In the previous patch which introduced fprintf_function to
allow parameter checking by gcc some compiler warnings
remained unfixed.
These warnings are fixed here.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
QEMU uses a fixed page size for the CPU TLB. If the guest uses large
pages then we effectively split these into multiple smaller pages, and
populate the corresponding TLB entries on demand.
When the guest invalidates the TLB by virtual address we must invalidate
all entries covered by the large page. However the address used to
invalidate the entry may not be present in the QEMU TLB, so we do not
know which regions to clear.
Implementing a full vaiable size TLB is hard and slow, so just keep a
simple address/mask pair to record which addresses may have been mapped by
large pages. If the guest invalidates this region then flush the
whole TLB.
Signed-off-by: Paul Brook <paul@codesourcery.com>
Removes a set of ifdefs from exec.c.
Introduce TARGET_VIRT_ADDR_SPACE_BITS for all targets other
than Alpha. This will be used for page_find_alloc, which is
supposed to be using virtual addresses in the first place.
Signed-off-by: Richard Henderson <rth@twiddle.net>
When we signal a CpU exception for coprocessor 0, we should indicate
that it's for coprocessor 0 instead of coprocessor 1.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
In helper.c AREG0 may not correspond do env, so it's not possible to
call cpu_loop_exit() here. Call it from op_helper.c instead.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Fix regression introduced by d19954f46d.
4Kc and 4KEc don't support MIPS16.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
4Kc, 4KEc cores do not support MIPS16, so not only the
CP0_Config1 had to be fixed (see previous patch),
but also MIPS16 instructions must not be executed.
(Hint from Nathan Froyd, thanks).
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Running programs with the MIPS user-mode emulator fails during dynamic
loading, as floating-point instructions are not enabled in in
env->hflags. Move the code for doing so from fpu_init to cpu_reset so
the MIPS_HFLAG_{FPU,F64} setting doesn't get clobbered by cpu_reset
setting env->hflags to MIPS_HFLAG_UM.
The same end can be achieved by swapping the ordering of fpu_init and
cpu_reset in cpu_mips_init, but it seemed better to consolidate the
CONFIG_USER_ONLY code into a single location.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
There's no good way to add this incrementally, so we do it all at once.
The only changes to shared code are in handle_delay_slot. We need to
flip ISAMode when doing a jump-and-exchange. We also need to set
ISAMode the low bit of the target address for jump-to-register.
Also, since we're now adding bits that can be in MIPS_HFLAG_BMASK_EXT,
make sure we use MIPS_HFLAG_BMASK_BASE in the places where we just want
basic information about a branch.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Move delay slot handling to common code whose invocation can be
controlled from gen_intermediate_code_internal.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This is a common pattern in existing code. We'll also use it to
implement the mips16 SAVE/RESTORE instructions.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
It's easier to implement mips16 shift instructions if we're not
examining the opcode inside gen_shift_{imm,}. So move ROTR and ROTRV
and do the special-case handling of SRL and SRLV inside decode_opc.
Likewise for their 64-bit counterparts.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
We need to stash the operating mode into the low bit of the error PC and
restore it on return from interrupts.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
We create separate masks for the "basic" branch hflags and the
"extended" branch hflags and define MIPS_HFLAG_BMASK as the logical or
of those two. This is done to avoid churning the codebase in lots of
different places.
We also make the execution mode an hflag under MIPS_HFLAG_TMASK
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Currently the ll/sc instructions use the virtual address in both
user and system mode. Use the physical address insteead in system
mode.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Depending on the CPU, CP0_LLAddr is either read-only or read-write,
and the returned value can be shifted by a variable amount of bits.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
The variable CP0_LLAddr represent the full lladdr, not the actual
register value, which is only part of this value and depends on the
CPU.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Remove cpu_mips_register()
- move mmu_init(), fpu_init() and mvp_init() into cpu_mips_init()
- move the other parts in cpu_mips_init()
Reported-by: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
In the very least, a change like this requires discussion on the list.
The naming convention is goofy and it causes a massive merge problem. Something
like this _must_ be presented on the list first so people can provide input
and cope with it.
This reverts commit 99a0949b72.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Now that MAX_OP_PER_INSTR has been increased to a safer value, removed
the target-mips specific workaround.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Single-stepping branches on MIPS didn't work right, because the
generation of EXCP_DEBUG happened after the generation of the code to
exit the current TB. That is, given the code:
bne v0,v1,target
nop
...
target:
addu v0,v0,v1
1:
when you single-stepped through the NOP, execution wouldn't actually
halt until you reached the label `1'.
This patch corrects that and also changes single-stepping so that a
branch and its delay slot are executed as one instruction for the
purposes of single-stepping. This behavior is comparable to what other
MIPS tools (e.g. MIPSsim with MDI) do. GDB avoids placing breakpoints
in branch delay slots, so this change doesn't break anything on the GDB
side.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Problem: Our file sys-queue.h is a copy of the BSD file, but there are
some additions and it's not entirely compatible. Because of that, there have
been conflicts with system headers on BSD systems. Some hacks have been
introduced in the commits 15cc923584,
f40d753718,
96555a96d7 and
3990d09adf but the fixes were fragile.
Solution: Avoid the conflict entirely by renaming the functions and the
file. Revert the previous hacks.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Conditional moves off fp condition codes were using the result of
get_fp_bit to isolate and test the relevant condition code. However,
get_fp_bit returns the bit number of the condition code, not a
bitmask. (Compare the use of get_fp_bit in gen_compute_branch1, for
instance.)
Fixed by shifting a bitmask into place using the result of get_fp_bit in
the relevant functions (gen_mov{ci,cf_s,cf_d,cf_ps}).
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
handle_cpu_signal is very nearly copy-paste code for each target, with a
few minor variations. This patch sets up appropriate defaults for a
generic handle_cpu_signal and provides overrides for particular targets
that did things differently. Fixing things like the persistent (XXX:
use sigsetjmp) should now become somewhat easier.
Previous comments on this patch suggest that the "activate soft MMU for
this block" comments refer to defunct functionality. I have removed
such blocks for the appropriate targets in this patch.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
