This patch adds support for split IRQ chip mode. When
KVM_CAP_SPLIT_IRQCHIP is enabled:
1.) The PIC, PIT, and IOAPIC are implemented in userspace while
the LAPIC is implemented by KVM.
2.) The software IOAPIC delivers interrupts to the KVM LAPIC via
kvm_set_irq. Interrupt delivery is configured via the MSI routing
table, for which routes are reserved in target-i386/kvm.c then
configured in hw/intc/ioapic.c
3.) KVM delivers IOAPIC EOIs via a new exit KVM_EXIT_IOAPIC_EOI,
which is handled in target-i386/kvm.c and relayed to the software
IOAPIC via ioapic_eoi_broadcast.
Signed-off-by: Matt Gingell <gingell@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The ioeventfd mechanism is used by vhost, dataplane, and virtio-pci to
turn guest MMIO/PIO writes into eventfd file descriptor events. This
allows arbitrary threads to be notified when the guest writes to a
specific MMIO/PIO address.
qtest and TCG do not support ioeventfd because memory writes are not
checked against registered ioeventfds in QEMU. This patch implements
this in memory_region_dispatch_write() so qtest can use ioeventfd.
Also this patch fixes vhost aborting on some misconfigured old kernels
like 3.18.0 on ARM. It is possible to explicitly enable CONFIG_EVENTFD
in expert settings, while MMIO binding support in KVM will still be
missing.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Message-Id: <006e01d12377$0b9c2d40$22d487c0$@samsung.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Just noticed this while grepping TARGET_PAGE_SIZE for an unrelated
reason. I didn't use qemu_real_host_page_size as kvm_set_phys_mem()
does, because we'd need to make sure page_size_init() has run first.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-Id: <1447115022-4142-1-git-send-email-drjones@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
The HOST_PAGE_ALIGN macros don't work until the page size variables
have been set up; later in postcopy I use those macros in the RAM
code, and it can be triggered using -object.
Fix this by initialising page_size_init() earlier - it's currently
initialised inside the accelerators, move it up into vl.c.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
This reverts commit de9d61e83d.
Now 'cpu_clean_all_dirty' is useless, we can revert the related code.
Conflicts:
include/sysemu/kvm.h
Signed-off-by: Liang Li <liang.z.li@intel.com>
Message-Id: <1446695464-27116-3-git-send-email-liang.z.li@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The functions for checking xcrs, xsave and pit_state2 are
only used on x86, so they should reside in target-i386/kvm.c.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1444933820-6968-1-git-send-email-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In-kernel ITS emulation on ARM64 will require to supply requester IDs.
These IDs can now be retrieved from the device pointer using new
pci_requester_id() function.
This patch adds pci_dev pointer to KVM GSI routing functions and makes
callers passing it.
x86 architecture does not use requester IDs, but hw/i386/kvm/pci-assign.c
also made passing PCI device pointer instead of NULL for consistency with
the rest of the code.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Message-Id: <ce081423ba2394a4efc30f30708fca07656bc500.1444916432.git.p.fedin@samsung.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This capability is useful to determine whether we can use KVM ITS
emulation on ARM
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Message-Id: <ff4ccb09b837d37defd639b885526949a25276de.1444916432.git.p.fedin@samsung.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As the comment in kvm_set_phys_mem() says, KVM works in page size chunks.
However it uses hardcoded TARGET_PAGE_SIZE which is 4K on most platforms
while actual host may use different page size, for example, PPC64 hosts
use 64K system pages.
This replaces static TARGET_PAGE_SIZE with run-time calculated
qemu_real_host_page_size.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <1444102257-17405-1-git-send-email-aik@ozlabs.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some functions previously used only by vGICv2 are useful also for vGICv3
implementation. Untie them from GICState and make accessible from within
other modules:
- kvm_arm_gic_set_irq()
- kvm_gic_supports_attr() - moved to common code and renamed to
kvm_device_check_attr()
- kvm_gic_access() - turned into GIC-independent kvm_device_access().
Data pointer changed to void * because some GICv3 registers are
64-bit wide
Some of these changes are not used right now, but they will be helpful for
implementing live migration.
Actually kvm_dist_get() and kvm_dist_put() could also be made reusable, but
they would require two extra parameters (s->dev_fd and s->num_cpu) as well as
lots of typecasts of 's' to DeviceState * and back to GICState *. This makes
the code very ugly so i decided to stop at this point. I tried also an
approach with making a base class for all possible GICs, but it would contain
only three variables (dev_fd, cpu_num and irq_num), and accessing them through
the rest of the code would be again tedious (either ugly casts or qemu-style
separate object pointer). So i disliked it too.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Tested-by: Ashok kumar <ashoks@broadcom.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 2ef56d1dd64ffb75ed02a10dcdaf605e5b8ff4f8.1441784344.git.p.fedin@samsung.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
KVM kernel can send guest crash events into userspace.
