Interactive boot menu for scsi. This follows a similar procedure
as the interactive menu for eckd dasd. An example follows:
s390x Enumerated Boot Menu.
3 entries detected. Select from index 0 to 2.
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
[thuth: Added additional "break;" statement to avoid analyzer warnings]
Signed-off-by: Thomas Huth <thuth@redhat.com>
If no boot menu options are present, then flag the boot menu to
use the zipl options that were set in the zipl configuration file
(and stored on disk by zipl). These options are found at some
offset prior to the start of the zipl boot menu banner. The zipl
timeout value is limited to a 16-bit unsigned integer and stored
as seconds, so we take care to convert it to milliseconds in order
to conform to the rest of the boot menu functionality. This is
limited to CCW devices.
For reference, the zipl configuration file uses the following
fields in the menu section:
prompt=1 enable the boot menu
timeout=X set the timeout to X seconds
To explicitly disregard any boot menu options, then menu=off or
<bootmenu enable='no' ... /> must be specified.
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
It is possible while waiting for multiple types of external
interrupts that we might have pending irqs remaining between
irq consumption and irq-type disabling. Those interrupts
could potentially propagate to the guest after IPL completes
and cause unwanted behavior.
As it is today, the SCLP will only recognize write events that
are enabled by the control program's send and receive masks. To
limit the window for, and prevent further irqs from, ASCII
console events (specifically keystrokes), we should only enable
the control program's receive mask when we need it.
While we're at it, remove assignment of the (non control program)
send and receive masks, as those are actually set by the SCLP.
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Implements an sclp_read function to capture input from the
console and a wrapper function that handles parsing certain
characters and adding input to a buffer. The input is checked
for any erroneous values and is handled appropriately.
A prompt will persist until input is entered or the timeout
expires (if one was set). Example:
Please choose (default will boot in 10 seconds):
Correct input will boot the respective boot index. If the
user's input is empty, 0, or if the timeout expires, then
the default zipl entry will be chosen. If the input is
within the range of available boot entries, then the
selection will be booted. Any erroneous input will cancel
the timeout and re-prompt the user.
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
When the boot menu options are present and the guest's
disk has been configured by the zipl tool, then the user
will be presented with an interactive boot menu with
labeled entries. An example of what the menu might look
like:
zIPL v1.37.1-build-20170714 interactive boot menu.
0. default (linux-4.13.0)
1. linux-4.13.0
2. performance
3. kvm
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Read the stage2 boot loader data block-by-block. We scan the
current block for the string "zIPL" to detect the start of the
boot menu banner. We then load the adjacent blocks (previous
block and next block) to account for the possibility of menu
data spanning multiple blocks.
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reads boot menu flag and timeout values from the iplb and
sets the respective fields for the menu.
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Set boot menu options for an s390 guest and store them in
the iplb. These options are set via the QEMU command line
option:
-boot menu=on|off[,splash-time=X]
or via the libvirt domain xml:
<os>
<bootmenu enable='yes|no' timeout='X'/>
</os>
Where X represents some positive integer representing
milliseconds.
Any value set for loadparm will override all boot menu options.
If loadparm=PROMPT, then the menu will be enabled without a
timeout.
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The s390-ccw firmware needs some information in support of the
boot process which is not available on the native machine.
Examples are the netboot firmware load address and now the
boot menu parameters.
While storing that data in unused fields of the IPL parameter block
works, that approach could create problems if the parameter block
definition should change in the future. Because then a guest could
overwrite these fields using the set IPLB diagnose.
In fact the data in question is of more global nature and not really
tied to an IPL device, so separating it is rather logical.
This commit introduces a new structure to hold firmware relevant
IPL parameters set by QEMU. The data is stored at location 204 (dec)
and can contain up to 7 32-bit words. This area is available to
programming in the z/Architecture Principles of Operation and
can thus safely be used by the firmware until the IPL has completed.
Signed-off-by: Viktor Mihajlovski <mihajlov@linux.vnet.ibm.com>
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
[thuth: fixed "4 + 8 * n" comment]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Moved:
memcmp from bootmap.h to libc.h (renamed from _memcmp)
strlen from sclp.c to libc.h (renamed from _strlen)
Added C standard functions:
isdigit
Added non C-standard function:
uitoa
atoui
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
ECKD DASDs have different IPL structures for CDL and LDL
formats. The current Ipl1 and Ipl2 structs follow the CDL
format, so we prepend "EckdCdl" to them. Boot info for LDL
has been moved to a new struct: EckdLdlIpl1.
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Acked-by: Janosch Frank <frankja@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add new cylinder/head/sector struct. Use it to calculate
eckd block numbers instead of a BootMapPointer (which used
eckd chs anyway).
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Some ECKD bootmap code was using structs designed for SCSI.
Even though this works, it confuses readability. Add a new
BootMapTable struct to assist with readability in bootmap
entry code. Also:
- replace ScsiMbr in ECKD code with appropriate structs
- fix read_block messages to reflect BootMapTable
- fixup ipl_scsi to use BootMapTable (referred to as Program Table)
- defined value for maximum table entries
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This is skiboot 5.9 (commit e0ee24c2). It brings improved POWER9
support among many other things. Built from submodule.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The main changes are:
- able to handle more devices with specified bootindex;
- implements flatten device tree rendering, for both QEMU and guest kernel.
The full list is:
> boot: use a temporary bootdev-buf
> boot: do not concatenate bootdev
> libvirtio: Mark struct virtio_scsi_req_cmd as packed
> fdt: Implement "fdt-fetch" method for client interface
> rtas: Store RTAS address and entry in the device tree
> board-qemu: Fix slof-build-id length
> fdt: Pass the resulting device tree to QEMU
> fdt: Fix version and add a word for FDT header size
> tree: Rework set-chosen-cpu and store /chosen ihandle and phandle
> node: Add some documentation
> Revert various SLOF-to-QEMU private hypercalls
> Use input-device and output-device
> netboot: Create bootp-response when bootp is used
> libnet/ipv6: assign times_asked value directly
> usb-xhci: Reset ERSTSZ together with ERSTBA
> virtio-net: rework the driver to support multiple open
> board-qemu: add private hcall to inform host on "phandle" update
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The QEMU ELF loader does not zero the bss segment.
This resulted in several bugs, e.g. see
commit 5d739a4787 (s390-ccw.img: Fix sporadic errors with ccw boot image - initialize css)
commit 6a40fa2669d3 (s390-ccw.img: Initialize next_idx)
commit 8775d91a0f (pc-bios/s390-ccw: Fix problem with invalid virtio-scsi LUN when rebooting)
Let's fix this once and forever by letting the BIOS zero the bss itself.
Suggested-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <20171122142627.73170-3-borntraeger@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The owner of qemu.org has delegated authority to modify DNS records to
the QEMU Project. This has allowed us to use the domain name without
worries about IP address changes or technical issues disrupting service.
The issues described in commit 8593898109
("Use qemu-project.org domain name") have therefore been mitigated.
This patch switches back to consistently using qemu.org instead of
qemu-project.org in documentation, version.rc, and the Windows installer
script.
The git submodules and SeaBIOS still use qemu-project.org for the time
being. This will be fixed in the QEMU 2.12 release cycle.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20171121120435.28728-2-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Contains the following commit:
- pc-bios/s390-ccw: Fix problem with invalid virtio-scsi LUN when rebooting
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
When rebooting a guest that has a virtio-scsi disk, the s390-ccw
bios sometimes bails out with an error message like this:
! SCSI cannot report LUNs: STATUS=02 RSPN=70 KEY=05 CODE=25 QLFR=00, sure !
