Currently the serial.c realize code has an explicit check that it is not
connected to a disconnected backend (ie one with a NULL chardev).
This isn't what we want -- you should be able to create a serial device
even if it isn't attached to anything. Remove the check.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180420145249.32435-2-peter.maydell@linaro.org
The CMSDK APB UART INTSTATUS register bits are all write-one-to-clear.
We were getting this correct for the TXO and RXO bits (which need
special casing because their state lives in the STATE register),
but had forgotten to handle the normal bits for RX and TX which
we do store in our s->intstatus field.
Perform the W1C operation on the bits in s->intstatus too.
Fixes: https://bugs.launchpad.net/qemu/+bug/1760262
Cc: qemu-stable@nongnu.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180410134203.17552-1-peter.maydell@linaro.org
Check device having the feature of VIRTIO_CONSOLE_F_EMERG_WRITE before
get config->emerg_wr. It is neccessary because sizeof(virtio_console_config)
is 8 byte if VirtIOSerial doesn't have the feature of
VIRTIO_CONSOLE_F_EMERG_WRITE(see virtio_serial_device_realize),
read/write emerg_wr will lead to heap-over-flow.
Signed-off-by: linzhecheng <linzhecheng@huawei.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Linux does not detect a break from this IMX serial driver as a magic
sysrq. Nor does it note a break in the port error counts.
The former is because the Linux driver uses the BRCD bit in the USR2
register to trigger the RS-232 break handler in the kernel, which is
where sysrq hooks in. The emulated UART was not setting this status
bit.
The latter is because the Linux driver expects, in addition to the BRK
bit, that the ERR bit is set when a break is read in the FIFO. A break
should also count as a frame error, so add that bit too.
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Message-id: 20180320013657.25038-1-tpiepho@impinj.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for "TX complete"/TXDC interrupt generate by real HW since
it is needed to support guests other than Linux.
Based on the patch by Bill Paul as found here:
https://bugs.launchpad.net/qemu/+bug/1753314
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Cc: Bill Paul <wpaul@windriver.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Bill Paul <wpaul@windriver.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Message-id: 20180315191141.6789-2-andrew.smirnov@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Code of imx_update() is slightly confusing since the "flags" variable
doesn't really corespond to anything in real hardware and server as a
kitchensink accumulating events normally reported via USR1 and USR2
registers.
Change the code to explicitly evaluate state of interrupts reported
via USR1 and USR2 against corresponding masking bits and use the to
detemine if IRQ line should be asserted or not.
NOTE: Check for UTS1_TXEMPTY being set has been dropped for two
reasons:
1. Emulation code implements a single character FIFO, so this flag
will always be set since characters are trasmitted as a part of
the code emulating "push" into the FIFO
2. imx_update() is really just a function doing ORing and maksing
of reported events, so checking for UTS1_TXEMPTY should happen,
if it's ever really needed should probably happen outside of
it.
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Cc: Bill Paul <wpaul@windriver.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Message-id: 20180315191141.6789-1-andrew.smirnov@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Again... (after 07dc788054 and 9157eee1b1).
We now extract the ISA bus specific helpers.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180308223946.26784-2-f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Introduce an sccb_mask_t to be used for SCLP event masks instead of just
unsigned int or uint32_t. This will allow later to extend the mask with
more ease.
Signed-off-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Message-Id: <1519407778-23095-3-git-send-email-imbrenda@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The other event handlers (quiesce and cpu) do not define these
handlers, and this one does nothing, so it can be removed.
Signed-off-by: Nia Alarie <nia.alarie@gmail.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <20180306100721.19419-1-nia.alarie@gmail.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
In my "build everything" tree, a change to the types in
qapi-schema.json triggers a recompile of about 4800 out of 5100
objects.
The previous commit split up qmp-commands.h, qmp-event.h, qmp-visit.h,
qapi-types.h. Each of these headers still includes all its shards.
Reduce compile time by including just the shards we actually need.
To illustrate the benefits: adding a type to qapi/migration.json now
recompiles some 2300 instead of 4800 objects. The next commit will
improve it further.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180211093607.27351-24-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
[eblake: rebase to master]
Signed-off-by: Eric Blake <eblake@redhat.com>
I/O currently being synchronous, there is no reason to ever clear the
SR_TXE bit. However the SR_TC bit may be cleared by software writing
to the SR register, so set it on each write.
