Now that arm_load_kernel doesn't insist on a kernel filename
being present, we can remove some unnecessary conditionals
in board models.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1379980897-21277-3-git-send-email-peter.maydell@linaro.org
Typically ARM boards will have some kind of flash which might contain
a boot ROM; it's therefore a valid use case to provide only an
image for the boot ROM and not require QEMU's internal boot loader
at all. Remove the fatal error if -kernel isn't specified.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1379980897-21277-2-git-send-email-peter.maydell@linaro.org
When AHCI executes an asynchronous IDE command, it checked DRDY without
checking either DRQ or BSY. This sometimes caused interrupt to be sent
before command is actually completed.
This resulted in a race condition: if guest then managed to access the
device before command has completed, it would hang waiting for an
interrupt.
This was observed with windows 7 guests.
To fix, check for DRQ or BSY in additiona to DRDY, if set,
the command is asynchronous so delay the interrupt until
asynchronous done callback is invoked.
Reported-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
compatiblity -> compatibility
continously -> continuously
existance -> existence
usefull -> useful
shoudl -> should
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Instead of relying on cpu_model, obtain the device tree node label
per CPU. Use DeviceClass::fw_name as source.
Whenever DeviceClass::fw_name is unknown, default to "PowerPC,UNKNOWN".
As a consequence, spapr_fixup_cpu_dt() can operate on each CPU's fw_name,
obsoleting sPAPREnvironment::cpu_model, and spapr_create_fdt_skel() can
drop its cpu_model argument.
Signed-off-by: Prerna Saxena <prerna@linux.vnet.ibm.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This enables IRQFD for LSI (level triggered INTx interrupts) by adding
a spapr_route_intx_pin_to_irq() callback to the sPAPR PCI host bus. This
callback is called to know the global interrupt number to link resampling fd
with IRQFD's fd in KVM.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
This enables IRQFD support for sPAPR. The feature decreases the latency
of interrupt handling.
To enable IRQFD for MSI, this sets kvm_gsi_direct_mapping to true which
enables direct MSI mapping.
To enable IRQFD for LSI (level triggered INTx interrupts), a PCI host bus
callback is required. The patch for that is coming next.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
This implements H_XIRR_X hypercall in addition to H_XIRR as
it is mandatory for PAPR+ and there is no way for the guest to
detect whether it is supported or not so just add it.
As the Partition Adjunct Option is not supported at the moment,
the CPPR parameter of the hypercall is ignored.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds support for the H_IPOLL hypercall which the guest
uses to poll for a pending interrupt. This hypercall is
mandatory for PAPR+ and there is no way for the guest to
detect whether it is supported or not so just add it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Recent (host) kernels support emulating the PAPR defined "XICS" interrupt
controller system within KVM. This patch allows qemu to initialize and
configure the in-kernel XICS, and keep its state in sync with qemu's XICS
state as necessary.
This should give considerable performance improvements. e.g. on a simple
IPI ping-pong test between hardware threads, using qemu XICS gives us
around 5,000 irqs/second, whereas the in-kernel XICS gives us around
70,000 irqs/s on the same hardware configuration.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
[Mike Qiu <qiudayu@linux.vnet.ibm.com>: fixed mistype which caused ics_set_kvm_state() to fail]
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds a cpu_setup callback to the XICS device class (as XICS-KVM
will do it different), xics_cpu_setup() will call it if it is set.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
The upcoming XICS-KVM support will use bits of emulated XICS code.
So this introduces new level of hierarchy - "xics-common" class. Both
emulated XICS and XICS-KVM will inherit from it and override class
callbacks when required.
The new "xics-common" class implements:
1. replaces static "nr_irqs" and "nr_servers" properties with
the dynamic ones and adds callbacks to be executed when properties
are set.
2. xics_cpu_setup() callback renamed to xics_common_cpu_setup() as
it is a common part for both XICS'es
3. xics_reset() renamed to xics_common_reset() for the same reason.