Appropriate guest crash handler is called when kernel guest
crash event received. Guest crash event recognized by a
KVM_SYSTEM_EVENT_CRASH type of system event.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Andreas Färber <afaerber@suse.de>
Message-Id: <1435924905-8926-11-git-send-email-den@openvz.org>
[Rebase: add lock/unlock iothread around qemu_system_guest_panicked - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When we add new adapter routes we call kvm_irqchip_add_route() for every
virtqueue and in the same step also do the KVM_SET_GSI_ROUTING ioctl.
This is unnecessary costly as the interface allows us to set multiple
routes in one go. Let's first add all routes to the table stored in the
global kvm_state and then do the ioctl to commit the routes to the
in-kernel irqchip.
This saves us several ioctls to the kernel where for each call a list
is reallocated and populated.
Signed-off-by: Jens Freimann <jfrei@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
VFIO platform device needs to setup irqfd but it does not know the
gsi corresponding to the device qemu_irq. This patch proposes to
store a hash table in kvm_state using the qemu_irq as key and the gsi
as a value.
kvm_irqchip_set_qemuirq_gsi allows to insert such a pair. The interrupt
controller is supposed to use it.
kvm_irqchip_[add, remove]_irqfd_notifier allows to setup/tear down
irqfd directly from the qemu_irq.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Tested-by: Vikram Sethi <vikrams@codeaurora.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Anticipating for the introduction of new add/remove functions taking
a qemu_irq parameter, let's rename existing ones with a gsi suffix.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Tested-by: Vikram Sethi <vikrams@codeaurora.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
KVM_CREATE_IRQCHIP should never fail, and so should its userspace
wrapper kvm_irqchip_create. The function does not do anything
if the irqchip capability is not available, as is the case for PPC.
With this patch, kvm_arch_init can allocate memory and it will not
be leaked.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make kvm_memory_listener_register public, and assign a kernel
address space id to each KVMMemoryListener.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
No semantic change, but s->slots moves into a new struct
KVMMemoryListener. KVM's memory listener becomes a member of struct
KVMState, and becomes of type KVMMemoryListener.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
i386 code will have to define a different KVMMemoryListener. Create
an internal header so that KVMSlot is not exposed outside.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently kvm_mem_flags just translates bools to bits, let's
make it also determine the bools first. This avoids its parameter
list growing each time we add a flag.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Do not take the BQL before dispatching MMIO requests of KVM VCPUs.
Instead, address_space_rw will do it if necessary. This enables completely
BQL-free MMIO handling in KVM mode for upcoming devices with fine-grained
locking.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1434646046-27150-10-git-send-email-pbonzini@redhat.com>
Do not take the BQL before dispatching PIO requests of KVM VCPUs.
Instead, address_space_rw will do it if necessary. This enables
completely BQL-free PIO handling in KVM mode for upcoming devices with
fine-grained locking.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1434646046-27150-8-git-send-email-pbonzini@redhat.com>
This opens the path to get rid of the iothread lock on vmexits in KVM
mode. On x86, the in-kernel irqchips has to be used because we otherwise
need to synchronize APIC and other per-cpu state accesses that could be
changed concurrently.
Regarding pre/post-run callbacks, s390x and ARM should be fine without
specific locking as the callbacks are empty. MIPS and POWER require
locking for the pre-run callback.
For the handle_exit callback, it is non-empty in x86, POWER and s390.
Some POWER cases could do without the locking, but it is left in
place for now.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1434646046-27150-7-git-send-email-pbonzini@redhat.com>
Last month, we experienced several guests crash(6cores-8cores), qemu logs
display the following messages:
qemu-system-x86_64: /build/qemu-2.1.2/kvm-all.c:976:
kvm_irqchip_commit_routes: Assertion `ret == 0' failed.
