set the clock muxes for DISPC's LCD clock inputs is very
confusing. Especially on DRA7, there's an additional clock muxing that
needs to be done, which at the moment is done in dpi.c using
dss_ctrl_pll_set_control_mux().
Clean this all up by:
- Using dss_clk_source instead of dss_pll_id, as dss_pll_id doesn't
specify the clock source quite correctly.
- Splitting the dss_select_lcd_clk_source() up into DSS version specific
helper functions.
- Using dss_ctrl_pll_set_control_mux() from the helper functions, so
that dpi.c doesn't have to call it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DSS uses two types of PLLs, type A (DSI & Video) and type B (HDMI). The
two types behave slightly differently, but we don't have the type of the
PLL available anywhere for the driver.
This patch adds an enum for the PLL type and a field in the PLL's HW
data to store it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
enum dss_clk_source does not have values for all clock sources available
on OMAP4+ DSS versions. Add the missing clock sources.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The names of the enum dss_clk_source's values are legacy names, only
correct for OMAP3 DSS. Rename the names to more generic ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now that there is no "non-generic" version of the function to get the
clock source name, lets rename dss_get_generic_clk_source_name() to
dss_get_clk_source_name().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We have two functions to return a name for clock sources for debugging
purposes: dss_feat_get_clk_source_name() and
dss_get_generic_clk_source_name().
The former is supposed to return a DSS IP version specific name for the
clock source, and the latter is supposed to return a more generic name.
All this seems a bit pointless, so let's remove the former one.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
'enum omap_dss_clk_source' is internal to dss. Let's rename it to
'dss_clk_source' match our naming convention.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
At the moment 'enum omap_dss_clk_source' is in omapdss.h, shared by
omapdrm and omapfb. We're about to improve the omapdrm clock code, so we
need to make a separate copy of the enum for each driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Video pll hw data is missing bitfield definitions for clkout2 and
clkout3. We don't use those clkouts at the moment, so this has not
caused any issues.
Add the bitfields.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
