- very minor performance boost from not doing stupid things :)
- minor change to 3d shockwave sizing to better approximate 2d effect movements
- for shields, Gobal_tris was only holding half as many as the game can/will use, buffer is now set to full size to avoid possible rendering issues
- removed extra tcache_set on OGL spec map code, not sure how that slipped in
more non-standard res fixing
- I think everything should default to resize now (much easier than having to figure that crap out)
- new mouse_get_pos_unscaled() function to return 1024x768/640x480 relative values so we don't have to do it later
- lots of little cleanups which fix several strange offset/size problems
- fix gr_resize/unsize_screen_pos() so that it won't wrap on int (took too long to track this down)
- remove all bitmap section support and fix problems with previous attempt
( code/bmpman/bmpman.cpp, code/bmpman/bmpman.h, code/globalincs/pstypes.h,
code/graphics/2d.cpp, code/graphics/2d.h code/graphics/grd3dbmpman.cpp,
code/graphics/grd3dinternal.h, code/graphics/grd3drender.cpp, code/graphics/grd3dtexture.cpp,
code/graphics/grinternal.h, code/graphics/gropengl.cpp, code/graphics/gropengl.h,
code/graphics/gropengllight.cpp, code/graphics/gropengltexture.cpp, code/graphics/gropengltexture.h,
code/graphics/tmapper.h, code/network/multi_pinfo.cpp, code/radar/radarorb.cpp
code/render/3ddraw.cpp )
- use CLAMP() define in gropengl.h for gropengllight instead of single clamp() function
- remove some old/outdated code from gropengl.cpp and gropengltexture.cpp
some header cleaning
only one tmapper_internal for OGL, don't use more than two tex/pass now
seperate out 2d matrix mode to allow -2d_poof in OGL and maybe fix missing
interface when set 3d matrix stuff doesn't have corresponding end
add dump_frame stuff for OGL, mostly useless but allows trailer recording
OGL can take advantage of this if they want but it won't break
anything if they don't. also state block code has been implemented,
that's totaly internal to D3D no high level code is involved.
Changed htl to be on by default, command now -nohtl
Changed D3D to use a 2D vertex for 2D operations which should cut down on redundant data having to go though the system.
Added small change to all -start_mission flag to take you to any mission by filename, very useful for testing.
Removed old dshow code and took away timerbar compile flag condition since it uses a runtime flag now.
OK, these changes effect a lot of file, I suggest everyone updates ASAP:
Removal of many files from project.
Removal of meanless Gr_bitmap_poly variable.
Removal of glide, directdraw, software modules all links to them, and all code specific to those paths.
Removal of redundant Fred paths that arent needed for Fred OGL.
Have seriously tidied the graphics initialisation code and added generic non standard mode functionality.
Fixed many D3D non standard mode bugs and brought OGL up to the same level.
Removed texture section support for D3D8, voodoo 2 and 3 cards will no longer run under fs2_open in D3D, same goes for any card with a maximum texture size less than 1024.
Added stats command for ingame stats on memory usage.
Trys to play intro.mve and intro.avi, just to be safe since its not set by table.
Added fix for fonts wrapping round in non standard hi res modes.
Changed D3D mipmapping to a good value to suit htl mode.
Added new fog colour method which makes use of the bitmap, making this htl feature backcompatible again.
Made some commandline variables fit the naming standard.
Changed timerbar system not to run pushes and pops if its not in use.
Put in a note about not uncommenting asserts.
Fixed up a lot of missing POP's on early returns?
Perhaps the motivation for Assert functionality getting commented out?
Fixed up some bad asserts.
Changed nebula poofs to render in 2D in htl, it makes it look how it used to in non htl. (neb.cpp,1248)
Before the poofs were creating a nasty stripe effect where they intersected with ships hulls.
Put in a special check for the signs of that D3D init bug I need to lock down.
started work on fixing the node model not rendering,
but most of that got commented out so I wouldn't have to deal with it
while mucking about with the polylist
In D3D red is general processing (and generic graphics), green is 2D rendering, dark blue is 3D unlit, light blue is HT&L renders and yellow is the presentation of the frame to D3D. OGL is all red for now. Use compile flag TIMERBAR_ON with code lib to activate it.
Also updated some more D3D device stuff that might get a bit more speed out of some cards.
Fixed up some more non standard res stuff
Improved selection of device type, this includes using a pure device when allowed which means dev should not use Get* functions in D3D
Made fade in credits work
Stopped a call to gr_reser_lighting() in non htl mode when the pointer was NULL, was causing a crash loading a fogged level
Deleted directx8 directory content, has never been needed.
Put my 32bit PCX loading under PCX_32 compile flag until its working.
Fixed a bug with res 640x480 I introduced with my non standard mode code.
Changed JPG and TGA loading command line param to "-t32"
Also 32 bit PCX, but it still has some bugs to be worked out
Moved convert_24_to_16 out of the bitmap pfunction structures and into packunpack.cpp because thats the only place that uses it.
taylor