third_party_f2fs-tools/fsck/main.c

655 lines
14 KiB
C
Raw Normal View History

f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
/**
* main.c
*
* Copyright (c) 2013 Samsung Electronics Co., Ltd.
* http://www.samsung.com/
* Copyright (c) 2015 Jaegeuk Kim <jaegeuk@kernel.org>
* : implement defrag.f2fs
* Copyright (C) 2015 Huawei Ltd.
* Hou Pengyang <houpengyang@huawei.com>
* Liu Shuoran <liushuoran@huawei.com>
* Jaegeuk Kim <jaegeuk@kernel.org>
* : add sload.f2fs
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include "fsck.h"
#include <libgen.h>
#include <ctype.h>
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
struct f2fs_fsck gfsck;
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
void fsck_usage()
{
MSG(0, "\nUsage: fsck.f2fs [options] device\n");
MSG(0, "[options]:\n");
MSG(0, " -a check/fix potential corruption, reported by f2fs\n");
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
MSG(0, " -d debug level [default:0]\n");
MSG(0, " -f check/fix entire partition\n");
MSG(0, " -p preen mode [default:0 the same as -a [0|1]]\n");
MSG(0, " -t show directory tree [-d -1]\n");
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
exit(1);
}
void dump_usage()
{
MSG(0, "\nUsage: dump.f2fs [options] device\n");
MSG(0, "[options]:\n");
MSG(0, " -d debug level [default:0]\n");
MSG(0, " -i inode no (hex)\n");
MSG(0, " -n [NAT dump segno from #1~#2 (decimal), for all 0~-1]\n");
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
MSG(0, " -s [SIT dump segno from #1~#2 (decimal), for all 0~-1]\n");
MSG(0, " -a [SSA dump segno from #1~#2 (decimal), for all 0~-1]\n");
MSG(0, " -b blk_addr (in 4KB)\n");
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
exit(1);
}
void defrag_usage()
{
MSG(0, "\nUsage: defrag.f2fs [options] device\n");
MSG(0, "[options]:\n");
MSG(0, " -d debug level [default:0]\n");
MSG(0, " -s start block address [default: main_blkaddr]\n");
MSG(0, " -l length [default:512 (2MB)]\n");
MSG(0, " -t target block address [default: main_blkaddr + 2MB]\n");
MSG(0, " -i set direction as shrink [default: expand]\n");
exit(1);
}
void resize_usage()
{
MSG(0, "\nUsage: resize.f2fs [options] device\n");
MSG(0, "[options]:\n");
MSG(0, " -d debug level [default:0]\n");
MSG(0, " -t target sectors [default: device size]\n");
exit(1);
}
void sload_usage()
{
MSG(0, "\nUsage: sload.f2fs [options] device\n");
MSG(0, "[options]:\n");
MSG(0, " -f source directory [path of the source directory]\n");
MSG(0, " -t mount point [prefix of target fs path, default:/]\n");
MSG(0, " -d debug level [default:0]\n");
exit(1);
}
static int is_digits(char *optarg)
{
int i;
for (i = 0; i < strlen(optarg); i++)
if (!isdigit(optarg[i]))
break;
return i == strlen(optarg);
}
static void error_out(char *prog)
{
if (!strcmp("fsck.f2fs", prog))
fsck_usage();
else if (!strcmp("dump.f2fs", prog))
dump_usage();
else if (!strcmp("defrag.f2fs", prog))
defrag_usage();
else if (!strcmp("resize.f2fs", prog))
resize_usage();
else if (!strcmp("sload.f2fs", prog))
sload_usage();
else
MSG(0, "\nWrong progam.\n");
}
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
void f2fs_parse_options(int argc, char *argv[])
{
int option = 0;
char *prog = basename(argv[0]);
int err = NOERROR;
if (argc < 2) {
MSG(0, "\tError: Device not specified\n");
error_out(prog);
}
c.devices[0].path = strdup(argv[argc - 1]);
argv[argc-- - 1] = 0;
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
if (!strcmp("fsck.f2fs", prog)) {
const char *option_string = ":ad:fp:t";
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
c.func = FSCK;
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
