Currently in switchdev mode we allow only for raw packet QPs.
Expose the right capabilities and set the gid table length to 0, also
make sure we don't try to enable RoCE, so split the function
to enable RoCE so representors can enable only the notifier needed for
net device events.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
A flow DB is a shared resource between PF and representors,
need to allocate it only when creating the PF IB device.
Once we add IB representors, they will use the flow db which was
created by the PF.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Create the basic infrastructure of registering and unregistering
IB representors. The load/unload callbacks are left empty and
proper implementation will be introduced in following patches.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The current implementation of create CQ requires contiguous
memory, such requirement is problematic once the memory is
fragmented or the system is low in memory, it causes for
failures in dma_zalloc_coherent().
This patch implements new scheme of fragmented CQ to overcome
this issue by introducing new type: 'struct mlx5_frag_buf_ctrl'
to allocate fragmented buffers, rather than contiguous ones.
Base the Completion Queues (CQs) on this new fragmented buffer.
It fixes following crashes:
kworker/29:0: page allocation failure: order:6, mode:0x80d0
CPU: 29 PID: 8374 Comm: kworker/29:0 Tainted: G OE 3.10.0
Workqueue: ib_cm cm_work_handler [ib_cm]
Call Trace:
[<>] dump_stack+0x19/0x1b
[<>] warn_alloc_failed+0x110/0x180
[<>] __alloc_pages_slowpath+0x6b7/0x725
[<>] __alloc_pages_nodemask+0x405/0x420
[<>] dma_generic_alloc_coherent+0x8f/0x140
[<>] x86_swiotlb_alloc_coherent+0x21/0x50
[<>] mlx5_dma_zalloc_coherent_node+0xad/0x110 [mlx5_core]
[<>] ? mlx5_db_alloc_node+0x69/0x1b0 [mlx5_core]
[<>] mlx5_buf_alloc_node+0x3e/0xa0 [mlx5_core]
[<>] mlx5_buf_alloc+0x14/0x20 [mlx5_core]
[<>] create_cq_kernel+0x90/0x1f0 [mlx5_ib]
[<>] mlx5_ib_create_cq+0x3b0/0x4e0 [mlx5_ib]
Signed-off-by: Yonatan Cohen <yonatanc@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The flags field the enum is used with comes directly from the uapi
so it belongs in the uapi headers for clarity and so userspace can
use it.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This patch maps the new page to user space applications to
allow converting a user space completion timestamp to system wall
time at the lowest possible latency cost.
By using a versioning scheme we allow compatibility between current
and future userspace libraries.
The change moves mlx5_ib_mmap_cmd enum from mlx5_ib.h to the
abi header file mlx5-abi.h.
Reviewed-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Eitan Rabin <rabin@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Update the counter interface for multiple ports. Some counter sets
always comes from the primary device.
Port specific counters should be accessed per mlx5_core_dev not always
through the IB master mdev.
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
When there are multiple ports for single IB(RoCE) device, support
debugfs entries to be available for each port.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
When mlx5_ib_add is called determine if the mlx5 core device being
added is capable of dual port RoCE operation. If it is, determine
whether it is a master device or a slave device using the
num_vhca_ports and affiliate_nic_vport_criteria capabilities.
If the device is a slave, attempt to find a master device to affiliate it
with. Devices that can be affiliated will share a system image guid. If
none are found place it on a list of unaffiliated ports. If a master is
found bind the port to it by configuring the port affiliation in the NIC
vport context.
Similarly when mlx5_ib_remove is called determine the port type. If it's
a slave port, unaffiliate it from the master device, otherwise just
remove it from the unaffiliated port list.
The IB device is registered as a multiport device, even if a 2nd port is
not available for affiliation. When the 2nd port is affiliated later the
GID cache must be refreshed in order to get the default GIDs for the 2nd
port in the cache. Export roce_rescan_device to provide a mechanism to
refresh the cache after a new port is bound.
