This device is used by both ARM (BCM2836, for raspi2) and AArch64
(BCM2837, for raspi3) targets, and is not CPU-specific.
Move it to common object, so we build it once for all targets.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190427133028.12874-1-philmd@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In the v7M architecture, if an exception is generated in the process
of doing the lazy stacking of FP registers, the handling of
possible escalation to HardFault is treated differently to the normal
approach: it works based on the saved information about exception
readiness that was stored in the FPCCR when the stack frame was
created. Provide a new function armv7m_nvic_set_pending_lazyfp()
which pends exceptions during lazy stacking, and implements
this logic.
This corresponds to the pseudocode TakePreserveFPException().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190416125744.27770-22-peter.maydell@linaro.org
Implement the code which updates the FPCCR register on an
exception entry where we are going to use lazy FP stacking.
We have to defer to the NVIC to determine whether the
various exceptions are currently ready or not.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20190416125744.27770-12-peter.maydell@linaro.org
The M-profile floating point support has three associated config
registers: FPCAR, FPCCR and FPDSCR. It also makes the registers
CPACR and NSACR have behaviour other than reads-as-zero.
Add support for all of these as simple reads-as-written registers.
We will hook up actual functionality later.
The main complexity here is handling the FPCCR register, which
has a mix of banked and unbanked bits.
Note that we don't share storage with the A-profile
cpu->cp15.nsacr and cpu->cp15.cpacr_el1, though the behaviour
is quite similar, for two reasons:
* the M profile CPACR is banked between security states
* it preserves the invariant that M profile uses no state
inside the cp15 substruct
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190416125744.27770-4-peter.maydell@linaro.org
For M-profile the MVFR* ID registers are memory mapped, in the
range we implement via the NVIC. Allow them to be read.
(If the CPU has no FPU, these registers are defined to be RAZ.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190416125744.27770-3-peter.maydell@linaro.org
In the stripe8() function we use a variable length array; however
we know that the maximum length required is MAX_NUM_BUSSES. Use
a fixed-length array and an assert instead.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Message-id: 20190328152635.2794-1-peter.maydell@linaro.org
The SMMUNotifierNode struct is not necessary and brings extra
complexity so let's remove it. We now directly track the SMMUDevices
which have registered IOMMU MR notifiers.
This is inspired from the same transformation on intel-iommu
done in commit b4a4ba0d68
("intel-iommu: remove IntelIOMMUNotifierNode")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-id: 20190409160219.19026-1-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds support for a generic MMU-less Nios II board that can
be used e.g. for bare-metal compiler testing with the linker script
and startup code provided by libgloss. Nios II booting is also
tweaked so that bare-metal binaries start executing in RAM starting at
0x00000000, rather than an alias at 0xc0000000, which allows features
such as unwinding to work when binaries are linked to start at the
beginning of the address space.
The generic_nommu.c parts are based on code by Andrew Jenner, which was
in turn based on code by Marek Vasut.
Originally by Marek Vasut and Andrew Jenner.
Signed-off-by: Sandra Loosemore <sandra@codesourcery.com>
Signed-off-by: Julian Brown <julian@codesourcery.com>
Signed-off-by: Andrew Jenner <andrew@codesourcery.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1554321185-2825-2-git-send-email-sandra@codesourcery.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Here's the first ppc target pull request for qemu-4.1. This has a
number of things that have accumulated while qemu-4.0 was frozen.
* A number of emulated MMU improvements from Ben Herrenschmidt
* Assorted cleanups fro Greg Kurz
* A large set of mostly mechanical cleanups from me to make target/ppc
much closer to compliant with the modern coding style
* Support for passthrough of NVIDIA GPUs using NVLink2
As well as some other assorted fixes.
-----BEGIN PGP SIGNATURE-----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=RpAK
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.1-20190426' into staging
ppc patch queue 2019-04-26
Here's the first ppc target pull request for qemu-4.1. This has a
number of things that have accumulated while qemu-4.0 was frozen.
* A number of emulated MMU improvements from Ben Herrenschmidt
* Assorted cleanups fro Greg Kurz
* A large set of mostly mechanical cleanups from me to make target/ppc
much closer to compliant with the modern coding style
* Support for passthrough of NVIDIA GPUs using NVLink2
As well as some other assorted fixes.
