In hw/scsi/spapr_vio.c we declare that the controller supports multiple
buses by specifying "max_channel = 7" there. So in the code that fixes
up the device tree nodes, we must encode the channel number (a.k.a. bus
number in the "Logical unit addressing format" table of SAM5) into the
64-bit LUN, too.
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1663160
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
commit efe2add7cb ("spapr/vio: deprecate the "irq" property") was
merged in QEMU version 3.0. The "irq" property" can be removed for
QEMU version 4.0.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When reading base register of RAM slot with no RAM we should not try
to calculate register value because that will result printing an error
due to invalid RAM size. Just return 0 without the error in this case.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Fix the encoding of larger memory modules in the SoC registers which
allows specifying more than 1GB memory for sam460ex. Well, only 2GB
due to SoC and firmware restrictions which was the only missing value
compared to what the real hardware supports. The SoC should support up
to 4GB but when setting that the firmware hangs during memory test.
This may be an overflow bug in the firmware which I did not try to
debug but this may affect real hardware as well.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The sdram_set_bcr() function in ppc440_uc.c takes a pointer into an
array then calculates its index from that. It's simpler and easier to
just pass the index which simplifies both the function and its callers.
Do similar cleanup in ppc4xx_devs.c to similar function.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
There's already a struct with the same name in ppc4xx_devs.c. They are
not used outside their files so don't clash but they are also not
identical so rename the ppc440 specific one to distinguish them.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
To avoid overflow if larger values are added later use ram_addr_t for
the sdram_bank_sizes parameter to match ram_size to which it is compared.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Get rid of code from MIPS Malta board used to create SPD EEPROM data
(parts of which was not even needed for sam460ex) and use the generic
spd_data_generate() function to simplify this.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
There are several boards with SPD EEPROMs that are now using
duplicated or slightly different hard coded data. Add a helper to
generate SPD data for a memory module of given type and size that
could be used by these boards (either as is or with further changes if
needed) which should help cleaning this up and avoid further duplication.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
- vmdk: Support for blockdev-create
- block: Apply auto-read-only for ro-whitelist drivers
- virtio-scsi: Fixes related to attaching/detaching iothreads
- scsi-disk: Fixed erroneously detected multipath setup with multiple
disks created with node-names. Added device_id property.
- block: Fix hangs in synchronous APIs with iothreads
- block: Fix invalidate_cache error path for parent activation
- block-backend, mirror, qcow2, vpc, vdi, qemu-iotests:
Minor fixes and code improvements
-----BEGIN PGP SIGNATURE-----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=oaAn
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block layer patches:
- vmdk: Support for blockdev-create
- block: Apply auto-read-only for ro-whitelist drivers
- virtio-scsi: Fixes related to attaching/detaching iothreads
- scsi-disk: Fixed erroneously detected multipath setup with multiple
disks created with node-names. Added device_id property.
- block: Fix hangs in synchronous APIs with iothreads
- block: Fix invalidate_cache error path for parent activation
- block-backend, mirror, qcow2, vpc, vdi, qemu-iotests:
Minor fixes and code improvements
# gpg: Signature made Fri 01 Feb 2019 15:23:10 GMT
# gpg: using RSA key 7F09B272C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>" [full]
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* remotes/kevin/tags/for-upstream: (27 commits)
scsi-disk: Add device_id property
scsi-disk: Don't use empty string as device id
qtest.py: Wait for the result of qtest commands
block: Fix invalidate_cache error path for parent activation
iotests/236: fix transaction kwarg order
iotests: Filter second BLOCK_JOB_ERROR from 229
virtio-scsi: Forbid devices with different iothreads sharing a blockdev
scsi-disk: Acquire the AioContext in scsi_*_realize()
virtio-scsi: Move BlockBackend back to the main AioContext on unplug
block: Eliminate the S_1KiB, S_2KiB, ... macros
block: Remove blk_attach_dev_legacy() / legacy_dev code
block: Apply auto-read-only for ro-whitelist drivers
uuid: Make qemu_uuid_bswap() take and return a QemuUUID
block/vdi: Don't take address of fields in packed structs
block/vpc: Don't take address of fields in packed structs
vmdk: Reject excess extents in blockdev-create
iotests: Add VMDK tests for blockdev-create
iotests: Filter cid numbers in VMDK extent info
vmdk: Implement .bdrv_co_create callback
vmdk: Refactor vmdk_create_extent
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The nRF51 contains three regions of non-volatile memory (NVM):
- CODE (R/W): contains code
- FICR (R): Factory information like code size, chip id etc.
