f2fs-tools: add fsck.f2fs and dump.f2fs
fsck.f2fs checks file system consistency, but does not repair a broken
file system yet.
dump.f2fs shows the information of a specific inode and makes dump file
of SSA and SIT.
f2fs checks file system consistency as follows:
o When data about used area and its metadata are identical,
f2fs is considered consistent. To verify such consistency, we use
three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap.
First, each bit in nat_area_bitmap corresponds to a nid in NAT.
Second, each bit in sit_area_bitmap corresponds to a valid block in a
segment. This bitmap is same to the total valid_map of f2fs_sit_entries
in SIT.
Last, each bit in main_area_bitmap corresponds to a block in main area
except meta area.
After a consistency check of each block, we set or clear the
corresponding bit of each bitmap.
From the root node, we start consistency check. The verified
information varies according to block type.
1. NODE
- Read information of node block from NAT
- Check if block address is allocated using node info.
- Check if the type of f2fs_summary related to nid in SSA is NODE.
- Update the corresponding bit in nat_area_bitmap.
- Update the corresponding bit in sit_area_bitmap.
- Set the corresponding bit in main_area_bitmap to 1.
- Then, read node block. According to its attribute, explore
inode/direct node/indirect node/double indirect node
recursively.
- If it is an inode block, we also check its xattr and hard link.
2. DATA
- Check if the type of f2fs_summary related to nid in SSA is DATA.
- Set the corresponding bits of sit_area_bitmap and
main_area_bitmap to visited
- If it is a dentry block, traverse each dentries that may be
regular
file or directory. At this time, it will check inode block again.
Finally, we verify whether
- every nat_area_bitmap is visited
- any unreachable hard link exists
- values of sit_area_bitmap and main_area_bitmap are identical
- total_valid_block_count/node_count/inode_count are correct
Usage:
o fsck.f2fs
# fsck.f2fs /dev/sdx
options:
-d debug level [default:0]
o dump.f2fs
# dump.f2fs -i [ino] /dev/sdx
# dump.f2fs -s 0~-1 /dev/sdx (SIT dump)
# dump.f2fs -a 0~-1 /dev/sdx (SSA dump)
options:
-d debug level [default:0]
-i inode no (hex)
-s [SIT dump segno from #1~#2 (decimal), for all 0~-1]
-a [SSA dump segno from #1~#2 (decimal), for all 0~-1]
Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs
dump.f2fs
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
|
|
|
/**
|
|
|
|
* main.c
|
|
|
|
*
|
|
|
|
* Copyright (c) 2013 Samsung Electronics Co., Ltd.
|
|
|
|
* http://www.samsung.com/
|
2015-10-23 18:45:36 +00:00
|
|
|
* Copyright (c) 2015 Jaegeuk Kim <jaegeuk@kernel.org>
|
|
|
|
* : implement defrag.f2fs
|
f2fs-tools: add fsck.f2fs and dump.f2fs
fsck.f2fs checks file system consistency, but does not repair a broken
file system yet.
dump.f2fs shows the information of a specific inode and makes dump file
of SSA and SIT.
f2fs checks file system consistency as follows:
o When data about used area and its metadata are identical,
f2fs is considered consistent. To verify such consistency, we use
three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap.
First, each bit in nat_area_bitmap corresponds to a nid in NAT.
Second, each bit in sit_area_bitmap corresponds to a valid block in a
segment. This bitmap is same to the total valid_map of f2fs_sit_entries
in SIT.
Last, each bit in main_area_bitmap corresponds to a block in main area
except meta area.
After a consistency check of each block, we set or clear the
corresponding bit of each bitmap.
From the root node, we start consistency check. The verified
information varies according to block type.
1. NODE
- Read information of node block from NAT
- Check if block address is allocated using node info.
- Check if the type of f2fs_summary related to nid in SSA is NODE.
- Update the corresponding bit in nat_area_bitmap.
- Update the corresponding bit in sit_area_bitmap.
- Set the corresponding bit in main_area_bitmap to 1.
- Then, read node block. According to its attribute, explore
inode/direct node/indirect node/double indirect node
recursively.
- If it is an inode block, we also check its xattr and hard link.
2. DATA
- Check if the type of f2fs_summary related to nid in SSA is DATA.
- Set the corresponding bits of sit_area_bitmap and
main_area_bitmap to visited
- If it is a dentry block, traverse each dentries that may be
regular
file or directory. At this time, it will check inode block again.
Finally, we verify whether
- every nat_area_bitmap is visited
- any unreachable hard link exists
- values of sit_area_bitmap and main_area_bitmap are identical
- total_valid_block_count/node_count/inode_count are correct
Usage:
o fsck.f2fs
# fsck.f2fs /dev/sdx
options:
-d debug level [default:0]
o dump.f2fs
# dump.f2fs -i [ino] /dev/sdx
# dump.f2fs -s 0~-1 /dev/sdx (SIT dump)
# dump.f2fs -a 0~-1 /dev/sdx (SSA dump)
options:
-d debug level [default:0]
-i inode no (hex)
-s [SIT dump segno from #1~#2 (decimal), for all 0~-1]
-a [SSA dump segno from #1~#2 (decimal), for all 0~-1]
Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs
dump.f2fs
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
|
|
|
*
|
|
|
|
* This program is free software; you can redistribute it and/or modify
|
|
|
|
* it under the terms of the GNU General Public License version 2 as
|
|
|
|
* published by the Free Software Foundation.
|
|
|
|
*/
|
|
|
|
#include "fsck.h"
|
|
|
|
#include <libgen.h>
|
|
|
|
|
2014-08-27 00:26:01 +00:00
|
|
|
struct f2fs_fsck gfsck;
|
f2fs-tools: add fsck.f2fs and dump.f2fs
fsck.f2fs checks file system consistency, but does not repair a broken
file system yet.
dump.f2fs shows the information of a specific inode and makes dump file
of SSA and SIT.
f2fs checks file system consistency as follows:
o When data about used area and its metadata are identical,
f2fs is considered consistent. To verify such consistency, we use
three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap.
First, each bit in nat_area_bitmap corresponds to a nid in NAT.
Second, each bit in sit_area_bitmap corresponds to a valid block in a
segment. This bitmap is same to the total valid_map of f2fs_sit_entries
in SIT.
Last, each bit in main_area_bitmap corresponds to a block in main area
except meta area.
After a consistency check of each block, we set or clear the
corresponding bit of each bitmap.
From the root node, we start consistency check. The verified
information varies according to block type.
1. NODE
- Read information of node block from NAT
- Check if block address is allocated using node info.
- Check if the type of f2fs_summary related to nid in SSA is NODE.
- Update the corresponding bit in nat_area_bitmap.
- Update the corresponding bit in sit_area_bitmap.
- Set the corresponding bit in main_area_bitmap to 1.
- Then, read node block. According to its attribute, explore
inode/direct node/indirect node/double indirect node
recursively.
- If it is an inode block, we also check its xattr and hard link.
2. DATA
- Check if the type of f2fs_summary related to nid in SSA is DATA.
- Set the corresponding bits of sit_area_bitmap and
main_area_bitmap to visited
- If it is a dentry block, traverse each dentries that may be
regular
file or directory. At this time, it will check inode block again.
Finally, we verify whether
- every nat_area_bitmap is visited
- any unreachable hard link exists
- values of sit_area_bitmap and main_area_bitmap are identical
- total_valid_block_count/node_count/inode_count are correct
Usage:
o fsck.f2fs
# fsck.f2fs /dev/sdx
options:
-d debug level [default:0]
o dump.f2fs
# dump.f2fs -i [ino] /dev/sdx
# dump.f2fs -s 0~-1 /dev/sdx (SIT dump)
# dump.f2fs -a 0~-1 /dev/sdx (SSA dump)
options:
-d debug level [default:0]
-i inode no (hex)
-s [SIT dump segno from #1~#2 (decimal), for all 0~-1]
-a [SSA dump segno from #1~#2 (decimal), for all 0~-1]
Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs
dump.f2fs
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
|
|
|
|
|
|
|
void fsck_usage()
|
|
|
|
{
|
|
|
|
MSG(0, "\nUsage: fsck.f2fs [options] device\n");
|
|
|
|
MSG(0, "[options]:\n");
|
2014-09-04 02:41:44 +00:00
|
|
|
MSG(0, " -a check/fix potential corruption, reported by f2fs\n");
|
f2fs-tools: add fsck.f2fs and dump.f2fs
fsck.f2fs checks file system consistency, but does not repair a broken
file system yet.
dump.f2fs shows the information of a specific inode and makes dump file
of SSA and SIT.
f2fs checks file system consistency as follows:
o When data about used area and its metadata are identical,
f2fs is considered consistent. To verify such consistency, we use
three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap.
First, each bit in nat_area_bitmap corresponds to a nid in NAT.
Second, each bit in sit_area_bitmap corresponds to a valid block in a
segment. This bitmap is same to the total valid_map of f2fs_sit_entries
in SIT.
Last, each bit in main_area_bitmap corresponds to a block in main area
except meta area.
After a consistency check of each block, we set or clear the
corresponding bit of each bitmap.
From the root node, we start consistency check. The verified
information varies according to block type.
1. NODE
- Read information of node block from NAT
- Check if block address is allocated using node info.
- Check if the type of f2fs_summary related to nid in SSA is NODE.
- Update the corresponding bit in nat_area_bitmap.
- Update the corresponding bit in sit_area_bitmap.
- Set the corresponding bit in main_area_bitmap to 1.
- Then, read node block. According to its attribute, explore
inode/direct node/indirect node/double indirect node
recursively.
- If it is an inode block, we also check its xattr and hard link.
2. DATA
- Check if the type of f2fs_summary related to nid in SSA is DATA.
- Set the corresponding bits of sit_area_bitmap and
main_area_bitmap to visited
- If it is a dentry block, traverse each dentries that may be
regular
file or directory. At this time, it will check inode block again.
Finally, we verify whether
- every nat_area_bitmap is visited
- any unreachable hard link exists
- values of sit_area_bitmap and main_area_bitmap are identical
- total_valid_block_count/node_count/inode_count are correct
Usage:
o fsck.f2fs
# fsck.f2fs /dev/sdx
options:
-d debug level [default:0]
o dump.f2fs
# dump.f2fs -i [ino] /dev/sdx
# dump.f2fs -s 0~-1 /dev/sdx (SIT dump)
# dump.f2fs -a 0~-1 /dev/sdx (SSA dump)
options:
-d debug level [default:0]
-i inode no (hex)
-s [SIT dump segno from #1~#2 (decimal), for all 0~-1]
-a [SSA dump segno from #1~#2 (decimal), for all 0~-1]
Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs
dump.f2fs
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
|
|
|
MSG(0, " -d debug level [default:0]\n");
|
2014-09-04 02:41:44 +00:00
|
|
|
MSG(0, " -f check/fix entire partition\n");
|
2015-10-23 21:03:29 +00:00
|
|
|
MSG(0, " -p preen mode [default is same as -a]\n");
|
2014-09-04 02:41:44 +00:00
|
|
|
MSG(0, " -t show directory tree [-d -1]\n");
|
f2fs-tools: add fsck.f2fs and dump.f2fs
fsck.f2fs checks file system consistency, but does not repair a broken
file system yet.
dump.f2fs shows the information of a specific inode and makes dump file
of SSA and SIT.
f2fs checks file system consistency as follows:
o When data about used area and its metadata are identical,
f2fs is considered consistent. To verify such consistency, we use
three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap.
First, each bit in nat_area_bitmap corresponds to a nid in NAT.
Second, each bit in sit_area_bitmap corresponds to a valid block in a
segment. This bitmap is same to the total valid_map of f2fs_sit_entries
in SIT.
Last, each bit in main_area_bitmap corresponds to a block in main area
except meta area.
After a consistency check of each block, we set or clear the
corresponding bit of each bitmap.
From the root node, we start consistency check. The verified
information varies according to block type.
1. NODE
- Read information of node block from NAT
- Check if block address is allocated using node info.
- Check if the type of f2fs_summary related to nid in SSA is NODE.
- Update the corresponding bit in nat_area_bitmap.
- Update the corresponding bit in sit_area_bitmap.
- Set the corresponding bit in main_area_bitmap to 1.
- Then, read node block. According to its attribute, explore
inode/direct node/indirect node/double indirect node
recursively.
- If it is an inode block, we also check its xattr and hard link.
2. DATA
- Check if the type of f2fs_summary related to nid in SSA is DATA.
- Set the corresponding bits of sit_area_bitmap and
main_area_bitmap to visited
- If it is a dentry block, traverse each dentries that may be
regular
file or directory. At this time, it will check inode block again.