After analysis and verification, we can confirm it's irq-balance
daemon(in guest) leads to the assertion failure. Start a 8 core guest with
two disks, execute the following scripts will reproduce the BUG quickly:
irq_affinity.sh
========================================================================
vda_irq_num=25
vdb_irq_num=27
while [ 1 ]
do
for irq in {1,2,4,8,10,20,40,80}
do
echo $irq > /proc/irq/$vda_irq_num/smp_affinity
echo $irq > /proc/irq/$vdb_irq_num/smp_affinity
dd if=/dev/vda of=/dev/zero bs=4K count=100 iflag=direct
dd if=/dev/vdb of=/dev/zero bs=4K count=100 iflag=direct
done
done
========================================================================
QEMU setup static irq route entries in kvm_pc_setup_irq_routing(), PIC and
IOAPIC share the first 15 GSI numbers, take up 23 GSI numbers, but take up
38 irq route entries. When change irq smp_affinity in guest, a dynamic route
entry may be setup, the current logic is: if allocate GSI number succeeds,
a new route entry can be added. The available dynamic GSI numbers is
1021(KVM_MAX_IRQ_ROUTES-23), but available irq route entries is only
986(KVM_MAX_IRQ_ROUTES-38), GSI numbers greater than route entries.
irq-balance's behavior will eventually leads to total irq route entries
exceed KVM_MAX_IRQ_ROUTES, ioctl(KVM_SET_GSI_ROUTING) fail and
kvm_irqchip_commit_routes() trigger assertion failure.
This patch fix the BUG.
Signed-off-by: Wenshuang Ma <kevinnma@tencent.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
One recent example is commit 4cc856f (kvm-all: Sync dirty-bitmap from
kvm before kvm destroy the corresponding dirty_bitmap, 2015-04-02).
Another performance problem is that KVM keeps tracking dirty pages
after a failed live migration, which causes bad performance due to
disallowing huge page mapping.
Thanks to the previous patch, KVM can now stop hooking into
log_global_start/stop. This simplifies the KVM code noticeably.
Reported-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Reported-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It is okay if memory is not mapped into the guest but has dirty logging
enabled. When this happens, KVM will not do anything and only accesses
from the host will be logged.
This can be triggered by iofuzz.
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When the dirty log mask will also cover other bits than DIRTY_MEMORY_VGA,
some listeners may be interested in the overall zero/non-zero value of
the dirty log mask; others may be interested in the value of single bits.
For this reason, always call log_start/log_stop if bits have respectively
appeared or disappeared, and pass the old and new values of the dirty log
mask so that listeners can distinguish the kinds of change.
For example, KVM checks if dirty logging used to be completely disabled
(in log_start) or is now completely disabled (in log_stop). On the
other hand, Xen has to check manually if DIRTY_MEMORY_VGA changed,
since that is the only bit it cares about.
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For now memory regions only track DIRTY_MEMORY_VGA individually, but
this will change soon. To support this, split memory_region_is_logging
in two functions: one that returns a given bit from dirty_log_mask,
and one that returns the entire mask. memory_region_is_logging gets an
extra parameter so that the compiler flags misuse.
While VGA-specific users (including the Xen listener!) will want to keep
checking that bit, KVM and vhost check for "any bit except migration"
(because migration is handled via the global start/stop listener
callbacks).
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
On POWER8 systems, KVM checks if VCPU is running on primary threads,
and that secondary threads are offline. If this is not the case,
ioctl() fails with errno set to EBUSY.
QEMU aborts with a non explicit error message:
$ ./qemu-system-ppc64 --nographic -machine pseries,accel=kvm
error: kvm run failed Device or resource busy
To help user to diagnose the problem, this patch adds an informative
error message.
There is no easy way to check if SMT is enabled before starting the VCPU,
and as this case is the only one setting errno to EBUSY, we just check
the errno value to display a message.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <1431976007-20503-1-git-send-email-lvivier@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
On ARM the MSI data corresponds to the shared peripheral interrupt (SPI)
ID. This latter equals to the SPI index + 32. to retrieve the SPI index,
matching the gsi, an architecture specific function is introduced.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let kvm_arch_post_run convert fields in the kvm_run struct to MemTxAttrs.
These are then passed to address_space_rw.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
valgrind complains here about uninitialized bytes with the following message:
==17814== Syscall param ioctl(generic) points to uninitialised byte(s)
==17814== at 0x466A780: ioctl (in /usr/lib64/power8/libc-2.17.so)
==17814== by 0x100735B7: kvm_vm_ioctl (kvm-all.c:1920)
==17814== by 0x10074583: kvm_set_ioeventfd_mmio (kvm-all.c:574)
Let's fix it by using a proper struct initializer in kvm_set_ioeventfd_mmio().
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1430153944-24368-1-git-send-email-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If KVM_CREATE failed on s390x, we print a hint to enable the switch_amode
kernel parameter. This only applies to old kernels, and only if the
error was -EINVAL. Moreover, with new kernels, the most likely reason
for -EINVAL is that pgstes were not enabled.