Enabling the scsi_req* tracing in QEMU shows that the ccw bios is
trying to execute the REPORT LUNS SCSI command with a LUN != 0, and
this causes the SCSI command to fail.
Looks like we neither clear the BSS of the s390-ccw bios during reboot,
nor do we explicitly set the default_scsi_device.lun value to 0, so
this variable can contain random values from the OS after the reboot.
By setting this variable explicitly to 0, the problem is fixed and
the reboots always succeed.
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1514352
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1510942228-22822-1-git-send-email-thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Update our pre-release seabios snapshot to the final release.
git shortlog
============
Gerd Hoffmann (1):
sercon: Disable ScreenAndDebug in case both serial console and serial debug are active
Kevin O'Connor (2):
timer: Avoid integer overflows in usec and nsec calculations
docs: Note v1.11.0 release
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
includes
7618c0aefe ("s390-ccw: print carriage return with new lines")
a8fbbf1db7 ("s390: set DHCP client architecure id for netboot")
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The sclp console in the s390 bios writes raw data,
leading console emulators (such as virsh console) to
treat a new line ('\n') as just a new line instead
of as a Unix line feed. Because of this, output
appears in a "stair case" pattern.
Let's print \r\n on every occurrence of a new line
in the string passed to write to amend this issue.
This is in sync with the guest Linux code in
drivers/s390/char/sclp_vt220.c which also does a line feed
conversion in the console part of the driver.
This fixes the s390-ccw and s390-netboot output like
$ virsh start test --console
Domain test started
Connected to domain test
Escape character is ^]
Network boot starting...
Using MAC address: 02:01:02:03:04:05
Requesting information via DHCP: 010
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Message-Id: <1509120893-28054-1-git-send-email-walling@linux.vnet.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
This is the seabios update for qemu 2.11. Well, almost, seabios is in
freeze for the upcoming 1.11 release. This updates seabios to current
git master snapshot, and it will be updated again to 1.11 final before
the 2.11 release.
With this two-step seabios gets some more wide testing before the actual
release and the update to 1.11 final (which will most likely happen
after qemu freeze) should have bugfix patches only.
git shortlog
============
Aleksandr Bezzubikov (3):
pci: refactor pci_find_capapibilty to get bdf as the first argument instead of the whole pci_device
pci: add QEMU-specific PCI capability structure
pci: enable RedHat PCI bridges to reserve additional resources on PCI init
Ben Warren (5):
QEMU DMA: Add DMA write capability
romfile-loader: Switch to using named structs
QEMU fw_cfg: Add command to write back address of file
QEMU fw_cfg: Add functions for accessing files by key
QEMU fw_cfg: Write fw_cfg back on S3 resume
Daniel Verkamp (5):
nvme: support NVMe 1.0 controllers
nvme: extend command timeout to 5 seconds
nvme: fix reversed loop condition in cmd_readwrite
nvme: fix extraction of status code bits
nvme: fix copy-paste mistake in comment
Filippo Sironi (1):
nvme: Use the Maximum Queue Entries Supported (MQES) to initialize I/O queues
Gerd Hoffmann (7):
usb: add hub portmap
usb-xhci: use hub portmap
std: add cp437 to unicode map
kbd: make enqueue_key public, add ascii_to_keycode
romfile: add support for constant files.
paravirt: serial console configuration.
add serial console support
Igor Mammedov (1):
drop "etc/boot-cpus" fw_cfg file and reuse legacy QEMU_CFG_NB_CPUS
Jason Wang (1):
virtio: IOMMU support
Julian Stecklina (2):
block: add NVMe boot support
nvme: fix out of memory behavior
Julius Werner (1):
coreboot: Adapt to upstream CBMEM console changes
Kevin O'Connor (26):
usb: Make usb_time_sigatt variable static
tpm: Add comment banners to tcg.c separating major parts of spec
tpm: Don't call tpm_set_failure() from tpm12_get_capability()
tpm: Move code around in tcgbios.c to keep like code together
acpi: Generalize find_fadt() and find_tcpa_by_rsdp() into find_acpi_table()
tpm: Don't call tpm_build_and_send_cmd() from tpm20_stirrandom()
tpm: Rework tpm_build_and_send_cmd() into tpm_simple_cmd()
ps2port: Disable keyboard/mouse prior to resetting ps2 controller
docs: Note release dates for 1.10.1 and 1.10.2
resume: Don't attempt to use generic reboot mechanisms on QEMU
boot: Increase description size in boot menu
src: Minor - remove tab characters that slipped into SeaBIOS C code
NVMe: Allow NVMe to be enabled on real hardware
smm: Backup and restore A20 on an SMI based mode switch
stacks: Make sure to initialize Call16Data
stacks: Don't update the A20 settings if they haven't changed
stacks: There is no need to disable NMI if it is already disabled
vga: Fix bug in stdvga_get_linesize()
docs: Fix typos in Memory_Model.md
tcgbios: Fix use of unitialized variable
boot: Rename drive_g to drive
disk: Don't require the 'struct drive_s' to be in the f-segment
block: Rename disk_op_s->drive_gf to drive_fl
virtio: Allocate drive_s storage in low memory
xhci: Build TRBs directly in xhci_trb_queue()
xhci: Verify the device is still present in xhci_cmd_submit()
Ladi Prosek (1):
ahci: Set upper 32-bit registers to zero
Patrick Rudolph (4):
SeaVGABios/cbvga: Advertise correct pixel format
SeaVGABIOS/vbe: Query driver for scanline pitch v2
SeaVGABios/cbvga: Use active mode to clear screen
SeaVGABios/cbvga: Advertise compatible VESA modes
Paul Menzel (1):
vgasrc: Increase debug level
Petr Berky (1):
config: Add function to check if fw_cfg exists
Ricardo Ribalda Delgado (1):
serialio: Support for mmap serial ports
Roman Kagan (11):
blockcmd: accept only disks and CD-ROMs
blockcmd: generic SCSI luns enumeration
virtio-scsi: enumerate luns with REPORT LUNS
esp-scsi: enumerate luns with REPORT LUNS
usb-uas: enumerate luns with REPORT LUNS
pvscsi: fix the comment about lun enumeration
mpt-scsi: try to enumerate luns with REPORT LUNS
lsi-scsi: reset in case of a serious problem
lsi-scsi: try to enumerate luns with REPORT LUNS
blockcmd: start REPORT_LUNS with the smallest buffer
Revert "lsi-scsi: reset in case of a serious problem"
Stefan Berger (1):
tpm: Log TPM 2 digest structure in little endian format
Youness Alaoui (1):
nvme: Enable NVMe support for non-qemu hardware
Zeh, Werner (1):
ahci: Disable Native Command Queueing
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch updates the sun4u model to being much closer to a real Ultra 5
by moving devices behind the 2 simba PCI bridges (A and B) as found on real
hardware.
The most noticeable change introduced by this patchset is that in-built devices
are no longer attached to the PCI root bus, but instead behind PCI bridge A.
Along with this the interrupt routing is updated accordingly to match the
official documentation.
Since the existing code currently bypasses the PCI bridge interrupt
swizzling, the interrupt mapping functions are reorganised so that
pci_pbm_map_irq() is used by the PCI bridges and pci_apb_map_irq() is
used by the PCI host bridge.
