When DT node names for PCI devices are generated by SLOF,
they are generated according to the type of the device
(for instance, ethernet for virtio-net-pci device).
Node name for hotplugged devices is generated by QEMU.
This patch adds the mechanic to QEMU to create the node
name according to the device type too.
The data structure has been roughly copied from OpenBIOS/OpenHackware,
node names from SLOF.
Example:
Hotplugging some PCI cards with QEMU monitor:
device_add virtio-tablet-pci
device_add virtio-serial-pci
device_add virtio-mouse-pci
device_add virtio-scsi-pci
device_add virtio-gpu-pci
device_add ne2k_pci
device_add nec-usb-xhci
device_add intel-hda
What we can see in linux device tree:
for dir in /proc/device-tree/pci@800000020000000/*@*/; do
echo $dir
cat $dir/name
echo
done
WITHOUT this patch:
/proc/device-tree/pci@800000020000000/pci@0/
pci
/proc/device-tree/pci@800000020000000/pci@1/
pci
/proc/device-tree/pci@800000020000000/pci@2/
pci
/proc/device-tree/pci@800000020000000/pci@3/
pci
/proc/device-tree/pci@800000020000000/pci@4/
pci
/proc/device-tree/pci@800000020000000/pci@5/
pci
/proc/device-tree/pci@800000020000000/pci@6/
pci
/proc/device-tree/pci@800000020000000/pci@7/
pci
WITH this patch:
/proc/device-tree/pci@800000020000000/communication-controller@1/
communication-controller
/proc/device-tree/pci@800000020000000/display@4/
display
/proc/device-tree/pci@800000020000000/ethernet@5/
ethernet
/proc/device-tree/pci@800000020000000/input-controller@0/
input-controller
/proc/device-tree/pci@800000020000000/mouse@2/
mouse
/proc/device-tree/pci@800000020000000/multimedia-device@7/
multimedia-device
/proc/device-tree/pci@800000020000000/scsi@3/
scsi
/proc/device-tree/pci@800000020000000/usb-xhci@6/
usb-xhci
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This finally allows TCG to benefit from the iothread introduction: Drop
the global mutex while running pure TCG CPU code. Reacquire the lock
when entering MMIO or PIO emulation, or when leaving the TCG loop.
We have to revert a few optimization for the current TCG threading
model, namely kicking the TCG thread in qemu_mutex_lock_iothread and not
kicking it in qemu_cpu_kick. We also need to disable RAM block
reordering until we have a more efficient locking mechanism at hand.
Still, a Linux x86 UP guest and my Musicpal ARM model boot fine here.
These numbers demonstrate where we gain something:
20338 jan 20 0 331m 75m 6904 R 99 0.9 0:50.95 qemu-system-arm
20337 jan 20 0 331m 75m 6904 S 20 0.9 0:26.50 qemu-system-arm
The guest CPU was fully loaded, but the iothread could still run mostly
independent on a second core. Without the patch we don't get beyond
32206 jan 20 0 330m 73m 7036 R 82 0.9 1:06.00 qemu-system-arm
32204 jan 20 0 330m 73m 7036 S 21 0.9 0:17.03 qemu-system-arm
We don't benefit significantly, though, when the guest is not fully
loading a host CPU.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Message-Id: <1439220437-23957-10-git-send-email-fred.konrad@greensocs.com>
[FK: Rebase, fix qemu_devices_reset deadlock, rm address_space_* mutex]
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
[EGC: fixed iothread lock for cpu-exec IRQ handling]
Signed-off-by: Emilio G. Cota <cota@braap.org>
[AJB: -smp single-threaded fix, clean commit msg, BQL fixes]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Pranith Kumar <bobby.prani@gmail.com>
[PM: target-arm changes]
Acked-by: Peter Maydell <peter.maydell@linaro.org>
When performing clock calculations, the ppc405_uc code
has several places where it multiplies together two
32-bit variables and assigns the result to a 64-bit
variable. This doesn't quite do what is intended because
C will compute a 32-bit multiply result. Add casts to
ensure we don't truncate the result.