In a multiport configuration all IB object (QP, MR, PD, etc) related
commands should flow through the master mlx5_core_dev, other commands
must be sent to the slave port mlx5_core_mdev, an interface is provide
to get the correct mdev for non IB object commands.
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
When multiple RoCE ports are supported registration for events on
multiple netdevs is required. Refactor the event registration and
handling to support multiple ports.
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
A DC Target (DCT) QP is represented in the hardware as a unique object.
This object is created by CREATE_DCT command and destroyed by DESTROY_DCT
command. However, in the driver we describe it as a QP.
The hardware command that creates a DCT needs parameters that the verb
create_qp() does not provide. Those remaining parameters are provided
with the call to the verb modify_qp(). Therefore we delay the actual
creation of a DCT in the hardware until the stage of modify_qp() to RTR.
A support for query_qp() was added as well. It uses QUERY_DCT command to
retrieve the applicable fields.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The QP type IB_QPT_DRIVER doesn't describe the transport or the service
that the QP provides but those are known only to the hardware driver.
The actual type of the QP is stored in the hardware driver context (i.e.
mlx5_qp) under the field qp_sub_type.
Take the real QP type and any extra data that is required to create the QP
from the driver channel and modify the QP initial attributes before continuing
with create_qp().
Downstream patches from this series will add support for both DCI and
DCT driver QPs.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Unconditional locks/list and ODP srcu initialization should be done in
the INIT stage. Remove those from the CAPS stage and move them to the
proper stage.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The loopback stage only initializes a lock, move it to be in
the CAPS initialization phase and get rid loopback step completely.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Today we have single function which is used when we add an IB interface,
break this function into multiple functions.
Create stages and a generic mechanism to execute each stage.
This is in preparation for RDMA/IB representors which might not need
all stages or will do things differently in some of the stages.
This patch doesn't change any functionality.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This patch enables QP creation with a given BF index, this allows the
user space driver to share same BF between few QPs or alternatively have
a dedicated BF per QP.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This patch exposes the option to dynamic allocates a UAR, this
functionality will be used in downstream patch in this series as
part of QP creation.
Specifically, the user space driver asks for a UAR allocation in a given
page index, upon success this UAR and its bfregs can be used as part of
QP creation by the user space driver.
To enable allocating more than 256 UARs the page index is encoded in an
extra one byte just after the command byte.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This patch extends the alloc context flow to be prepared for working
with dynamic UAR allocations.
Currently upon alloc context there is some fix size of UARs that are
allocated (named 'static allocation') and there is no option to user
application to ask for more or control which UAR will be used by which
QP.
In this patch the driver prepares its data structures to manage both the
static and the dynamic allocations and let the user driver knows about
the max value of dynamic blue-flame registers that are allowed.
Downstream patches from this series will enable the dynamic allocation
and the association as part of QP creation.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
User-space applications can do mmap and munmap directly at
any time.
Since the VMA list is not protected with a mutex, concurrent
accesses to the VMA list from the mmap and munmap can cause
data corruption. Add a mutex around the list.
Cc: <stable@vger.kernel.org> # v4.7
Fixes: 7c2344c3bbf9 ("IB/mlx5: Implements disassociate_ucontext API")
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Add the PCI write end padding flag to device_cap_flags enum and set it
during mlx5_ib_query_device so it will be reported to user-space.
During WQ/QP creation, set that capability for WQ/QP if user requested
it and HW supports it.
PCI write end padding modification is not supported for now. There's no
such flag for a QP but for a WQ, create and modify use the same flag.
Return an error if PCI write end padding flag is set during modify_wq.
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The device can support receive Stateless Offloads for the inner
packet's fields only when the packet is processed by TIR which is
enabled to support tunneling. Otherwise, the device treats the
packet as an ordinary non-tunneling packet and receive offloads
can be done only for the outer packet's field.