In addition, fix the reset value of the USART status register.
Signed-off-by: Richard Braun <rbraun@sceen.net>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
[PMM: removed XXX tag from comment, since it isn't something
we need to come back and fix in QEMU]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move necessary stuff in escc.h and update type names.
Remove slavio_serial_ms_kbd_init().
Fix code style problems reported by checkpatch.pl
Update mac_newworld, mac_oldworld and sun4m to use directly the
QDEV interface.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This cleanup makes the number of objects depending on qapi/error.h
drop from 1910 (out of 4743) to 1612 in my "build everything" tree.
While there, separate #include from file comment with a blank line,
and drop a useless comment on why qemu/osdep.h is included first.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-5-armbru@redhat.com>
[Semantic conflict with commit 34e304e975 resolved, OSX breakage fixed]
Replace the qcode_to_keycode table with automatically
generated tables.
Missing entries in qcode_to_keycode now fixed:
- Q_KEY_CODE_KP_COMMA -> 0x2d
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20180117164118.8510-3-berrange@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The point of writing a macro embedded in a 'do { ... } while (0)'
loop (particularly if the macro has multiple statements or would
otherwise end with an 'if' statement) is so that the macro can be
used as a drop-in statement with the caller supplying the
trailing ';'. Although our coding style frowns on brace-less 'if':
if (cond)
statement;
else
something else;
that is the classic case where failure to use do/while(0) wrapping
would cause the 'else' to pair with any embedded 'if' in the macro
rather than the intended outer 'if'. But conversely, if the macro
includes an embedded ';', then the same brace-less coding style
would now have two statements, making the 'else' a syntax error
rather than pairing with the outer 'if'. Thus, even though our
coding style with required braces is not impacted, ending a macro
with ';' makes our code harder to port to projects that use
brace-less styles.
The change should have no semantic impact. I was not able to
fully compile-test all of the changes (as some of them are
examples of the ugly bit-rotting debug print statements that are
completely elided by default, and I didn't want to recompile
with the necessary -D witnesses - cleaning those up is left as a
bite-sized task for another day); I did, however, audit that for
all files touched, all callers of the changed macros DID supply
a trailing ';' at the callsite, and did not appear to be used
as part of a brace-less conditional.
Found mechanically via: $ git grep -B1 'while (0);' | grep -A1 \\\\
Signed-off-by: Eric Blake <eblake@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20171201232433.25193-7-eblake@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It's a replacement of g_timeout_add[_seconds]() for chardevs. Chardevs
now can have dedicated gcontext, we should always bind chardev tasks
onto those gcontext rather than the default main context. Since there
are quite a few of g_timeout_add[_seconds]() callers, a new function
qemu_chr_timeout_add_ms() is introduced.
One thing to mention is that, terminal3270 is still always running on
main gcontext. However let's convert that as well since it's still part
of chardev codes and in case one day we'll miss that when we move it out
of main gcontext too.
Also, convert all the timers from GSource tags into GSource pointers.
Gsource tag IDs and g_source_remove()s can only work with default
gcontext, while now these GSources can logically be attached to other
contexts. So let's use explicit g_source_destroy() plus another
g_source_unref() to remove a timer.
Note: when in the timer handler, we don't need the g_source_destroy()
any more since that'll be done automatically if the timer handler
returns false (and that's what all the current handlers do).
Yet another note: in pty_chr_rearm_timer() we take special care for
ms=1000. This patch merged the two cases into one.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180104141835.17987-4-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
exec: housekeeping (funny since 02d0e09503)
applied using ./scripts/clean-includes
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The spapr-vty device implements the PAPR defined virtual console,
which is also implemented by IBM's proprietary PowerVM hypervisor.
PowerVM's implementation has a bug where it inserts an extra \0 after
every \r going to the guest. Because of that Linux's guest side
driver has a workaround which strips \0 characters that appear
immediately after a \r.
That means that when running under qemu, sending a binary stream from
host to guest via spapr-vty which happens to include a \r\0 sequence
will get corrupted by that workaround.