Finally, we verify whether
- every nat_area_bitmap is visited
- any unreachable hard link exists
- values of sit_area_bitmap and main_area_bitmap are identical
- total_valid_block_count/node_count/inode_count are correct
Usage:
o fsck.f2fs
# fsck.f2fs /dev/sdx
options:
-d debug level [default:0]
o dump.f2fs
# dump.f2fs -i [ino] /dev/sdx
# dump.f2fs -s 0~-1 /dev/sdx (SIT dump)
# dump.f2fs -a 0~-1 /dev/sdx (SSA dump)
options:
-d debug level [default:0]
-i inode no (hex)
-s [SIT dump segno from #1~#2 (decimal), for all 0~-1]
-a [SSA dump segno from #1~#2 (decimal), for all 0~-1]
Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs
dump.f2fs
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
|
|
|
exit(1);
|
|
|
|
}
|
|
|
|
|
|
|
|
void dump_usage()
|
|
|
|
{
|
|
|
|
MSG(0, "\nUsage: dump.f2fs [options] device\n");
|
|
|
|
MSG(0, "[options]:\n");
|
|
|
|
MSG(0, " -d debug level [default:0]\n");
|
|
|
|
MSG(0, " -i inode no (hex)\n");
|
|
|
|
MSG(0, " -s [SIT dump segno from #1~#2 (decimal), for all 0~-1]\n");
|
|
|
|
MSG(0, " -a [SSA dump segno from #1~#2 (decimal), for all 0~-1]\n");
|
2013-07-18 02:20:05 +00:00
|
|
|
MSG(0, " -b blk_addr (in 4KB)\n");
|
f2fs-tools: add fsck.f2fs and dump.f2fs
fsck.f2fs checks file system consistency, but does not repair a broken
file system yet.
dump.f2fs shows the information of a specific inode and makes dump file
of SSA and SIT.
f2fs checks file system consistency as follows:
o When data about used area and its metadata are identical,
f2fs is considered consistent. To verify such consistency, we use
three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap.
First, each bit in nat_area_bitmap corresponds to a nid in NAT.
Second, each bit in sit_area_bitmap corresponds to a valid block in a
segment. This bitmap is same to the total valid_map of f2fs_sit_entries
in SIT.
Last, each bit in main_area_bitmap corresponds to a block in main area
except meta area.
After a consistency check of each block, we set or clear the
corresponding bit of each bitmap.
From the root node, we start consistency check. The verified
information varies according to block type.
1. NODE
- Read information of node block from NAT
- Check if block address is allocated using node info.
- Check if the type of f2fs_summary related to nid in SSA is NODE.
- Update the corresponding bit in nat_area_bitmap.
- Update the corresponding bit in sit_area_bitmap.
- Set the corresponding bit in main_area_bitmap to 1.
- Then, read node block. According to its attribute, explore
inode/direct node/indirect node/double indirect node
recursively.
- If it is an inode block, we also check its xattr and hard link.
2. DATA
- Check if the type of f2fs_summary related to nid in SSA is DATA.
- Set the corresponding bits of sit_area_bitmap and
main_area_bitmap to visited
- If it is a dentry block, traverse each dentries that may be
regular
file or directory. At this time, it will check inode block again.
Finally, we verify whether
- every nat_area_bitmap is visited
- any unreachable hard link exists
- values of sit_area_bitmap and main_area_bitmap are identical
- total_valid_block_count/node_count/inode_count are correct
Usage:
o fsck.f2fs
# fsck.f2fs /dev/sdx
options:
-d debug level [default:0]
o dump.f2fs
# dump.f2fs -i [ino] /dev/sdx
# dump.f2fs -s 0~-1 /dev/sdx (SIT dump)
# dump.f2fs -a 0~-1 /dev/sdx (SSA dump)
options:
-d debug level [default:0]
-i inode no (hex)
-s [SIT dump segno from #1~#2 (decimal), for all 0~-1]
-a [SSA dump segno from #1~#2 (decimal), for all 0~-1]
Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs
dump.f2fs
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
|
|
|
|
|
|
|
exit(1);
|
|
|
|
}
|
|
|
|
|
2015-10-23 18:45:36 +00:00
|
|
|
void defrag_usage()
|
|
|
|
{
|
|
|
|
MSG(0, "\nUsage: defrag.f2fs [options] device\n");
|
|
|
|
MSG(0, "[options]:\n");
|
|
|
|
MSG(0, " -d debug level [default:0]\n");
|
|
|
|
MSG(0, " -s start block address [default: main_blkaddr]\n");
|
|
|
|
MSG(0, " -l length [default:512 (2MB)]\n");
|
|
|
|
MSG(0, " -t target block address [default: main_blkaddr + 2MB]\n");
|
|
|
|
MSG(0, " -i set direction as shrink [default: expand]\n");
|
|
|
|
exit(1);
|
|
|
|
}
|
|
|
|
|
f2fs-tools: add fsck.f2fs and dump.f2fs
fsck.f2fs checks file system consistency, but does not repair a broken
file system yet.
dump.f2fs shows the information of a specific inode and makes dump file
of SSA and SIT.
f2fs checks file system consistency as follows:
o When data about used area and its metadata are identical,
f2fs is considered consistent. To verify such consistency, we use
three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap.
First, each bit in nat_area_bitmap corresponds to a nid in NAT.
Second, each bit in sit_area_bitmap corresponds to a valid block in a
segment. This bitmap is same to the total valid_map of f2fs_sit_entries
in SIT.
Last, each bit in main_area_bitmap corresponds to a block in main area
except meta area.
After a consistency check of each block, we set or clear the
corresponding bit of each bitmap.
From the root node, we start consistency check. The verified
information varies according to block type.
1. NODE
- Read information of node block from NAT
- Check if block address is allocated using node info.
- Check if the type of f2fs_summary related to nid in SSA is NODE.
- Update the corresponding bit in nat_area_bitmap.
- Update the corresponding bit in sit_area_bitmap.
- Set the corresponding bit in main_area_bitmap to 1.
- Then, read node block. According to its attribute, explore
inode/direct node/indirect node/double indirect node
recursively.
- If it is an inode block, we also check its xattr and hard link.
2. DATA
- Check if the type of f2fs_summary related to nid in SSA is DATA.
- Set the corresponding bits of sit_area_bitmap and
main_area_bitmap to visited
- If it is a dentry block, traverse each dentries that may be
regular
file or directory. At this time, it will check inode block again.
Finally, we verify whether
- every nat_area_bitmap is visited
- any unreachable hard link exists
- values of sit_area_bitmap and main_area_bitmap are identical
- total_valid_block_count/node_count/inode_count are correct
Usage:
o fsck.f2fs
# fsck.f2fs /dev/sdx
options:
-d debug level [default:0]
o dump.f2fs
# dump.f2fs -i [ino] /dev/sdx
# dump.f2fs -s 0~-1 /dev/sdx (SIT dump)
# dump.f2fs -a 0~-1 /dev/sdx (SSA dump)
options:
-d debug level [default:0]
-i inode no (hex)
-s [SIT dump segno from #1~#2 (decimal), for all 0~-1]
-a [SSA dump segno from #1~#2 (decimal), for all 0~-1]
Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs
dump.f2fs
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
|
|
|
void f2fs_parse_options(int argc, char *argv[])
|
|
|
|
{
|
|
|
|
int option = 0;
|
|
|
|
char *prog = basename(argv[0]);
|
|
|
|
|
|
|
|
if (!strcmp("fsck.f2fs", prog)) {
|
2015-10-23 21:03:29 +00:00
|
|
|
const char *option_string = "ad:fpt";
|
f2fs-tools: add fsck.f2fs and dump.f2fs
fsck.f2fs checks file system consistency, but does not repair a broken
file system yet.
dump.f2fs shows the information of a specific inode and makes dump file
of SSA and SIT.
f2fs checks file system consistency as follows:
o When data about used area and its metadata are identical,
f2fs is considered consistent. To verify such consistency, we use
three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap.
First, each bit in nat_area_bitmap corresponds to a nid in NAT.
Second, each bit in sit_area_bitmap corresponds to a valid block in a
segment. This bitmap is same to the total valid_map of f2fs_sit_entries
in SIT.
Last, each bit in main_area_bitmap corresponds to a block in main area
except meta area.
After a consistency check of each block, we set or clear the
corresponding bit of each bitmap.
From the root node, we start consistency check. The verified
information varies according to block type.
1. NODE
- Read information of node block from NAT
- Check if block address is allocated using node info.
- Check if the type of f2fs_summary related to nid in SSA is NODE.
- Update the corresponding bit in nat_area_bitmap.
- Update the corresponding bit in sit_area_bitmap.
- Set the corresponding bit in main_area_bitmap to 1.
- Then, read node block. According to its attribute, explore
inode/direct node/indirect node/double indirect node
recursively.
- If it is an inode block, we also check its xattr and hard link.
2. DATA
- Check if the type of f2fs_summary related to nid in SSA is DATA.
- Set the corresponding bits of sit_area_bitmap and
main_area_bitmap to visited
- If it is a dentry block, traverse each dentries that may be
regular
file or directory. At this time, it will check inode block again.
Finally, we verify whether
- every nat_area_bitmap is visited
- any unreachable hard link exists
- values of sit_area_bitmap and main_area_bitmap are identical
- total_valid_block_count/node_count/inode_count are correct
Usage:
o fsck.f2fs
# fsck.f2fs /dev/sdx
options:
-d debug level [default:0]
o dump.f2fs
# dump.f2fs -i [ino] /dev/sdx
# dump.f2fs -s 0~-1 /dev/sdx (SIT dump)
# dump.f2fs -a 0~-1 /dev/sdx (SSA dump)
options:
-d debug level [default:0]
-i inode no (hex)
-s [SIT dump segno from #1~#2 (decimal), for all 0~-1]
-a [SSA dump segno from #1~#2 (decimal), for all 0~-1]
Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs
dump.f2fs
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
|
|
|
|
|
|
|
config.func = FSCK;
|
|
|
|
while ((option = getopt(argc, argv, option_string)) != EOF) {
|
|
|
|
switch (option) {
|
2014-09-03 01:07:35 +00:00
|
|
|
case 'a':
|
2015-10-23 21:03:29 +00:00
|
|
|
case 'p':
|
2014-09-03 01:07:35 +00:00
|
|
|
config.auto_fix = 1;
|
|
|
|
MSG(0, "Info: Fix the reported corruption.\n");
|
|
|
|
break;
|
2014-08-27 00:26:01 +00:00
|
|
|
case 'd':
|
|
|
|
config.dbg_lv = atoi(optarg);
|
|
|
|
MSG(0, "Info: Debug level = %d\n",
|
|
|
|
config.dbg_lv);
|
|
|
|
break;
|
|
|
|
case 'f':
|
|
|
|
config.fix_on = 1;
|
|
|
|
MSG(0, "Info: Force to fix corruption\n");
|
|
|
|
break;
|
2014-09-03 01:07:35 +00:00
|
|
|
case 't':
|
|
|
|
config.dbg_lv = -1;
|
|
|
|
break;
|
2014-08-27 00:26:01 +00:00
|
|
|
default:
|
|
|
|
MSG(0, "\tError: Unknown option %c\n", option);
|
|
|
|
fsck_usage();
|
|
|
|
break;
|
f2fs-tools: add fsck.f2fs and dump.f2fs
fsck.f2fs checks file system consistency, but does not repair a broken
file system yet.
dump.f2fs shows the information of a specific inode and makes dump file
of SSA and SIT.
f2fs checks file system consistency as follows:
o When data about used area and its metadata are identical,
f2fs is considered consistent. To verify such consistency, we use
three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap.
First, each bit in nat_area_bitmap corresponds to a nid in NAT.
Second, each bit in sit_area_bitmap corresponds to a valid block in a
segment. This bitmap is same to the total valid_map of f2fs_sit_entries
in SIT.
Last, each bit in main_area_bitmap corresponds to a block in main area
except meta area.
After a consistency check of each block, we set or clear the
corresponding bit of each bitmap.
From the root node, we start consistency check. The verified
information varies according to block type.
1. NODE
- Read information of node block from NAT
- Check if block address is allocated using node info.
- Check if the type of f2fs_summary related to nid in SSA is NODE.
- Update the corresponding bit in nat_area_bitmap.
- Update the corresponding bit in sit_area_bitmap.
- Set the corresponding bit in main_area_bitmap to 1.
- Then, read node block. According to its attribute, explore
inode/direct node/indirect node/double indirect node
recursively.
- If it is an inode block, we also check its xattr and hard link.
2. DATA
- Check if the type of f2fs_summary related to nid in SSA is DATA.
- Set the corresponding bits of sit_area_bitmap and
main_area_bitmap to visited
- If it is a dentry block, traverse each dentries that may be
regular
file or directory. At this time, it will check inode block again.