Behind the sabre PCI host bridge, the PCI IO space now needs to be
split into two separate halves at 0x8000000. Therefore we also setup a new
PCI IO space region of increased size on the PCI host bridge and enable
32-bit PCI IO accesses to allow IO accesses to reach devices behind PCI
bridge B correctly.
As part of this change we also combine the onboard sunhme NIC and the ebus
into a single multi-function device as done on a real Ultra 5. For other
NICs the existing behaviour is preserved, i.e. we initialise them and
place them into the next free slot on PCI bus B.
Finally we mark the physically unavailable slots (plus slot 0 in busA) as
reserved to ensure that users can't plug devices into non-existent slots
which will break interrupt routing.
Note: since this commit changes PCI topology and interrupt routing, an
updated openbios-sparc64 binary is included with this commit containing the
associated changes to maintain bisectability.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Artyom Tarasenko <atar4qemu@gmail.com>
Setting the client architecture DHCP option to 0x001f (s390 Basic) [1]
allows the DHCP server to return a s390-specific bootfile if wanted.
DHCP servers not configured for the option (or not yet recognizing the
option value) will continue to work as they have done before.
[1] https://www.iana.org/assignments/dhcpv6-parameters
Signed-off-by: Viktor Mihajlovski <mihajlov@linux.vnet.ibm.com>
Message-Id: <1505126027-1704-1-git-send-email-mihajlov@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The commit 198c0d1f9d s390x/css: check ccw address validity
exposes an alignment issue in ccw bios.
According to PoP the CCW must be doubleword aligned. Let's fix
this in the bios.
Cc: qemu-stable@nongnu.org
Signed-off-by: Farhan Ali <alifm@linux.vnet.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Eric Farman <farman@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <3ed8b810b6592daee6a775037ce21f850e40647d.1503667215.git.alifm@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
This reverts a change that replaced the "rm -f" command with the
undefined variable RM (expected to be set by make), and causes the
"make clean" command to fail for a s390 target:
make[1]: Entering directory '/usr/src/qemu/build/pc-bios/s390-ccw'
rm -f *.timestamp
*.o *.d *.img *.elf *~ *.a
/bin/sh: *.o: command not found
Makefile:39: recipe for target 'clean' failed
make[1]: *** [clean] Error 127
make[1]: Leaving directory '/usr/src/qemu/build/pc-bios/s390-ccw'
Makefile:489: recipe for target 'clean' failed
make: *** [clean] Error 1
Fixes: 3e4415a751 ("pc-bios/s390-ccw: Add core files for the network
bootloading program")
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Message-Id: <20170814204450.24118-2-farman@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The main changes are:
- fixes in PCI bridges code;
- LUN>255 are allowed not in virtio-scsi.
The full list is:
> pci-scan: Fix pci-bridge-set-mem-base and pci-bridge-set-mem-limit
> pci: Avoid 32-bit prefetchable memory area if possible
> Remove unused functions ishexdigit and $cat-comma
> pci: Translate PCI addresses to host addresses at the end of map-in
> Define 'open' and 'close' words of the /aliases nodes right from the start
> virtio-scsi: Allow LUNs bigger than 255
> paflof: Silence gcc's -Warray-bounds warning for stack pointers
> board_qemu: move code out of fdt-fix-node-phandle
> board_qemu: drop unused values early in fdt-fix-node-phandle
> pci: Improve the pci-var-out debug function
> libhvcall: drop unused KVMPPC_H_REPORT_MC_ERR and KVMPPC_H_NMI_MCE defines
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Quite a while has passed since we last updated U-Boot for e500. This patch
bumps it to the last released version 2017.07 to make sure users don't feel
like they're using out of date software.
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-id: 1499862868-102130-1-git-send-email-agraf@suse.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Rebase ipxe to latest git master.
Pick up four virtio-net fixes.
complete shortlog of ipxe changes
---------------------------------
Adamczyk, Konrad (1):
[thunderx] Use ThunderxConfigProtocol to obtain board configuration
Bartosz Szczepanek (1):
[thunderx] Fix hardware deinitialization
Christian Nilsson (1):
[intel] Add INTEL_NO_PHY_RST for I219-LM (2)
David Decotigny (2):
[build] Return const char * from uuid_ntoa()
[af_packet] Add new AF_PACKET driver for Linux
Jason Wang (1):
[virtio] Support VIRTIO_NET_F_IOMMU_PLATFORM
Jerone Young (1):
[intel] Add support for I219-V in 7th Gen Intel NUC
Konrad Adamczyk (1):
[thunderx] Don't disable NIC when exiting from iPXE
Ladi Prosek (3):
[virtio] Cap queue size to MAX_QUEUE_NUM
[virtio] Simplify virtqueue shutdown
[virtio] Remove queue size limit in legacy virtio
Martin Habets (1):
[sfc] Add driver for Solarflare SFC8XXX adapters
Michael Brown (159):
[interface] Provide intf_reinit() to reinitialise nullified interfaces
[iscsi] Avoid potential infinite loops during shutdown
[efi] Add basic EFI SAN booting capability
[undi] Allocate base memory before calling UNDI loader entry point
[romprefix] Avoid using PMM-allocated memory in UNDI loader entry point
[undi] Clean up driver and device name information
[prefix] Remove impossible progress message
[prefix] Include diagnostic information within progress messages
[undi] Try matching UNDI ROMs in BIOS enumeration order
[efi] Work around temporal anomaly encountered during ExitBootServices()
[ipv4] Accept unicast packets for the local network broadcast address
[build] Add %.vhd target for building VM bootable disk images
[virtio] Use separate RX and TX empty header buffers
[cloud] Add ability to retrieve Google Compute Engine metadata
[virtio] Use host-specified MTU when available
[netdevice] Allow MTU to be changed at runtime
[cloud] Show CPU vendor and model in example cloud boot scripts
[hyperv] Ignore unsolicited VMBus messages
[pic8259] Fix definitions for "read IRR" and "read ISR" commands
[efi] Fix building elf2efi.c when -fpic is enabled by default
[interface] Avoid unnecessary reference counting in intf_unplug()
[interface] Remove misleading comment
[interface] Unplug interface before calling intf_close() in intf_shutdown()
[netdevice] Limit MTU by hardware maximum frame length
[cpuid] Provide cpuid_supported() to test for supported functions
[time] Allow timer to be selected at runtime
[hyperv] Provide timer based on the 10MHz time reference count MSR
[int13] Avoid potential division by zero
[int13] Test correct return status from INT 13 calls
[settings] Add "unixtime" builtin setting to expose the current time
[time] Report attempts to use timers before initialisation
[interface] Provide the ability to shut down multiple interfaces
[http] Cleanly shut down potentially looped interfaces
[efi] Add missing SANBOOT_PROTO_HTTP to EFI default configuration
[block] Remove spurious comments
[block] Centralise SAN device abstraction
[block] Centralise "san-drive" setting
[int13] Refactor to use centralised SAN device abstraction
[efi] Refactor to use centralised SAN device abstraction
[block] Retry any SAN device operation
[iscsi] Use intfs_shutdown() when shutting down multiple interfaces
[scsi] Use intfs_shutdown() when shutting down multiple interfaces
[block] Use intfs_shutdown() when shutting down multiple interfaces
[scsi] Avoid duplicate calls to scsicmd_close()
[build] Provide common ARRAY_SIZE() definition
[efi] Update to current EDK2 headers
[efi] Add EFI_ACPI_TABLE_PROTOCOL header and GUID definition
[efi] Provide ACPI table description for SAN devices
[efi] Skip cable detection at initialisation where possible
[undi] Move PXE API caller back into UNDI driver
[dhcp] Allow vendor class to be changed in DHCP requests
[hermon] Avoid potential integer overflow when calculating memory mappings
[arbel] Avoid potential integer overflow when calculating memory mappings