- UICR (R/W): Changeable configuration data. Lock bits, Code
protection configuration, Bootloader address, Nordic SoftRadio
configuration, Firmware configuration.
Read and write access to the memories is managed by the
Non-volatile memory controller.
Memory schema:
[ CPU ] -+- [ NVM, either FICR, UICR or CODE ]
| |
\- [ NVMC ]
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20190201023357.22596-2-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Until now, the set_pc logic was unclear, which raised questions about
whether it should be used directly, applying a value to PC or adding
additional checks, for example, set the Thumb bit in Arm cpu. Let's set
the set_pc logic for “Configure the PC, as was done in the ELF file”
and implement synchronize_with_tb hook for preserving PC to cpu_tb_exec.
Signed-off-by: Julia Suvorova <jusual@mail.ru>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190129121817.7109-1-jusual@mail.ru
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a model of the MPS2 FPGA image described in Application Note
AN521. This is identical to the AN505 image, except that it uses
the SSE-200 rather than the IoTKit and so has two Cortex-M33 CPUs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-24-peter.maydell@linaro.org
In preparation for adding support for the AN521 MPS2 image, we need
to handle wiring up the MPS2 device interrupt lines to both CPUs in
the SSE-200, rather than just the one that the IoTKit has.
Abstract out a "connect to the IoTKit interrupt line" function
and make it connect to a splitter which feeds both sets of inputs
for the SSE-200 case.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-23-peter.maydell@linaro.org
Add a model of the SSE-200, now we have put in all
the code that lets us make it different from the IoTKit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-22-peter.maydell@linaro.org
Instantiate a copy of the CPU_IDENTITY register block for each CPU
in an SSE-200.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-21-peter.maydell@linaro.org
The SSE-200 has a CPU_IDENTITY register block, which is a set of
read-only registers. As well as the usual PID/CID registers, there
is a single CPUID register which indicates whether the CPU is CPU 0
or CPU 1. Implement a model of this register block.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-20-peter.maydell@linaro.org
The SSE-200 has a "CPU local security control" register bank; add an
unimplemented-device stub for it. (The register bank has only one
interesting register, which allows the guest to lock down changes
to various CPU registers so they cannot be modified further. We
don't support that in our Cortex-M33 model anyway.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-19-peter.maydell@linaro.org
The SSE-200 gives each CPU a register bank to use to control its
L1 instruction cache. Put in an unimplemented-device stub for this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-18-peter.maydell@linaro.org
Add unimplemented-device stubs for the various Power Policy Unit
devices that the SSE-200 has.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-17-peter.maydell@linaro.org
The SSE-200 has two Message Handling Units (MHUs), which sit behind
the APB PPC0. Wire up some unimplemented-device stubs for these,
since we don't yet implement a real model of this device.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-16-peter.maydell@linaro.org
The SYS_VERSION and SYS_CONFIG register values differ between the
IoTKit and SSE-200. Make them configurable via QOM properties rather
than hard-coded, and set them appropriately in the ARMSSE code that
instantiates the IOTKIT_SYSINFO device.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-15-peter.maydell@linaro.org
Create a cluster object to hold each CPU in the SSE. They are
logically distinct and may be configured differently (for instance
one may not have an FPU where the other does).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-14-peter.maydell@linaro.org
Give each CPU its own container memory region. This is necessary
for two reasons:
* some devices are instantiated one per CPU and the CPU sees only
its own device
* since a memory region can only be put into one container, we must
give each armv7m object a different MemoryRegion as its 'memory'
property, or a dual-CPU configuration will assert on realize when
the second armv7m object tries to put the MR into a container when
it is already in the first armv7m object's container
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-13-peter.maydell@linaro.org
The SSE-200 has two Cortex-M33 CPUs. These see the same view
of memory, with the exception of the "private CPU region" which
has per-CPU devices. Internal device interrupts for SSE-200
devices are mostly wired up to both CPUs, with the exception of
a few per-CPU devices. External GPIO inputs on the SSE-200
device are provided for the second CPU's interrupts above 32,
as is already the case for the first CPU.
Refactor the code to support creation of multiple CPUs.
For the moment we leave all CPUs with the same view of
memory: this will not work in the multiple-CPU case, but
we will fix this in the following commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-12-peter.maydell@linaro.org
For the IoTKit the SRAM bank size is always 32K (15 bits); for the
SSE-200 this is a configurable parameter, which defaults to 32K but
can be changed when it is built into a particular SoC. For instance
the Musca-B1 board sets it to 128K (17 bits).