Finally, we verify whether
- every nat_area_bitmap is visited
- any unreachable hard link exists
- values of sit_area_bitmap and main_area_bitmap are identical
- total_valid_block_count/node_count/inode_count are correct
Usage:
o fsck.f2fs
# fsck.f2fs /dev/sdx
options:
-d debug level [default:0]
o dump.f2fs
# dump.f2fs -i [ino] /dev/sdx
# dump.f2fs -s 0~-1 /dev/sdx (SIT dump)
# dump.f2fs -a 0~-1 /dev/sdx (SSA dump)
options:
-d debug level [default:0]
-i inode no (hex)
-s [SIT dump segno from #1~#2 (decimal), for all 0~-1]
-a [SSA dump segno from #1~#2 (decimal), for all 0~-1]
Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs
dump.f2fs
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
|
|
|
}
|
|
|
|
}
|
|
|
|
} else if (!strcmp("dump.f2fs", prog)) {
|
2013-07-18 02:20:05 +00:00
|
|
|
const char *option_string = "d:i:s:a:b:";
|
f2fs-tools: add fsck.f2fs and dump.f2fs
fsck.f2fs checks file system consistency, but does not repair a broken
file system yet.
dump.f2fs shows the information of a specific inode and makes dump file
of SSA and SIT.
f2fs checks file system consistency as follows:
o When data about used area and its metadata are identical,
f2fs is considered consistent. To verify such consistency, we use
three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap.
First, each bit in nat_area_bitmap corresponds to a nid in NAT.
Second, each bit in sit_area_bitmap corresponds to a valid block in a
segment. This bitmap is same to the total valid_map of f2fs_sit_entries
in SIT.
Last, each bit in main_area_bitmap corresponds to a block in main area
except meta area.
After a consistency check of each block, we set or clear the
corresponding bit of each bitmap.
From the root node, we start consistency check. The verified
information varies according to block type.
1. NODE
- Read information of node block from NAT
- Check if block address is allocated using node info.
- Check if the type of f2fs_summary related to nid in SSA is NODE.
- Update the corresponding bit in nat_area_bitmap.
- Update the corresponding bit in sit_area_bitmap.
- Set the corresponding bit in main_area_bitmap to 1.
- Then, read node block. According to its attribute, explore
inode/direct node/indirect node/double indirect node
recursively.
- If it is an inode block, we also check its xattr and hard link.
2. DATA
- Check if the type of f2fs_summary related to nid in SSA is DATA.
- Set the corresponding bits of sit_area_bitmap and
main_area_bitmap to visited
- If it is a dentry block, traverse each dentries that may be
regular
file or directory. At this time, it will check inode block again.
Finally, we verify whether
- every nat_area_bitmap is visited
- any unreachable hard link exists
- values of sit_area_bitmap and main_area_bitmap are identical
- total_valid_block_count/node_count/inode_count are correct
Usage:
o fsck.f2fs
# fsck.f2fs /dev/sdx
options:
-d debug level [default:0]
o dump.f2fs
# dump.f2fs -i [ino] /dev/sdx
# dump.f2fs -s 0~-1 /dev/sdx (SIT dump)
# dump.f2fs -a 0~-1 /dev/sdx (SSA dump)
options:
-d debug level [default:0]
-i inode no (hex)
-s [SIT dump segno from #1~#2 (decimal), for all 0~-1]
-a [SSA dump segno from #1~#2 (decimal), for all 0~-1]
Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs
dump.f2fs
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
|
|
|
static struct dump_option dump_opt = {
|
|
|
|
.nid = 3, /* default root ino */
|
|
|
|
.start_sit = -1,
|
|
|
|
.end_sit = -1,
|
|
|
|
.start_ssa = -1,
|
|
|
|
.end_ssa = -1,
|
2013-07-18 02:20:05 +00:00
|
|
|
.blk_addr = -1,
|
f2fs-tools: add fsck.f2fs and dump.f2fs
fsck.f2fs checks file system consistency, but does not repair a broken
file system yet.
dump.f2fs shows the information of a specific inode and makes dump file
of SSA and SIT.
f2fs checks file system consistency as follows:
o When data about used area and its metadata are identical,
f2fs is considered consistent. To verify such consistency, we use
three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap.
First, each bit in nat_area_bitmap corresponds to a nid in NAT.
Second, each bit in sit_area_bitmap corresponds to a valid block in a
segment. This bitmap is same to the total valid_map of f2fs_sit_entries
in SIT.
Last, each bit in main_area_bitmap corresponds to a block in main area
except meta area.
After a consistency check of each block, we set or clear the
corresponding bit of each bitmap.
From the root node, we start consistency check. The verified
information varies according to block type.
1. NODE
- Read information of node block from NAT
- Check if block address is allocated using node info.
- Check if the type of f2fs_summary related to nid in SSA is NODE.
- Update the corresponding bit in nat_area_bitmap.
- Update the corresponding bit in sit_area_bitmap.
- Set the corresponding bit in main_area_bitmap to 1.
- Then, read node block. According to its attribute, explore
inode/direct node/indirect node/double indirect node
recursively.
- If it is an inode block, we also check its xattr and hard link.
2. DATA
- Check if the type of f2fs_summary related to nid in SSA is DATA.
- Set the corresponding bits of sit_area_bitmap and
main_area_bitmap to visited
- If it is a dentry block, traverse each dentries that may be
regular
file or directory. At this time, it will check inode block again.
Finally, we verify whether
- every nat_area_bitmap is visited
- any unreachable hard link exists
- values of sit_area_bitmap and main_area_bitmap are identical
- total_valid_block_count/node_count/inode_count are correct
Usage:
o fsck.f2fs
# fsck.f2fs /dev/sdx
options:
-d debug level [default:0]
o dump.f2fs
# dump.f2fs -i [ino] /dev/sdx
# dump.f2fs -s 0~-1 /dev/sdx (SIT dump)
# dump.f2fs -a 0~-1 /dev/sdx (SSA dump)
options:
-d debug level [default:0]
-i inode no (hex)
-s [SIT dump segno from #1~#2 (decimal), for all 0~-1]
-a [SSA dump segno from #1~#2 (decimal), for all 0~-1]
Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs
dump.f2fs
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
|
|
|
};
|
|
|
|
|
|
|
|
config.func = DUMP;
|
|
|
|
while ((option = getopt(argc, argv, option_string)) != EOF) {
|
2014-08-27 00:26:01 +00:00
|
|
|
int ret = 0;
|
|
|
|
|
f2fs-tools: add fsck.f2fs and dump.f2fs
fsck.f2fs checks file system consistency, but does not repair a broken
file system yet.
dump.f2fs shows the information of a specific inode and makes dump file
of SSA and SIT.
f2fs checks file system consistency as follows:
o When data about used area and its metadata are identical,
f2fs is considered consistent. To verify such consistency, we use
three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap.
First, each bit in nat_area_bitmap corresponds to a nid in NAT.
Second, each bit in sit_area_bitmap corresponds to a valid block in a
segment. This bitmap is same to the total valid_map of f2fs_sit_entries
in SIT.
Last, each bit in main_area_bitmap corresponds to a block in main area
except meta area.
After a consistency check of each block, we set or clear the
corresponding bit of each bitmap.
From the root node, we start consistency check. The verified
information varies according to block type.
1. NODE
- Read information of node block from NAT
- Check if block address is allocated using node info.
- Check if the type of f2fs_summary related to nid in SSA is NODE.
- Update the corresponding bit in nat_area_bitmap.
- Update the corresponding bit in sit_area_bitmap.
- Set the corresponding bit in main_area_bitmap to 1.
- Then, read node block. According to its attribute, explore
inode/direct node/indirect node/double indirect node
recursively.
- If it is an inode block, we also check its xattr and hard link.
2. DATA
- Check if the type of f2fs_summary related to nid in SSA is DATA.
- Set the corresponding bits of sit_area_bitmap and
main_area_bitmap to visited
- If it is a dentry block, traverse each dentries that may be
regular
file or directory. At this time, it will check inode block again.
Finally, we verify whether
- every nat_area_bitmap is visited
- any unreachable hard link exists
- values of sit_area_bitmap and main_area_bitmap are identical
- total_valid_block_count/node_count/inode_count are correct
Usage:
o fsck.f2fs
# fsck.f2fs /dev/sdx
options:
-d debug level [default:0]
o dump.f2fs
# dump.f2fs -i [ino] /dev/sdx
# dump.f2fs -s 0~-1 /dev/sdx (SIT dump)
# dump.f2fs -a 0~-1 /dev/sdx (SSA dump)
options:
-d debug level [default:0]
-i inode no (hex)
-s [SIT dump segno from #1~#2 (decimal), for all 0~-1]
-a [SSA dump segno from #1~#2 (decimal), for all 0~-1]
Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs
dump.f2fs
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
|
|
|
switch (option) {
|
2014-08-27 00:26:01 +00:00
|
|
|
case 'd':
|
|
|
|
config.dbg_lv = atoi(optarg);
|
|
|
|
MSG(0, "Info: Debug level = %d\n",
|
|
|
|
config.dbg_lv);
|
|
|
|
break;
|
|
|
|
case 'i':
|
|
|
|
if (strncmp(optarg, "0x", 2))
|
|
|
|
ret = sscanf(optarg, "%d",
|
|
|
|
&dump_opt.nid);
|
|
|
|
else
|
|
|
|
ret = sscanf(optarg, "%x",
|
|
|
|
&dump_opt.nid);
|
|
|
|
break;
|
|
|
|
case 's':
|
|
|
|
ret = sscanf(optarg, "%d~%d",
|
|
|
|
&dump_opt.start_sit,
|
|
|
|
&dump_opt.end_sit);
|
|
|
|
break;
|
|
|
|
case 'a':
|
|
|
|
ret = sscanf(optarg, "%d~%d",
|
|
|
|
&dump_opt.start_ssa,
|
|
|
|
&dump_opt.end_ssa);
|
|
|
|
break;
|
|
|
|
case 'b':
|
|
|
|
if (strncmp(optarg, "0x", 2))
|
|
|
|
ret = sscanf(optarg, "%d",
|
|
|
|
&dump_opt.blk_addr);
|
|
|
|
else
|
|
|
|
ret = sscanf(optarg, "%x",
|
|
|
|
&dump_opt.blk_addr);
|
|
|
|
break;
|
|
|
|
default:
|
|
|
|
MSG(0, "\tError: Unknown option %c\n", option);
|
|
|
|
dump_usage();
|
|
|
|
break;
|
f2fs-tools: add fsck.f2fs and dump.f2fs
fsck.f2fs checks file system consistency, but does not repair a broken
file system yet.
dump.f2fs shows the information of a specific inode and makes dump file
of SSA and SIT.
f2fs checks file system consistency as follows:
o When data about used area and its metadata are identical,
f2fs is considered consistent. To verify such consistency, we use
three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap.
First, each bit in nat_area_bitmap corresponds to a nid in NAT.
Second, each bit in sit_area_bitmap corresponds to a valid block in a
segment. This bitmap is same to the total valid_map of f2fs_sit_entries
in SIT.
Last, each bit in main_area_bitmap corresponds to a block in main area
except meta area.
After a consistency check of each block, we set or clear the
corresponding bit of each bitmap.
From the root node, we start consistency check. The verified
information varies according to block type.
1. NODE
- Read information of node block from NAT
- Check if block address is allocated using node info.
- Check if the type of f2fs_summary related to nid in SSA is NODE.
- Update the corresponding bit in nat_area_bitmap.
- Update the corresponding bit in sit_area_bitmap.
- Set the corresponding bit in main_area_bitmap to 1.
- Then, read node block. According to its attribute, explore
inode/direct node/indirect node/double indirect node
recursively.
- If it is an inode block, we also check its xattr and hard link.
2. DATA
- Check if the type of f2fs_summary related to nid in SSA is DATA.
- Set the corresponding bits of sit_area_bitmap and
main_area_bitmap to visited
- If it is a dentry block, traverse each dentries that may be
regular
file or directory. At this time, it will check inode block again.
Finally, we verify whether
- every nat_area_bitmap is visited
- any unreachable hard link exists
- values of sit_area_bitmap and main_area_bitmap are identical
- total_valid_block_count/node_count/inode_count are correct
Usage:
o fsck.f2fs
# fsck.f2fs /dev/sdx
options:
-d debug level [default:0]
o dump.f2fs
# dump.f2fs -i [ino] /dev/sdx
# dump.f2fs -s 0~-1 /dev/sdx (SIT dump)
# dump.f2fs -a 0~-1 /dev/sdx (SSA dump)
options:
-d debug level [default:0]
-i inode no (hex)
-s [SIT dump segno from #1~#2 (decimal), for all 0~-1]
-a [SSA dump segno from #1~#2 (decimal), for all 0~-1]
Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs
dump.f2fs
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
|
|
|
}
|
2014-08-27 00:26:01 +00:00
|
|
|
ASSERT(ret >= 0);
|
f2fs-tools: add fsck.f2fs and dump.f2fs
fsck.f2fs checks file system consistency, but does not repair a broken
file system yet.
dump.f2fs shows the information of a specific inode and makes dump file
of SSA and SIT.
f2fs checks file system consistency as follows:
o When data about used area and its metadata are identical,
f2fs is considered consistent. To verify such consistency, we use
three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap.