To deal with that, this patch duplicates PowerVM's bug, inserting an
extra \0 after each \r. Ugly, but the best option available.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Some drivers for the PPMC7400 PowerPC evaluation board accesses the
serial registers through the floating point unit (stfd/ldfd), which is
an 8-byte wide access. This patch enables that behavior.
Signed-off-by: Mike Nawrocki <michael.nawrocki@gtri.gatech.edu>
Message-Id: <20171106161039.32596-1-michael.nawrocki@gtri.gatech.edu>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add INTERFACE_CONVENTIONAL_PCI_DEVICE to all direct subtypes of
TYPE_PCI_DEVICE, except:
1) The ones that already have INTERFACE_PCIE_DEVICE set:
* base-xhci
* e1000e
* nvme
* pvscsi
* vfio-pci
* virtio-pci
* vmxnet3
2) base-pci-bridge
Not all PCI bridges are Conventional PCI devices, so
INTERFACE_CONVENTIONAL_PCI_DEVICE is added only to the subtypes
that are actually Conventional PCI:
* dec-21154-p2p-bridge
* i82801b11-bridge
* pbm-bridge
* pci-bridge
The direct subtypes of base-pci-bridge not touched by this patch
are:
* xilinx-pcie-root: Already marked as PCIe-only.
* pcie-pci-bridge: Already marked as PCIe-only.
* pcie-port: all non-abstract subtypes of pcie-port are already
marked as PCIe-only devices.
3) megasas-base
Not all megasas devices are Conventional PCI devices, so the
interface names are added to the subclasses registered by
megasas_register_types(), according to information in the
megasas_devices[] array.
"megasas-gen2" already implements INTERFACE_PCIE_DEVICE, so add
INTERFACE_CONVENTIONAL_PCI_DEVICE only to "megasas".
Acked-by: Alberto Garcia <berto@igalia.com>
Acked-by: John Snow <jsnow@redhat.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The problem is, that the current implementation places unrealistic and
arbitrary constraints on the length of writes to the device (that is the
outbound requests), by asserting ccw.count being such that that even the
worst case escaped payload will fit an more or less arbitrary sized
buffer. Actually on protocol level there is nothing to justify such
a limitation.
Another strange thing is the return value which more or less reflects
the size (written) after escaping instead of before escaping. This
is strange, because this return value is used to calculate SCSW.count.
Let us teach 3270 how to deal with arbitrary long writes.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Reported-by: Jason J . Herne <jjherne@linux.vnet.ibm.com>
Tested-by: Jason J . Herne <jjherne@linux.vnet.ibm.com>
Message-Id: <20170920172314.102710-3-pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Let us convert the 3270 code so it uses the recently introduced
CcwDataStream abstraction instead of blindly assuming direct data access.
This patch does not change behavior beyond introducing IDA support: for
direct data access CCWs everything stays as-is. (If there are bugs, they
are also preserved).
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Message-Id: <20170920172314.102710-2-pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Modify the pre_save method on VMStateDescription to return an int
rather than void so that it potentially can fail.
Changed zillions of devices to make them return 0; the only
case I've made it return non-0 is hw/intc/s390_flic_kvm.c that already
had an error_report/return case.
Note: If you add an error exit in your pre_save you must emit
an error_report to say why.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20170925112917.21340-2-dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
We should guarantee that RAM will not be modified while VM has a stopped
state, otherwise it can lead to negative consequences during post-copy
migration. In RUN_STATE_FINISH_MIGRATE step, it's expected that RAM on
source side will not be modified as this could lead to non-consistent vm state
on the destination side. Also RAM access during postcopy-ram migration with
enabled release-ram capability can lead to sad consequences.
Let's add enable_backend() callback to avoid undesirable virtioqueue changes
in the guest memory.
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Message-Id: <20170919120733.22020-1-pbutsykin@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
I used the clang-tidy qemu-round check to generate the fix:
https://github.com/elmarco/clang-tools-extra
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Amit Shah <amit@kernel.org>
The only exception are groups of numers separated by symbols
'.', ' ', ':', '/', like 'ab.09.7d'.