(Spotted by Coverity, CID 1005504, 1005505.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On POWER, the valid page sizes that the guest can use are bound
to the CPU and not to the memory region. QEMU already has some
fancy logic to find out the right maximum memory size to tell
it to the guest during boot (see getrampagesize() in the file
target/ppc/kvm.c for more information).
However, once we're booted and the guest is using huge pages
already, it is currently still possible to hot-plug memory regions
that does not support huge pages - which of course does not work
on POWER, since the guest thinks that it is possible to use huge
pages everywhere. The KVM_RUN ioctl will then abort with -EFAULT,
QEMU spills out a not very helpful error message together with
a register dump and the user is annoyed that the VM unexpectedly
died.
To avoid this situation, we should check the page size of hot-plugged
DIMMs to see whether it is possible to use it in the current VM.
If it does not fit, we can print out a better error message and
refuse to add it, so that the VM does not die unexpectely and the
user has a second chance to plug a DIMM with a matching memory
backend instead.
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1419466
Signed-off-by: Thomas Huth <thuth@redhat.com>
[dwg: Fix a build error on 32-bit builds with KVM]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Generic helper machine_query_hotpluggable_cpus() replaced
target specific query_hotpluggable_cpus() callbacks so
there is no need in it anymore. However inon NULL callback
value is used to detect/report hotpluggable cpus support,
therefore it can be removed completely.
Replace it with MachineClass.has_hotpluggable_cpus boolean
which is sufficient for the task.
Suggested-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
All callbacks FOO_query_hotpluggable_cpus() are practically
the same except of setting vcpus_count to different values.
Convert them to a generic machine_query_hotpluggable_cpus()
callback by moving vcpus_count initialization to per machine
specific callback possible_cpu_arch_ids().
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Replace SPAPR specific cores[] array with generic
machine->possible_cpus and store core objects there.
It makes cores bookkeeping similar to x86 cpus and
will allow to unify similar code.
It would allow to replace cpu_index based NUMA node
mapping with iproperty based one (for -device created
cores) since possible_cpus carries board defined
topology/layout.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The last byte of the option vector was missing due to an off-by-one
error. Without this fix, client architecture support negotiation will
fail because the last byte of option vector 5, which contains the MMU
support, will be missed.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
error_report() already puts a prefix with the program name in front
of the error strings, so the "qemu:" prefix is not necessary here
anymore.
Reported-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr_core_unplug() were essentially spapr_core_unplug_request()
handler that requested CPU removal and registered callback
which did actual cpu core removali but it was called from
spapr_machine_device_unplug() which is intended for actual object
removal. Commit (cf632463 spapr: Memory hot-unplug support)
sort of fixed it introducing spapr_machine_device_unplug_request()
and calling spapr_core_unplug() but it hasn't renamed callback and
by mistake calls it from spapr_machine_device_unplug().
However spapr_machine_device_unplug() isn't ever called for
cpu core since spapr_core_release() doesn't follow expected
hotunplug call flow which is:
1: device_del() ->
hotplug_handler_unplug_request() ->
set destroy_cb()
2: destroy_cb() ->
hotplug_handler_unplug() ->
object_unparent // actual device removal
Fix it by renaming spapr_core_unplug() to spapr_core_unplug_request()
which is called from spapr_machine_device_unplug_request() and
making spapr_core_release() call hotplug_handler_unplug() which
will call spapr_machine_device_unplug() -> spapr_core_unplug()
to remove cpu core.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reveiwed-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr_core_pre_plug/spapr_core_plug/spapr_core_unplug() are managing
wiring CPU core into spapr machine state and not internal CPU core state.
So move them from spapr_cpu_core.c to spapr.c where other similar
(spapr_memory_[foo]plug()) callbacks are located, which also matches
x86 target practice.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Split off destroying VCPU threads from drc callback
spapr_core_release() into new spapr_cpu_core_unrealizefn()
which takes care of internal cpu core state cleanup (i.e.
VCPU threads) and is called when object_unparent(core)
is called.