First, each bit in nat_area_bitmap corresponds to a nid in NAT.
Second, each bit in sit_area_bitmap corresponds to a valid block in a
segment. This bitmap is same to the total valid_map of f2fs_sit_entries
in SIT.
Last, each bit in main_area_bitmap corresponds to a block in main area
except meta area.
After a consistency check of each block, we set or clear the
corresponding bit of each bitmap.
From the root node, we start consistency check. The verified
information varies according to block type.
1. NODE
- Read information of node block from NAT
- Check if block address is allocated using node info.
- Check if the type of f2fs_summary related to nid in SSA is NODE.
- Update the corresponding bit in nat_area_bitmap.
- Update the corresponding bit in sit_area_bitmap.
- Set the corresponding bit in main_area_bitmap to 1.
- Then, read node block. According to its attribute, explore
inode/direct node/indirect node/double indirect node
recursively.
- If it is an inode block, we also check its xattr and hard link.
2. DATA
- Check if the type of f2fs_summary related to nid in SSA is DATA.
- Set the corresponding bits of sit_area_bitmap and
main_area_bitmap to visited
- If it is a dentry block, traverse each dentries that may be
regular
file or directory. At this time, it will check inode block again.
Finally, we verify whether
- every nat_area_bitmap is visited
- any unreachable hard link exists
- values of sit_area_bitmap and main_area_bitmap are identical
- total_valid_block_count/node_count/inode_count are correct
Usage:
o fsck.f2fs
# fsck.f2fs /dev/sdx
options:
-d debug level [default:0]
o dump.f2fs
# dump.f2fs -i [ino] /dev/sdx
# dump.f2fs -s 0~-1 /dev/sdx (SIT dump)
# dump.f2fs -a 0~-1 /dev/sdx (SSA dump)
options:
-d debug level [default:0]
-i inode no (hex)
-s [SIT dump segno from #1~#2 (decimal), for all 0~-1]
-a [SSA dump segno from #1~#2 (decimal), for all 0~-1]
Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs
dump.f2fs
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
config.private = &dump_opt;
|
2015-10-23 18:45:36 +00:00
|
|
|
} else if (!strcmp("defrag.f2fs", prog)) {
|
|
|
|
const char *option_string = "d:s:l:t:i";
|
|
|
|
|
|
|
|
config.func = DEFRAG;
|
|
|
|
while ((option = getopt(argc, argv, option_string)) != EOF) {
|
|
|
|
int ret = 0;
|
|
|
|
|
|
|
|
switch (option) {
|
|
|
|
case 'd':
|
|
|
|
config.dbg_lv = atoi(optarg);
|
|
|
|
MSG(0, "Info: Debug level = %d\n",
|
|
|
|
config.dbg_lv);
|
|
|
|
break;
|
|
|
|
case 's':
|
|
|
|
if (strncmp(optarg, "0x", 2))
|
|
|
|
ret = sscanf(optarg, "%"PRIu64"",
|
|
|
|
&config.defrag_start);
|
|
|
|
else
|
|
|
|
ret = sscanf(optarg, "%"PRIx64"",
|
|
|
|
&config.defrag_start);
|
|
|
|
break;
|
|
|
|
case 'l':
|
|
|
|
if (strncmp(optarg, "0x", 2))
|
|
|
|
ret = sscanf(optarg, "%"PRIu64"",
|
|
|
|
&config.defrag_len);
|
|
|
|
else
|
|
|
|
ret = sscanf(optarg, "%"PRIx64"",
|
|
|
|
&config.defrag_len);
|
|
|
|
break;
|
|
|
|
case 't':
|
|
|
|
if (strncmp(optarg, "0x", 2))
|
|
|
|
ret = sscanf(optarg, "%"PRIu64"",
|
|
|
|
&config.defrag_target);
|
|
|
|
else
|
|
|
|
ret = sscanf(optarg, "%"PRIx64"",
|
|
|
|
&config.defrag_target);
|
|
|
|
break;
|
|
|
|
case 'i':
|
|
|
|
config.defrag_shrink = 1;
|
|
|
|
break;
|
|
|
|
default:
|
|
|
|
MSG(0, "\tError: Unknown option %c\n", option);
|
|
|
|
defrag_usage();
|
|
|
|
break;
|
|
|
|
}
|
|
|
|
ASSERT(ret >= 0);
|
|
|
|
}
|
f2fs-tools: add fsck.f2fs and dump.f2fs
fsck.f2fs checks file system consistency, but does not repair a broken
file system yet.
dump.f2fs shows the information of a specific inode and makes dump file
of SSA and SIT.
f2fs checks file system consistency as follows:
o When data about used area and its metadata are identical,
f2fs is considered consistent. To verify such consistency, we use
three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap.
First, each bit in nat_area_bitmap corresponds to a nid in NAT.
Second, each bit in sit_area_bitmap corresponds to a valid block in a
segment. This bitmap is same to the total valid_map of f2fs_sit_entries
in SIT.
Last, each bit in main_area_bitmap corresponds to a block in main area
except meta area.
After a consistency check of each block, we set or clear the
corresponding bit of each bitmap.
From the root node, we start consistency check. The verified
information varies according to block type.
1. NODE
- Read information of node block from NAT
- Check if block address is allocated using node info.
- Check if the type of f2fs_summary related to nid in SSA is NODE.
- Update the corresponding bit in nat_area_bitmap.
- Update the corresponding bit in sit_area_bitmap.
- Set the corresponding bit in main_area_bitmap to 1.
- Then, read node block. According to its attribute, explore
inode/direct node/indirect node/double indirect node
recursively.
- If it is an inode block, we also check its xattr and hard link.
2. DATA
- Check if the type of f2fs_summary related to nid in SSA is DATA.
- Set the corresponding bits of sit_area_bitmap and
main_area_bitmap to visited
- If it is a dentry block, traverse each dentries that may be
regular
file or directory. At this time, it will check inode block again.
Finally, we verify whether
- every nat_area_bitmap is visited
- any unreachable hard link exists
- values of sit_area_bitmap and main_area_bitmap are identical
- total_valid_block_count/node_count/inode_count are correct
Usage:
o fsck.f2fs
# fsck.f2fs /dev/sdx
options:
-d debug level [default:0]
o dump.f2fs
# dump.f2fs -i [ino] /dev/sdx
# dump.f2fs -s 0~-1 /dev/sdx (SIT dump)
# dump.f2fs -a 0~-1 /dev/sdx (SSA dump)
options:
-d debug level [default:0]
-i inode no (hex)
-s [SIT dump segno from #1~#2 (decimal), for all 0~-1]
-a [SSA dump segno from #1~#2 (decimal), for all 0~-1]
Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs
dump.f2fs
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
if ((optind + 1) != argc) {
|
|
|
|
MSG(0, "\tError: Device not specified\n");
|
|
|
|
if (config.func == FSCK)
|
|
|
|
fsck_usage();
|
|
|
|
else if (config.func == DUMP)
|
|
|
|
dump_usage();
|
2015-10-23 18:45:36 +00:00
|
|
|
else if (config.func == DEFRAG)
|
|
|
|
defrag_usage();
|
f2fs-tools: add fsck.f2fs and dump.f2fs
fsck.f2fs checks file system consistency, but does not repair a broken
file system yet.
dump.f2fs shows the information of a specific inode and makes dump file
of SSA and SIT.
f2fs checks file system consistency as follows:
o When data about used area and its metadata are identical,
f2fs is considered consistent. To verify such consistency, we use
three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap.
First, each bit in nat_area_bitmap corresponds to a nid in NAT.
Second, each bit in sit_area_bitmap corresponds to a valid block in a
segment. This bitmap is same to the total valid_map of f2fs_sit_entries
in SIT.
Last, each bit in main_area_bitmap corresponds to a block in main area
except meta area.
After a consistency check of each block, we set or clear the
corresponding bit of each bitmap.
From the root node, we start consistency check. The verified
information varies according to block type.
1. NODE
- Read information of node block from NAT
- Check if block address is allocated using node info.
- Check if the type of f2fs_summary related to nid in SSA is NODE.
- Update the corresponding bit in nat_area_bitmap.
- Update the corresponding bit in sit_area_bitmap.
- Set the corresponding bit in main_area_bitmap to 1.
- Then, read node block. According to its attribute, explore
inode/direct node/indirect node/double indirect node
recursively.
- If it is an inode block, we also check its xattr and hard link.
2. DATA
- Check if the type of f2fs_summary related to nid in SSA is DATA.
- Set the corresponding bits of sit_area_bitmap and
main_area_bitmap to visited
- If it is a dentry block, traverse each dentries that may be
regular
file or directory. At this time, it will check inode block again.
Finally, we verify whether
- every nat_area_bitmap is visited
- any unreachable hard link exists
- values of sit_area_bitmap and main_area_bitmap are identical
- total_valid_block_count/node_count/inode_count are correct
Usage:
o fsck.f2fs
# fsck.f2fs /dev/sdx
options:
-d debug level [default:0]
o dump.f2fs
# dump.f2fs -i [ino] /dev/sdx
# dump.f2fs -s 0~-1 /dev/sdx (SIT dump)
# dump.f2fs -a 0~-1 /dev/sdx (SSA dump)
options:
-d debug level [default:0]
-i inode no (hex)
-s [SIT dump segno from #1~#2 (decimal), for all 0~-1]
-a [SSA dump segno from #1~#2 (decimal), for all 0~-1]
Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs
dump.f2fs
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
|
|
|
}
|
|
|
|
config.device_name = argv[optind];
|
|
|
|
}
|
|
|
|
|
2014-08-28 00:06:17 +00:00
|
|
|
static void do_fsck(struct f2fs_sb_info *sbi)
|
f2fs-tools: add fsck.f2fs and dump.f2fs
fsck.f2fs checks file system consistency, but does not repair a broken
file system yet.
dump.f2fs shows the information of a specific inode and makes dump file
of SSA and SIT.
f2fs checks file system consistency as follows:
o When data about used area and its metadata are identical,
f2fs is considered consistent. To verify such consistency, we use
three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap.
First, each bit in nat_area_bitmap corresponds to a nid in NAT.
Second, each bit in sit_area_bitmap corresponds to a valid block in a
segment. This bitmap is same to the total valid_map of f2fs_sit_entries
in SIT.
Last, each bit in main_area_bitmap corresponds to a block in main area
except meta area.
After a consistency check of each block, we set or clear the
corresponding bit of each bitmap.
From the root node, we start consistency check. The verified
information varies according to block type.
1. NODE
- Read information of node block from NAT
- Check if block address is allocated using node info.
- Check if the type of f2fs_summary related to nid in SSA is NODE.
- Update the corresponding bit in nat_area_bitmap.
- Update the corresponding bit in sit_area_bitmap.
- Set the corresponding bit in main_area_bitmap to 1.
- Then, read node block. According to its attribute, explore
inode/direct node/indirect node/double indirect node
recursively.
- If it is an inode block, we also check its xattr and hard link.
2. DATA
- Check if the type of f2fs_summary related to nid in SSA is DATA.
- Set the corresponding bits of sit_area_bitmap and
main_area_bitmap to visited
- If it is a dentry block, traverse each dentries that may be
regular
file or directory. At this time, it will check inode block again.
Finally, we verify whether
- every nat_area_bitmap is visited
- any unreachable hard link exists
- values of sit_area_bitmap and main_area_bitmap are identical
- total_valid_block_count/node_count/inode_count are correct
Usage:
o fsck.f2fs
# fsck.f2fs /dev/sdx
options:
-d debug level [default:0]
o dump.f2fs
# dump.f2fs -i [ino] /dev/sdx
# dump.f2fs -s 0~-1 /dev/sdx (SIT dump)
# dump.f2fs -a 0~-1 /dev/sdx (SSA dump)
options:
-d debug level [default:0]
-i inode no (hex)
-s [SIT dump segno from #1~#2 (decimal), for all 0~-1]
-a [SSA dump segno from #1~#2 (decimal), for all 0~-1]
Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs
dump.f2fs
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
|
|
|
{
|
2015-03-20 23:57:47 +00:00
|
|
|
struct f2fs_checkpoint *ckpt = F2FS_CKPT(sbi);
|
|
|
|
u32 flag = le32_to_cpu(ckpt->ckpt_flags);
|
f2fs-tools: add fsck.f2fs and dump.f2fs
fsck.f2fs checks file system consistency, but does not repair a broken
file system yet.
dump.f2fs shows the information of a specific inode and makes dump file
of SSA and SIT.
f2fs checks file system consistency as follows:
o When data about used area and its metadata are identical,
f2fs is considered consistent. To verify such consistency, we use
three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap.