[xfer] Ensure va_end() is called on failure path
[nfs] Fix double free bug on error path
[linda] Use correct length for memset()
[qib7322] Use correct length for memset()
[sis900] Remove extraneous memset() with incorrect length
[802.11] Remove redundant NULL pointer check after dereference
[crypto] Free correct pointer on the error path
[librm] Fail gracefully if asked to ioremap() a zero length
[usb] Use correct length for memcpy()
[mucurses] Attempt to fix test for empty string
[mucurses] Attempt to fix keypress processing logic
[mucurses] Attempt to fix resource leaks
[hyperv] Fix resource leaks on error path
[slam] Fix resource leak on error path
[slam] Avoid NULL pointer dereference in slam_pull_value()
[eoib] Avoid passing a NULL I/O buffer to netdev_tx_complete_err()
[http] Add missing check for memory allocation failure
[mucurses] Attempt to fix use of uninitialised buffer with strcat()
[xhci] Avoid accessing beyond end of endpoint context array
[build] Avoid confusing sparse in single-argument DBG() macros
[infiniband] Return status code from ib_create_cq() and ib_create_qp()
[infiniband] Return status code from ib_create_mi()
[block] Quell spurious Coverity size mismatch warning
[ath] Add missing break statements
[pixbuf] Avoid potential division by zero
[usb] Use correct length for memcpy()
[xen] Use standard calling pattern for asprintf()
[tcp] Use correct length for memset()
[video_subr] Use memmove() for overlapping memory copy
[arbel] Assert that mapping length is non-zero
[hermon] Assert that mapping length is non-zero
[tlan] Guard against failure to identify chip
[w89c840] Avoid potential array overrun
[sis190] Avoid NULL pointer dereference
[mucurses] Ensure SLK labels are always terminated
[coverity] Add Coverity user model
[malloc] Track maximum heap usage
[travis] Add minimal .travis.yml file
[travis] Build and run the unit test suite
[travis] Integrate with Coverity Scan
[rtl818x] Fix resource leak on error path
[pcnet32] Eliminate redundant register read
[iobuf] Increase minimum I/O buffer size to 128 bytes
[vxge] Fix use of stale I/O buffer on error path
[scsi] Avoid duplicate call to scsicmd_close() on TEST UNIT READY failure
[block] Add dummy SAN device
[block] Add basic multipath support
[int13] Improve geometry guessing for unaligned partitions
[int13con] Avoid overwriting random portions of SAN boot disks
[time] Add sleep_fixed() function to sleep without checking for Ctrl-C
[block] Allow SAN retry count to be reconfigured
[block] Add a small delay between attempts to reopen SAN targets
[block] Retry reopening indefinitely for multipath devices
[block] Gracefully close SAN device if registration fails
[linux] Use dummy SAN device
[block] Ignore redundant xfer_window_changed() messages
[block] Describe all SAN devices via ACPI tables
[iscsi] Do not install iBFT when no iSCSI targets exist
[http] Notify data transfer interface when underlying connection is ready
[mucurses] Fix erroneous __nonnull attribute
[build] Avoid implicit-fallthrough warnings on GCC 7
[linux] Fix building with kernel 4.11 headers
[scsi] Retry TEST UNIT READY command
[libc] Add stdbool.h standard header
[efi] Fix typo in efi_acpi_table_protocol_guid
[efi] Add efi_sprintf() and efi_vsprintf()
[block] Allow use of a non-default EFI SAN boot filename
[intel] Show original CTRL and STATUS values in debugging output
[intel] Do not enable ASDE on i350 backplane NIC
[block] Provide sandev_read() and sandev_write() as global symbols
[block] Provide abstraction to allow system to be quiesced
[hyperv] Do not fail if guest OS ID MSR is already set
[hyperv] Remove redundant return status code from mapping functions
[hyperv] Cope with Windows Server 2016 enlightenments
[efi] Standardise PCI debug messages
[iscsi] Always send FirstBurstLength parameter
[iscsi] Fix iBFT when no explicit initiator name setting exists
[xen] Provide 18 4kB receive buffers to work around xen-netback bug
[efi] Prevent EFI code from being linked in to non-EFI builds
[tls] Keep cipherstream window open until TLS negotiation is complete
[settings] Extend numerical setting tags to 64 bits
[acpi] Make acpi_find_rsdt() a per-platform method
[efi] Provide access to ACPI tables
[acpi] Expose ACPI tables via settings mechanism
[syslog] Handle backspace characters
[hdprefix] Avoid attempts to read beyond the end of the disk
[usb] Allow for USB network devices with no interrupt endpoint
[build] Use -no-pie on newer versions of gcc
[ecm] Display invalid MAC address strings in debug messages
[cpuid] Allow input %ecx value to be specified
[crypto] Expose RSA_CTX_SIZE constant
[crypto] Expose asn1_grow()
[crypto] Provide asn1_built() to construct a cursor from a builder
[crypto] Expose pem_asn1() for use with non-image data
[exanic] Add driver for Exablaze ExaNIC cards
[usb] Use non-zero language ID to retrieve strings
[mucurses] Avoid potential division by zero
[tls] Support RFC5746 secure renegotiation
[smscusb] Abstract out common SMSC USB device functionality
[smsc95xx] Use common SMSC USB device functionality
[smsc75xx] Use common SMSC USB device functionality
[smscusb] Add ability to read MAC address from OTP
[smscusb] Move non-inline register access functions to smscusb.c
[smscusb] Allow for alternative PHY register layouts
[smsc75xx] Expose functionality shared with LAN78xx devices
[lan78xx] Add driver for Microchip LAN78xx USB Ethernet NICs
Mika Tiainen (1):
[intel] Add INTEL_NO_PHY_RST for I219-V
Mike McCormack (1):
[sky2] Use 32-bit read to read Y2_VAUX_AVAIL
Raed Salem (2):
[golan] Update Connect-IB, ConnectX-4 and ConnectX-4 Lx (Infiniband) support
[golan] Bug fixes and improved paging allocation method
Vishvananda Ishaya (1):
[intel] Reset all virtual function settings
Vishvananda Ishaya Abrams (1):
[iscsi] Don't close when receiving NOP-In
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
- add a network boot rom for s390 (Thomas Huth)
- migration of storage attributes like the CMMA used/unused state
- PCI related enhancements - full support for aen, ais and zpci
- migration support for css with vmstates (Halil Pasic)
- cpu model enhancements for cpu features
- guarded storage support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=2bOV
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/borntraeger/tags/s390x-20170714' into staging
s390x/kvm/migration/cpumodel: fixes, enhancements and cleanups
- add a network boot rom for s390 (Thomas Huth)
- migration of storage attributes like the CMMA used/unused state
- PCI related enhancements - full support for aen, ais and zpci
- migration support for css with vmstates (Halil Pasic)
- cpu model enhancements for cpu features
- guarded storage support
# gpg: Signature made Fri 14 Jul 2017 11:33:04 BST
# gpg: using RSA key 0x117BBC80B5A61C7C
# gpg: Good signature from "Christian Borntraeger (IBM) <borntraeger@de.ibm.com>"
# Primary key fingerprint: F922 9381 A334 08F9 DBAB FBCA 117B BC80 B5A6 1C7C
* remotes/borntraeger/tags/s390x-20170714: (40 commits)
s390x/gdb: add gs registers
s390x/arch_dump: also dump guarded storage control block
s390x/kvm: enable guarded storage
s390x/kvm: Enable KSS facility for nested virtualization
s390x/cpumodel: add esop/esop2 to z12 model
s390x/cpumodel: we are always in zarchitecture mode
s390x/cpumodel: wire up new hardware features
s390x/flic: migrate ais states
s390x/cpumodel: add zpci, aen and ais facilities
s390x: initialize cpu firstly
pc-bios/s390: rebuild s390-ccw.img
pc-bios/s390: add s390-netboot.img
pc-bios/s390-ccw: Link libnet into the netboot image and do the TFTP load
pc-bios/s390-ccw: Add virtio-net driver code
pc-bios/s390-ccw: Add core files for the network bootloading program
roms/SLOF: Update submodule to latest status
pc-bios/s390-ccw: Add code for virtio feature negotiation
pc-bios/s390-ccw: Remove unused structs from virtio.h
pc-bios/s390-ccw: Move byteswap functions to a separate header
pc-bios/s390-ccw: Add a write() function for stdio
...