This patch is made by the following:
> find . -name trace-events | xargs python script.py
where script.py is the following python script:
=========================
#!/usr/bin/env python
import sys
import re
import fileinput
rhex = '%[-+ *.0-9]*(?:[hljztL]|ll|hh)?(?:x|X|"\s*PRI[xX][^"]*"?)'
rgroup = re.compile('((?:' + rhex + '[.:/ ])+' + rhex + ')')
rbad = re.compile('(?<!0x)' + rhex)
files = sys.argv[1:]
for fname in files:
for line in fileinput.input(fname, inplace=True):
arr = re.split(rgroup, line)
for i in range(0, len(arr), 2):
arr[i] = re.sub(rbad, '0x\g<0>', arr[i])
sys.stdout.write(''.join(arr))
=========================
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Message-id: 20170731160135.12101-5-vsementsov@virtuozzo.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
With the move of some docs/ to docs/devel/ on ac06724a71,
no references were updated.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The right alt key (alt_r aka KEY_RIGHTALT) is used for AltGr.
The altgr and altgr_r keys simply don't exist. Drop them.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20170727104720.30061-1-kraxel@redhat.com
Add the UARTs to the MPS2 board models.
Unfortunately the details of the wiring of the interrupts through
various OR gates differ between AN511 and AN385 so this can't
be purely a data-driven difference.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1500029487-14822-4-git-send-email-peter.maydell@linaro.org
Implement a model of the simple "APB UART" provided in
the Cortex-M System Design Kit (CMSDK).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1500029487-14822-3-git-send-email-peter.maydell@linaro.org
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Parallel device don't register be->chr_can_read function, but remote
disconnect event is handled in chr_read.So connected parallel device
can not detect remote disconnect event. The chardevs with chr_can_read=NULL
has the same problem.
Signed-off-by: Peng Hao <peng.hao2@zte.com.cn>
Reviewed-by: Wang Yechao <wang.yechao255@zte.com.cn>
Reviewed-by: Jiang Biao <jiang.biao2@zte.com.cn>
Message-Id: <1499874119-67558-1-git-send-email-peng.hao2@zte.com.cn>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This allows to change the port's backend runtime, e.g. change it from
file to a socket making it possible to establish a debug session with
WinDbg
> qemu-system [..] -chardev file,id=charchannel2,path=/tmp/charchannel2 \
-device isa-serial,chardev=charchannel2,id=channel2
QEMU 2.9.50 monitor - type 'help' for more information
(qemu) chardev-change charchannel2 \
socket,host=127.0.0.1,port=4242,server,nowait
For a backend change, a number of ioctls has to be replayed to sync
the current setup of a frontend to a backend tty. This is hopefully
enough so we don't have to track, store and replay the whole original
control byte sequence.
Signed-off-by: Anton Nefedov <anton.nefedov@virtuozzo.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <1499342940-56739-14-git-send-email-anton.nefedov@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
will be used by the following patch
Signed-off-by: Anton Nefedov <anton.nefedov@virtuozzo.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1499342940-56739-13-git-send-email-anton.nefedov@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In case of a backend change, the handler functions and the watch have
to be reset.
Signed-off-by: Anton Nefedov <anton.nefedov@virtuozzo.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <1499342940-56739-12-git-send-email-anton.nefedov@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
frontends should avoid accessing CharDriver struct where possible
Signed-off-by: Anton Nefedov <anton.nefedov@virtuozzo.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1499342940-56739-6-git-send-email-anton.nefedov@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Frontends should have an interface to setup the handler of a backend change.