Make the bank size a QOM property. We follow the SSE-200 hardware in
naming the parameter SRAM_ADDR_WIDTH, which specifies the number of
address bits of a single SRAM bank.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-11-peter.maydell@linaro.org
The SSE-200 has four banks of SRAM, each with its own
Memory Protection Controller, where the IoTKit has only one.
Make the number of SRAM banks a field in ARMSSEInfo.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-10-peter.maydell@linaro.org
The SSE-200 has 4 banks of SRAM, each with its own internal
Memory Protection Controller. The interrupt status for these
extra MPCs appears in the same security controller SECMPCINTSTATUS
register as the MPC for the IoTKit's single SRAM bank. Enhance the
iotkit-secctl device to allow 4 MPCs. (If the particular IoTKit/SSE
variant in use does not have all 4 MPCs then the unused inputs will
simply result in the SECMPCINTSTATUS bits being zero as required.)
The hardcoded constant "1"s in armsse.c indicate the actual number
of SRAM MPCs the IoTKit has, and will be replaced in the following
commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-9-peter.maydell@linaro.org
Rename the files that used to be iotkit.[ch] to
armsse.[ch] to reflect the fact they new cover
multiple Arm subsystems for embedded.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-8-peter.maydell@linaro.org
Rename various internal uses of 'iotkit' in hw/arm/iotkit.c to
'armsse', for consistency. The remaining occurences are:
* related to the devices TYPE_IOTKIT_SYSCTL, TYPE_IOTKIT_SYSINFO,
etc, which this refactor is not touching
* references that apply specifically to the IoTKit (like
the lack of a private CPU region)
* the vmstate, which keeps its old "iotkit" name for
migration compatibility reasons
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-7-peter.maydell@linaro.org
The Arm SSE-200 Subsystem for Embedded is a revised and
extended version of the older IoTKit SoC. Prepare for
adding a model of it by refactoring the IoTKit code into
an abstract base class which contains the functionality,
driven by a class data block specific to each subclass.
(This is the same approach used by the existing bcm283x
SoC family implementation.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-6-peter.maydell@linaro.org
The Arm IoTKit was effectively the forerunner of a series of
subsystems for embedded SoCs, named the SSE-050, SSE-100 and SSE-200:
https://developer.arm.com/products/system-design/subsystems
These are generally quite similar, though later iterations have
extra devices that earlier ones do not.
We want to add a model of the SSE-200, which means refactoring the
IoTKit code into an abstract base class and subclasses (using the
same design that the bcm283x SoC and Aspeed SoC family
implementations do). As a first step, rename the IoTKit struct and
QOM macros to ARMSSE, which is what we're going to name the base
class. We temporarily retain TYPE_IOTKIT to avoid changing the
code that instantiates a TYPE_IOTKIT device here and then changing
it back again when it is re-introduced as a subclass.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-5-peter.maydell@linaro.org
Expose "start-powered-off" as a property of the ARMv7M container,
which we just pass through to the CPU object in the same way that we
do for "init-svtor" and "idau". (We want this for the SSE-200, which
powers up only the first CPU at reset and leaves the second powered
down.)
As with the other CPU properties here, we can't just use alias
properties, because the CPU QOM object is not created until armv7m
realize time.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-4-peter.maydell@linaro.org
Rather than just creating the CPUs with object_new, make them child
objects of the armv7m container. This will allow the cluster code to
find the CPUs if an armv7m object is made a child of a cluster object.
object_new_with_props() will do the parenting for us.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-3-peter.maydell@linaro.org
Currently the ARMv7M NVIC object's realize method assumes that the
CPU the NVIC is attached to is CPU 0, because it thinks there can
only ever be one CPU in the system. To allow a dual-Cortex-M33
setup we need to remove this assumption; instead the armv7m
wrapper object tells the NVIC its CPU, in the same way that it
already tells the CPU what the NVIC is.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-2-peter.maydell@linaro.org
set object owner in memory_region_init_ram() instead
of NULL.
Signed-off-by: kumar sourav <sourav.jb1988@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190125155630.17430-1-sourav.jb1988@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The new device_id property specifies which value to use for the vendor
specific designator in the Device Identification VPD page.
In particular, this is necessary for libvirt to maintain guest ABI
compatibility when no serial number is given and a VM is switched from
-drive (where the BlockBackend name is used) to -blockdev (where the
vendor specific designator is left out by default).