First, each bit in nat_area_bitmap corresponds to a nid in NAT.
Second, each bit in sit_area_bitmap corresponds to a valid block in a
segment. This bitmap is same to the total valid_map of f2fs_sit_entries
in SIT.
Last, each bit in main_area_bitmap corresponds to a block in main area
except meta area.
After a consistency check of each block, we set or clear the
corresponding bit of each bitmap.
From the root node, we start consistency check. The verified
information varies according to block type.
1. NODE
- Read information of node block from NAT
- Check if block address is allocated using node info.
- Check if the type of f2fs_summary related to nid in SSA is NODE.
- Update the corresponding bit in nat_area_bitmap.
- Update the corresponding bit in sit_area_bitmap.
- Set the corresponding bit in main_area_bitmap to 1.
- Then, read node block. According to its attribute, explore
inode/direct node/indirect node/double indirect node
recursively.
- If it is an inode block, we also check its xattr and hard link.
2. DATA
- Check if the type of f2fs_summary related to nid in SSA is DATA.
- Set the corresponding bits of sit_area_bitmap and
main_area_bitmap to visited
- If it is a dentry block, traverse each dentries that may be
regular
file or directory. At this time, it will check inode block again.
Finally, we verify whether
- every nat_area_bitmap is visited
- any unreachable hard link exists
- values of sit_area_bitmap and main_area_bitmap are identical
- total_valid_block_count/node_count/inode_count are correct
Usage:
o fsck.f2fs
# fsck.f2fs /dev/sdx
options:
-d debug level [default:0]
o dump.f2fs
# dump.f2fs -i [ino] /dev/sdx
# dump.f2fs -s 0~-1 /dev/sdx (SIT dump)
# dump.f2fs -a 0~-1 /dev/sdx (SSA dump)
options:
-d debug level [default:0]
-i inode no (hex)
-s [SIT dump segno from #1~#2 (decimal), for all 0~-1]
-a [SSA dump segno from #1~#2 (decimal), for all 0~-1]
Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs
dump.f2fs
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
|
|
|
u32 blk_cnt;
|
|
|
|
|
2014-08-28 00:06:17 +00:00
|
|
|
fsck_init(sbi);
|
f2fs-tools: add fsck.f2fs and dump.f2fs
fsck.f2fs checks file system consistency, but does not repair a broken
file system yet.
dump.f2fs shows the information of a specific inode and makes dump file
of SSA and SIT.
f2fs checks file system consistency as follows:
o When data about used area and its metadata are identical,
f2fs is considered consistent. To verify such consistency, we use
three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap.
First, each bit in nat_area_bitmap corresponds to a nid in NAT.
Second, each bit in sit_area_bitmap corresponds to a valid block in a
segment. This bitmap is same to the total valid_map of f2fs_sit_entries
in SIT.
Last, each bit in main_area_bitmap corresponds to a block in main area
except meta area.
After a consistency check of each block, we set or clear the
corresponding bit of each bitmap.
From the root node, we start consistency check. The verified
information varies according to block type.
1. NODE
- Read information of node block from NAT
- Check if block address is allocated using node info.
- Check if the type of f2fs_summary related to nid in SSA is NODE.
- Update the corresponding bit in nat_area_bitmap.
- Update the corresponding bit in sit_area_bitmap.
- Set the corresponding bit in main_area_bitmap to 1.
- Then, read node block. According to its attribute, explore
inode/direct node/indirect node/double indirect node
recursively.
- If it is an inode block, we also check its xattr and hard link.
2. DATA
- Check if the type of f2fs_summary related to nid in SSA is DATA.
- Set the corresponding bits of sit_area_bitmap and
main_area_bitmap to visited
- If it is a dentry block, traverse each dentries that may be
regular
file or directory. At this time, it will check inode block again.
Finally, we verify whether
- every nat_area_bitmap is visited
- any unreachable hard link exists
- values of sit_area_bitmap and main_area_bitmap are identical
- total_valid_block_count/node_count/inode_count are correct
Usage:
o fsck.f2fs
# fsck.f2fs /dev/sdx
options:
-d debug level [default:0]
o dump.f2fs
# dump.f2fs -i [ino] /dev/sdx
# dump.f2fs -s 0~-1 /dev/sdx (SIT dump)
# dump.f2fs -a 0~-1 /dev/sdx (SSA dump)
options:
-d debug level [default:0]
-i inode no (hex)
-s [SIT dump segno from #1~#2 (decimal), for all 0~-1]
-a [SSA dump segno from #1~#2 (decimal), for all 0~-1]
Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs
dump.f2fs
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
|
|
|
|
2015-03-20 23:57:47 +00:00
|
|
|
print_cp_state(flag);
|
|
|
|
|
f2fs-tools: add fsck.f2fs and dump.f2fs
fsck.f2fs checks file system consistency, but does not repair a broken
file system yet.
dump.f2fs shows the information of a specific inode and makes dump file
of SSA and SIT.
f2fs checks file system consistency as follows:
o When data about used area and its metadata are identical,
f2fs is considered consistent. To verify such consistency, we use
three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap.
First, each bit in nat_area_bitmap corresponds to a nid in NAT.
Second, each bit in sit_area_bitmap corresponds to a valid block in a
segment. This bitmap is same to the total valid_map of f2fs_sit_entries
in SIT.
Last, each bit in main_area_bitmap corresponds to a block in main area
except meta area.
After a consistency check of each block, we set or clear the
corresponding bit of each bitmap.
From the root node, we start consistency check. The verified
information varies according to block type.
1. NODE
- Read information of node block from NAT
- Check if block address is allocated using node info.
- Check if the type of f2fs_summary related to nid in SSA is NODE.
- Update the corresponding bit in nat_area_bitmap.
- Update the corresponding bit in sit_area_bitmap.
- Set the corresponding bit in main_area_bitmap to 1.
- Then, read node block. According to its attribute, explore
inode/direct node/indirect node/double indirect node
recursively.
- If it is an inode block, we also check its xattr and hard link.
2. DATA
- Check if the type of f2fs_summary related to nid in SSA is DATA.
- Set the corresponding bits of sit_area_bitmap and
main_area_bitmap to visited
- If it is a dentry block, traverse each dentries that may be
regular
file or directory. At this time, it will check inode block again.
Finally, we verify whether
- every nat_area_bitmap is visited
- any unreachable hard link exists
- values of sit_area_bitmap and main_area_bitmap are identical
- total_valid_block_count/node_count/inode_count are correct
Usage:
o fsck.f2fs
# fsck.f2fs /dev/sdx
options:
-d debug level [default:0]
o dump.f2fs
# dump.f2fs -i [ino] /dev/sdx
# dump.f2fs -s 0~-1 /dev/sdx (SIT dump)
# dump.f2fs -a 0~-1 /dev/sdx (SSA dump)
options:
-d debug level [default:0]
-i inode no (hex)
-s [SIT dump segno from #1~#2 (decimal), for all 0~-1]
-a [SSA dump segno from #1~#2 (decimal), for all 0~-1]
Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs
dump.f2fs
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
|
|
|
fsck_chk_orphan_node(sbi);
|
|
|
|
|
2014-08-27 00:26:01 +00:00
|
|
|
/* Traverse all block recursively from root inode */
|
f2fs-tools: add fsck.f2fs and dump.f2fs
fsck.f2fs checks file system consistency, but does not repair a broken
file system yet.
dump.f2fs shows the information of a specific inode and makes dump file
of SSA and SIT.
f2fs checks file system consistency as follows:
o When data about used area and its metadata are identical,
f2fs is considered consistent. To verify such consistency, we use
three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap.
First, each bit in nat_area_bitmap corresponds to a nid in NAT.
Second, each bit in sit_area_bitmap corresponds to a valid block in a
segment. This bitmap is same to the total valid_map of f2fs_sit_entries
in SIT.
Last, each bit in main_area_bitmap corresponds to a block in main area
except meta area.
After a consistency check of each block, we set or clear the
corresponding bit of each bitmap.
From the root node, we start consistency check. The verified
information varies according to block type.
1. NODE
- Read information of node block from NAT
- Check if block address is allocated using node info.
- Check if the type of f2fs_summary related to nid in SSA is NODE.
- Update the corresponding bit in nat_area_bitmap.
- Update the corresponding bit in sit_area_bitmap.
- Set the corresponding bit in main_area_bitmap to 1.
- Then, read node block. According to its attribute, explore
inode/direct node/indirect node/double indirect node
recursively.
- If it is an inode block, we also check its xattr and hard link.
2. DATA
- Check if the type of f2fs_summary related to nid in SSA is DATA.
- Set the corresponding bits of sit_area_bitmap and
main_area_bitmap to visited
- If it is a dentry block, traverse each dentries that may be
regular
file or directory. At this time, it will check inode block again.
Finally, we verify whether
- every nat_area_bitmap is visited
- any unreachable hard link exists
- values of sit_area_bitmap and main_area_bitmap are identical
- total_valid_block_count/node_count/inode_count are correct
Usage:
o fsck.f2fs
# fsck.f2fs /dev/sdx
options:
-d debug level [default:0]
o dump.f2fs
# dump.f2fs -i [ino] /dev/sdx
# dump.f2fs -s 0~-1 /dev/sdx (SIT dump)
# dump.f2fs -a 0~-1 /dev/sdx (SSA dump)
options:
-d debug level [default:0]
-i inode no (hex)
-s [SIT dump segno from #1~#2 (decimal), for all 0~-1]
-a [SSA dump segno from #1~#2 (decimal), for all 0~-1]
Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs
dump.f2fs
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
|
|
|
blk_cnt = 1;
|
2015-03-26 00:19:13 +00:00
|
|
|
fsck_chk_node_blk(sbi, NULL, sbi->root_ino_num, (u8 *)"/",
|
2015-12-08 22:53:21 +00:00
|
|
|
F2FS_FT_DIR, TYPE_INODE, &blk_cnt, NULL, NULL);
|
2014-08-28 00:06:17 +00:00
|
|
|
fsck_verify(sbi);
|
f2fs-tools: add fsck.f2fs and dump.f2fs
fsck.f2fs checks file system consistency, but does not repair a broken
file system yet.
dump.f2fs shows the information of a specific inode and makes dump file
of SSA and SIT.
f2fs checks file system consistency as follows:
o When data about used area and its metadata are identical,
f2fs is considered consistent. To verify such consistency, we use
three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap.
First, each bit in nat_area_bitmap corresponds to a nid in NAT.
Second, each bit in sit_area_bitmap corresponds to a valid block in a
segment. This bitmap is same to the total valid_map of f2fs_sit_entries
in SIT.
Last, each bit in main_area_bitmap corresponds to a block in main area
except meta area.
After a consistency check of each block, we set or clear the
corresponding bit of each bitmap.
From the root node, we start consistency check. The verified
information varies according to block type.
1. NODE
- Read information of node block from NAT
- Check if block address is allocated using node info.
- Check if the type of f2fs_summary related to nid in SSA is NODE.
- Update the corresponding bit in nat_area_bitmap.
- Update the corresponding bit in sit_area_bitmap.
- Set the corresponding bit in main_area_bitmap to 1.
- Then, read node block. According to its attribute, explore
inode/direct node/indirect node/double indirect node
recursively.
- If it is an inode block, we also check its xattr and hard link.
2. DATA
- Check if the type of f2fs_summary related to nid in SSA is DATA.
- Set the corresponding bits of sit_area_bitmap and
main_area_bitmap to visited
- If it is a dentry block, traverse each dentries that may be
regular
file or directory. At this time, it will check inode block again.
Finally, we verify whether
- every nat_area_bitmap is visited
- any unreachable hard link exists
- values of sit_area_bitmap and main_area_bitmap are identical
- total_valid_block_count/node_count/inode_count are correct
Usage:
o fsck.f2fs
# fsck.f2fs /dev/sdx
options:
-d debug level [default:0]
o dump.f2fs
# dump.f2fs -i [ino] /dev/sdx
# dump.f2fs -s 0~-1 /dev/sdx (SIT dump)
# dump.f2fs -a 0~-1 /dev/sdx (SSA dump)
options:
-d debug level [default:0]
-i inode no (hex)
-s [SIT dump segno from #1~#2 (decimal), for all 0~-1]
-a [SSA dump segno from #1~#2 (decimal), for all 0~-1]
Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs
dump.f2fs
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
|
|
|
fsck_free(sbi);
|
|
|
|
}
|
|
|
|
|
2014-08-28 00:06:17 +00:00
|
|
|
static void do_dump(struct f2fs_sb_info *sbi)
|
f2fs-tools: add fsck.f2fs and dump.f2fs
fsck.f2fs checks file system consistency, but does not repair a broken
file system yet.
dump.f2fs shows the information of a specific inode and makes dump file
of SSA and SIT.
f2fs checks file system consistency as follows:
o When data about used area and its metadata are identical,
f2fs is considered consistent. To verify such consistency, we use
three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap.