while ((option = getopt(argc, argv, option_string)) != EOF) {
switch (option) {
case 'a':
c.auto_fix = 1;
MSG(0, "Info: Fix the reported corruption.\n");
break;
case 'p':
/* preen mode has different levels:
* 0: default level, the same as -a
* 1: check meta
*/
if (optarg[0] == '-') {
c.preen_mode = PREEN_MODE_0;
optind--;
break;
} else if (!is_digits(optarg)) {
err = EWRONG_OPT;
break;
}
c.preen_mode = atoi(optarg);
if (c.preen_mode < 0)
c.preen_mode = PREEN_MODE_0;
else if (c.preen_mode >= PREEN_MODE_MAX)
c.preen_mode = PREEN_MODE_MAX - 1;
if (c.preen_mode == PREEN_MODE_0)
c.auto_fix = 1;
MSG(0, "Info: Fix the reported corruption in "
"preen mode %d\n", c.preen_mode);
break;
case 'd':
if (optarg[0] == '-') {
err = ENEED_ARG;
break;
} else if (!is_digits(optarg)) {
err = EWRONG_OPT;
break;
}
c.dbg_lv = atoi(optarg);
MSG(0, "Info: Debug level = %d\n", c.dbg_lv);
break;
case 'f':
c.fix_on = 1;
MSG(0, "Info: Force to fix corruption\n");
break;
case 't':
c.dbg_lv = -1;
break;
case ':':
if (optopt == 'p') {
MSG(0, "Info: Use default preen mode\n");
c.preen_mode = PREEN_MODE_0;
c.auto_fix = 1;
} else {
option = optopt;
err = ENEED_ARG;
break;
}
break;
case '?':
option = optopt;
default:
err = EUNKNOWN_OPT;
break;
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
}
if (err != NOERROR)
break;
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
}
} else if (!strcmp("dump.f2fs", prog)) {
const char *option_string = "d:i:n:s:a:b:";
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
static struct dump_option dump_opt = {
.nid = 0, /* default root ino */
.start_nat = -1,
.end_nat = -1,
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
.start_sit = -1,
.end_sit = -1,
.start_ssa = -1,
.end_ssa = -1,
.blk_addr = -1,
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
};
c.func = DUMP;
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
while ((option = getopt(argc, argv, option_string)) != EOF) {
int ret = 0;
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
switch (option) {
case 'd':
if (!is_digits(optarg)) {
err = EWRONG_OPT;
break;
}
c.dbg_lv = atoi(optarg);
MSG(0, "Info: Debug level = %d\n",
c.dbg_lv);
break;
case 'i':
if (strncmp(optarg, "0x", 2))
ret = sscanf(optarg, "%d",
&dump_opt.nid);
else
ret = sscanf(optarg, "%x",
&dump_opt.nid);
break;
case 'n':
ret = sscanf(optarg, "%d~%d",
&dump_opt.start_nat,
&dump_opt.end_nat);
break;
case 's':
ret = sscanf(optarg, "%d~%d",
&dump_opt.start_sit,
&dump_opt.end_sit);
break;
case 'a':
ret = sscanf(optarg, "%d~%d",
&dump_opt.start_ssa,
&dump_opt.end_ssa);
break;
case 'b':
if (strncmp(optarg, "0x", 2))
ret = sscanf(optarg, "%d",
&dump_opt.blk_addr);
else
ret = sscanf(optarg, "%x",
&dump_opt.blk_addr);
break;
default:
err = EUNKNOWN_OPT;
break;
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
}
ASSERT(ret >= 0);
if (err != NOERROR)
break;
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
}
c.private = &dump_opt;
} else if (!strcmp("defrag.f2fs", prog)) {
const char *option_string = "d:s:l:t:i";
c.func = DEFRAG;
while ((option = getopt(argc, argv, option_string)) != EOF) {
int ret = 0;
switch (option) {
case 'd':
if (!is_digits(optarg)) {
err = EWRONG_OPT;
break;
}
c.dbg_lv = atoi(optarg);
MSG(0, "Info: Debug level = %d\n",
c.dbg_lv);
break;
case 's':
if (strncmp(optarg, "0x", 2))
ret = sscanf(optarg, "%"PRIu64"",
&c.defrag_start);
else
ret = sscanf(optarg, "%"PRIx64"",
&c.defrag_start);
break;
case 'l':
if (strncmp(optarg, "0x", 2))
ret = sscanf(optarg, "%"PRIu64"",
&c.defrag_len);
else
ret = sscanf(optarg, "%"PRIx64"",
&c.defrag_len);
break;
case 't':
if (strncmp(optarg, "0x", 2))