# gpg: Signature made Fri 26 Apr 2019 07:02:19 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.1-20190426: (36 commits)
target/ppc: improve performance of large BAT invalidations
ppc/hash32: Rework R and C bit updates
ppc/hash64: Rework R and C bit updates
ppc/spapr: Use proper HPTE accessors for H_READ
target/ppc: Don't check UPRT in radix mode when in HV real mode
target/ppc/kvm: Convert DPRINTF to traces
target/ppc/trace-events: Fix trivial typo
spapr: Drop duplicate PCI swizzle code
spapr_pci: Get rid of duplicate code for node name creation
target/ppc: Style fixes for translate/spe-impl.inc.c
target/ppc: Style fixes for translate/vmx-impl.inc.c
target/ppc: Style fixes for translate/vsx-impl.inc.c
target/ppc: Style fixes for translate/fp-impl.inc.c
target/ppc: Style fixes for translate.c
target/ppc: Style fixes for translate_init.inc.c
target/ppc: Style fixes for monitor.c
target/ppc: Style fixes for mmu_helper.c
target/ppc: Style fixes for mmu-hash64.[ch]
target/ppc: Style fixes for mmu-hash32.[ch]
target/ppc: Style fixes for misc_helper.c
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With MT-TCG, we are now running translation in a racy way, thus
we need to mimic hardware when it comes to updating the R and
C bits, by doing byte stores.
The current "store_hpte" abstraction is ill suited for this, we
replace it with two separate callbacks for setting R and C.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190411080004.8690-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190411080004.8690-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
LSI mapping in spapr currently open-codes standard PCI swizzling. It thus
duplicates the code of pci_swizzle_map_irq_fn().
Expose the swizzling formula so that it can be used with a slot number
when building the device tree. Simply drop pci_spapr_map_irq() and call
pci_swizzle_map_irq_fn() instead.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155448184841.8446.13959787238854054119.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
According to the changelog of 298a971024, SpaprPhbState::dtbusname was
introduced to "make it easier to relate the guest and qemu views of memory
to each other", hence its name.
Use it when creating the PHB node to avoid code duplication.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155448184292.8446.8225650773162648595.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr_ics_create() is only called once. Merge it in spapr_irq_init_xics()
and simplify a bit the error handling by using 'error_fatal' .
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190321144914.19934-13-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Removing RTAS handlers will become necessary when the new pseries
machine supporting multiple interrupt mode is introduced.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190321144914.19934-9-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In commit 47973a2dbf we split the last generic chipset out of
the PC board, but missed to remove the i8042 keyboard controller.
This omission was later fixed in commit 7cb00357c1, but here we
forgot to remove the "i8042.h" include. Do it now.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190316201528.9140-1-philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
NVIDIA V100 GPUs have on-board RAM which is mapped into the host memory
space and accessible as normal RAM via an NVLink bus. The VFIO-PCI driver
implements special regions for such GPUs and emulates an NVLink bridge.
NVLink2-enabled POWER9 CPUs also provide address translation services
which includes an ATS shootdown (ATSD) register exported via the NVLink
bridge device.
This adds a quirk to VFIO to map the GPU memory and create an MR;
the new MR is stored in a PCI device as a QOM link. The sPAPR PCI uses
this to get the MR and map it to the system address space.
Another quirk does the same for ATSD.
This adds additional steps to sPAPR PHB setup:
1. Search for specific GPUs and NPUs, collect findings in
sPAPRPHBState::nvgpus, manage system address space mappings;
2. Add device-specific properties such as "ibm,npu", "ibm,gpu",
"memory-block", "link-speed" to advertise the NVLink2 function to
the guest;
3. Add "mmio-atsd" to vPHB to advertise the ATSD capability;
4. Add new memory blocks (with extra "linux,memory-usable" to prevent
the guest OS from accessing the new memory until it is onlined) and
npuphb# nodes representing an NPU unit for every vPHB as the GPU driver
uses it for link discovery.
This allocates space for GPU RAM and ATSD like we do for MMIOs by
adding 2 new parameters to the phb_placement() hook. Older machine types
set these to zero.
This puts new memory nodes in a separate NUMA node to as the GPU RAM
needs to be configured equally distant from any other node in the system.