First, each bit in nat_area_bitmap corresponds to a nid in NAT.
Second, each bit in sit_area_bitmap corresponds to a valid block in a
segment. This bitmap is same to the total valid_map of f2fs_sit_entries
in SIT.
Last, each bit in main_area_bitmap corresponds to a block in main area
except meta area.
After a consistency check of each block, we set or clear the
corresponding bit of each bitmap.
From the root node, we start consistency check. The verified
information varies according to block type.
1. NODE
- Read information of node block from NAT
- Check if block address is allocated using node info.
- Check if the type of f2fs_summary related to nid in SSA is NODE.
- Update the corresponding bit in nat_area_bitmap.
- Update the corresponding bit in sit_area_bitmap.
- Set the corresponding bit in main_area_bitmap to 1.
- Then, read node block. According to its attribute, explore
inode/direct node/indirect node/double indirect node
recursively.
- If it is an inode block, we also check its xattr and hard link.
2. DATA
- Check if the type of f2fs_summary related to nid in SSA is DATA.
- Set the corresponding bits of sit_area_bitmap and
main_area_bitmap to visited
- If it is a dentry block, traverse each dentries that may be
regular
file or directory. At this time, it will check inode block again.
Finally, we verify whether
- every nat_area_bitmap is visited
- any unreachable hard link exists
- values of sit_area_bitmap and main_area_bitmap are identical
- total_valid_block_count/node_count/inode_count are correct
Usage:
o fsck.f2fs
# fsck.f2fs /dev/sdx
options:
-d debug level [default:0]
o dump.f2fs
# dump.f2fs -i [ino] /dev/sdx
# dump.f2fs -s 0~-1 /dev/sdx (SIT dump)
# dump.f2fs -a 0~-1 /dev/sdx (SSA dump)
options:
-d debug level [default:0]
-i inode no (hex)
-s [SIT dump segno from #1~#2 (decimal), for all 0~-1]
-a [SSA dump segno from #1~#2 (decimal), for all 0~-1]
Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs
dump.f2fs
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
|
|
|
{
|
|
|
|
struct dump_option *opt = (struct dump_option *)config.private;
|
2015-01-15 00:18:15 +00:00
|
|
|
struct f2fs_checkpoint *ckpt = F2FS_CKPT(sbi);
|
|
|
|
u32 flag = le32_to_cpu(ckpt->ckpt_flags);
|
2013-07-18 02:20:05 +00:00
|
|
|
|
2014-08-28 00:06:17 +00:00
|
|
|
fsck_init(sbi);
|
f2fs-tools: add fsck.f2fs and dump.f2fs
fsck.f2fs checks file system consistency, but does not repair a broken
file system yet.
dump.f2fs shows the information of a specific inode and makes dump file
of SSA and SIT.
f2fs checks file system consistency as follows:
o When data about used area and its metadata are identical,
f2fs is considered consistent. To verify such consistency, we use
three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap.
First, each bit in nat_area_bitmap corresponds to a nid in NAT.
Second, each bit in sit_area_bitmap corresponds to a valid block in a
segment. This bitmap is same to the total valid_map of f2fs_sit_entries
in SIT.
Last, each bit in main_area_bitmap corresponds to a block in main area
except meta area.
After a consistency check of each block, we set or clear the
corresponding bit of each bitmap.
From the root node, we start consistency check. The verified
information varies according to block type.
1. NODE
- Read information of node block from NAT
- Check if block address is allocated using node info.
- Check if the type of f2fs_summary related to nid in SSA is NODE.
- Update the corresponding bit in nat_area_bitmap.
- Update the corresponding bit in sit_area_bitmap.
- Set the corresponding bit in main_area_bitmap to 1.
- Then, read node block. According to its attribute, explore
inode/direct node/indirect node/double indirect node
recursively.
- If it is an inode block, we also check its xattr and hard link.
2. DATA
- Check if the type of f2fs_summary related to nid in SSA is DATA.
- Set the corresponding bits of sit_area_bitmap and
main_area_bitmap to visited
- If it is a dentry block, traverse each dentries that may be
regular
file or directory. At this time, it will check inode block again.
Finally, we verify whether
- every nat_area_bitmap is visited
- any unreachable hard link exists
- values of sit_area_bitmap and main_area_bitmap are identical
- total_valid_block_count/node_count/inode_count are correct
Usage:
o fsck.f2fs
# fsck.f2fs /dev/sdx
options:
-d debug level [default:0]
o dump.f2fs
# dump.f2fs -i [ino] /dev/sdx
# dump.f2fs -s 0~-1 /dev/sdx (SIT dump)
# dump.f2fs -a 0~-1 /dev/sdx (SSA dump)
options:
-d debug level [default:0]
-i inode no (hex)
-s [SIT dump segno from #1~#2 (decimal), for all 0~-1]
-a [SSA dump segno from #1~#2 (decimal), for all 0~-1]
Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs
dump.f2fs
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
|
|
|
|
|
|
|
if (opt->end_sit == -1)
|
|
|
|
opt->end_sit = SM_I(sbi)->main_segments;
|
|
|
|
if (opt->end_ssa == -1)
|
|
|
|
opt->end_ssa = SM_I(sbi)->main_segments;
|
|
|
|
if (opt->start_sit != -1)
|
|
|
|
sit_dump(sbi, opt->start_sit, opt->end_sit);
|
|
|
|
if (opt->start_ssa != -1)
|
|
|
|
ssa_dump(sbi, opt->start_ssa, opt->end_ssa);
|
2013-07-18 02:20:05 +00:00
|
|
|
if (opt->blk_addr != -1) {
|
2014-12-13 21:55:59 +00:00
|
|
|
dump_info_from_blkaddr(sbi, opt->blk_addr);
|
2013-07-18 02:20:05 +00:00
|
|
|
goto cleanup;
|
|
|
|
}
|
2015-01-15 00:18:15 +00:00
|
|
|
|
2015-03-20 23:57:47 +00:00
|
|
|
print_cp_state(flag);
|
2015-01-15 00:18:15 +00:00
|
|
|
|
f2fs-tools: add fsck.f2fs and dump.f2fs
fsck.f2fs checks file system consistency, but does not repair a broken
file system yet.
dump.f2fs shows the information of a specific inode and makes dump file
of SSA and SIT.
f2fs checks file system consistency as follows:
o When data about used area and its metadata are identical,
f2fs is considered consistent. To verify such consistency, we use
three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap.
First, each bit in nat_area_bitmap corresponds to a nid in NAT.
Second, each bit in sit_area_bitmap corresponds to a valid block in a
segment. This bitmap is same to the total valid_map of f2fs_sit_entries
in SIT.
Last, each bit in main_area_bitmap corresponds to a block in main area
except meta area.
After a consistency check of each block, we set or clear the
corresponding bit of each bitmap.
From the root node, we start consistency check. The verified
information varies according to block type.
1. NODE
- Read information of node block from NAT
- Check if block address is allocated using node info.
- Check if the type of f2fs_summary related to nid in SSA is NODE.
- Update the corresponding bit in nat_area_bitmap.
- Update the corresponding bit in sit_area_bitmap.
- Set the corresponding bit in main_area_bitmap to 1.
- Then, read node block. According to its attribute, explore
inode/direct node/indirect node/double indirect node
recursively.
- If it is an inode block, we also check its xattr and hard link.
2. DATA
- Check if the type of f2fs_summary related to nid in SSA is DATA.
- Set the corresponding bits of sit_area_bitmap and
main_area_bitmap to visited
- If it is a dentry block, traverse each dentries that may be
regular
file or directory. At this time, it will check inode block again.
Finally, we verify whether
- every nat_area_bitmap is visited
- any unreachable hard link exists
- values of sit_area_bitmap and main_area_bitmap are identical
- total_valid_block_count/node_count/inode_count are correct
Usage:
o fsck.f2fs
# fsck.f2fs /dev/sdx
options:
-d debug level [default:0]
o dump.f2fs
# dump.f2fs -i [ino] /dev/sdx
# dump.f2fs -s 0~-1 /dev/sdx (SIT dump)
# dump.f2fs -a 0~-1 /dev/sdx (SSA dump)
options:
-d debug level [default:0]
-i inode no (hex)
-s [SIT dump segno from #1~#2 (decimal), for all 0~-1]
-a [SSA dump segno from #1~#2 (decimal), for all 0~-1]
Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs
dump.f2fs
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
|
|
|
dump_node(sbi, opt->nid);
|
2013-07-18 02:20:05 +00:00
|
|
|
cleanup:
|
|
|
|
fsck_free(sbi);
|
f2fs-tools: add fsck.f2fs and dump.f2fs
fsck.f2fs checks file system consistency, but does not repair a broken
file system yet.
dump.f2fs shows the information of a specific inode and makes dump file
of SSA and SIT.
f2fs checks file system consistency as follows:
o When data about used area and its metadata are identical,
f2fs is considered consistent. To verify such consistency, we use
three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap.
First, each bit in nat_area_bitmap corresponds to a nid in NAT.
Second, each bit in sit_area_bitmap corresponds to a valid block in a
segment. This bitmap is same to the total valid_map of f2fs_sit_entries
in SIT.
Last, each bit in main_area_bitmap corresponds to a block in main area
except meta area.
After a consistency check of each block, we set or clear the
corresponding bit of each bitmap.
From the root node, we start consistency check. The verified
information varies according to block type.
1. NODE
- Read information of node block from NAT
- Check if block address is allocated using node info.
- Check if the type of f2fs_summary related to nid in SSA is NODE.
- Update the corresponding bit in nat_area_bitmap.
- Update the corresponding bit in sit_area_bitmap.
- Set the corresponding bit in main_area_bitmap to 1.
- Then, read node block. According to its attribute, explore
inode/direct node/indirect node/double indirect node
recursively.
- If it is an inode block, we also check its xattr and hard link.
2. DATA
- Check if the type of f2fs_summary related to nid in SSA is DATA.
- Set the corresponding bits of sit_area_bitmap and
main_area_bitmap to visited
- If it is a dentry block, traverse each dentries that may be
regular
file or directory. At this time, it will check inode block again.
Finally, we verify whether
- every nat_area_bitmap is visited
- any unreachable hard link exists
- values of sit_area_bitmap and main_area_bitmap are identical
- total_valid_block_count/node_count/inode_count are correct
Usage:
o fsck.f2fs
# fsck.f2fs /dev/sdx
options:
-d debug level [default:0]
o dump.f2fs
# dump.f2fs -i [ino] /dev/sdx
# dump.f2fs -s 0~-1 /dev/sdx (SIT dump)
# dump.f2fs -a 0~-1 /dev/sdx (SSA dump)
options:
-d debug level [default:0]
-i inode no (hex)
-s [SIT dump segno from #1~#2 (decimal), for all 0~-1]
-a [SSA dump segno from #1~#2 (decimal), for all 0~-1]
Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs
dump.f2fs
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
|
|
|
}
|
|
|
|
|
2015-10-23 18:45:36 +00:00
|
|
|
static int do_defrag(struct f2fs_sb_info *sbi)
|
|
|
|
{
|
|
|
|
struct f2fs_super_block *sb = F2FS_RAW_SUPER(sbi);
|
|
|
|
|
|
|
|
if (config.defrag_start > get_sb(block_count))
|
|
|
|
goto out_range;
|
|
|
|
if (config.defrag_start < SM_I(sbi)->main_blkaddr)
|
|
|
|
config.defrag_start = SM_I(sbi)->main_blkaddr;
|
|
|
|
|
|
|
|
if (config.defrag_len == 0)
|
|
|
|
config.defrag_len = sbi->blocks_per_seg;
|
|
|
|
|
|
|
|
if (config.defrag_start + config.defrag_len > get_sb(block_count))
|
|
|
|
config.defrag_len = get_sb(block_count) - config.defrag_start;
|
|
|
|
|
|
|
|
if (config.defrag_target == 0) {
|
|
|
|
config.defrag_target = config.defrag_start - 1;
|
|
|
|
if (!config.defrag_shrink)
|
|
|
|
config.defrag_target += config.defrag_len + 1;
|
|
|
|
}
|
|
|
|
|
|
|
|
if (config.defrag_target < SM_I(sbi)->main_blkaddr ||
|
|
|
|
config.defrag_target > get_sb(block_count))
|
|
|
|
goto out_range;
|
|
|
|
if (config.defrag_target >= config.defrag_start &&
|
|
|
|
config.defrag_target < config.defrag_start + config.defrag_len)
|
|
|
|
goto out_range;
|
|
|
|
|
|
|
|
if (config.defrag_start > config.defrag_target)
|
|
|
|
MSG(0, "Info: Move 0x%"PRIx64" <- [0x%"PRIx64"-0x%"PRIx64"]\n",
|
|
|
|
config.defrag_target,
|
|
|
|
config.defrag_start,
|
|
|
|
config.defrag_start + config.defrag_len - 1);
|
|
|
|
else
|
|
|
|
MSG(0, "Info: Move [0x%"PRIx64"-0x%"PRIx64"] -> 0x%"PRIx64"\n",
|
|
|
|
config.defrag_start,
|
|
|
|
config.defrag_start + config.defrag_len - 1,
|
|
|
|
config.defrag_target);
|
|
|
|
|
|
|
|
return f2fs_defragment(sbi, config.defrag_start, config.defrag_len,
|
|
|
|
config.defrag_target, config.defrag_shrink);
|
|
|
|
out_range:
|
|
|
|
ASSERT_MSG("Out-of-range [0x%"PRIx64" ~ 0x%"PRIx64"] to 0x%"PRIx64"",
|
|
|
|
config.defrag_start,
|
|
|
|
config.defrag_start + config.defrag_len - 1,
|
|
|
|
config.defrag_target);
|
|
|
|
return -1;
|
|
|
|
}
|
|
|
|
|
2014-08-28 00:06:17 +00:00
|
|
|
int main(int argc, char **argv)
|
f2fs-tools: add fsck.f2fs and dump.f2fs
fsck.f2fs checks file system consistency, but does not repair a broken
file system yet.