ret = sscanf(optarg, "%"PRIu64"",
&c.defrag_target);
else
ret = sscanf(optarg, "%"PRIx64"",
&c.defrag_target);
break;
case 'i':
c.defrag_shrink = 1;
break;
default:
err = EUNKNOWN_OPT;
break;
}
ASSERT(ret >= 0);
if (err != NOERROR)
break;
}
} else if (!strcmp("resize.f2fs", prog)) {
const char *option_string = "d:t:";
c.func = RESIZE;
while ((option = getopt(argc, argv, option_string)) != EOF) {
int ret = 0;
switch (option) {
case 'd':
if (!is_digits(optarg)) {
err = EWRONG_OPT;
break;
}
c.dbg_lv = atoi(optarg);
MSG(0, "Info: Debug level = %d\n",
c.dbg_lv);
break;
case 't':
if (strncmp(optarg, "0x", 2))
ret = sscanf(optarg, "%"PRIu64"",
&c.target_sectors);
else
ret = sscanf(optarg, "%"PRIx64"",
&c.target_sectors);
break;
default:
err = EUNKNOWN_OPT;
break;
}
ASSERT(ret >= 0);
if (err != NOERROR)
break;
}
} else if (!strcmp("sload.f2fs", prog)) {
const char *option_string = "d:f:t:";
c.func = SLOAD;
while ((option = getopt(argc, argv, option_string)) != EOF) {
switch (option) {
case 'd':
if (!is_digits(optarg)) {
err = EWRONG_OPT;
break;
}
c.dbg_lv = atoi(optarg);
MSG(0, "Info: Debug level = %d\n",
c.dbg_lv);
break;
case 'f':
c.from_dir = (char *)optarg;
break;
case 't':
c.mount_point = (char *)optarg;
break;
default:
err = EUNKNOWN_OPT;
break;
}
if (err != NOERROR)
break;
}
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
}
if (argc > optind) {
c.dbg_lv = 0;
err = EUNKNOWN_ARG;
}
if (err == NOERROR)
return;
/* print out error */
switch (err) {
case EWRONG_OPT:
MSG(0, "\tError: Wrong option -%c %s\n", option, optarg);
break;
case ENEED_ARG:
MSG(0, "\tError: Need argument for -%c\n", option);
break;
case EUNKNOWN_OPT:
MSG(0, "\tError: Unknown option %c\n", option);
break;
case EUNKNOWN_ARG:
MSG(0, "\tError: Unknown argument %s\n", argv[optind]);
break;
}
error_out(prog);
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
}
static void do_fsck(struct f2fs_sb_info *sbi)
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
{
struct f2fs_checkpoint *ckpt = F2FS_CKPT(sbi);
u32 flag = le32_to_cpu(ckpt->ckpt_flags);
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
u32 blk_cnt;
fsck_init(sbi);
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
print_cp_state(flag);
if (!c.fix_on && !c.bug_on) {
switch (c.preen_mode) {
case PREEN_MODE_1:
if (fsck_chk_meta(sbi)) {
MSG(0, "[FSCK] F2FS metadata [Fail]");
MSG(0, "\tError: meta does not match, "
"force check all\n");
} else {
MSG(0, "[FSCK] F2FS metadata [Ok..]");
fsck_free(sbi);
return;
}
if (!c.ro)
c.fix_on = 1;
break;
}
} else {
/*
* we can hit this in 3 situations:
* 1. fsck -f, fix_on has already been set to 1 when
* parsing options;
* 2. fsck -a && CP_FSCK_FLAG is set, fix_on has already
* been set to 1 when checking CP_FSCK_FLAG;
* 3. fsck -p 1 && error is detected, then bug_on is set,
* we set fix_on = 1 here, so that fsck can fix errors
* automatically
*/
c.fix_on = 1;
}
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
fsck_chk_orphan_node(sbi);
/* Traverse all block recursively from root inode */
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
blk_cnt = 1;
fsck_chk_node_blk(sbi, NULL, sbi->root_ino_num, (u8 *)"/",
F2FS_FT_DIR, TYPE_INODE, &blk_cnt, NULL);
fsck_verify(sbi);
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
fsck_free(sbi);
}
static void do_dump(struct f2fs_sb_info *sbi)
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
{
struct dump_option *opt = (struct dump_option *)c.private;
struct f2fs_checkpoint *ckpt = F2FS_CKPT(sbi);
u32 flag = le32_to_cpu(ckpt->ckpt_flags);
if (opt->end_nat == -1)
opt->end_nat = NM_I(sbi)->max_nid;