Conflicts:
target/s390x/kvm.c
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
rebuild after the following commits
4b996d0 pc-bios/s390-ccw: Link libnet into the netboot image and do the TFTP load
e6879a6 pc-bios/s390-ccw: Add virtio-net driver code
766500f pc-bios/s390-ccw: Add core files for the network bootloading program
f807e55 pc-bios/s390-ccw: Add code for virtio feature negotiation
b4e3b4f pc-bios/s390-ccw: Remove unused structs from virtio.h
dd3dc5e pc-bios/s390-ccw: Move byteswap functions to a separate header
a20b4fe pc-bios/s390-ccw: Add a write() function for stdio
262e07c pc-bios/s390-ccw: Move virtio-block related functions into a separate file
7438d32 pc-bios/s390-ccw: Move ebc2asc to sclp.c
8760bad pc-bios/s390-ccw: Move libc functions to separate header
c68f450 pc-bios/s390-ccw: use STRIP variable in Makefile
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
It's already possible to do a network boot of an s390x guest with an
external netboot image based on a Linux installation, but it would
be much more convenient if the s390-ccw firmware supported network
booting right out of the box, without the need to assemble such an
external image first.
This is an s390-netboot.img that can be used for network booting.
You can download a combined kernel + initrd image via TFTP
by starting QEMU for example with:
qemu-system-s390x ... -device virtio-net,netdev=n1,bootindex=1 \
-netdev user,id=n1,tftp=/path/to/tftp,bootfile=kernel.img
Note that this version does not support downloading via config
files (i.e. pxelinux config files or .INS config files) yet. This
will be added later.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Most of the code has been taken from SLOF's netload.c file. Now we
can finally load an image via TFTP and execute the downloaded kernel.
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1499863793-18627-12-git-send-email-thuth@redhat.com>
Tested-by: Viktor Mihajlovski <mihajlov@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The driver provides the recv() and send() functions which will
be required by SLOF's libnet code for receiving and sending
packets.
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1499863793-18627-11-git-send-email-thuth@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
This is just a preparation for the next steps: Add a makefile and a
stripped down copy of pc-bios/s390-ccw/main.c as a basis for the network
bootloader program, linked against the libc from SLOF already (which we
will need for SLOF's libnet). The networking code is not included yet.
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1499863793-18627-10-git-send-email-thuth@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The upcoming virtio-net driver needs to negotiate some features,
so we need the possibility to do this in the core virtio code.
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1499863793-18627-8-git-send-email-thuth@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Looks like they have never been used, so let's simply remove them.
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1499863793-18627-7-git-send-email-thuth@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
We'll need them in code that is not related to bootmap.h, so
they should reside in an independent header.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1499863793-18627-6-git-send-email-thuth@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The stdio functions from the SLOF libc need a write() function for
printing text to stdout/stderr. Let's implement this function by
refactoring the code from sclp_print().
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1499863793-18627-5-git-send-email-thuth@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The netboot code is going to link against the code from virtio.c, too, so
we've got to move the virtio-block and -scsi related code out of the way.
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1499863793-18627-4-git-send-email-thuth@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
We will later need this array in a file that we will link to the
netboot code, too. Since there is some ebcdic conversion done
in sclp_get_loadparm_ascii(), the sclp.c file seems to be a good
candidate.
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1499863793-18627-3-git-send-email-thuth@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The upcoming netboot code will use the libc from SLOF. To be able
to still use s390-ccw.h there, the libc related functions in this
header have to be moved to a different location.
And while we're at it, remove the duplicate memcpy() function from
sclp.c.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1499863793-18627-2-git-send-email-thuth@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The ROM uses the cmovne instruction, which is new in Pentium Pro and does not
work when running QEMU with "-cpu 486". Avoid producing that instruction.
Suggested-by: Richard W.M. Jones <rjones@redhat.com>
Suggested-by: Thomas Huth <thuth@redhat.com>
Reported-by: Rob Landley <rob@landley.net>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The docker-run-test-build@debian-s390x-cross target fails with:
strip --strip-unneeded s390-ccw.elf -o s390-ccw.img
strip: Unable to recognise the format of the input file `s390-ccw.elf'
The configure script defines a STRIP makefile variable whose default
value is ${cross_prefix}strip. Let's use it.
We default to using the non-prefixed strip command in case --enable-debug
or --disable-strip was passed to configure during a regular build.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <149623617700.4947.12490877660892961664.stgit@bahia.lan>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Contains the following commits:
- pc-bios/s390-ccw: Remove duplicate blk_factor adjustment
- pc-bios/s390-ccw: Move SCSI block factor to outer read
- pc-bios/s390-ccw: Break up virtio-scsi read into multiples
- pc-bios/s390-ccw: Refactor scsi_inquiry function
- pc-bios/s390-ccw: Get list of supported EVPD pages
- pc-bios/s390-ccw: Get Block Limits VPD device data
- pc-bios/s390-ccw: Build a reasonable max_sectors limit
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Message-Id: <20170510155359.32727-9-farman@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Now that we've read all the possible limits that have been defined for
a virtio-scsi controller and the disk we're booting from, it's possible
that we are STILL going to exceed the limits of the host device.
For example, a "-device scsi-generic" device does not support the
Block Limits VPD page.
So, let's fallback to something that seems to work for most boot
configurations if larger values were specified (including if nothing
was explicitly specified, and we took default values).
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Message-Id: <20170510155359.32727-8-farman@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The "Block Limits" Inquiry VPD page is optional for any SCSI device,
but if it's supported it provides a hint of the maximum I/O transfer
length for this particular device. If this page is supported by the
disk, let's issue that Inquiry and use the minimum of it and the
SCSI controller limit. That will cover this scenario:
qemu-system-s390x ...
-device virtio-scsi-ccw,id=scsi0,max_sectors=32768 ...
-drive file=/dev/sda,if=none,id=drive0,format=raw ...
-device scsi-hd,bus=scsi0.0,channel=0,scsi-id=0,
drive=drive0,id=disk0,max_io_size=1048576
controller: 32768 sectors x 512 bytes/sector = 16777216 bytes
disk: 1048576 bytes
Now that we have a limit for a virtio-scsi disk, compare that with the
limit for the virtio-scsi controller when we actually build the I/O.
The minimum of these two limits should be the one we use.
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Message-Id: <20170510155359.32727-7-farman@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The "Supported Pages" Inquiry EVPD page is mandatory for all SCSI devices,
and is used as a gateway for what VPD pages the device actually supports.