dump.f2fs shows the information of a specific inode and makes dump file
of SSA and SIT.
f2fs checks file system consistency as follows:
o When data about used area and its metadata are identical,
f2fs is considered consistent. To verify such consistency, we use
three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap.
First, each bit in nat_area_bitmap corresponds to a nid in NAT.
Second, each bit in sit_area_bitmap corresponds to a valid block in a
segment. This bitmap is same to the total valid_map of f2fs_sit_entries
in SIT.
Last, each bit in main_area_bitmap corresponds to a block in main area
except meta area.
After a consistency check of each block, we set or clear the
corresponding bit of each bitmap.
From the root node, we start consistency check. The verified
information varies according to block type.
1. NODE
- Read information of node block from NAT
- Check if block address is allocated using node info.
- Check if the type of f2fs_summary related to nid in SSA is NODE.
- Update the corresponding bit in nat_area_bitmap.
- Update the corresponding bit in sit_area_bitmap.
- Set the corresponding bit in main_area_bitmap to 1.
- Then, read node block. According to its attribute, explore
inode/direct node/indirect node/double indirect node
recursively.
- If it is an inode block, we also check its xattr and hard link.
2. DATA
- Check if the type of f2fs_summary related to nid in SSA is DATA.
- Set the corresponding bits of sit_area_bitmap and
main_area_bitmap to visited
- If it is a dentry block, traverse each dentries that may be
regular
file or directory. At this time, it will check inode block again.
Finally, we verify whether
- every nat_area_bitmap is visited
- any unreachable hard link exists
- values of sit_area_bitmap and main_area_bitmap are identical
- total_valid_block_count/node_count/inode_count are correct
Usage:
o fsck.f2fs
# fsck.f2fs /dev/sdx
options:
-d debug level [default:0]
o dump.f2fs
# dump.f2fs -i [ino] /dev/sdx
# dump.f2fs -s 0~-1 /dev/sdx (SIT dump)
# dump.f2fs -a 0~-1 /dev/sdx (SSA dump)
options:
-d debug level [default:0]
-i inode no (hex)
-s [SIT dump segno from #1~#2 (decimal), for all 0~-1]
-a [SSA dump segno from #1~#2 (decimal), for all 0~-1]
Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs
dump.f2fs
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
|
|
|
{
|
2014-08-27 00:26:01 +00:00
|
|
|
struct f2fs_sb_info *sbi;
|
f2fs-tools: add fsck.f2fs and dump.f2fs
fsck.f2fs checks file system consistency, but does not repair a broken
file system yet.
dump.f2fs shows the information of a specific inode and makes dump file
of SSA and SIT.
f2fs checks file system consistency as follows:
o When data about used area and its metadata are identical,
f2fs is considered consistent. To verify such consistency, we use
three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap.
First, each bit in nat_area_bitmap corresponds to a nid in NAT.
Second, each bit in sit_area_bitmap corresponds to a valid block in a
segment. This bitmap is same to the total valid_map of f2fs_sit_entries
in SIT.
Last, each bit in main_area_bitmap corresponds to a block in main area
except meta area.
After a consistency check of each block, we set or clear the
corresponding bit of each bitmap.
From the root node, we start consistency check. The verified
information varies according to block type.
1. NODE
- Read information of node block from NAT
- Check if block address is allocated using node info.
- Check if the type of f2fs_summary related to nid in SSA is NODE.
- Update the corresponding bit in nat_area_bitmap.
- Update the corresponding bit in sit_area_bitmap.
- Set the corresponding bit in main_area_bitmap to 1.
- Then, read node block. According to its attribute, explore
inode/direct node/indirect node/double indirect node
recursively.
- If it is an inode block, we also check its xattr and hard link.
2. DATA
- Check if the type of f2fs_summary related to nid in SSA is DATA.
- Set the corresponding bits of sit_area_bitmap and
main_area_bitmap to visited
- If it is a dentry block, traverse each dentries that may be
regular
file or directory. At this time, it will check inode block again.
Finally, we verify whether
- every nat_area_bitmap is visited
- any unreachable hard link exists
- values of sit_area_bitmap and main_area_bitmap are identical
- total_valid_block_count/node_count/inode_count are correct
Usage:
o fsck.f2fs
# fsck.f2fs /dev/sdx
options:
-d debug level [default:0]
o dump.f2fs
# dump.f2fs -i [ino] /dev/sdx
# dump.f2fs -s 0~-1 /dev/sdx (SIT dump)
# dump.f2fs -a 0~-1 /dev/sdx (SSA dump)
options:
-d debug level [default:0]
-i inode no (hex)
-s [SIT dump segno from #1~#2 (decimal), for all 0~-1]
-a [SSA dump segno from #1~#2 (decimal), for all 0~-1]
Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs
dump.f2fs
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
|
|
|
int ret = 0;
|
|
|
|
|
|
|
|
f2fs_init_configuration(&config);
|
|
|
|
|
|
|
|
f2fs_parse_options(argc, argv);
|
|
|
|
|
2015-11-22 02:53:07 +00:00
|
|
|
if (f2fs_dev_is_umounted(&config) < 0) {
|
2015-10-23 18:45:36 +00:00
|
|
|
if (!config.ro || config.func == DEFRAG) {
|
2015-11-22 02:53:07 +00:00
|
|
|
MSG(0, "\tError: Not available on mounted device!\n");
|
|
|
|
return -1;
|
|
|
|
}
|
|
|
|
|
|
|
|
/* allow ro-mounted partition */
|
|
|
|
MSG(0, "Info: Check FS only due to RO\n");
|
|
|
|
config.fix_on = 0;
|
|
|
|
config.auto_fix = 0;
|
|
|
|
}
|
f2fs-tools: add fsck.f2fs and dump.f2fs
fsck.f2fs checks file system consistency, but does not repair a broken
file system yet.
dump.f2fs shows the information of a specific inode and makes dump file
of SSA and SIT.
f2fs checks file system consistency as follows:
o When data about used area and its metadata are identical,
f2fs is considered consistent. To verify such consistency, we use
three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap.
First, each bit in nat_area_bitmap corresponds to a nid in NAT.
Second, each bit in sit_area_bitmap corresponds to a valid block in a
segment. This bitmap is same to the total valid_map of f2fs_sit_entries
in SIT.
Last, each bit in main_area_bitmap corresponds to a block in main area
except meta area.
After a consistency check of each block, we set or clear the
corresponding bit of each bitmap.
From the root node, we start consistency check. The verified
information varies according to block type.
1. NODE
- Read information of node block from NAT
- Check if block address is allocated using node info.
- Check if the type of f2fs_summary related to nid in SSA is NODE.
- Update the corresponding bit in nat_area_bitmap.
- Update the corresponding bit in sit_area_bitmap.
- Set the corresponding bit in main_area_bitmap to 1.
- Then, read node block. According to its attribute, explore
inode/direct node/indirect node/double indirect node
recursively.
- If it is an inode block, we also check its xattr and hard link.
2. DATA
- Check if the type of f2fs_summary related to nid in SSA is DATA.
- Set the corresponding bits of sit_area_bitmap and
main_area_bitmap to visited
- If it is a dentry block, traverse each dentries that may be
regular
file or directory. At this time, it will check inode block again.
Finally, we verify whether
- every nat_area_bitmap is visited
- any unreachable hard link exists
- values of sit_area_bitmap and main_area_bitmap are identical
- total_valid_block_count/node_count/inode_count are correct
Usage:
o fsck.f2fs
# fsck.f2fs /dev/sdx
options:
-d debug level [default:0]
o dump.f2fs
# dump.f2fs -i [ino] /dev/sdx
# dump.f2fs -s 0~-1 /dev/sdx (SIT dump)
# dump.f2fs -a 0~-1 /dev/sdx (SSA dump)
options:
-d debug level [default:0]
-i inode no (hex)
-s [SIT dump segno from #1~#2 (decimal), for all 0~-1]
-a [SSA dump segno from #1~#2 (decimal), for all 0~-1]
Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs
dump.f2fs
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
|
|
|
|
|
|
|
/* Get device */
|
|
|
|
if (f2fs_get_device_info(&config) < 0)
|
|
|
|
return -1;
|
2014-08-27 00:26:01 +00:00
|
|
|
fsck_again:
|
|
|
|
memset(&gfsck, 0, sizeof(gfsck));
|
|
|
|
gfsck.sbi.fsck = &gfsck;
|
|
|
|
sbi = &gfsck.sbi;
|
f2fs-tools: add fsck.f2fs and dump.f2fs
fsck.f2fs checks file system consistency, but does not repair a broken
file system yet.
dump.f2fs shows the information of a specific inode and makes dump file
of SSA and SIT.
f2fs checks file system consistency as follows:
o When data about used area and its metadata are identical,
f2fs is considered consistent. To verify such consistency, we use
three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap.
First, each bit in nat_area_bitmap corresponds to a nid in NAT.
Second, each bit in sit_area_bitmap corresponds to a valid block in a
segment. This bitmap is same to the total valid_map of f2fs_sit_entries
in SIT.
Last, each bit in main_area_bitmap corresponds to a block in main area
except meta area.
After a consistency check of each block, we set or clear the
corresponding bit of each bitmap.
From the root node, we start consistency check. The verified
information varies according to block type.
1. NODE
- Read information of node block from NAT
- Check if block address is allocated using node info.
- Check if the type of f2fs_summary related to nid in SSA is NODE.
- Update the corresponding bit in nat_area_bitmap.
- Update the corresponding bit in sit_area_bitmap.
- Set the corresponding bit in main_area_bitmap to 1.
- Then, read node block. According to its attribute, explore
inode/direct node/indirect node/double indirect node
recursively.
- If it is an inode block, we also check its xattr and hard link.
2. DATA
- Check if the type of f2fs_summary related to nid in SSA is DATA.
- Set the corresponding bits of sit_area_bitmap and
main_area_bitmap to visited
- If it is a dentry block, traverse each dentries that may be
regular
file or directory. At this time, it will check inode block again.
Finally, we verify whether
- every nat_area_bitmap is visited
- any unreachable hard link exists
- values of sit_area_bitmap and main_area_bitmap are identical
- total_valid_block_count/node_count/inode_count are correct
Usage:
o fsck.f2fs
# fsck.f2fs /dev/sdx
options:
-d debug level [default:0]
o dump.f2fs
# dump.f2fs -i [ino] /dev/sdx
# dump.f2fs -s 0~-1 /dev/sdx (SIT dump)
# dump.f2fs -a 0~-1 /dev/sdx (SSA dump)
options:
-d debug level [default:0]
-i inode no (hex)
-s [SIT dump segno from #1~#2 (decimal), for all 0~-1]
-a [SSA dump segno from #1~#2 (decimal), for all 0~-1]
Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs
dump.f2fs
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
|
|
|
|
2014-09-03 01:07:35 +00:00
|
|
|
ret = f2fs_do_mount(sbi);
|
2016-01-15 04:44:13 +00:00
|
|
|
if (ret != 0) {
|
|
|
|
if (ret == 1) {
|
|
|
|
MSG(0, "Info: No error was reported\n");
|
|
|
|
ret = 0;
|
|
|
|
}
|
2015-10-23 18:45:36 +00:00
|
|
|
goto out_err;
|
2016-01-15 04:44:13 +00:00
|
|
|
}
|
f2fs-tools: add fsck.f2fs and dump.f2fs
fsck.f2fs checks file system consistency, but does not repair a broken
file system yet.
dump.f2fs shows the information of a specific inode and makes dump file
of SSA and SIT.
f2fs checks file system consistency as follows:
o When data about used area and its metadata are identical,
f2fs is considered consistent. To verify such consistency, we use
three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap.