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
if (opt->end_sit == -1)
opt->end_sit = SM_I(sbi)->main_segments;
if (opt->end_ssa == -1)
opt->end_ssa = SM_I(sbi)->main_segments;
if (opt->start_nat != -1)
nat_dump(sbi);
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
if (opt->start_sit != -1)
sit_dump(sbi, opt->start_sit, opt->end_sit);
if (opt->start_ssa != -1)
ssa_dump(sbi, opt->start_ssa, opt->end_ssa);
if (opt->blk_addr != -1)
dump_info_from_blkaddr(sbi, opt->blk_addr);
if (opt->nid)
dump_node(sbi, opt->nid, 0);
print_cp_state(flag);
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
}
static int do_defrag(struct f2fs_sb_info *sbi)
{
struct f2fs_super_block *sb = F2FS_RAW_SUPER(sbi);
if (c.defrag_start > get_sb(block_count))
goto out_range;
if (c.defrag_start < SM_I(sbi)->main_blkaddr)
c.defrag_start = SM_I(sbi)->main_blkaddr;
if (c.defrag_len == 0)
c.defrag_len = sbi->blocks_per_seg;
if (c.defrag_start + c.defrag_len > get_sb(block_count))
c.defrag_len = get_sb(block_count) - c.defrag_start;
if (c.defrag_target == 0) {
c.defrag_target = c.defrag_start - 1;
if (!c.defrag_shrink)
c.defrag_target += c.defrag_len + 1;
}
if (c.defrag_target < SM_I(sbi)->main_blkaddr ||
c.defrag_target > get_sb(block_count))
goto out_range;
if (c.defrag_target >= c.defrag_start &&
c.defrag_target < c.defrag_start + c.defrag_len)
goto out_range;
if (c.defrag_start > c.defrag_target)
MSG(0, "Info: Move 0x%"PRIx64" <- [0x%"PRIx64"-0x%"PRIx64"]\n",
c.defrag_target,
c.defrag_start,
c.defrag_start + c.defrag_len - 1);
else
MSG(0, "Info: Move [0x%"PRIx64"-0x%"PRIx64"] -> 0x%"PRIx64"\n",
c.defrag_start,
c.defrag_start + c.defrag_len - 1,
c.defrag_target);
return f2fs_defragment(sbi, c.defrag_start, c.defrag_len,
c.defrag_target, c.defrag_shrink);
out_range:
ASSERT_MSG("Out-of-range [0x%"PRIx64" ~ 0x%"PRIx64"] to 0x%"PRIx64"",
c.defrag_start,
c.defrag_start + c.defrag_len - 1,
c.defrag_target);
return -1;
}
static int do_resize(struct f2fs_sb_info *sbi)
{
struct f2fs_super_block *sb = F2FS_RAW_SUPER(sbi);
if (!c.target_sectors)
c.target_sectors = c.total_sectors;
if (c.target_sectors > c.total_sectors) {
ASSERT_MSG("Out-of-range Target=0x%"PRIx64" / 0x%"PRIx64"",
c.target_sectors, c.total_sectors);
return -1;
}
/* may different sector size */
if ((c.target_sectors * c.sector_size >>
get_sb(log_blocksize)) <= get_sb(block_count)) {
ASSERT_MSG("Nothing to resize, now only support resize to expand\n");
return -1;
}
return f2fs_resize(sbi);
}
static int do_sload(struct f2fs_sb_info *sbi)
{
if (!c.from_dir) {
MSG(0, "\tError: Need source directory\n");
sload_usage();
return -1;
}
if (!c.mount_point)
c.mount_point = "/";
return f2fs_sload(sbi, c.from_dir, c.mount_point, NULL, NULL);
}
int main(int argc, char **argv)
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
{
struct f2fs_sb_info *sbi;
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
int ret = 0;
f2fs_init_configuration();
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
f2fs_parse_options(argc, argv);
if (f2fs_devs_are_umounted() < 0) {
if (!c.ro || c.func == DEFRAG) {
MSG(0, "\tError: Not available on mounted device!\n");
return -1;
}
/* allow ro-mounted partition */
MSG(0, "Info: Check FS only due to RO\n");
c.fix_on = 0;
c.auto_fix = 0;
}
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
/* Get device */
if (f2fs_get_device_info() < 0)
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
return -1;
fsck_again:
memset(&gfsck, 0, sizeof(gfsck));
gfsck.sbi.fsck = &gfsck;
sbi = &gfsck.sbi;
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
ret = f2fs_do_mount(sbi);
if (ret != 0) {
