Use FIELD macros to handle CTEs, rather than ad-hoc mask-and-shift.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The comment says that in our CTE format the RDBase field is 36 bits;
in fact for us it is only 16 bits, because we use the RDBase format
where it specifies a 16-bit CPU number. The code already uses
RDBASE_PROCNUM_LENGTH (16) as the field width, so fix the comment
to match it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Currently the ITS code that reads and writes DTEs uses open-coded
shift-and-mask to assemble the various fields into the 64-bit DTE
word. The names of the macros used for mask and shift values are
also somewhat inconsistent, and don't follow our usual convention
that a MASK macro should specify the bits in their place in the word.
Replace all these with use of the FIELD macro.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The MAPI command takes arguments DeviceID, EventID, ICID, and is
defined to be equivalent to MAPTI DeviceID, EventID, EventID, ICID.
(That is, where MAPTI takes an explicit pINTID, MAPI uses the EventID
as the pINTID.)
We didn't quite get this right. In particular the error checks for
MAPI include "EventID does not specify a valid LPI identifier", which
is the same as MAPTI's error check for the pINTID field. QEMU's code
skips the pINTID error check entirely in the MAPI case.
We can fix this bug and in the process simplify the code by switching
to the obvious implementation of setting pIntid = eventid early
if ignore_pInt is true.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The GITS_TYPE_PHYSICAL define is the value we set the
GITS_TYPER.Physical field to -- this is 1 to indicate that we support
physical LPIs. (Support for virtual LPIs is the GITS_TYPER.Virtual
field.) We also use this define as the *value* that we write into an
interrupt translation table entry's INTTYPE field, which should be 1
for a physical interrupt and 0 for a virtual interrupt. Finally, we
use it as a *mask* when we read the interrupt translation table entry
INTTYPE field.
Untangle this confusion: define an ITE_INTTYPE_VIRTUAL and
ITE_INTTYPE_PHYSICAL to be the valid values of the ITE INTTYPE
field, and replace the ad-hoc collection of ITE_ENTRY_* defines with
use of the FIELD() macro to define the fields of an ITE and the
FIELD_EX64() and FIELD_DP64() macros to read and write them.
We use ITE in the new setup, rather than ITE_ENTRY, because
ITE stands for "Interrupt translation entry" and so the extra
"entry" would be redundant.
We take the opportunity to correct the name of the field that holds
the GICv4 'doorbell' interrupt ID (this is always the value 1023 in a
GICv3, which is why we were calling it the 'spurious' field).
The GITS_TYPE_PHYSICAL define is then used in only one place, where
we set the initial GITS_TYPER value. Since GITS_TYPER.Physical is
essentially a boolean, hiding the '1' value behind a macro is more
confusing than helpful, so expand out the macro there and remove the
define entirely.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
We set the TableDesc entry_sz field from the appropriate
GITS_BASER.ENTRYSIZE field. That ID register field specifies the
number of bytes per table entry minus one. However when we use
td->entry_sz we assume it to be the number of bytes per table entry
(for instance we calculate the number of entries in a page by
dividing the page size by the entry size).
The effects of this bug are:
* we miscalculate the maximum number of entries in the table,
so our checks on guest index values are wrong (too lax)
* when looking up an entry in the second level of an indirect
table, we calculate an incorrect index into the L2 table.
Because we make the same incorrect calculation on both
reads and writes of the L2 table, the guest won't notice
unless it's unlucky enough to use an index value that
causes us to index off the end of the L2 table page and
cause guest memory corruption in whatever follows
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The extract_table_params() decodes the fields in the GITS_BASER<n>
registers into TableDesc structs. Since the fields are the same for
all the GITS_BASER<n> registers, there is currently a lot of code
duplication within the switch (type) statement. Refactor so that the
cases include only what is genuinely different for each type:
the calculation of the number of bits in the ID value that indexes
into the table.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
In extract_table_params() we process each GITS_BASER<n> register. If
the register's Valid bit is not set, this means there is no
in-guest-memory table and so we should not try to interpret the other
fields in the register. This was incorrectly coded as a 'return'
rather than a 'break', so instead of looping round to process the
next GITS_BASER<n> we would stop entirely, treating any later tables
as being not valid also.