That leaves spapr_core_release() only with board mgmt
code, which will be moved to board related file in
follow up patch along with the rest on hotplug callbacks.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Block backends defined with -drive if=ide are meant to be picked up by
machine initialization code: a suitable frontend gets created and
wired up automatically.
if=ide drives not picked up that way can still be used with -device as
if they had if=none, but that's unclean and best avoided. Unused ones
produce an "Orphaned drive without device" warning.
-drive parameter "if" is optional, and the default depends on the
machine type. If a machine type doesn't specify a default, the
default is "ide".
Many machine types default to if=ide, even though they don't actually
have an IDE controller. A future patch will change these defaults to
something more sensible. To prepare for it, this patch makes default
"ide" explicit for the machines that actually pick up if=ide drives:
* alpha: clipper
* arm/aarch64: spitz borzoi terrier tosa
* i386/x86_64: generic-pc-machine (with concrete subtypes pc-q35-*
pc-i440fx-* pc-* isapc xenfv)
* mips64el: fulong2e
* mips/mipsel/mips64el: malta mips
* ppc/ppc64: mac99 g3beige prep
* sh4/sh4eb: r2d
* sparc64: sun4u sun4v
Note that ppc64 machine powernv already sets an "ide" default
explicitly. Its IDE controller isn't implemented, yet.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1487153147-11530-2-git-send-email-armbru@redhat.com>
it's not very convenient to use the crash-information property interface,
so provide a CPU class callback to get the guest crash information, and pass
that information in the event
Signed-off-by: Anton Nefedov <anton.nefedov@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Message-Id: <1487053524-18674-3-git-send-email-den@openvz.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
hw_error() is for CPU related errors only (it dumps the CPU registers
and calls abort()!), so using error_report() is the better choice
of reporting an error in case we simply did not find a file.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Machines bamboo, e500 and virtex-ml507 assume a certain MMU model,
otherwise resulting in unpredictable behavior. Add apropriate checks
into *_init functions.
Signed-off-by: Valentin Plotkin <caliborn@sdf.org>
[regarding virtex parts]
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We are switching BUILD_BUG_ON to verify that it's parameter is a
compile-time constant, and it turns out that some gcc versions
(specifically gcc (Ubuntu 5.4.0-6ubuntu1~16.04.4) 5.4.0 20160609) are
not smart enough to figure it out for expressions involving local
variables. This is harmless but means that the check is ineffective for
these platforms. To fix, replace the variable with macros.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
[dwg: Correct a printf format warning]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is a port to ppc of the i386 commit:
00f4d64 kvmclock: clock should count only if vm is running
We remove timebase_post_load function, and use the VM state
change handler to save and restore the guest_timebase (on stop
and continue).
We keep timebase_pre_save to reduce the clock difference on
migration like in:
6053a86 kvmclock: reduce kvmclock difference on migration
Time base offset has originally been introduced by commit
98a8b52 spapr: Add support for time base offset migration
So while VM is paused, the time is stopped. This allows to have
the same result with date (based on Time Base Register) and
hwclock (based on "get-time-of-day" RTAS call).
Moreover in TCG mode, the Time Base is always paused, so this
patch also adjust the behavior between TCG and KVM.
VM state field "time_of_the_day_ns" is now useless but we keep
it to be able to migrate to older version of the machine.
As vmstate_ppc_timebase structure (with timebase_pre_save() and
timebase_post_load() functions) was only used by vmstate_spapr,
we register the VM state change handler only in ppc_spapr_init().
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It is completely unused, thus it can be removed without problems.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
If the DECAR register is set to 0, QEMU tries to reload the decrementer with
zero in an inifinite loop. According to PPC documentation, the decrementer is
triggered on 1->0 transition, so avoid reloading the decrementer if if is
already zero.
The problem does not manifest under Linux, but it is valid to set DECAR to zero
(and may make sense as part of decrementer initialization when interrupts are
disabled).
Signed-off-by: Roman Kapl <rka@sysgo.com>
[dwg: Fixed style nit]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Once a compatiblity mode is negotiated with the guest,
h_client_architecture_support() uses run_on_cpu() to update each CPU to
the new mode. We're going to want this logic somewhere else shortly,
so make a helper function to do this global update.