if (ret == 1) {
MSG(0, "Info: No error was reported\n");
ret = 0;
}
goto out_err;
}
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
switch (c.func) {
case FSCK:
do_fsck(sbi);
break;
case DUMP:
do_dump(sbi);
break;
#ifndef WITH_ANDROID
case DEFRAG:
ret = do_defrag(sbi);
if (ret)
goto out_err;
break;
case RESIZE:
if (do_resize(sbi))
goto out_err;
break;
case SLOAD:
do_sload(sbi);
break;
#endif
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
}
f2fs_do_umount(sbi);
if (c.func == FSCK && c.bug_on) {
if (!c.ro && c.fix_on == 0 && c.auto_fix == 0) {
char ans[255] = {0};
retry:
printf("Do you want to fix this partition? [Y/N] ");
ret = scanf("%s", ans);
ASSERT(ret >= 0);
if (!strcasecmp(ans, "y"))
c.fix_on = 1;
else if (!strcasecmp(ans, "n"))
c.fix_on = 0;
else
goto retry;
if (c.fix_on)
goto fsck_again;
}
}
f2fs_finalize_device();
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
printf("\nDone.\n");
return 0;
out_err:
if (sbi->ckpt)
free(sbi->ckpt);
if (sbi->raw_super)
free(sbi->raw_super);
return ret;
f2fs-tools: add fsck.f2fs and dump.f2fs fsck.f2fs checks file system consistency, but does not repair a broken file system yet. dump.f2fs shows the information of a specific inode and makes dump file of SSA and SIT. f2fs checks file system consistency as follows: o When data about used area and its metadata are identical, f2fs is considered consistent. To verify such consistency, we use three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap. First, each bit in nat_area_bitmap corresponds to a nid in NAT. Second, each bit in sit_area_bitmap corresponds to a valid block in a segment. This bitmap is same to the total valid_map of f2fs_sit_entries in SIT. Last, each bit in main_area_bitmap corresponds to a block in main area except meta area. After a consistency check of each block, we set or clear the corresponding bit of each bitmap. From the root node, we start consistency check. The verified information varies according to block type. 1. NODE - Read information of node block from NAT - Check if block address is allocated using node info. - Check if the type of f2fs_summary related to nid in SSA is NODE. - Update the corresponding bit in nat_area_bitmap. - Update the corresponding bit in sit_area_bitmap. - Set the corresponding bit in main_area_bitmap to 1. - Then, read node block. According to its attribute, explore inode/direct node/indirect node/double indirect node recursively. - If it is an inode block, we also check its xattr and hard link. 2. DATA - Check if the type of f2fs_summary related to nid in SSA is DATA. - Set the corresponding bits of sit_area_bitmap and main_area_bitmap to visited - If it is a dentry block, traverse each dentries that may be regular file or directory. At this time, it will check inode block again. Finally, we verify whether - every nat_area_bitmap is visited - any unreachable hard link exists - values of sit_area_bitmap and main_area_bitmap are identical - total_valid_block_count/node_count/inode_count are correct Usage: o fsck.f2fs # fsck.f2fs /dev/sdx options: -d debug level [default:0] o dump.f2fs # dump.f2fs -i [ino] /dev/sdx # dump.f2fs -s 0~-1 /dev/sdx (SIT dump) # dump.f2fs -a 0~-1 /dev/sdx (SSA dump) options: -d debug level [default:0] -i inode no (hex) -s [SIT dump segno from #1~#2 (decimal), for all 0~-1] -a [SSA dump segno from #1~#2 (decimal), for all 0~-1] Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs dump.f2fs Signed-off-by: Changman Lee <cm224.lee@samsung.com> Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com> Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
}