The interface will be used in the next commits
Signed-off-by: Anton Nefedov <anton.nefedov@virtuozzo.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1499342940-56739-3-git-send-email-anton.nefedov@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
iQIcBAABAgAGBQJZMbiwAAoJENro4Ql1lpzlEm0P/RViCB92pz62wdcsjpXvqwBO
ddhfQqPaGE+BD1tRcrOxDFKTWEnxFN4Oj9zNQ+/FgLcckZ5qAy6PkuCnesG2eJjG
c43y07e+u89G8L+7zLoAw+fYt8tnb5+ood6Q6WWH9rbNHLaIlMvwzomm3Rkf+1L/
PKVixcnFBxulTTftLgVUqpFSRrDDlywrmK9gjoDRHeIp7fZTxUib5T720ShszZe5
C2iym5Ucb5ohEoq4LfY+mPWVGkTdMtsX3Vz5eHsTqoYYY1akTg5CwgGQuqbS/kXN
7/4nkX6otkxTlU1+ydWEQCpD3orWEUJUeKUlLA48rAckqJyX3mfx94AeIOYseILM
vMdxQo549ofcann1RtHyPkgfwyl8rrFRZ2xdkYGeSJ2zyv6Ekcxs0r5NXX7DMZBY
oyjH38UTpHBhZp5l/0KAff0y0FNnDz6JJttgkcqHz8Qd4chE6JP9X9gx+9xkakst
ytbiFP5NuG9RTwWjFSXObgZl9QU/n+JuJ/kr/LMMTgmPYwONW3NglBGgAoRDu/gC
4YAmdSWf2UYlQg1IxTn2KT4U4Dn56DEmcaL9yDBH+UJLhWpxle9+D2MVruJN7MPS
H0/8ytXvmb99DMWOhIdRmOzWCmQ/YAg/CAXmUZPX7sul0b3TNhSDqEi2qnLR84GT
GSOh5aGbQ2H8DGQioGLV
=5eL6
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/elmarco/tags/chrfe-pull-request' into staging
# gpg: Signature made Fri 02 Jun 2017 20:12:48 BST
# gpg: using RSA key 0xDAE8E10975969CE5
# gpg: Good signature from "Marc-André Lureau <marcandre.lureau@redhat.com>"
# gpg: aka "Marc-André Lureau <marcandre.lureau@gmail.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 87A9 BD93 3F87 C606 D276 F62D DAE8 E109 7596 9CE5
* remotes/elmarco/tags/chrfe-pull-request:
char: move char devices to chardev/
char: make chr_fe_deinit() optionaly delete backend
char: rename functions that are not part of fe
char: move CharBackend handling in char-fe unit
char: generalize qemu_chr_write_all()
be-hci: use backend functions
chardev: serial & parallel declaration to own headers
chardev: move headers to include/chardev
Remove/replace sysemu/char.h inclusion
char-win: close file handle except with console
char-win: rename hcom->file
char-win: rename win_chr_init/poll win_chr_serial_init/poll
char-win: remove WinChardev.len
char-win: simplify win_chr_read()
char: cast ARRAY_SIZE() as signed to silent warning on empty array
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since commit d4c19cdeeb ("virtio-serial:
add missing virtio_detach_element() call") the following commands may
cause QEMU to segfault:
$ qemu -M accel=kvm -cpu host -m 1G \
-drive if=virtio,file=test.img,format=raw \
-device virtio-serial-pci,id=virtio-serial0 \
-chardev socket,id=channel1,path=/tmp/chardev.sock,server,nowait \
-device virtserialport,chardev=channel1,bus=virtio-serial0.0,id=port1
$ nc -U /tmp/chardev.sock
^C
(guest)$ cat /dev/zero >/dev/vport0p1
The segfault is non-deterministic: if the event loop notices the socket
has been closed then there is no crash. The disconnect has to happen
right before QEMU attempts to write data to the socket.
The backtrace is as follows:
Thread 1 "qemu-system-x86" received signal SIGSEGV, Segmentation fault.
0x00005555557e0698 in do_flush_queued_data (port=0x5555582cedf0, vq=0x7fffcc854290, vdev=0x55555807b1d0) at hw/char/virtio-serial-bus.c:180
180 for (i = port->iov_idx; i < port->elem->out_num; i++) {
#1 0x000055555580d363 in virtio_queue_notify_vq (vq=0x7fffcc854290) at hw/virtio/virtio.c:1524
#2 0x000055555580d363 in virtio_queue_host_notifier_read (n=0x7fffcc8542f8) at hw/virtio/virtio.c:2430
#3 0x0000555555b3482c in aio_dispatch_handlers (ctx=ctx@entry=0x5555566b8c80) at util/aio-posix.c:399
#4 0x0000555555b350d8 in aio_dispatch (ctx=0x5555566b8c80) at util/aio-posix.c:430
#5 0x0000555555b3212e in aio_ctx_dispatch (source=<optimized out>, callback=<optimized out>, user_data=<optimized out>) at util/async.c:261
#6 0x00007fffde71de52 in g_main_context_dispatch () at /lib64/libglib-2.0.so.0
#7 0x0000555555b34353 in glib_pollfds_poll () at util/main-loop.c:213
#8 0x0000555555b34353 in os_host_main_loop_wait (timeout=<optimized out>) at util/main-loop.c:261
#9 0x0000555555b34353 in main_loop_wait (nonblocking=<optimized out>) at util/main-loop.c:517
#10 0x0000555555773207 in main_loop () at vl.c:1917
#11 0x0000555555773207 in main (argc=<optimized out>, argv=<optimized out>, envp=<optimized out>) at vl.c:4751
The do_flush_queued_data() function does not anticipate chardev close
events during vsc->have_data(). It expects port->elem to remain
non-NULL for the duration its for loop.