This has no real guest-visible effects because (since we don't have
GITS_TYPER.HCC != 0) the guest must in any case set up all the
GITS_BASER<n> to point to valid tables, so this only happens in an
odd misbehaving-guest corner case.
Fix the check to 'break', so that we leave the case statement and
loop back around to the next GITS_BASER<n>.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The TableDesc struct defines properties of the in-guest-memory tables
which the guest tells us about by writing to the GITS_BASER<n>
registers. This struct currently has a union 'maxids', but all the
fields of the union have the same type (uint32_t) and do the same
thing (record one-greater-than the maximum ID value that can be used
as an index into the table).
We're about to add another table type (the GICv4 vPE table); rather
than adding another specifically-named union field for that table
type with the same type as the other union fields, remove the union
entirely and just have a 'uint32_t max_ids' struct field.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
We currently define a bitmask for the GITS_CTLR ENABLED bit in
two ways: as ITS_CTLR_ENABLED, and via the FIELD() macro as
R_GITS_CTLR_ENABLED_MASK. Consistently use the FIELD macro version
everywhere and remove the redundant ITS_CTLR_ENABLED define.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The checks in the ITS on the rdbase values in guest commands are
off-by-one: they permit the guest to pass us a value equal to
s->gicv3->num_cpu, but the valid values are 0...num_cpu-1. This
meant the guest could cause us to index off the end of the
s->gicv3->cpu[] array when calling gicv3_redist_process_lpi(), and we
would probably crash.
(This is not a security bug, because this code is only usable
with emulation, not with KVM.)
Cc: qemu-stable@nongnu.org
Fixes: 17fb5e36aa ("hw/intc: GICv3 redistributor ITS processing")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
dma_memory_read() returns a MemTxResult type. Do not discard
it, return it to the caller.
Update the few callers.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211223115554.3155328-19-philmd@redhat.com>
Let devices specify transaction attributes when calling ld*_dma().
Keep the default MEMTXATTRS_UNSPECIFIED in the few callers.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211223115554.3155328-17-philmd@redhat.com>
Let devices specify transaction attributes when calling
dma_memory_rw().
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20211223115554.3155328-5-philmd@redhat.com>
The TYPE_ARM_GICV3 device is an emulated one. When using
KVM, it is recommended to use the TYPE_KVM_ARM_GICV3 device
(which uses in-kernel support).
When using --with-devices-FOO, it is possible to build a
binary with a specific set of devices. When this binary is
restricted to KVM accelerator, the TYPE_ARM_GICV3 device is
irrelevant, and it is desirable to remove it from the binary.
Therefore introduce the CONFIG_ARM_GIC_TCG Kconfig selector
which select the files required to have the TYPE_ARM_GICV3
device, but also allowing to de-select this device.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20211115223619.2599282-3-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
gicv3_set_gicv3state() is used by arm_gicv3_common.c in
arm_gicv3_common_realize(). Since we want to restrict
arm_gicv3_cpuif.c to TCG, extract gicv3_set_gicv3state()
to a new file. Add this file to the meson 'specific'
source set, since it needs access to "cpu.h".
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20211115223619.2599282-2-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
While trying to debug a GIC ITS failure I saw some guest errors that
had poor formatting as well as leaving me confused as to what failed.
As most of the checks aren't possible without a valid dte split that
check apart and then check the other conditions in steps. This avoids
us relying on undefined data.