Unlike the host setup which assigns numa ids from 255 downwards, this
adds new NUMA nodes after the user configures nodes or from 1 if none
were configured.
This adds requirement similar to EEH - one IOMMU group per vPHB.
The reason for this is that ATSD registers belong to a physical NPU
so they cannot invalidate translations on GPUs attached to another NPU.
It is guaranteed by the host platform as it does not mix NVLink bridges
or GPUs from different NPU in the same IOMMU group. If more than one
IOMMU group is detected on a vPHB, this disables ATSD support for that
vPHB and prints a warning.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[aw: for vfio portions]
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Message-Id: <20190312082103.130561-1-aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=tJvv
-----END PGP SIGNATURE-----
Merge tag 's390-ccw-bios-2019-04-12' into s390-next-staging
Support for booting from a vfio-ccw passthrough dasd device
# gpg: Signature made Fri 12 Apr 2019 01:17:03 PM CEST
# gpg: using RSA key 2ED9D774FE702DB5
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [undefined]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [undefined]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
* tag 's390-ccw-bios-2019-04-12':
pc-bios/s390: Update firmware images
s390-bios: Use control unit type to find bootable devices
s390-bios: Support booting from real dasd device
s390-bios: Add channel command codes/structs needed for dasd-ipl
s390-bios: Use control unit type to determine boot method
s390-bios: Refactor virtio to run channel programs via cio
s390-bios: Factor finding boot device out of virtio code path
s390-bios: Extend find_dev() for non-virtio devices
s390-bios: cio error handling
s390-bios: Support for running format-0/1 channel programs
s390-bios: ptr2u32 and u32toptr
s390-bios: Map low core memory
s390-bios: Decouple channel i/o logic from virtio
s390-bios: Clean up cio.h
s390-bios: decouple common boot logic from virtio
s390-bios: decouple cio setup from virtio
s390 vfio-ccw: Add bootindex property and IPLB data
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Rename qemu_getrampagesize() to qemu_minrampagesize(). While at it,
properly rename find_max_supported_pagesize() to
find_min_backend_pagesize().
s390x is actually interested into the maximum ram pagesize, so
introduce and use qemu_maxrampagesize().
Add a TODO, indicating that looking at any mapped memory backends is not
100% correct in some cases.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20190417113143.5551-3-david@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Right now we configure the pagesize quite early, when initializing KVM.
This is long before system memory is actually allocated via
memory_region_allocate_system_memory(), and therefore memory backends
marked as mapped.
Instead, let's configure the maximum page size after initializing
memory in s390_memory_init(). cap_hpage_1m is still properly
configured before creating any CPUs, and therefore before configuring
the CPU model and eventually enabling CMMA.
This is not a fix but rather a preparation for the future, when initial
memory might reside on memory backends (not the case for s390x right now)
We will replace qemu_getrampagesize() soon by a function that will always
return the maximum page size (not the minimum page size, which only
works by pure luck so far, as there are no memory backends).
Acked-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20190417113143.5551-2-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190417190641.26814-8-armbru@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190417190641.26814-7-armbru@redhat.com>
Cc: Paul Burton <pburton@wavecomp.com>
Cc: Aleksandar Rikalo <arikalo@wavecomp.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190417190641.26814-5-armbru@redhat.com>
load_fit() reports errors with error_printf() instead of
error_report(). Worse, it even reports errors it actually recovers
from, in fit_cfg_compatible() and fit_load_fdt(). Messed up in
initial commit 51b58561c1.
Convert the helper functions for load_fit() to Error. Make sure each
failure path sets an error.
Fix fit_cfg_compatible() and fit_load_fdt() not to report errors they
actually recover from.
Convert load_fit() to error_report().
Cc: Paul Burton <pburton@wavecomp.com>
Cc: Aleksandar Rikalo <arikalo@wavecomp.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190417190641.26814-4-armbru@redhat.com>
The ObjectInfo struct has a variable length array containing the UTF-16
encoded filename. The number of characters of trailing data is given by
the 'length' field in the struct and this must be validated against the
size of the data packet received from the guest.
Since the data is UTF-16, we must convert the byte count we have to a
character count before validating. This must take care to truncate if
a malicious guest sent an odd number of bytes.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add bootindex property and iplb data for vfio-ccw devices. This allows us to
forward boot information into the bios for vfio-ccw devices.