The fix is simply to return from do_flush_queued_data() if the port
closes because the close event already frees port->elem and drains the
virtqueue - there is nothing left for do_flush_queued_data() to do.
Reported-by: Sitong Liu <siliu@redhat.com>
Reported-by: Min Deng <mdeng@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Virtio serial device controls the lifetime of virtio-serial-bus and
virtio-serial-bus links back to the device via its hotplug-handler
property. This extra ref-count prevents the device from getting
finalized, leaving the VirtIODevice memory listener registered and
leading to use-after-free later on.
This patch addresses the same issue as Fam Zheng's
"virtio-scsi: Unset hotplug handler when unrealize"
only for a different virtio device.
Cc: qemu-stable@nongnu.org
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
This simplifies removing a backend for a frontend user (no need to
retrieve the associated driver and separate delete call etc).
NB: many frontends have questionable handling of ending a chardev. They
should probably delete the backend to prevent broken reusage.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Move all the frontend struct and methods to a seperate unit. This avoids
accidentally mixing backend and frontend calls, and helps with readabilty.
Make qemu_chr_replay() a macro shared by both char and char-fe.
Export qemu_chr_write(), and use a macro for qemu_chr_write_all()
(nb: yes, CharBackend is for char frontend :)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
So they are all in one place. The following patch will move serial &
parallel declarations to the respective headers.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Those are apparently unnecessary includes.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Mark 3270 as non-migratable for the experimental stage. Enable
the 3270 device so that we can use x3270 client to operate the guest.
Run qemu with the arguments:
-chardev socket,id=char3270_0,host=0.0.0.0,port=23,nowait,server,tn3270 \
-device x-terminal3270,chardev=char3270_0,devno=fe.0.000a,id=terminal3270_0 \
There are some restrictions for the first stage: We don't support SSL
connections, multiple client connections and client resizing. Only
tested with the x3270 client.
Signed-off-by: Jing Liu <liujbjl@linux.vnet.ibm.com>
Signed-off-by: Yang Chen <bjcyang@linux.vnet.ibm.com>
Reviewed-by: QingFeng Hao <haoqf@linux.vnet.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
To ensure that we do not keep any 3270 sockets where the client is not
connected anymore, we send a packet with the timing mark option after
ten minutes of client inactivity. If the client does not answer it,
then the socket will be closed automatically.
This helps to ensure that there is no half-open situation on the 3270
socket.
Signed-off-by: Jing Liu <liujbjl@linux.vnet.ibm.com>
Reviewed-by: QingFeng Hao <haoqf@linux.vnet.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
This introduces a chr_event handler to handle the 3270 connection
and disconnection events.
Signed-off-by: Jing Liu <liujbjl@linux.vnet.ibm.com>
Reviewed-by: QingFeng Hao <haoqf@linux.vnet.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
This introduces the input and output handlers for 3270 device, setting
up the data tunnel among guest kernel, qemu and the 3270 client.
After the client connected and TN3270 handshake done, signal the not-ready
to ready status by an unsolicited device-end interrupt, and then the 3270
data stream could be handled correctly between the channel and socket.
Multiple commands generated by "Reset" key on x3270 are not supported now,
just simply terminate the connection.
Signed-off-by: Jing Liu <liujbjl@linux.vnet.ibm.com>
Signed-off-by: Yang Chen <bjcyang@linux.vnet.ibm.com>
Reviewed-by: QingFeng Hao <haoqf@linux.vnet.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