We put it in target-ppc/compat.c - it makes as much sense at the CPU level
as it does at the machine level. We also move the cpu_synchronize_state()
into ppc_set_compat(), since it doesn't really make any sense to call that
without synchronizing state.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
During boot, PAPR guests negotiate CPU model support with the
ibm,client-architecture-support mechanism. The logic to implement this in
qemu is very convoluted. This cleans it up to be cleaner, using the new
ppc_check_compat() call.
The new logic for choosing a compatibility mode is:
1. Usually, use the most recent compatibility mode that is
a) supported by the guest
b) supported by the CPU
and c) no later than the maximum allowed (if specified)
2. If no suitable compatibility mode was found, the guest *does*
support this CPU explicitly, and no maximum compatibility mode is
specified, then use "raw" mode for the current CPU
3. Otherwise, fail the boot.
This differs from the results of the old code: the old code preferred using
"raw" mode to a compatibility mode, whereas the new code prefers a
compatibility mode if available. Using compatibility mode preferentially
means that we're more likely to be able to migrate the guest to a similar
but not identical host.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Machine supports both Open Hack'Ware and OpenBIOS.
Open Hack'Ware is the default because OpenBIOS is currently unable to boot
PReP boot partitions or PReP kernels.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
[dwg: Correct compile failure with KVM located by Thomas Huth]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[dwg: Added CONFIG_RS6000_MC to ppc64 or it breaks testcases]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This device is a partial duplicate of System I/O device available in hw/ppc/prep.c
This new one doesn't have all the Motorola-specific registers.
The old one should be deprecated and removed with the 'prep' machine.
Partial documentation available at
ftp://ftp.software.ibm.com/rs6000/technology/spec/srp1_1.exe
section 6.1.5 (I/O Device Mapping)
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
To continue consolidation of compatibility mode information, this rewrites
the ppc_get_compat_smt_threads() function using the table of compatiblity
modes in target-ppc/compat.c.
It's not a direct replacement, the new ppc_compat_max_threads() function
has simpler semantics - it just returns the number of threads the cpu
model has, taking into account any compatiblity mode it is in.
This no longer takes into account kvmppc_smt_threads() as the previous
version did. That check wasn't useful because we check in
ppc_cpu_realizefn() that CPUs aren't instantiated with more threads
than kvm allows (or if we didn't things will already be broken and
this won't make it any worse).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
When passing through an USB storage device to a pseries guest, it
is currently not possible to automatically boot from the device
if the "bootindex" property has been specified, too (e.g. when using
"-device nec-usb-xhci -device usb-host,hostbus=1,hostaddr=2,bootindex=0"
at the command line). The problem is that QEMU builds a device tree path
like "/pci@800000020000000/usb@0/usb-host@1" and passes it to SLOF
in the /chosen/qemu,boot-list property. SLOF, however, probes the
USB device, recognizes that it is a storage device and thus changes
its name to "storage", and additionally adds a child node for the
SCSI LUN, so the correct boot path in SLOF is something like
"/pci@800000020000000/usb@0/storage@1/disk@101000000000000" instead.
So when we detect an USB mass storage device with SCSI interface,
we've got to adjust the firmware boot-device path properly that
SLOF can automatically boot from the device.
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1354177
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The H_SIGNAL_SYS_RESET hcall allows a guest CPU to raise a system reset
exception on CPUs within the same guest -- all CPUs, all-but-self, or a
specific CPU (including self).
This has not made its way to a PAPR release yet, but we have an hcall
number assigned.
H_SIGNAL_SYS_RESET = 0x380
Syntax:
hcall(uint64 H_SIGNAL_SYS_RESET, int64 target);
Generate a system reset NMI on the threads indicated by target.
Values for target:
-1 = target all online threads including the caller
-2 = target all online threads except for the caller
All other negative values: reserved
Positive values: The thread to be targeted, obtained from the value
of the "ibm,ppc-interrupt-server#s" property of the CPU in the OF
device tree.
Semantics:
- Invalid target: return H_Parameter.