Refactor s390_get_ccw_device() to return device type. This prevents us from
having to use messy casting logic in several places.
Signed-off-by: Jason J. Herne <jjherne@linux.ibm.com>
Acked-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1554388475-18329-2-git-send-email-jjherne@linux.ibm.com>
[thuth: fixed "typedef struct VFIOCCWDevice" build failure with clang]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Recent commit 5cf0d326a0 fixed a regression which was preventing the
guest to access the extended config space of a PCIe device. This was
done by introducing a new PCI bus subtype for PAPR. The original fix
was causing PCI busses to be named "spapr-pci-host-bridge-root-bus.N"
instead of "pci.N", which was making upper layers unhappy of course.
This got worked around by hardcoding the PCI bus name to "pci.0", but
this only works for the default PHB. And we're now hitting:
# qemu-system-ppc64 \
-device spapr-pci-host-bridge,index=1 \
-device e1000e,bus=pci.0 \
-device e1000e,bus=pci.1
qemu-system-ppc64: -device e1000e,bus=pci.1: Bus 'pci.1' not found
David already posted some patches [1] to control PCI extended config
space accesses with a new flag in the base PCI bus class instead of
subtyping. These patches are a bit more intrusive though, and
are targetted for 4.1.
When no name is passed to pci_register_bus(), the core device code
generates a lowercase name based on the QOM typename. The typename
for the base PCI bus class is "PCI", hence the "pci.0", "pci.1"
bus names. Rename the type of the PAPR PCI bus to "pci", so that
the QOM code can generate proper names. This is a hack but it is
enough to fix the regression. And all this will be reworked properly
in 4.1.
[1] https://patchwork.ozlabs.org/project/qemu-devel/list/?series=100486
Fixes: 5cf0d326a0
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155500034416.646888.1307366522340665522.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
QEMU currently crashes when you try to hot-plug an "nvdimm" device
on older machine types:
$ qemu-system-x86_64 -monitor stdio -M pc-1.1
QEMU 3.1.92 monitor - type 'help' for more information
(qemu) device_add nvdimm,id=nvdimmn1
qemu-system-x86_64: /home/thuth/devel/qemu/util/error.c:57: error_setv:
Assertion `*errp == ((void *)0)' failed.
Aborted (core dumped)
The call to hotplug_handler_pre_plug() in pc_memory_pre_plug() has been
added recently before the check whether nvdimm is enabled. It should
be done after the check. And while we're at it, also check the errp
after the hotplug_handler_pre_plug(), otherwise errors are silently
ignored here.
Fixes: 9040e6dfa8
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190407092314.11066-1-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The PAPR PHB acts as a legacy PCI bus but it allows PCIe extended
config space accesses anyway (for pseries-2.9 and newer machine
types).
Introduce a specific PCI bus subtype to inform the common PCI code
about that.
Fixes: c2077e2ca0
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155414130834.574858.16502276132110219890.stgit@bahia.lan>
[dwg: Apply fix so we don't rename the default pci bus, breaking everything]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Some PHB implementations, eg. PAPR used on pseries machine, act like
a regular PCI bus rather than a PCIe bus, but allow access to the
PCIe extended config space anyway.
Introduce a new PCI bus class method to modelize this behaviour and
use it when adjusting the config space size limit during accesses.
No behaviour change for existing PCI bus types.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155414130271.574858.4253514266378127489.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This patch set contains a pair of tightly coupled PLIC bug fixes:
* We were calculating the PLIC addresses incorrectly.
* We were installing the wrong number of PLIC interrupts.
The two bugs togther resulted in a mostly-working system, but they're
impossible to seperate because fixing one bug would result in
significant breakage. As a result they're in the same patch.
There is also a cleanup to use qemu_log_mask(LOG_GUEST_ERROR,...) for
error reporting.
As far as I know these are the last outstanding RISC-V patches for 4.0.
v2 no longer fails "make check" for me... sorry!
-----BEGIN PGP SIGNATURE-----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=APjM
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/palmer/tags/riscv-for-master-4.0-rc3-v2' into staging
RISC-V Patches for 4.0-rc3, v2
This patch set contains a pair of tightly coupled PLIC bug fixes:
* We were calculating the PLIC addresses incorrectly.