In order to enable receive Stateless Offloading support for incoming
tunneling traffic the TIR should be created with tunneled_offload_en.
Tunneling offloads is supported only be raw ethernet QP.
This patch includes:
* New QP creation flag for tunneling offloads.
* Reports device capabilities.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In some benchmarks and some CPU architectures, writing the CQE on a full
cache line size improves performance by saving memory access operations
(read-modify-write) relative to partial cache line change. This patch
lets the user to configure the device to pad the CQE up to 128B in case
its content is less than 128B. Currently the driver supports only padding
for a CQE size of 128B.
Signed-off-by: Guy Levi <guyle@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Allow creation of a multi-packet receive queue.
In order to create a multi-packet RQ, the following fields in
the mlx5_ib_rwq should be set:
- log_num_strides: Log of number of strides per WQE
- single_stride_log_num_of_bytes: Log of a single stride size
- two_byte_shift_en: When enabled, hardware pads 2 bytes of zeros
before writing the message to memory (e.g. for the IP alignment).
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch reports the device's striding RQ capabilities to
the user-space:
- min/max_single_stride_log_num_of_bytes: Log of min/max number of
bytes in a single stride.
- min/max_single_wqe_log_num_of_strides: Log of min/max number of
strides in a single WQE.
- supported_qpts: A bit mask to know which QP types support multi-
packet RQ, for now only Raw Packet QPs.
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch is the first step in decoupling UMR usage and
allocation from the MR cache. The only functional change
in this patch is to enables UMR for MRs created with
reg_create.
This change fixes a bug where ODP memory regions that
were not allocated from the MR cache did not have UMR
enabled.
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Allow user space applications to accelerate send and receive
traffic which is typically handled by IPoIB ULP by creating
a UD QP with a given source QPN of the IPoIB UD QP.
UD QP with a given source QPN should basically be similar to
RAW QP from point of view of its created resources.
However,
- Its TIS should point to the source QPN.
- Modify can be done only on its state as the transport attributes
are managed by its source QP.
This patch manages below:
- Creating/destroying/modifying UD QP with a given source QPN.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add debugfs interface for monitor the number of delay drop timeout
events and the number of existing dropless RQs in the system.
In addition add debugfs interface for configuring the global timeout value
which is used in the SET_DELAY_DROP command.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
RQs that were configured for "delay drop" will prevent packet drops
when their WQEs are depleted.
Marking an RQ to be drop-less is done by setting delay_drop_en in RQ
context using CREATE_RQ command.
Since this feature is globally activated/deactivated by using the
SET_DELAY_DROP command on all the marked RQs, we activated/deactivated
it according to the number of RQs with 'delay_drop' enabled.
When timeout is expired, then the feature is deactivated. Therefore
the driver handles the delay drop timeout event and reactivate it.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch adds debug control parameters for congestion control which
can be read or written through debugfs. They are for reaction point and
notification point nodes.