The emulated XICS changes:
1. the part of xics_realize() which creates ICPs is moved to
the "nr_servers" property callback as realize() is too late to
create/initialize devices and instance_init() is too early to create
devices as the number of child devices comes via the "nr_servers"
property.
2. added ics_initfn() which does a little part of what xics_realize() did.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds missing const specifiers to ICS and ICP TypeInfo's.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This fixes XICS according new QOM rules.
This converts ICS's init() callbacks to realize().
This converts legacy qdev_init_nofail() to property_set(realized).
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The upcoming support of in-kernel XICS will redefine migration callbacks
for both ICS and ICP so classes and callback pointers are added.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
This replaces old-style fprintf with new style error_report.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
This moves the xics_cpu_setup() call after kvmppc_set_papr()
in order to get VCPUs initialized as this is required by upcoming
XICS-KVM.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
This simple change makes following patches nicer.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
On the real hardware, RTAS is called in real mode and therefore
top 4 bits of the address passed in the call are ignored.
So does the patch.
This converts h_rtas() to use existing rtas_ld() handlers.
This fixed rtas_ld()/rtas_st() to ignore top 4 bits.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
PAPR+ says that no "ibm,purr" tells the guest that H_PURR is not
supported. However some guests still try calling H_PURR on POWER7 unless
the property is present and equal to 0. This adds the property for CPUs
supporting the PURR special register.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
At the moment the size of the buffer is set to 64K which is
enough for approximately 150 VCPUs which is not the limit.
This increases the buffer up to 256K which allows having
a tree for approximately 600 VCPUs which is way beyond the real
number we need.
As only the real size of the tree is copied to the guest, there
will be no impact on existing configurations.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
Try loading the kernel as little endian if it fails big endian.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
With streams the endpoint context dequeue pointer should point to the
dequeue value for the currently active stream.
At least Linux guests expect it to point to value set by an set_ep_dequeue
upon completion of the set_ep_dequeue (before kicking the ep).
Otherwise the Linux kernel will complain (and things won't work):
xhci_hcd 0000:00:05.0: Mismatch between completed Set TR Deq Ptr command & xHCI internal state.
xhci_hcd 0000:00:05.0: ep deq seg = ffff8800366f0880, deq ptr = ffff8800366ec010
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
As we should per the XHCI spec "4.6.9 Stop Endpoint".
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Since qemu's USB model is geared towards emulated devices cancellation
is instanteneous, so no need to wait for cancellation to complete, as
such there is no wait for cancellation code, and the cancelled bool
as well as the bogus comment about it can be removed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
If we detach the kernel drivers on the first set_config, then they will
be still attached when the device gets its initial reset. Causing the drivers
to re-initialize the device after the reset, dirtying the device state.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Quoting from: linux/Documentation/ABI/stable/sysfs-bus-usb:
Note that some devices, in violation of the USB spec, have a
configuration with a value equal to 0. Writing 0 to
bConfigurationValue for these devices will install that
configuration, rather then unconfigure the device.
So don't compare the configuration value against 0 to check for unconfigured
devices, instead check for a LIBUSB_ERROR_NOT_FOUND return from
libusb_get_active_config_descriptor().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The guest will issue an initial device reset when the device is attached, but
since the current usb-host-libusb code only actually does the reset when
udev->configuration != 0, and on attach the device is not yet configured,
the reset gets ignored. This means that the device gets passed to the guest
in an unknown state, which is not good.
The udev->configuration check is there because of the release / claim
interfaces done around the libusb_device_reset call, but these are not
necessary. If interfaces are claimed when libusb_device_reset gets called
libusb will release + reclaim them itself.
The usb_host_ep_update call also is not necessary. If the reset succeeds the
original config and interface alt settings will be restored.