* We were installing the wrong number of PLIC interrupts.
The two bugs togther resulted in a mostly-working system, but they're
impossible to seperate because fixing one bug would result in
significant breakage. As a result they're in the same patch.
There is also a cleanup to use qemu_log_mask(LOG_GUEST_ERROR,...) for
error reporting.
As far as I know these are the last outstanding RISC-V patches for 4.0.
v2 no longer fails "make check" for me... sorry!
# gpg: Signature made Fri 05 Apr 2019 01:33:57 BST
# gpg: using RSA key 00CE76D1834960DFCE886DF8EF4CA1502CCBAB41
# gpg: issuer "palmer@dabbelt.com"
# gpg: Good signature from "Palmer Dabbelt <palmer@dabbelt.com>" [unknown]
# gpg: aka "Palmer Dabbelt <palmer@sifive.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 00CE 76D1 8349 60DF CE88 6DF8 EF4C A150 2CCB AB41
* remotes/palmer/tags/riscv-for-master-4.0-rc3-v2:
riscv: plic: Log guest errors
riscv: plic: Fix incorrect irq calculation
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Instead of using error_report() to print guest errors let's use
qemu_log_mask(LOG_GUEST_ERROR,...) to log the error.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This patch fixes four different things, to maintain bisectability they
have been merged into a single patch. The following fixes are below:
sifive_plic: Fix incorrect irq calculation
The irq is incorrectly calculated to be off by one. It has worked in the
past as the priority_base offset has also been set incorrectly. We are
about to fix the priority_base offset so first first the irq
calculation.
sifive_u: Fix PLIC priority base offset and numbering
According to the FU540 manual the PLIC source priority address starts at
an offset of 0x04 and not 0x00. The same manual also specifies that the
PLIC only has 53 source priorities. Fix these two incorrect header
files.
We also need to over extend the plic_gpios[] array as the PLIC sources
count from 1 and not 0.
riscv: sifive_e: Fix PLIC priority base offset
According to the FE31 manual the PLIC source priority address starts at
an offset of 0x04 and not 0x00.
riscv: virt: Fix PLIC priority base offset
Update the virt offsets based on the newly updated SiFive U and SiFive E
offsets.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The Xen blkif protocol requires that sector based quantities should be
interpreted strictly as multiples of 512 bytes. Specifically:
"first_sect and last_sect in blkif_request_segment, as well as
sector_number in blkif_request, are always expressed in 512-byte units."
Commit fcab2b464e "xen: add header and build dataplane/xen-block.c"
incorrectly modified behaviour to use the block device logical_block_size
property as the scale, instead of correctly shifting values by the
hardcoded BDRV_SECTOR_BITS (and hence scaling them to 512 byte units).
This patch undoes that change and restores compliance with the spec.
Furthermore, this patch also restores the original xen_disk behaviour
of advertizing a hardcoded 'sector-size' value of 512 in xenstore and
scaling 'sectors' accordingly. The realize() method is also modified to
fail if logical_block_size is set to anything other than 512.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20190401121719.27208-1-paul.durrant@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
...and properly enable it when synthesizing a drive.
The Xen toolstack sets 'discard-enable' to '1' in xenstore when it wants
to enable discard on a specified image. The code in
xen_block_drive_create() correctly parses this and uses it to set
'discard' to 'unmap' for the file_layer, but fails to do the same for the
driver_layer (which effectively disables it). Meanwhile the code in
xen_block_realize() advertizes discard support to the frontend in the
default case (because conf->discard_granularity defaults to -1), even when
the underlying image may not handle it.
This patch adds the missing option to the driver_layer in
xen_block_driver_create() and checks whether BDRV_O_UNMAP is actually
set on the block device before advertizing discard to the frontend.