I still get a failure with the current kvm-unit-tests but at least I
know (partially) why now:
Exception return from AArch64 EL1 to AArch64 EL1 PC 0x40080588
PASS: gicv3: its-trigger: inv/invall: dev2/eventid=20 now triggers an LPI
ITS: MAPD devid=2 size = 0x8 itt=0x40430000 valid=0
INT dev_id=2 event_id=20
process_its_cmd: invalid command attributes: invalid dte: 0 for 2 (MEM_TX: 0)
PASS: gicv3: its-trigger: mapd valid=false: no LPI after device unmap
SUMMARY: 6 tests, 1 unexpected failures
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20211112170454.3158925-1-alex.bennee@linaro.org
Cc: Shashi Mallela <shashi.mallela@linaro.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
According to the "Arm Generic Interrupt Controller Architecture
Specification GIC architecture version 3 and 4" (version G: page 345
for aarch64 or 509 for aarch32):
LRENP bit of ICH_MISR is set when ICH_HCR.LRENPIE==1 and
ICH_HCR.EOIcount is non-zero.
When only LRENPIE was set (and EOI count was zero), the LRENP bit was
wrongly set and MISR value was wrong.
As an additional consequence, if an hypervisor set ICH_HCR.LRENPIE,
the maintenance interrupt was constantly fired. It happens since patch
9cee1efe92 ("hw/intc: Set GIC maintenance interrupt level to only 0 or 1")
which fixed another bug about maintenance interrupt (most significant
bits of misr, including this one, were ignored in the interrupt trigger).
Fixes: 83f036fe3d ("hw/intc/arm_gicv3: Add accessors for ICH_ system registers")
Signed-off-by: Damien Hedde <damien.hedde@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20211207094427.3473-1-damien.hedde@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It is valid for an OS to put virtual interrupt ID values into the
list registers ICH_LR<n> which are greater than 1023. This
corresponds to (for example) KVM using the in-kernel emulated ITS to
give a (nested) guest an ITS. LPIs are delivered by the L1 kernel to
the L2 guest via the list registers in the same way as non-LPI
interrupts.
QEMU's code for handling writes to ICV_IARn (which happen when the L2
guest acknowledges an interrupt) and to ICV_EOIRn (which happen at
the end of the interrupt) did not consider LPIs, so it would
incorrectly treat interrupt IDs above 1023 as invalid. Fix this by
using the correct condition, which is gicv3_intid_is_special().
Note that the condition in icv_dir_write() is correct -- LPIs
are not valid there and so we want to ignore both "special" ID
values and LPIs.
(In the pseudocode this logic is in:
- VirtualReadIAR0(), VirtualReadIAR1(), which call IsSpecial()
- VirtualWriteEOIR0(), VirtualWriteEOIR1(), which call
VirtualIdentifierValid(data, TRUE) meaning "LPIs OK"
- VirtualWriteDIR(), which calls VirtualIdentifierValid(data, FALSE)
meaning "LPIs not OK")
This bug doesn't seem to have any visible effect on Linux L2 guests
most of the time, because the two bugs cancel each other out: we
neither mark the interrupt active nor deactivate it. However it does
mean that the L2 vCPU priority while the LPI handler is running will
not be correct, so the interrupt handler could be unexpectedly
interrupted by a different interrupt.