Let's issue this Inquiry, and dump that list with the debug facility.
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Message-Id: <20170510155359.32727-6-farman@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
If we want to issue any of the SCSI Inquiry EVPD pages,
which we do, we could use this function to issue both types
of commands with a little bit of refactoring.
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Message-Id: <20170510155359.32727-5-farman@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
A virtio-scsi request that goes through the host sd driver and exceeds
the maximum transfer size is automatically broken up for us. But the
equivalent request going to the sg driver presumes that any length
requirements have already been honored.
Let's use the max_sectors field on the virtio-scsi controller device,
and break up all requests (both sd and sg) to avoid this problem.
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Message-Id: <20170510155359.32727-4-farman@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Simple refactoring so that the blk_factor adjustment is
moved into virtio_scsi_read_many routine, in preparation
for another change.
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Message-Id: <20170510155359.32727-3-farman@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
When using virtio-scsi, we multiply the READ(10) data_size by
a block factor twice when building the I/O. This is fine,
since it's only 1 for SCSI disks, but let's clean it up.
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <20170510155359.32727-2-farman@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The QemuMacDrivers project provides virtualisation drivers for PPC MacOS
guests.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
but it'll come in the next pull request.
* use GDB XML register description for x86
* use _Static_assert in QEMU_BUILD_BUG_ON
* add "R:" to MAINTAINERS and get_maintainers
* checkpatch improvements
* dump threading fixes
* first part of vhost-user-scsi support
* QemuMutex tracing
* vmw_pvscsi and megasas fixes
* sgabios module update
* use Rev3 (ACPI 2.0) FADT
* deprecate -hdachs
* improve -accel documentation
* hax fix
* qemu-char GSource bugfix
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJZDE+gAAoJEL/70l94x66DIpYH/1IOz3u8ObD8D4Lor07LkCCZ
vWFnTBMgGi9gTL5JQDnukRR3cmNp9EVOtAP5Yf+v+/Xqyq/FNGnoVWxCxEby7LtN
zrIXbsKMCaEcGzRNJFcbKV+KZnzkJrz92J0NHy29ruCK1AsslOXAWf4Qb1MV+fQl
6w2Upsh35usvWCNpFm2o8arzMEmNuE2xJDPKUB11GMrZT6TExq4Zqa8Zj1Ihc0sX
XcDr+eeBmb65Vv3jQLntOhSWAy0Xxf/fDXYTQx+JLHFgvpSOIWMiS+fqIVXtT0bH
0E4hQrBr0qjes8n8+9WGGQW2k8Ak0QlDvrZnQ97hTeV1k6SxW+2ATO2mLeJp9TM=
=5hf2
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'bonzini/tags/for-upstream' into staging
A large set of small patches. I have not included yet vhost-user-scsi,
but it'll come in the next pull request.
* use GDB XML register description for x86
* use _Static_assert in QEMU_BUILD_BUG_ON
* add "R:" to MAINTAINERS and get_maintainers
* checkpatch improvements
* dump threading fixes
* first part of vhost-user-scsi support
* QemuMutex tracing
* vmw_pvscsi and megasas fixes
* sgabios module update
* use Rev3 (ACPI 2.0) FADT
* deprecate -hdachs
* improve -accel documentation
* hax fix
* qemu-char GSource bugfix
# gpg: Signature made Fri 05 May 2017 06:10:40 AM EDT
# gpg: using RSA key 0xBFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* bonzini/tags/for-upstream: (21 commits)
vhost-scsi: create a vhost-scsi-common abstraction
libvhost-user: replace vasprintf() to fix build
get_maintainer: add subsystem to reviewer output
get_maintainer: --r (list reviewer) is on by default
get_maintainer: it's '--pattern-depth', not '-pattern-depth'
get_maintainer: Teach get_maintainer.pl about the new "R:" tag
MAINTAINERS: Add "R:" tag for self-appointed reviewers
Fix the -accel parameter and the documentation for 'hax'
dump: Acquire BQL around vm_start() in dump thread
hax: Fix memory mapping de-duplication logic
checkpatch: Disallow glib asserts in main code
trace: add qemu mutex lock and unlock trace events
vmw_pvscsi: check message ring page count at initialisation
sgabios: update for "fix wrong video attrs for int 10h,ah==13h"
scsi: avoid an off-by-one error in megasas_mmio_write
vl: deprecate the "-hdachs" option
use _Static_assert in QEMU_BUILD_BUG_ON
target/i386: Add GDB XML register description support
char: Fix removing wrong GSource that be found by fd_in_tag
hw/i386: Build-time assertion on pc/q35 reset register being identical.
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Contains the following commits:
- pc-bios/s390-ccw: Make ebcdic/ascii conversion public
- pc-bios/s390-ccw: get LOADPARM stored in SCP Read Info
- pc-bios/s390-ccw: provide a function to interpret LOADPARM value
- pc-bios/s390-ccw: provide entry selection on LOADPARM for SCSI disk
- pc-bios/s390-ccw: add boot entry selection for ECKD DASD
- pc-bios/s390-ccw: add boot entry selection to El Torito routine
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
If there is no LOADPARM given or '0' specified, then IPL the first
matched entry. Otherwise IPL the matching entry of that number.
Signed-off-by: Eugene (jno) Dvurechenski <jno@linux.vnet.ibm.com>
Signed-off-by: Farhan Ali <alifm@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
1. change a bit definition of ScsiMbr to allow an array of pointers
2. add loadparm fetch to boot script processing
3. apply loadparm index to boot entry selection, if any
Initial patch from Eugene (jno) Dvurechenski.
Signed-off-by: Eugene (jno) Dvurechenski <jno@linux.vnet.ibm.com>
Signed-off-by: Farhan Ali <alifm@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Fix SCSI bootmap interpreter to make use of any specified entry of the
Program Table using the leftmost numeric value from the LOADPARM, if specified.
Initial patch from Eugene (jno) Dvurechenski.
Signed-off-by: Eugene (jno) Dvurechenski <jno@linux.vnet.ibm.com>
Signed-off-by: Farhan Ali <alifm@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The LOADPARM value is fetched from SCP Read Info, but it's applied
only at the phase of bootmap interpretation. So let's read the LOARPARM
value and store it. Also provide a parsing function to detect numbers in
the LOADPARM which can be used during bootmap interpretation.
Remove a stray whitespace.
Initial patch from Eugene (jno) Dvurechenski.
Signed-off-by: Eugene (jno) Dvurechenski <jno@linux.vnet.ibm.com>
Signed-off-by: Farhan Ali <alifm@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Obtain the loadparm value stored in SCP Read Info by performing
a SCLP Read Info request.
Rename sclp-ascii.c to sclp.c to reflect the changed scope of
the file.
Signed-off-by: Farhan Ali <alifm@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Make the ebcdic_to_ascii function public to the rest of the
"bios" code, as the volume label is no more the single thing
to be converted.
Signed-off-by: Eugene (jno) Dvurechenski <jno@linux.vnet.ibm.com>
Signed-off-by: Farhan Ali <alifm@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Various fixes in this update, the full list is:
> qemu-bootlist: Take the "-boot strict=off" setting properly into account
> virtio-scsi: initialize vring avail queue buffers
> virtio: Remove global variables in block and 9p driver
> Remove superfluous checkpoints in tree.fs
> Provide "write" function in the disk-label package
> virtio: Implement block write support
> scsi: Add SCSI block write support
> deblocker: Add a 'write' function
> virtio-scsi: Fix descriptor order for SCSI WRITE commands
> board-qemu: Add a possibility to use hvterm input instead of USB keyboard
> Do not try to use virtio-gpu in VGA mode
> virtio: Fix stack comment of virtio-blk-read
> envvar: Do not read default values for /options from the NVRAM anymore
> envvar: Set properties in /options during "(set-defaults)"
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We want to use the ccw bios to start final network boot. To do
this we use ccw bios to detect if the boot device is a virtio
network device and retrieve the start address of the
network boot image.