Last if the reset fails, that means the device has either disconnected or
morphed into an another device and has been completely re-enumerated,
so it is treated by the host as a new device and our handle is invalid,
so on reset failure we need to call usb_host_nodev().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
# By Paolo Bonzini (2) and Jan Kiszka (1)
# Via Gleb Natapov
* qemu-kvm/uq/master:
kvmvapic: Prevent reading beyond the end of guest RAM
x86: cpuid: reconstruct leaf 0Dh data
x86: fix migration from pre-version 12
Message-id: 1382108641-4862-1-git-send-email-pbonzini@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
# By Amos Kong
# Via Stefan Hajnoczi
* stefanha/net:
net/rtl8139: update network information when macaddr is changed in guest
net/e1000: update network information when macaddr is changed in guest
net: update nic info during device reset
Message-id: 1382103314-21608-1-git-send-email-stefanha@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
# By Fam Zheng (3) and others
# Via Stefan Hajnoczi
* stefanha/block:
vmdk: fix VMFS extent parsing
vmdk: Only read cid from image file when opening
virtio: Remove unneeded memcpy
block/raw-win32: Always use -errno in hdev_open
blockdev: fix cdrom read_only flag
sd: Avoid access to NULL BlockDriverState
hmp: drop bogus "[not inserted]"
Message-id: 1382105915-27735-1-git-send-email-stefanha@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
# By Paolo Bonzini (10) and others
# Via Paolo Bonzini
* bonzini/iommu-for-anthony:
exec: remove qemu_safe_ram_ptr
icount: make it thread-safe
icount: document (future) locking rules for icount
icount: prepare the code for future races in calling qemu_clock_warp
icount: reorganize icount_warp_rt
icount: use cpu_get_icount() directly
timer: add timer_mod_anticipate and timer_mod_anticipate_ns
timer: extract timer_mod_ns_locked and timerlist_rearm
timer: make qemu_clock_enable sync between disable and timer's cb
qemu-thread: add QemuEvent
timer: protect timers_state's clock with seqlock
seqlock: introduce read-write seqlock
vga: Mark relevant portio lists regions as coalesced MMIO flushing
cirrus: Mark vga io region as coalesced MMIO flushing
portio: Allow to mark portio lists as coalesced MMIO flushing
compatfd: switch to QemuThread
memory: fix 128 arithmetic in info mtree
Message-id: 1382024935-28297-1-git-send-email-pbonzini@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
# By Peter Maydell (3) and Ákos Kovács (2)
# Via Paolo Bonzini
* bonzini/configure:
ui/Makefile.objs: delete unnecessary cocoa.o dependency
default-configs/: CONFIG_GDBSTUB_XML removed
Makefile.target: CONFIG_NO_* variables removed
rules.mak: New string testing functions
rules.mak: New logical functions for handling y/n values
rtl8139 has same problem as e1000, nic info isn't updated when macaddr
is changed in guest.
This patch updates the nic info when the last bit of macaddr is written.
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
If we change macaddr in guest by 'ifconfig eth0 hw ether 12:12:12:34:35:36',
the mac register of e1000 is already updated, but we don't update
network information in qemu. Therefor, the information in monitor
is wrong.
This patch updates nic info when the second part of macaddr is written.
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
macaddr is reset during device reset, but nic info
isn't updated, this problem exists in e1000 & rtl8139
Signed-off-by: Amos Kong <akong@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Report from valgrind:
==19521== Source and destination overlap in memcpy(0x31d38938, 0x31d38938, 64)
==19521== at 0x4A0A343: memcpy@@GLIBC_2.14 (in
/usr/lib64/valgrind/vgpreload_memcheck-amd64-linux.so)
==19521== by 0x42774E: virtio_blk_device_init (virtio-blk.c:686)
==19521== by 0x46EE9E: virtio_device_init (virtio.c:1158)
==19521== by 0x25405E: device_realize (qdev.c:178)
==19521== by 0x2559B5: device_set_realized (qdev.c:699)
==19521== by 0x3A819B: property_set_bool (object.c:1315)
==19521== by 0x3A6CE0: object_property_set (object.c:803)
Valgrind is right: blk == &s->blks, so it is a memcpy of 64 byte with
source == destination which can be removed.