In the case that discard is supported it also makes sure that the
granularity is set to the physical block size.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20190320142825.24565-1-paul.durrant@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Compiling with GCC 9 complains
hw/s390x/3270-ccw.c: In function ‘emulated_ccw_3270_cb’:
hw/s390x/3270-ccw.c:81:19: error: taking address of packed member of ‘struct SCHIB’ may result in an unaligned pointer value [-Werror=address-of-packed-member]
81 | SCSW *s = &sch->curr_status.scsw;
| ^~~~~~~~~~~~~~~~~~~~~~
This local variable is only present to save a little bit of
typing when setting the field later. Get rid of this to avoid
the warning about unaligned accesses.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20190329111104.17223-15-berrange@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Compiling with GCC 9 complains
hw/s390x/ipl.c: In function ‘s390_ipl_set_boot_menu’:
hw/s390x/ipl.c:256:25: warning: taking address of packed member of ‘struct QemuIplParameters’ may result in an unaligned pointer value [-Waddress-of-packed-member]
256 | uint32_t *timeout = &ipl->qipl.boot_menu_timeout;
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~
This local variable is only present to save a little bit of
typing when setting the field later. Get rid of this to avoid
the warning about unaligned accesses.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20190329111104.17223-14-berrange@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Farhan Ali <alifm@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The GCC 9 compiler complains about many places in s390 code
that take the address of members of the 'struct SCHIB' which
is marked packed:
hw/s390x/css.c: In function ‘sch_handle_clear_func’:
hw/s390x/css.c:698:15: warning: taking address of packed member of ‘struct SCHIB’ may result in an unaligned pointer val\
ue [-Waddress-of-packed-member]
698 | PMCW *p = &sch->curr_status.pmcw;
| ^~~~~~~~~~~~~~~~~~~~~~
hw/s390x/css.c:699:15: warning: taking address of packed member of ‘struct SCHIB’ may result in an unaligned pointer val\
ue [-Waddress-of-packed-member]
699 | SCSW *s = &sch->curr_status.scsw;
| ^~~~~~~~~~~~~~~~~~~~~~
...snip many more...
Almost all of these are just done for convenience to avoid
typing out long variable/field names when referencing struct
members. We can get most of this convenience by taking the
address of the 'struct SCHIB' instead, avoiding triggering
the compiler warnings.
In a couple of places we copy via a local variable which is
a technique already applied elsewhere in s390 code for this
problem.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20190329111104.17223-13-berrange@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The GCC 9 compiler complains about many places in s390 code
that take the address of members of the 'struct SCHIB' which
is marked packed:
hw/vfio/ccw.c: In function ‘vfio_ccw_io_notifier_handler’:
hw/vfio/ccw.c:133:15: warning: taking address of packed member of ‘struct SCHIB’ may result in an unaligned pointer value \
[-Waddress-of-packed-member]
133 | SCSW *s = &sch->curr_status.scsw;
| ^~~~~~~~~~~~~~~~~~~~~~
hw/vfio/ccw.c:134:15: warning: taking address of packed member of ‘struct SCHIB’ may result in an unaligned pointer value \
[-Waddress-of-packed-member]
134 | PMCW *p = &sch->curr_status.pmcw;
| ^~~~~~~~~~~~~~~~~~~~~~
...snip many more...
Almost all of these are just done for convenience to avoid
typing out long variable/field names when referencing struct
members. We can get most of this convenience by taking the
address of the 'struct SCHIB' instead, avoiding triggering
the compiler warnings.
In a couple of places we copy via a local variable which is
a technique already applied elsewhere in s390 code for this
problem.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20190329111104.17223-12-berrange@redhat.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Farhan Ali <alifm@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
VTD_RTADDR_RTT is dropped even by the VT-d spec, so QEMU should
probably do the same thing (after all we never really implemented it).
Since we've had a field for that in the migration stream, to keep
compatibility we need to fill the hole up.
Please refer to VT-d spec 10.4.6.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20190329061422.7926-3-peterx@redhat.com>
Reviewed-by: Liu, Yi L <yi.l.liu@intel.com>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When introducing the initial support for scalable mode we added a
new field into vmstate however we blindly migrate that field without
notice. That'll break migration no matter forward or backward.
The normal way should be that we use something like
VMSTATE_UINT32_TEST() or subsections for the new vmstate field however
for this case of vt-d we can even make it simpler because we've
already migrated all the registers and it'll be fairly simple that we
re-generate root_scalable field from the register values during post
load of the device.
Fixes: fb43cf739e ("intel_iommu: scalable mode emulation")
Reviewed-by: Yi Sun <yi.y.sun@linux.intel.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20190329061422.7926-2-peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Message-Id: <20190321161832.10533-1-yuval.shaia@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