These control parameters are as below:
+------------------------------+-----------------------------------------+
| Name | Description |
|------------------------------+-----------------------------------------|
|rp_clamp_tgt_rate | When set target rate is updated to |
| | current rate |
|------------------------------+-----------------------------------------|
|rp_clamp_tgt_rate_ati | When set update target rate based on |
| | timer as well |
|------------------------------+-----------------------------------------|
|rp_time_reset | time between rate increase if no |
| | CNP is received unit in usec |
|------------------------------+-----------------------------------------|
|rp_byte_reset | Number of bytes between rate inease if |
| | no CNP is received |
|------------------------------+-----------------------------------------|
|rp_threshold | Threshold for reaction point rate |
| | control |
|------------------------------+-----------------------------------------|
|rp_ai_rate | Rate for target rate, unit in Mbps |
|------------------------------+-----------------------------------------|
|rp_hai_rate | Rate for hyper increase state |
| | unit in Mbps |
|------------------------------+-----------------------------------------|
|rp_min_dec_fac | Minimum factor by which the current |
| | transmit rate can be changed when |
| | processing a CNP, unit is percerntage |
|------------------------------+-----------------------------------------|
|rp_min_rate | Minimum value for rate limit, |
| | unit in Mbps |
|------------------------------+-----------------------------------------|
|rp_rate_to_set_on_first_cnp | Rate that is set when first CNP is |
| | received, unit is Mbps |
|------------------------------+-----------------------------------------|
|rp_dce_tcp_g | Used to calculate alpha |
|------------------------------+-----------------------------------------|
|rp_dce_tcp_rtt | Time between updates of alpha value, |
| | unit is usec |
|------------------------------+-----------------------------------------|
|rp_rate_reduce_monitor_period | Minimum time between consecutive rate |
| | reductions |
|------------------------------+-----------------------------------------|
|rp_initial_alpha_value | Initial value of alpha |
|------------------------------+-----------------------------------------|
|rp_gd | When CNP is received, flow rate is |
| | reduced based on gd, rp_gd is given as |
| | log2(rp_gd) |
|------------------------------+-----------------------------------------|
|np_cnp_dscp | dscp code point for generated cnp |
|------------------------------+-----------------------------------------|
|np_cnp_prio_mode | 802.1p priority for generated cnp |
|------------------------------+-----------------------------------------|
|np_cnp_prio | cnp priority mode |
+------------------------------+-----------------------------------------+
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The old logic ignored link state. This led to missing IB events like
when link goes down on the switch while admin state is up or to redundant
events like when admin state goes up while link is down.
To fix that, probe the port state on NETDEV events and compare to last
known state to decide if IB events needs to be dispatched.
FIxes: 5ec8c83e3ad3 ("IB/mlx5: Port events in RoCE now rely on netdev events")
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Currently, unicast/multicast loopback raw ethernet
(non-RDMA) packets are sent back to the vport.
A unicast loopback packet is the packet with destination
MAC address the same as the source MAC address.
For multicast, the destination MAC address is in the
vport's multicast filter list.
Moreover, the local loopback is not needed if
there is one or none user space context.
After this patch, the raw ethernet unicast and multicast
local loopback are disabled by default. When there is more
than one user space context, the local loopback is enabled.
Note that when local loopback is disabled, raw ethernet
packets are not looped back to the vport and are forwarded
to the next routing level (eswitch, or multihost switch,
or out to the wire depending on the configuration).
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Cache the needed umr_fence and set the wqe ctrl segmennt
accordingly.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Acked-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch simply renames struct ib_ah_attr to
rdma_ah_attr as these fields specify attributes that are
not necessarily specific to IB.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Don Hiatt <don.hiatt@intel.com>
Reviewed-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Internally MW implemented as KLM MKey and filled by userspace UMR
postsends. Handle pagefault trigered by operations on this MKeys.
Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch adds support to query the congestion related hardware counters
through new command and links them with other hw counters being available
in hw_counters sysfs location.
In order to reuse existing infrastructure it renames related q_counter
data structures to more generic counters to reflect q_counters and
congestion counters and maybe some other counters in the future.
New hardware counters:
* rp_cnp_handled - CNP packets handled by the reaction point
* rp_cnp_ignored - CNP packets ignored by the reaction point
* np_cnp_sent - CNP packets sent by notification point to respond to
CE marked RoCE packets
* np_ecn_marked_roce_packets - CE marked RoCE packets received by
notification point
It also avoids returning ENOSYS which is specific for invalid
system call and produces the following checkpatch.pl warning.
WARNING: ENOSYS means 'invalid syscall nr' and nothing else
+ return -ENOSYS;
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Implement mlx5e's IPoIB SKB transmit using the helper functions provided
by mlx5e ethernet tx flow, the only difference in the code between
mlx5e_xmit and mlx5i_xmit is that IPoIB has some extra fields to fill
(UD datagram segment) in the TX descriptor (WQE) and it doesn't need to
have any vlan handling.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add implicit MR, covering entire user address space.