First, each bit in nat_area_bitmap corresponds to a nid in NAT.
Second, each bit in sit_area_bitmap corresponds to a valid block in a
segment. This bitmap is same to the total valid_map of f2fs_sit_entries
in SIT.
Last, each bit in main_area_bitmap corresponds to a block in main area
except meta area.
After a consistency check of each block, we set or clear the
corresponding bit of each bitmap.
From the root node, we start consistency check. The verified
information varies according to block type.
1. NODE
- Read information of node block from NAT
- Check if block address is allocated using node info.
- Check if the type of f2fs_summary related to nid in SSA is NODE.
- Update the corresponding bit in nat_area_bitmap.
- Update the corresponding bit in sit_area_bitmap.
- Set the corresponding bit in main_area_bitmap to 1.
- Then, read node block. According to its attribute, explore
inode/direct node/indirect node/double indirect node
recursively.
- If it is an inode block, we also check its xattr and hard link.
2. DATA
- Check if the type of f2fs_summary related to nid in SSA is DATA.
- Set the corresponding bits of sit_area_bitmap and
main_area_bitmap to visited
- If it is a dentry block, traverse each dentries that may be
regular
file or directory. At this time, it will check inode block again.
Finally, we verify whether
- every nat_area_bitmap is visited
- any unreachable hard link exists
- values of sit_area_bitmap and main_area_bitmap are identical
- total_valid_block_count/node_count/inode_count are correct
Usage:
o fsck.f2fs
# fsck.f2fs /dev/sdx
options:
-d debug level [default:0]
o dump.f2fs
# dump.f2fs -i [ino] /dev/sdx
# dump.f2fs -s 0~-1 /dev/sdx (SIT dump)
# dump.f2fs -a 0~-1 /dev/sdx (SSA dump)
options:
-d debug level [default:0]
-i inode no (hex)
-s [SIT dump segno from #1~#2 (decimal), for all 0~-1]
-a [SSA dump segno from #1~#2 (decimal), for all 0~-1]
Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs
dump.f2fs
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
|
|
|
|
|
|
|
switch (config.func) {
|
2014-08-27 00:26:01 +00:00
|
|
|
case FSCK:
|
2014-08-28 00:06:17 +00:00
|
|
|
do_fsck(sbi);
|
2014-08-27 00:26:01 +00:00
|
|
|
break;
|
|
|
|
case DUMP:
|
2014-08-28 00:06:17 +00:00
|
|
|
do_dump(sbi);
|
2014-08-27 00:26:01 +00:00
|
|
|
break;
|
2015-10-23 18:45:36 +00:00
|
|
|
case DEFRAG:
|
2016-01-15 04:44:13 +00:00
|
|
|
ret = do_defrag(sbi);
|
|
|
|
if (ret)
|
2015-10-23 18:45:36 +00:00
|
|
|
goto out_err;
|
|
|
|
break;
|
f2fs-tools: add fsck.f2fs and dump.f2fs
fsck.f2fs checks file system consistency, but does not repair a broken
file system yet.
dump.f2fs shows the information of a specific inode and makes dump file
of SSA and SIT.
f2fs checks file system consistency as follows:
o When data about used area and its metadata are identical,
f2fs is considered consistent. To verify such consistency, we use
three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap.
First, each bit in nat_area_bitmap corresponds to a nid in NAT.
Second, each bit in sit_area_bitmap corresponds to a valid block in a
segment. This bitmap is same to the total valid_map of f2fs_sit_entries
in SIT.
Last, each bit in main_area_bitmap corresponds to a block in main area
except meta area.
After a consistency check of each block, we set or clear the
corresponding bit of each bitmap.
From the root node, we start consistency check. The verified
information varies according to block type.
1. NODE
- Read information of node block from NAT
- Check if block address is allocated using node info.
- Check if the type of f2fs_summary related to nid in SSA is NODE.
- Update the corresponding bit in nat_area_bitmap.
- Update the corresponding bit in sit_area_bitmap.
- Set the corresponding bit in main_area_bitmap to 1.
- Then, read node block. According to its attribute, explore
inode/direct node/indirect node/double indirect node
recursively.
- If it is an inode block, we also check its xattr and hard link.
2. DATA
- Check if the type of f2fs_summary related to nid in SSA is DATA.
- Set the corresponding bits of sit_area_bitmap and
main_area_bitmap to visited
- If it is a dentry block, traverse each dentries that may be
regular
file or directory. At this time, it will check inode block again.
Finally, we verify whether
- every nat_area_bitmap is visited
- any unreachable hard link exists
- values of sit_area_bitmap and main_area_bitmap are identical
- total_valid_block_count/node_count/inode_count are correct
Usage:
o fsck.f2fs
# fsck.f2fs /dev/sdx
options:
-d debug level [default:0]
o dump.f2fs
# dump.f2fs -i [ino] /dev/sdx
# dump.f2fs -s 0~-1 /dev/sdx (SIT dump)
# dump.f2fs -a 0~-1 /dev/sdx (SSA dump)
options:
-d debug level [default:0]
-i inode no (hex)
-s [SIT dump segno from #1~#2 (decimal), for all 0~-1]
-a [SSA dump segno from #1~#2 (decimal), for all 0~-1]
Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs
dump.f2fs
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
|
|
|
}
|
|
|
|
|
2013-07-18 02:20:05 +00:00
|
|
|
f2fs_do_umount(sbi);
|
2015-10-23 18:45:36 +00:00
|
|
|
|
2014-08-27 00:26:01 +00:00
|
|
|
if (config.func == FSCK && config.bug_on) {
|
2015-11-22 02:53:07 +00:00
|
|
|
if (!config.ro && config.fix_on == 0 && config.auto_fix == 0) {
|
2014-08-27 00:26:01 +00:00
|
|
|
char ans[255] = {0};
|
|
|
|
retry:
|
|
|
|
printf("Do you want to fix this partition? [Y/N] ");
|
|
|
|
ret = scanf("%s", ans);
|
|
|
|
ASSERT(ret >= 0);
|
|
|
|
if (!strcasecmp(ans, "y"))
|
2014-09-04 02:41:44 +00:00
|
|
|
config.fix_on = 1;
|
2014-08-27 00:26:01 +00:00
|
|
|
else if (!strcasecmp(ans, "n"))
|
2014-09-04 02:41:44 +00:00
|
|
|
config.fix_on = 0;
|
2014-08-27 00:26:01 +00:00
|
|
|
else
|
|
|
|
goto retry;
|
2014-09-04 02:41:44 +00:00
|
|
|
|
|
|
|
if (config.fix_on)
|
|
|
|
goto fsck_again;
|
2014-08-27 00:26:01 +00:00
|
|
|
}
|
|
|
|
}
|
2014-06-13 07:51:32 +00:00
|
|
|
f2fs_finalize_device(&config);
|
|
|
|
|
f2fs-tools: add fsck.f2fs and dump.f2fs
fsck.f2fs checks file system consistency, but does not repair a broken
file system yet.
dump.f2fs shows the information of a specific inode and makes dump file
of SSA and SIT.
f2fs checks file system consistency as follows:
o When data about used area and its metadata are identical,
f2fs is considered consistent. To verify such consistency, we use
three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap.
First, each bit in nat_area_bitmap corresponds to a nid in NAT.
Second, each bit in sit_area_bitmap corresponds to a valid block in a
segment. This bitmap is same to the total valid_map of f2fs_sit_entries
in SIT.
Last, each bit in main_area_bitmap corresponds to a block in main area
except meta area.
After a consistency check of each block, we set or clear the
corresponding bit of each bitmap.
From the root node, we start consistency check. The verified
information varies according to block type.
1. NODE
- Read information of node block from NAT
- Check if block address is allocated using node info.
- Check if the type of f2fs_summary related to nid in SSA is NODE.
- Update the corresponding bit in nat_area_bitmap.
- Update the corresponding bit in sit_area_bitmap.
- Set the corresponding bit in main_area_bitmap to 1.
- Then, read node block. According to its attribute, explore
inode/direct node/indirect node/double indirect node
recursively.
- If it is an inode block, we also check its xattr and hard link.
2. DATA
- Check if the type of f2fs_summary related to nid in SSA is DATA.
- Set the corresponding bits of sit_area_bitmap and
main_area_bitmap to visited
- If it is a dentry block, traverse each dentries that may be
regular
file or directory. At this time, it will check inode block again.
Finally, we verify whether
- every nat_area_bitmap is visited
- any unreachable hard link exists
- values of sit_area_bitmap and main_area_bitmap are identical
- total_valid_block_count/node_count/inode_count are correct
Usage:
o fsck.f2fs
# fsck.f2fs /dev/sdx
options:
-d debug level [default:0]
o dump.f2fs
# dump.f2fs -i [ino] /dev/sdx
# dump.f2fs -s 0~-1 /dev/sdx (SIT dump)
# dump.f2fs -a 0~-1 /dev/sdx (SSA dump)
options:
-d debug level [default:0]
-i inode no (hex)
-s [SIT dump segno from #1~#2 (decimal), for all 0~-1]
-a [SSA dump segno from #1~#2 (decimal), for all 0~-1]
Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs
dump.f2fs
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
|
|
|
printf("\nDone.\n");
|
2014-08-28 00:06:17 +00:00
|
|
|
return 0;
|
2015-10-23 18:45:36 +00:00
|
|
|
|
|
|
|
out_err:
|
|
|
|
if (sbi->ckpt)
|
|
|
|
free(sbi->ckpt);
|
|
|
|
if (sbi->raw_super)
|
|
|
|
free(sbi->raw_super);
|
2016-01-15 04:44:13 +00:00
|
|
|
return ret;
|
f2fs-tools: add fsck.f2fs and dump.f2fs
fsck.f2fs checks file system consistency, but does not repair a broken
file system yet.
dump.f2fs shows the information of a specific inode and makes dump file
of SSA and SIT.
f2fs checks file system consistency as follows:
o When data about used area and its metadata are identical,
f2fs is considered consistent. To verify such consistency, we use
three bitmaps: nat_area_bitmap, sit_area_bitmap, and main_area_bitmap.
First, each bit in nat_area_bitmap corresponds to a nid in NAT.
Second, each bit in sit_area_bitmap corresponds to a valid block in a
segment. This bitmap is same to the total valid_map of f2fs_sit_entries
in SIT.
Last, each bit in main_area_bitmap corresponds to a block in main area
except meta area.
After a consistency check of each block, we set or clear the
corresponding bit of each bitmap.
From the root node, we start consistency check. The verified
information varies according to block type.
1. NODE
- Read information of node block from NAT
- Check if block address is allocated using node info.
- Check if the type of f2fs_summary related to nid in SSA is NODE.
- Update the corresponding bit in nat_area_bitmap.
- Update the corresponding bit in sit_area_bitmap.
- Set the corresponding bit in main_area_bitmap to 1.
- Then, read node block. According to its attribute, explore
inode/direct node/indirect node/double indirect node
recursively.
- If it is an inode block, we also check its xattr and hard link.
2. DATA
- Check if the type of f2fs_summary related to nid in SSA is DATA.
- Set the corresponding bits of sit_area_bitmap and
main_area_bitmap to visited
- If it is a dentry block, traverse each dentries that may be
regular
file or directory. At this time, it will check inode block again.
Finally, we verify whether
- every nat_area_bitmap is visited
- any unreachable hard link exists
- values of sit_area_bitmap and main_area_bitmap are identical
- total_valid_block_count/node_count/inode_count are correct
Usage:
o fsck.f2fs
# fsck.f2fs /dev/sdx
options:
-d debug level [default:0]
o dump.f2fs
# dump.f2fs -i [ino] /dev/sdx
# dump.f2fs -s 0~-1 /dev/sdx (SIT dump)
# dump.f2fs -a 0~-1 /dev/sdx (SSA dump)
options:
-d debug level [default:0]
-i inode no (hex)
-s [SIT dump segno from #1~#2 (decimal), for all 0~-1]
-a [SSA dump segno from #1~#2 (decimal), for all 0~-1]
Note: To use dump.f2fs, please run make install or ln -s fsck.f2fs
dump.f2fs
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Byoung Geun Kim <bgbg.kim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
2013-07-04 08:11:32 +00:00
|
|
|
}
|