(NB: this has nothing to do with using QEMU's emulated ITS.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
The GICv3/v4 pseudocode has a function IsSpecial() which returns true
if passed a "special" interrupt ID number (anything between 1020 and
1023 inclusive). We open-code this condition in a couple of places,
so abstract it out into a new function gicv3_intid_is_special().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
The logic of gicv3_redist_update() is as follows:
* it must be called in any code path that changes the state of
(only) redistributor interrupts
* if it finds a redistributor interrupt that is (now) higher
priority than the previous highest-priority pending interrupt,
then this must be the new highest-priority pending interrupt
* if it does *not* find a better redistributor interrupt, then:
- if the previous state was "no interrupts pending" then
the new state is still "no interrupts pending"
- if the previous best interrupt was not a redistributor
interrupt then that remains the best interrupt
- if the previous best interrupt *was* a redistributor interrupt,
then the new best interrupt must be some non-redistributor
interrupt, but we don't know which so must do a full scan
In commit 17fb5e36aa we effectively added the LPI interrupts
as a kind of "redistributor interrupt" for this purpose, by adding
cs->hpplpi to the set of things that gicv3_redist_update() considers
before it gives up and decides to do a full scan of distributor
interrupts. However we didn't quite get this right:
* the condition check for "was the previous best interrupt a
redistributor interrupt" must be updated to include LPIs
in what it considers to be redistributor interrupts
* every code path which updates the LPI state which
gicv3_redist_update() checks must also call gicv3_redist_update():
this is cs->hpplpi and the GICR_CTLR ENABLE_LPIS bit
This commit fixes this by:
* correcting the test on cs->hppi.irq in gicv3_redist_update()
* making gicv3_redist_update_lpi() always call gicv3_redist_update()
* introducing a new gicv3_redist_update_lpi_only() for the one
callsite (the post-load hook) which must not call
gicv3_redist_update()
* making gicv3_redist_lpi_pending() always call gicv3_redist_update(),
either directly or via gicv3_redist_update_lpi()
* removing a couple of now-unnecessary calls to gicv3_redist_update()
from some callers of those two functions
* calling gicv3_redist_update() when the GICR_CTLR ENABLE_LPIS
bit is cleared
(This means that the not-file-local gicv3_redist_* LPI related
functions now all take care of the updates of internally cached
GICv3 information, in the same way the older functions
gicv3_redist_set_irq() and gicv3_redist_send_sgi() do.)
The visible effect of this bug was that when the guest acknowledged
an LPI by reading ICC_IAR1_EL1, we marked it as not pending in the
LPI data structure but still left it in cs->hppi so we would offer it
to the guest again. In particular for setups using an emulated GICv3
and ITS and using devices which use LPIs (ie PCI devices) a Linux
guest would complain "irq 54: nobody cared" and then hang. (The hang
was intermittent, presumably depending on the timing between
different interrupts arriving and being completed.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20211124202005.989935-1-peter.maydell@linaro.org
When Enabled bit is cleared in GITS_CTLR,ITS feature continues
to be enabled.This patch fixes the issue.
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20211124182246.67691-1-shashi.mallela@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit 18f6290a6a ("hw/intc: GICv3 ITS initial framework")
incremented version_id and minimum_version_id fields of
VMStateDescription vmstate_its. This breaks the migration between
6.2 and 6.1 with the following message:
qemu-system-aarch64: savevm: unsupported version 1 for 'arm_gicv3_its' v0
qemu-system-aarch64: load of migration failed: Invalid argument
Revert that change.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20211122171020.1195483-1-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Our GICv3 QOM interface includes an array property
redist-region-count which allows board models to specify that the
registributor registers are not in a single contiguous range, but
split into multiple pieces. We implemented this for KVM, but
currently the TCG GICv3 model insists that there is only one region.
You can see the limit being hit with a setup like:
qemu-system-aarch64 -machine virt,gic-version=3 -smp 124
Add support for split regions to the TCG GICv3. To do this we switch
from allocating a simple array of MemoryRegions to an array of
GICv3RedistRegion structs so that we can use the GICv3RedistRegion as
the opaque pointer in the MemoryRegion read/write callbacks. Each
GICv3RedistRegion contains the MemoryRegion, a backpointer allowing
the read/write callback to get hold of the GICv3State, and an index
which allows us to calculate which CPU's redistributor is being
accessed.