The MR is implemented as an indirect KSM MR consisting of
1GB direct MRs.
Pages and direct MRs are added/removed to MR by ODP.
Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Allow other parts of mlx5_ib to use MR cache mechanism.
* Add new functions mlx5_mr_cache_alloc and mlx5_mr_cache_free
* Traditional MTT MKey buckets are limited by MAX_UMR_CACHE_ENTRY
Additinal buckets may be added above.
Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Enable creating a RAW Ethernet QP with cvlan stripping offload when
it's supported by the hardware.
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch modify the Q counters implementation, so each one of the
three Q counters groups will be exposed by the driver only if they are
supported by the firmware.
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
For Routable RoCE QPs, the DSCP should be set in the QP's
address path.
The DSCP's value is derived from the traffic class.
Fixes: 2811ba51b049 ("IB/mlx5: Add RoCE fields to Address Vector")
Cc: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Current check requests that new fields in struct
mlx5_ib_alloc_ucontext_req_v2 that are not known to the driver be zero.
This was introduced so new libraries passing additional information to
the kernel through struct mlx5_ib_alloc_ucontext_req_v2 will be notified
by old kernels that do not support their request by failing the
operation. This schecme is problematic since it requires libmlx5 to issue
the requests with descending input size for struct
mlx5_ib_alloc_ucontext_req_v2.
To avoid this, we require that new features that will obey the following
rules:
If the feature requires one or more fields in the response and the at
least one of the fields can be encoded such that a zero value means the
kernel ignored the request then this field will provide the indication
to the library. If no response is required or if zero is a valid
response, a new field should be added that indicates to the library
whether its request was processed.
Fixes: b368d7cb8ceb ('IB/mlx5: Add hca_core_clock_offset to udata in init_ucontext')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Make use of the blue flame registers allocator at mlx5_ib. Since blue
flame was not really supported we remove all the code that is related to
blue flame and we let all consumers to use the same blue flame register.
Once blue flame is supported we will add the code. As part of this patch
we also move the definition of struct mlx5_bf to mlx5_ib.h as it is only
used by mlx5_ib.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This establishes a solid naming conventions for UARs. A UAR (User Access
Region) can have size identical to a system page or can be fixed 4KB
depending on a value queried by firmware. Each UAR always has 4 blue
flame register which are used to post doorbell to send queue. In
addition, a UAR has section used for posting doorbells to CQs or EQs. In
this patch we change names to reflect this conventions.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
* Update page fault event according to last specification.
* Separate code path for page fault EQ, completion EQ and async EQ.
* Move page fault handling work queue from mlx5_ib static variable
into mlx5_core page fault EQ.
* Allocate memory to store ODP event dynamically as the
events arrive, since in atomic context - use mempool.
* Make mlx5_ib page fault handler run in process context.
Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this change we turn mlx5_ib_update_mtt() into generic
mlx5_ib_update_xlt() to perfrom HCA translation table modifiactions
supporting both atomic and process contexts and not limited by number
of modified entries.
Using this function we increase preallocated MRs up to 16GB.
Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of extended UMR translation offset.
Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Update struct mlx5_wqe_umr_ctrl_seg.
* Currenlty UMR send_flags aim only certain use cases: enabled/disable
cached MR, modifying XLT for ODP. By making flags independent make UMR
more flexible allowing arbitrary manipulations.
* Since different UMR formats have different entry sizes UMR request
should receive exact size of translation table update instead of
number of entries. Rename field npages to xlt_size in struct mlx5_umr_wr
and update relevant code accordingly.
* Add support of length64 bit.
Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Shared mlx5 updates with net stack (will drop out on merge if Dave's
tree has already been merged)
- Driver updates: cxgb4, hfi1, hns-roce, i40iw, mlx4, mlx5, qedr, rxe
- Debug cleanups
- New connection rejection helpers
- SRP updates
- Various misc fixes
- New paravirt driver from vmware
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJYUbAPAAoJELgmozMOVy/dMXcP/iuG5MNzfN8Ny1JftyBQGWg3
cqoQ2OLj9CsXjwVB+5EqbcZHRZY852lKONaLoDKkIOx4YAXO2YuIKOp944vN7EQx
96wfqzT1F5jzAcy5mYZXgLaStGFDAwejKMqeHd0LfJj3OEtemGnVPWYzyqSQmSKo
dzJraS1Z9GIRppzU5WaRpB9PtRBkqIqGJ5vZ0EKLGhed5hYY5r0iMJB0GfriMRDO
lJ4UUVfpsAoLPnqDBFH6IMn2V2UeAw9IR5zNa1mrM1RBfvt/uYTxrw1w3p9WoaNs
GRodhk4DCeAfeyqzVPNBLyXZ4Zq4FzGe3UWM4qysJ1RR4oFNw9Cuw0Fqk8mrfznr
7hv5TpGIckRZiKf8l6e+qLirF0qGtXJg29j2vPVQI9i5nSj95g1agA81PnLQlLLb
flWyxeMj81my7lfMHN1xcV6pqPEKMCOysZmfcvVfJd2XxpjuVD7ekl/YXWp8o8kU
YPdQMqPD626XsD8VpPdMszb9FPmx0JD0HEv+Y1rIFX8JegEI+c3H2X0dqC27T/Ou
FEPWOy025EgHm0Fh/7eIzkG6tjZ4JHoCugJAcxNZGj2XW4eB6r5vY8UwJ8iQRv+n
PVYHiy0UoIRePh0mrdOSSphGZMi/GO/DsqKwCtAMEK43WqZQju6wR7QSIGkh66mp
4uSHJqpf3YEYylxGMhk3
=QeGy
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"This is the complete update for the rdma stack for this release cycle.
Most of it is typical driver and core updates, but there is the
entirely new VMWare pvrdma driver. You may have noticed that there
were changes in DaveM's pull request to the bnxt Ethernet driver to
support a RoCE RDMA driver. The bnxt_re driver was tentatively set to
be pulled in this release cycle, but it simply wasn't ready in time
and was dropped (a few review comments still to address, and some
multi-arch build issues like prefetch() not working across all
arches).
Summary:
- shared mlx5 updates with net stack (will drop out on merge if
Dave's tree has already been merged)
- driver updates: cxgb4, hfi1, hns-roce, i40iw, mlx4, mlx5, qedr, rxe
- debug cleanups
- new connection rejection helpers
- SRP updates
- various misc fixes
- new paravirt driver from vmware"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (210 commits)
IB: Add vmw_pvrdma driver
IB/mlx4: fix improper return value
IB/ocrdma: fix bad initialization
infiniband: nes: return value of skb_linearize should be handled
MAINTAINERS: Update Intel RDMA RNIC driver maintainers
MAINTAINERS: Remove Mitesh Ahuja from emulex maintainers
IB/core: fix unmap_sg argument
qede: fix general protection fault may occur on probe
IB/mthca: Replace pci_pool_alloc by pci_pool_zalloc
mlx5, calc_sq_size(): Make a debug message more informative
mlx5: Remove a set-but-not-used variable
mlx5: Use { } instead of { 0 } to init struct
IB/srp: Make writing the add_target sysfs attr interruptible
IB/srp: Make mapping failures easier to debug
IB/srp: Make login failures easier to debug
IB/srp: Introduce a local variable in srp_add_one()
IB/srp: Fix CONFIG_DYNAMIC_DEBUG=n build
IB/multicast: Check ib_find_pkey() return value
IPoIB: Avoid reading an uninitialized member variable
IB/mad: Fix an array index check
...