- Otherwise: Generate a system reset NMI on target thread(s),
return H_Success.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The 'cpu_version' field in PowerPCCPU is badly named. It's named after the
'cpu-version' device tree property where it is advertised, but that meaning
may not be obvious in most places it appears.
Worse, it doesn't even really correspond to that device tree property. The
property contains either the processor's PVR, or, if the CPU is running in
a compatibility mode, a special "logical PVR" representing which mode.
Rename the cpu_version field, and a number of related variables to
compat_pvr to make this clearer.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Thomas Huth <thuth@redhat.com>
The pseries machine type is a bit unusual in that it runs a paravirtualized
guest. The guest expects to interact with a hypervisor, and qemu
emulates the functions of that hypervisor directly, rather than executing
hypervisor code within the emulated system.
To implement this in TCG, we need to intercept hypercall instructions and
direct them to the machine's hypercall handlers, rather than attempting to
perform a privilege change within TCG. This is controlled by a global
hook - cpu_ppc_hypercall.
This cleanup makes the handling a little cleaner and more extensible than
a single global variable. Instead, each CPU to have hypercalls intercepted
has a pointer set to a QOM object implementing a new virtual hypervisor
interface. A method in that interface is called by TCG when it sees a
hypercall instruction. It's possible we may want to add other methods in
future.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
spapr_h_cas_compose_response() includes a cpu_update parameter which
controls whether it includes updated information on the CPUs in the device
tree fragment returned from the ibm,client-architecture-support (CAS) call.
Providing the updated information is essential when CAS has negotiated
compatibility options which require different cpu information to be
presented to the guest. However, it should be safe to provide in other
cases (it will just override the existing data in the device tree with
identical data). This simplifies the code by removing the parameter and
always providing the cpu update information.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Currently the pseries machine has two paths for constructing CPUs. On
newer machine type versions, which support cpu hotplug, it constructs
cpu core objects, which in turn construct CPU threads. For older machine
versions it individually constructs the CPU threads.
This division is going to make some future changes to the cpu construction
harder, so this patch unifies them. Now cpu core objects are always
created. This requires some updates to allow core objects to be created
without a full complement of threads (since older versions allowed a
number of cpus not a multiple of the threads-per-core). Likewise it needs
some changes to the cpu core hot/cold plug path so as not to choke on the
old machine types without hotplug support.
For good measure, we move the cpu construction to its own subfunction,
spapr_init_cpus().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Move the generic cpu_synchronize_ functions to the common hw_accel.h header,
in order to prepare for the addition of a second hardware accelerator.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Message-Id: <f5c3cffe8d520011df1c2e5437bb814989b48332.1484045952.git.vpalatin@chromium.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We've currently got 18 architectures in QEMU, and thus 18 target-xxx
folders in the root folder of the QEMU source tree. More architectures
(e.g. RISC-V, AVR) are likely to be included soon, too, so the main
folder of the QEMU sources slowly gets quite overcrowded with the
target-xxx folders.
To disburden the main folder a little bit, let's move the target-xxx
folders into a dedicated target/ folder, so that target-xxx/ simply
becomes target/xxx/ instead.
Acked-by: Laurent Vivier <laurent@vivier.eu> [m68k part]
Acked-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de> [tricore part]
Acked-by: Michael Walle <michael@walle.cc> [lm32 part]
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com> [s390x part]
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com> [s390x part]
Acked-by: Eduardo Habkost <ehabkost@redhat.com> [i386 part]
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com> [sparc part]
Acked-by: Richard Henderson <rth@twiddle.net> [alpha part]
Acked-by: Max Filippov <jcmvbkbc@gmail.com> [xtensa part]
Reviewed-by: David Gibson <david@gibson.dropbear.id.au> [ppc part]
Acked-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> [crisµblaze part]
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn> [unicore32 part]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Currently we set the initial isolation/allocation state for DRCs
associated with coldplugged LMBs to ISOLATED/UNUSABLE,
respectively, under the assumption that the guest will move this
state to UNISOLATED/USABLE.
In fact, this is only the case for LMBs added via hotplug. For
coldplugged LMBs, the guest actually assumes the initial state to
be UNISOLATED/USABLE.