Reported-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This allows to remove the explicit qemu_flush_coalesced_mmio_buffer
calls.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This allows to remove the explicit qemu_flush_coalesced_mmio_buffer
calls - the memory core will invoke them now.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We have a fw_cfg entry to pass e820 entries from qemu to the firmware.
Today it's used to pass reservations only. This patch makes qemu pass
entries for RAM too.
This allows to pass RAM sizes larger than 1TB to the firmware and it
will also allow to pass non-contignous memory ramges should we decide
to implement that some day, say for our virtual numa nodes.
Obviously this needs some extra care to not break existing firware.
SeaBIOS loads the entries and happily adds them without looking at the
type. Which is problematic for memory below 4g as this will overwrite
reservations added for bios memory etc. For memory above 4g it works
just fine, seabios will merge the entry derived from cmos with the one
loaded from fw_cfg.
OVMF doesn't look at the fw_cfg e820 table.
coreboot doesn't look at the fw_cfg e820 table.
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-By: Igor Mammedov <imammedo@redhat.com>
This patch fixes spice display initialization to handle
multihead properly.
spice-core now keeps track of which QemuConsole has a spice
display channel attached to it and which has not. It also
manages display channel ids.
spice-display looks at all QemuConsoles and will pick up any
graphic console not yet bound to a spice channel (which in practice
are all non-qxl graphic devices).
Result is that
(a) you'll get a spice client window for each graphical device
now (first only without this patch), and
(b) mixing qxl and non-qxl vga cards works properly.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Commit 4f8a066b5fc254eeaabbbde56ba4f5b29cc68fdf (blockdev: Remove IF_*
check for read-only blockdev_init) added a usage of bdrv_is_read_only()
to sd_init(), which is called for versatilepb, versatileab and
xilinx-zynq-a9 machines among others with NULL argument by default,
causing the new qom-test to fail.
Add a check to prevent this.
Suggested-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
CONFIG_NO_* variables replaced with the lnot logical function
Signed-off-by: Ákos Kovács <akoskovacs@gmx.com>
[PMM: fixed a few CONFIG_NO_* uses that were missed]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- Forgotten MSI affinity patch posted several months ago
- Lazy option ROM loading to delay load until after device/bus resets
- Error reporting cleanups
- PCI hot reset support introduced with Linux v3.12 development kernels
- Debug build fix for int128
The lazy ROM loading and hot reset should help VGA assignment as we can
now do a bus reset when there are multiple devices on the bus, ex.
multi-function graphics and audio cards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=SyvS
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'awilliam/tags/vfio-pci-for-qemu-20131010.0' into staging
vfio-pci updates include:
- Forgotten MSI affinity patch posted several months ago
- Lazy option ROM loading to delay load until after device/bus resets
- Error reporting cleanups
- PCI hot reset support introduced with Linux v3.12 development kernels
- Debug build fix for int128
The lazy ROM loading and hot reset should help VGA assignment as we can
now do a bus reset when there are multiple devices on the bus, ex.
multi-function graphics and audio cards.
# gpg: Signature made Thu 10 Oct 2013 11:26:39 AM PDT using RSA key ID 3BB08B22
# gpg: Can't check signature: public key not found
# By Alex Williamson (7) and Alexey Kardashevskiy (1)
# Via Alex Williamson
* awilliam/tags/vfio-pci-for-qemu-20131010.0:
vfio-pci: Fix endian issues in vfio_pci_size_rom()
vfio-pci: Add dummy PCI ROM write accessor
vfio: Fix debug output for int128 values
vfio-pci: Implement PCI hot reset
vfio-pci: Cleanup error_reports
vfio-pci: Lazy PCI option ROM loading
vfio-pci: Test device reset capabilities
vfio-pci: Add support for MSI affinity
Message-id: 20131010184122.31667.28382.stgit@bling.home
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
We don't really support CPU throttling, so supply 0 PBLK length.
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