Signed-off-by: Farhan Ali <alifm@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
git shortlog rel-1.10.1..rel-1.10.2
===================================
Ben Warren (5):
QEMU DMA: Add DMA write capability
romfile-loader: Switch to using named structs
QEMU fw_cfg: Add command to write back address of file
QEMU fw_cfg: Add functions for accessing files by key
QEMU fw_cfg: Write fw_cfg back on S3 resume
Kevin O'Connor (1):
ps2port: Disable keyboard/mouse prior to resetting ps2 controller
Ladi Prosek (1):
ahci: Set upper 32-bit registers to zero
Paul Menzel (1):
vgasrc: Increase debug level
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
git shortlog 04186319..b991c67c
===============================
Laszlo Ersek (3):
[efi] Install the HII config access protocol on a child of the SNP handle
[librm] Conditionalize the workaround for the Tivoli VMM's SSE garbling
[build] Disable TIVOLI_VMM_WORKAROUND in the qemu configuration
Lukas Grossar (1):
[intel] Add PCI device ID for I219-V/LM
Michael Brown (57):
[efi] Fix uninitialised data in HII IFR structures
[bios] Do not enable interrupts when printing to the console
[pxe] Disable interrupts on the PIC before starting NBP
[dhcp] Allow for variable encapsulation of architecture-specific options
[dhcpv6] Include RFC5970 client architecture options in DHCPv6 requests
[dhcpv6] Include vendor class identifier option in DHCPv6 requests
[dhcp] Automatically generate vendor class identifier string
[xfer] Send intf_close() if redirection fails
[downloader] Treat redirection failures as fatal
[iscsi] Treat redirection failures as fatal
[debug] Allow per-object runtime enabling/disabling of debug messages
[debug] Allow debug messages to be initially disabled at runtime
[libc] Allow assertions to be globally enabled or disabled
[profile] Allow profiling to be globally enabled or disabled
[rng] Check for functioning RTC interrupt
[acpi] Add support for ACPI power off
[acpi] Allow time for ACPI power off to take effect
[ipv4] Send gratuitous ARPs whenever a new IPv4 address is applied
[intel] Strip spurious VLAN tags received by virtual function NICs
[intel] Remove duplicate intelvf_mbox_queues() function
[ipv6] Perform SLAAC only during autoconfiguration
[settings] Create space for IPv6 in settings display order
[ipv6] Rename ipv6_scope to dhcpv6_scope
[settings] Correctly mortalise autovivified child settings blocks
[ipv6] Allow settings to comprise arbitrary subsets of NDP options
[ipv6] Expose IPv6 settings acquired through NDP
[dhcpv6] Expose IPv6 address setting acquired through DHCPv6
[ipv6] Expose IPv6 link-local address settings
[settings] Allow settings blocks to specify a sibling ordering
[ipv6] Match user expectations for IPv6 settings priorities
[ipv6] Create routing table based on IPv6 settings
[ipv6] Rename ipv6_scope to ipv6_settings_scope
[test] Update IPv6 tests to use okx()
[ipv6] Allow for multiple routers
[hyperv] Use instance UUID in device name
[crypto] Remove obsolete extern declaration for asn1_invalidate_cursor()
[crypto] Allow for parsing of partial ASN.1 cursors
[image] Add image_asn1() to extract ASN.1 objects from image
[crypto] Add DER image format
[crypto] Add PEM image format
[image] Use image_asn1() to extract data from CMS signature images
[build] Remove obsolete explicit object requirements
[crypto] Enable both DER and PEM formats by default
[build] Remove more obsolete explicit object requirements
[pixbuf] Enable PNG format by default
[crypto] Add image_x509() to extract X.509 certificates from image
[crypto] Generalise X.509 "valid" field to a "flags" field
[list] Add list_next_entry() and list_prev_entry()
[crypto] Expose certstore_del() to explicitly remove stored certificates
[crypto] Allow certificates to be marked as having been added explicitly
[crypto] Add certstat() to display basic certificate information
[cmdline] Add certificate management commands
[crypto] Mark permanent certificates as permanent
[efi] Mark AppleNetBoot.h as a native iPXE header
[efi] Update to current EDK2 headers
[efi] Add EFI_BLOCK_IO2_PROTOCOL header and GUID definition
[bzimage] Fix page alignment of initrd images
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This pull request supersedes and extends the one from 2016-10-26
(which had a build bug).
Highlights:
* SLOF (pseries guest firmware) update
* Enable a number of extra testcases on ppc / pseries
* Added the 'powernv' machine type
- Almost enough to be minimally usable
- But still missing necessary interrupt controller updates
* Cleanup and consolidation of NVRAM handling on several platforms
with related firmware
* Substantial cleanup to device tree construction
* Some more POWER9 instruction emulation
* Cleanup to handling of pseries option vectors and CAS reboot
handling (host/guest feature negotiation mechanism)
* Significant cleanups to handling of PCI devices in test cases
* New hotplug event infrastructure
* Memory hot unplug support for pseries
* Several bug fixes
The NVRAM cleanup affects some Sun sparc platforms as well as ppc
ones, but have been tested by the sparc maintainer (Mark Cave-Ayland).
The test additions also include substantial general changes to the
test framework that aren't strictly ppc related. They don't seem to
break tests on other platforms, they're for the benefit of enabling
tests on ppc and there isn't a specific maintainer for them, so
they're included in this tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJYEqvPAAoJEGw4ysog2bOSQiwP/jOr5bxwZmGDrOwAIzqhagib
lo0+W1E6OCttbBhAp1inWZP6RnexAZ7orb+Q7DHQFbtYukUbPYwB/VzmWhaws6XV
jxK/lVB3A+XlRIEKUUc8bWWGRN+QBMnQIcUhNlKuC4AVKMC1aZY9ZLT6LvilV6X7
QtxAlBPmI2od2kyDHt/ibG9FkROFMi9ybbQG+D7Pu32NlTPgF06R6NPKtpkjEpUU
dRYAUB+VTB4eofjzyVqsL+QB7uX5g0V9aPmYWBaXqjTG61ivHMJJ7zHta+GdckJM
fk3S68ftPmf4EE+uL1Ff2fy+2Sxjh4QeNwxl1rppzrgvW8VkNOX6969idxSERUb8
I2/RVM7F1mJ7+4fNIjenAru8qu3O981lU9+t7R5mmTcEsSk28FOkOv6Io+6JnGA2
32qgOXwihsUDaH2pDagZ+ySaOqjWMD9WGQTfQgFMthGkcs6heG7ByvFrcpcacl5a
kbMl7cj+zkgusLuQHx0dp669R7Ch7bxSigQC11iMCpAmFhXl8qJ37ACPJn8NlzOq
NJdZwXOp9plYZ70a2CgKVXB6j+jhxOeJHg2v08jfF0rUILovBwH0WOrl1m0fb2gB
1u+ua2FED+5rtwpGJ7pL/oE20H11QDfHNDvqEpagvHAHSSu5nqGxd/falYRYE59C
wdMXPqJYQqkSYuA6XkgO
=3Z5V
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.8-20161028' into staging
ppc patch queue 2016-10-28
This pull request supersedes and extends the one from 2016-10-26
(which had a build bug).