Let's update the error message to give a better hint on where things
may need fixing.
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
There are a number of ffs(3) callers that do roughly:
bit = ffs(val);
if (bit) {
do_something(bit - 1);
}
This pattern can be converted to ctz32() like this:
zeroes = ctz32(val);
if (zeroes != 32) {
do_something(zeroes);
}
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1427124571-28598-6-git-send-email-stefanha@redhat.com
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Make address_space_rw take transaction attributes, rather
than always using the 'unspecified' attributes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Sometimes, we destroy the dirty_bitmap in kvm_memory_slot before any sync action
occur, this bit in dirty_bitmap will be missed, and which will lead the corresponding
dirty pages to be missed in migration.
This usually happens when do migration during VM's Start-up or Reboot.
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
[Use s->migration_log instead of exec.c's in_migration. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM expects host endian values. Hosts that don't use the default endianness
need to negate the swap performed in adjust_endianness().
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Message-Id: <20150313212337.31142.3991.stgit@bahia.local>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
More and more virtual machine specifics between kvm and qemu will be
transferred with vm attributes.
So we encapsulate the common logic in a generic function.
Additionally we need only to check during initialization if kvm supports
virtual machine attributes.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Suggested-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Signed-off-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Signed-off-by: Jens Freimann <jfrei@linux.vnet.ibm.com>
Message-Id: <1426164834-38648-2-git-send-email-jfrei@linux.vnet.ibm.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Needed to query machine's properties.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Running
x86_64-softmmu/qemu-system-x86_64 -machine pc,kernel_irqchip=on -enable-kvm
leads to crash:
qemu-system-x86_64: qemu/util/qemu-option.c:387: qemu_opt_get_bool_helper:
Assertion `opt->desc && opt->desc->type == QEMU_OPT_BOOL' failed. Aborted
(core dumped)
This happens because the commit e79d5a6 ("machine: remove qemu_machine_opts
global list") removed the global option descriptions and moved them to
MachineState's QOM properties.
Fix this by querying machine properties through designated wrappers.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
man gcc:
Warn about logical not used on the left hand side operand of a
comparison. This option does not warn if the RHS operand is of a
boolean type.
By preferring bool over int where sensible, but without modifying any
depending code, make GCC happy in cases like this,
qemu-img.c: In function ‘compare_sectors’:
qemu-img.c:992:39: error: logical not is only applied to the left hand
side of comparison [-Werror=logical-not-parentheses]
if (!!memcmp(buf1, buf2, 512) != res) {
hw/ide/core.c:1836 doesn't throw an error,
assert(!!s->error == !!(s->status & ERR_STAT));
even thought the second operand is int (and first hunk of this patch has
a very similar case), maybe GCC developers still have a little faith in
C programmers.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
on s390 MSI-X irqs are presented as thin or adapter interrupts
for this we have to reorganize the routing entry to contain
valid information for the adapter interrupt code on s390.
To minimize impact on existing code we introduce an architecture
function to fixup the routing entry.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Paolo Bonzini reported that Coverity reports an uninitialized pad value.
Let's use a designated initializer for kvm_irq_routing_entry to avoid
this false positive. This is similar to kvm_irqchip_add_msi_route and
other users of kvm_irq_routing_entry.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
struct kvm_dirty_log contains padding fields that trigger false
positives in valgrind. Let's use a designated initializer to avoid
false positives from valgrind/memcheck.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Compute kvm_irqfds_allowed by checking the KVM_CAP_IRQFD extension.
Remove direct settings in architecture specific files.
Add a new kvm_resamplefds_allowed variable, initialized by
checking the KVM_CAP_IRQFD_RESAMPLE extension. Add a corresponding
kvm_resamplefds_enabled() function.
A special notice for s390 where KVM_CAP_IRQFD was not immediatly
advirtised when irqfd capability was introduced in the kernel.
KVM_CAP_IRQ_ROUTING was advertised instead.
This was fixed in "KVM: s390: announce irqfd capability",
ebc3226202d5956a5963185222982d435378b899 whereas irqfd support
was brought in 84223598778ba08041f4297fda485df83414d57e,
"KVM: s390: irq routing for adapter interrupts". Both commits
first appear in 3.15 so there should not be any kernel
version impacted by this QEMU modification.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When more memory devices are used than available
KVM memory slots, QEMU crashes with:
kvm_alloc_slot: no free slot available
Aborted (core dumped)
Fix this by checking that KVM has a free slot before
attempting to map memory in guest address space.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