In practice, this only becomes an issue when we attempt to unplug
one of these LMBs, where the guest kernel will issue an
rtas-get-sensor-state call to check that the corresponding DRC is
in an USABLE state before it will release the LMB back to
QEMU. If the returned state is otherwise, the guest will assume no
further action is needed, which bypasses the QEMU-side cleanup that
occurs during the USABLE->UNUSABLE transition. This results in
LMBs and their corresponding pc-dimm devices to stick around
indefinitely.
This patch fixes the issue by manually setting DRCs associated with
cold-plugged LMBs to UNISOLATED/ALLOCATED, but leaving the hotplug
state untouched. As it turns out, this is analogous to the handling
for cold-plugged CPUs in spapr_core_plug().
Cc: qemu-ppc@nongnu.org
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Bharata B Rao <bharata@linux.vnet.ibm.com>
Cc: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
daa2369 "spapr_pci: Add a 64-bit MMIO window" subtly broke migration
from qemu-2.7 to the current version. It split the device's MMIO
window into two pieces for 32-bit and 64-bit MMIO.
The patch included backwards compatibility code to convert the old
property into the new format. However, the property value was also
transferred in the migration stream and compared with a (probably
unwise) VMSTATE_EQUAL. So, the "raw" value from 2.7 is compared to
the new style converted value from (pre-)2.8 giving a mismatch and
migration failure.
Along with the actual field that caused the breakage, there are
several other ill-advised VMSTATE_EQUAL()s. To fix forwards
migration, we read the values in the stream into scratch variables and
ignore them, instead of comparing for equality. To fix backwards
migration, we populate those scratch variables in pre_save() with
adjusted values to match the old behaviour.
To permit the eventual possibility of removing this cruft from the
stream, we only include these compatibility fields if a new
'pre-2.8-migration' property is set. We clear it on the pseries-2.8
machine type, which obviously can't be migrated backwards, but set it
on earlier machine type versions.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
This reverts commit 9b54ca0ba7.
The commit above corrected a migration breakage between qemu-2.7 and
qemu-2.8. However it did so by advancing the migration version for
the PCI host bridge, which obviously breaks migration backwards to
earlier qemu versions.
Although it's not totally essential, we'd like to maintain the
possibility for backwards migration, so revert the change in
preparation for a better fix.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Until very recently, the vmstate for ppc cpus included some poorly
thought out VMSTATE_EQUAL() components, that can easily break
migration compatibility, and did so between qemu-2.6 and later
versions. A hack was recently added which fixes this migration
breakage, but it leaves the unhelpful cruft of these fields in the
migration stream.
This patch adds a new cpu property allowing these fields to be removed
from the stream entirely. For the pseries-2.8 machine type - which
comes after the fix - and for all non-pseries machine types - which
aren't mature enough to care about cross-version migration - we remove
the fields from the stream.
For pseries-2.7 and earlier, The migration hack remains in place,
allowing backwards and forwards migration with the older machine
types.
This restricts the migration compatibility cruft to older machine
types, and at least opens the possibility of eventually deprecating
and removing it entirely.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
With the additional of the OV5_HP_EVT option vector, we now have
certain functionality (namely, memory unplug) that checks at run-time
for whether or not the guest negotiated the option via CAS. Because
we don't currently migrate these negotiated values, we are unable
to unplug memory from a guest after it's been migrated until after
the guest is rebooted and CAS-negotiation is repeated.
This patch fixes this by adding CAS-negotiated options to the
migration stream. We do this using a subsection, since the
negotiated value of OV5_HP_EVT is the only option currently needed
to maintain proper functionality for a running guest.
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
PC will use this field in other way, so move it outside the common
code so PC could set a different value, i.e. all CPUs
regardless of where they are coming from (-smp X | -device cpu...).
It's quick and dirty hack as it could be implemented in more generic
way in MashineClass. But do it in simple way since only PC is affected
so far.
Later we can generalize it when another affected target gets support
for -device cpu.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1479212236-183810-3-git-send-email-imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