Highlights:
* SLOF (pseries guest firmware) update
* Enable a number of extra testcases on ppc / pseries
* Added the 'powernv' machine type
- Almost enough to be minimally usable
- But still missing necessary interrupt controller updates
* Cleanup and consolidation of NVRAM handling on several platforms
with related firmware
* Substantial cleanup to device tree construction
* Some more POWER9 instruction emulation
* Cleanup to handling of pseries option vectors and CAS reboot
handling (host/guest feature negotiation mechanism)
* Significant cleanups to handling of PCI devices in test cases
* New hotplug event infrastructure
* Memory hot unplug support for pseries
* Several bug fixes
The NVRAM cleanup affects some Sun sparc platforms as well as ppc
ones, but have been tested by the sparc maintainer (Mark Cave-Ayland).
The test additions also include substantial general changes to the
test framework that aren't strictly ppc related. They don't seem to
break tests on other platforms, they're for the benefit of enabling
tests on ppc and there isn't a specific maintainer for them, so
they're included in this tree.
# gpg: Signature made Fri 28 Oct 2016 02:37:19 BST
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.8-20161028: (73 commits)
ppc: allow certain HV interrupts to be delivered to guests
spapr: Memory hot-unplug support
spapr: use count+index for memory hotplug
spapr: Add DRC count indexed hotplug identifier type
spapr: add hotplug interrupt machine options
spapr_events: add support for dedicated hotplug event source
spapr: update spapr hotplug documentation
target-ppc: Add xvcmpnesp, xvcmpnedp instructions
target-ppc: add xscmp[eq,gt,ge,ne]dp instructions
tests: Add pseries machine to the prom-env-test, too
spapr_nvram: Pre-initialize the NVRAM to support the -prom-env parameter
libqos: Change PCI accessors to take opaque BAR handle
tests: Don't assume structure of PCI IO base in ahci-test
tests: Use qpci_mem{read,write} in ivshmem-test
libqos: Add 64-bit PCI IO accessors
tests: Clean up IO handling in ide-test
libqos: Implement mmio accessors in terms of mem{read,write}
libqos: Add streaming accessors for PCI MMIO
tests: Adjust tco-test to use qpci_legacy_iomap()
libqos: Better handling of PCI legacy IO
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is the initial image of skiboot 5.3.7 (commit 762d0082) for
the PowerPC PowerNV (Non-Virtualized) platform. Built from
submodule.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The main changes are:
* virtio-serial
* booting speed imrovement
* better PCI bridge support
The complete changelog is:
> virtio-serial: Fix compile error
> scsi: Remove debug functions from scsi-loader.fs
> scsi: Remove unused read-6 command
> obp-tftp: Remove the ciregs-buffer
> libnet: Simplify the net-load arguments passing
> libnet: Simplify the Forth-to-C wrapper of ping()
> Do not link libnet to net-snk anymore, and remove net-snk from board-qemu
> Add a Forth-to-C wrapper for the ping command, too
> Link libnet code to Paflof and add a wrapper for netboot()
> Remember execution tokens of "write" and "read" for socket operations
> Add virtio-serial device support
> Generalize output banner write routine
> Improve indentation in OF.fs
> scsi: implement READ (16) command
> rtas: Improve rtas-do-config-@ and rtas-do-config-! a little bit
> libnet: Make netapps.h includable from .code files
> libnet: Remove unused prototypes from netapps.h
> libnet: Fix the printout of the ping command
> libnet: Make sure to close sockets when we're done
> scsi: implement read-capacity-16
> pci: Fix secondary and subordinate PCI bus enumeration with board-qemu
> pci-phb: Fix stack underflow in phb-pci-walk-bridge
> paflof: Add a read() function to read keyboard input
> paflof: Add socket(), send() and recv() functions to paflof
> paflof: Provide get_timer() and set_timer() helper functions
> paflof: Add a write_mm_log helper function
> paflof: Copy sbrk code from net-snk
> paflof: Use CFLAGS from make.rules instead of completely redefining them
> Do not include the FCode evaluator by default anymore
> Source code beautification of board-qemu/slof/pci-interrupts.fs
> Allow PCI devices in PCI bridge slots greater than 4
> Fix bad interrupt pin numbering in interrupt-map property of PCI bridges
> Improve SLOF_alloc_mem_aligned()
> instance: Fix set-my-args for empty arguments
> Fix remaining compiler warnings in sloffs.c
> Remove misleading padding fields from ROM header definition
> Improve indentation in calculatecrc.h
> Do not include calculatecrc.h from assembler files
> Remove unused defines in calculatecrc.h
> libnet: Re-initialize global variables at the beginning of tftp()
> Remove dependency on cpu/@0 for booting
> usb: Set XHCI slot speed according to port status
> usb: Build correct route string for USB3 devices behind a hub
> usb: Initialize USB3 devices on a hub and keep track of hub topology
> usb: Increase amount of maximum slot IDs and add a sanity check
> usb: Move XHCI port state arrays from header to .c file
> tools: add copy functionality
> tools: added support to sloffs to read from /dev/slof_flash
> tools: added file append functionality
> tools: use crc checking code from romfs/tools
> tools: added initial version of sloffs
> romfs: factored out crc code, to make it usable from other locations
> tools: remove unused parts from the Makefile
> usb-hid: Fix non-working comma key
> fat-files: Fix access to FAT32 dir/files when cluster > 16-bits
> virtio-net: fix ring handling in receive
> net: Remove remainders of the MTFTP code
> net: Move also files from clients/net-snk/app/netapps/ to lib/libnet/
> net: Move files from clients/net-snk/app/netlib/ to lib/libnet/
> net-snk: Get rid of netlib and netapps prefixes in include statements
> usb-xhci: assign field4 before conditional
> Improve F12 key handling in boot menu
> Fix stack underflow that occurs with duplicated ESC in input
> rtas-nvram: optimize erase
> ipv6: Replace magic number 1500 with ETH_MTU_SIZE (i.e. 1518)
> ipv6: Fix NULL pointer dereference in ip6addr_add()
> ipv6: Fix memory leak in set_ipv6_address() / ip6_create_ll_address()
> ipv6: Clear memory after malloc if necessary
> ipv6: Fix possible NULL-pointer dereference in send_ipv6()
> ping: use gateway address for routing
> ping: add netmask in the ping argument
> xhci: fix missing keys from keyboard
> xhci: add memory barrier after filling the trb
> loaders: Remove netflash command
> boot: Remove legacy Forth words for network loading
> base: Move cnt-bits and bcd-to-bin to board-js2x folder
> base: Move huge-tftp-load variable to obp-tftp package
> base: Remove unused IP address conversion functions
> virtio: White space cleanup in virtio-9p.c
> virtio: Add modern version 1.0 support to 9p driver
> virtio: Set a proper name for virtio-9p device tree nodes
> pci: Fix mistype in "unkown-bridge"
> ipv6: Indent code with tabs, not with spaces
> ipv6: send_ipv6() has to return after doing NDP
> ipv6: Do not use unitialized MAC address array
> ipv6: Add support for sending packets through a router
> Remove unused sms code.
> virtio-net: initialize to populate mac address
> libbootmsg: Do not use '\b' characters when printing checkpoints
> dev-null: The "read" function has to return 0 if nothing has been read
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