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
scsi-disk includes in the Device Identification VPD page, depending on
configuration amongst others, a vendor specific designator that consists
either of the serial number if given or the BlockBackend name (which is
a host detail that better shouldn't have been leaked to the guest, but
now we have to maintain it for compatibility).
With anonymous BlockBackends, i.e. scsi-disk devices constructed with
drive=<node-name>, and no serial number explicitly specified, this ends
up as an empty string. If this happens to more than one disk, we have
accidentally signalled to the OS that this is a multipath setup, which
is obviously not what was intended.
Instead of using an empty string for the vendor specific designator,
simply leave out that designator, which makes Linux detect such setups
as separate disks again.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
This patch forbids attaching a disk to a SCSI device if its using a
different AioContext. Test case included.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This fixes a crash when attaching two disks with the same blockdev to
a SCSI device that is using iothreads. Test case included.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This fixes a crash when attaching a disk to a SCSI device using
iothreads, then detaching it and reattaching it again. Test case
included.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Currently qemu_uuid_bswap() takes a pointer to the QemuUUID to
be byte-swapped. This means it can't be used when the UUID
to be swapped is in a packed member of a struct. It's also
out of line with the general bswap*() functions we provide
in bswap.h, which take the value to be swapped and return it.
Make qemu_uuid_bswap() take a QemuUUID and return the swapped version.
This fixes some clang warnings about taking the address of
a packed struct member in block/vdi.c.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Move the complexity of milkymist_tmu2_create() into the
source file. Doing so we avoid to include the X11/OpenGL
headers in all LM32 devices, and we also avoid the duplicate
declaration of glx_fbconfig_attr[] (it is already declared
in hw/display/milkymist-tmu2.c).
Since TYPE_MILKYMIST_TMU2 is now accessible, use it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190130120005.23123-5-philmd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The TMU device requires both X11 and OpenGL.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190130120005.23123-4-philmd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The Milkymist specific hardware is only used by the LM32 target,
it is pointless to compile those objects in other targets.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190130120005.23123-2-philmd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
- New debugging QMP command to explore block graphs
- Converted DPRINTF()s to trace events
- Fixed qemu-io's use of getopt() for systems with optreset
- Minor NVMe emulation fixes
- An iotest fix
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcUkaiAAoJEPQH2wBh1c9AHsEIAIU0+FNjtdz7lNgyeBCSFCFa
/qWNk4+w6QBfhTTx/N0hGwh5/FvNYQhby8VHtZitE4/QcLbJwHYgWf14pwce3tP3
3qNB87AdQpKMpbajQM2x2Xy8lnlPeM7fe21Q/12vuX7AlEDT3gH+W9rg94bw2oFN
r+xBk6H5F2aVElw3CwMM7eary4+dPnnCQwAnoqM+g5hdpL+0scrIyARGw7v0hmSn
LDWESCM4a55lEYmwj1wS3J3uj6Fj00yzBvcEuCcT1GO+lXlV8/ciO9r2HqxVKwgz
4GAi/BERoMKjfn+/77/yI5flprPx2voNGgkyBY4C3z9ncnN6u02QBZSusBIWpSg=
=Kt4r
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/xanclic/tags/pull-block-2019-01-31' into staging
Block patches:
- New debugging QMP command to explore block graphs
- Converted DPRINTF()s to trace events
- Fixed qemu-io's use of getopt() for systems with optreset
- Minor NVMe emulation fixes
- An iotest fix
# gpg: Signature made Thu 31 Jan 2019 00:51:46 GMT
# gpg: using RSA key F407DB0061D5CF40
# gpg: Good signature from "Max Reitz <mreitz@redhat.com>" [full]
# Primary key fingerprint: 91BE B60A 30DB 3E88 57D1 1829 F407 DB00 61D5 CF40
* remotes/xanclic/tags/pull-block-2019-01-31:
iotests: Allow 147 to be run concurrently
iotests: Bind qemu-nbd to localhost in 147
iotests.py: Add qemu_nbd_pipe()
nvme: use pci_dev directly in nvme_realize
nvme: ensure the num_queues is not zero
nvme: use TYPE_NVME instead of constant string
qemu-io: Add generic function for reinitializing optind.
block/sheepdog: Convert from DPRINTF() macro to trace events
block/file-posix: Convert from DPRINTF() macro to trace events
block/curl: Convert from DPRINTF() macro to trace events
block/ssh: Convert from DPRINTF() macro to trace events
scripts: add render_block_graph function for QEMUMachine
qapi: add x-debug-query-block-graph
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