Note that arm_gicv3_kvm always passes in NULL as the ops argument
to gicv3_init_irqs_and_mmio(), so the only MemoryRegion read/write
callbacks we need to update to handle this new scheme are the
gicv3_redist_read/write functions used by the emulated GICv3.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The 'Last' bit in the GICR_TYPER GICv3 redistributor register is
supposed to be set to 1 if this is the last redistributor in a series
of contiguous redistributor pages. Currently we set Last only for
the redistributor for CPU (num_cpu - 1). This only works if there is
a single redistributor region; if there are multiple redistributor
regions then we need to set the Last bit for the last redistributor
in each region.
This doesn't cause any problems currently because only the KVM GICv3
supports multiple redistributor regions, and it ignores the value in
GICv3State::gicr_typer. But we need to fix this before we can enable
support for multiple regions in the emulated GICv3.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The GICv3 devices have an array property redist-region-count.
Currently we check this for errors (bad values) in
gicv3_init_irqs_and_mmio(), just before we use it. Move this error
checking to the arm_gicv3_common_realize() function, where we
sanity-check all of the other base-class properties. (This will
always be before gicv3_init_irqs_and_mmio() is called, because
that function is called in the subclass realize methods, after
they have called the parent-class realize.)
The motivation for this refactor is:
* we would like to use the redist_region_count[] values in
arm_gicv3_common_realize() in a subsequent patch, so we need
to have already done the sanity-checking first
* this removes the only use of the Error** argument to
gicv3_init_irqs_and_mmio(), so we can remove some error-handling
boilerplate
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The sh_intc_locate function will either init these or not return so no
need to initialise them.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <15e04aa665c68ab5df47bbf505346d413be2fc1c.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Use g_new0 instead of g_malloc0 and avoid some unneeded temporary
variable assignments.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <72efc4f2c4ff8b96848d03dca08e4541ee4076f6.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Instead of if !expr continue else do something it is more straight
forward to say if expr then do something, especially if the action is
just a few lines. Remove such uses of continue to make the code easier
to follow.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <0efaa5e7a1a3ee11f82b3bb1942c287576c67f8b.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
All the places that call abort should not happen which is better
marked by g_assert_not_reached.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <039e6a784532f2af27f8adeafdb8e0391722f567.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This function is very simple and provides no advantage. Call sites
become simpler without it so just write it in line and drop the
separate function.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <a98d1f7f94e91a42796b7d91e9153a7eaa3d1c44.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Address of element i is one word thus clearer than array + i.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <f49c9b1dee1fcaf374b092d862a6821907d5fcdc.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Drop unneded parenthesis and split up one complex expression to write
it with less brackets so it's easier to follow.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <a48e849e5b803a952ed15a2502cfece2bde68934.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The sh_intc_register() function is only used at one place. Move them
together so it's easier to see what's going on.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <49f2742bc67cba7164385fafad204ab1e1bd3a0b.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The INT_REG_PARAMS macro was only used a few times within one function
on adjacent lines and is actually more complex than writing out the
parameters so simplify it by expanding the macro at call sites and
dropping the #define.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <d3bdfdc5ab5ae1c51a6c6c38bde3829a99f85ce5.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Rename the iomem region to "intc" from "interrupt-controller" which
makes the info mtree output less wide as it is already too wide
because of all the aliases. Also drop the format macro which was only
used twice in close proximity so we can just use the literal string
instead without a macro definition.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <cb6402dab6b44c804142b5cf9af68e6398cb613f.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Turn the INTC_MODE defines into an enum and clean up the function
returning these to make it clearer by removing nested ifs and
superfluous parenthesis. The one remaining #define is a flag which is
moved further apart by changing its value from 8 to 0x80 to leave some
spare bits as this is or-ed with the enum value at some places.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <4adf4e1ac9d2e728e5a536c69e310d77f0c4455a.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The INTC_A7 local macro does the same as the A7ADDR from
include/sh/sh.h so use the latter and drop the local macro definition.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <53f033477c73b7c9b021d36033c590416d6199c7.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
xive_esb_rw() is the common routine used for memory accesses on ESB
page. Use it for triggers also.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211006210546.641102-1-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
