* kraxel/usb.67:
uhci: Raise interrupt when requested even for non active tds
usb-redir: Don't make migration fail in none seamless case
usb-redir: Change usbredir_open_chardev into usbredir_create_parser
* mdroth/qga-pull-10-9-12:
qemu-ga: ga_open_pidfile(): add new line to pidfile
qemu-ga: use state dir from CONFIG_QEMU_LOCALSTATEDIR
configure: add --localstatedir
* stefanha/net:
net: consolidate NetClientState header files into one
virtio-net: update nc.link_down in virtio_net_load()
e1000: update nc.link_down in e1000_post_load()
rtl8139: implement 8139cp link status
* spice/spice.v61:
qxl: set default revision to 4
spice: raise requirement to 0.12
hw/qxl: qxl_dirty_surfaces: use uintptr_t
hw/qxl: fix condition for exiting guest_bug
hw/qxl: exit on failure to register qxl interface
qxl: fix range check for rev3 io commands.
qxl/update_area_io: cleanup invalid parameters handling
qxl: always update displaysurface on resize
According to the spec we must raise an interrupt when one is requested
even for non active tds.
Linux depends on this, for bulk transfers it runs an inactivity timer
to work around a bug in early uhci revisions, when we take longer then
200 ms to process a packet, this timer goes of, and as part of the
handling Linux then unlinks the qh, and relinks it after the frindex
has increased by atleast 1, the problem is Linux only checks for the
frindex increases on an interrupt, and we don't send that, causing
the qh to go inactive for more then 32 frames, at which point we
consider the packet cancelled.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Instead simple disconnect the device like host redirection does on
migration.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Added helper function to automatically connect SPI slaves based on the QOM child
nodes of a device. A SSI master device can call this routine to automatically
hook-up all child nodes to its SPI bus.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Added maintainership for SSI, M25P80 and the Xilinx SPI controllers.
Signed-off-by: Peter A. G. Crosthwaite <peter.crosthwaite@petalogix.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Added the two SPI controllers to the zynq machine model. Attached two SPI flash
devices to each controller.
Signed-off-by: Peter A. G. Crosthwaite <peter.crosthwaite@petalogix.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Added device model for the Xilinx Zynq SPI controller (SPIPS).
Signed-off-by: Peter A. G. Crosthwaite <peter.crosthwaite@petalogix.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Added SPI controller to the reference design, with two n25q128 spi-flashes
connected.
Signed-off-by: Peter A. G. Crosthwaite <peter.crosthwaite@petalogix.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Removed the explicit SSI mux and wired the CS line directly up to the SSI
devices.
Signed-off-by: Peter A. G. Crosthwaite <peter.crosthwaite@petalogix.com>
Allow multiple qdev_init_gpio_in() calls for the one device. The first call will
define GPIOs 0-N-1, the next GPIOs N- ... . Allows different GPIOs to be handled
with different handlers. Needed when two levels of the QOM class heirachy both
define GPIO functionality, as a single GPIO handler with an index selecter is
not possible.
Signed-off-by: Peter A. G. Crosthwaite <peter.crosthwaite@petalogix.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Slave creation function that can be used to create an SSI slave without
qdev_init() being called. This give machine models a chance to set properties.
Signed-off-by: Peter A. G. Crosthwaite <peter.crosthwaite@petalogix.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Added default CS behaviour for SSI slaves. SSI devices can set a property
to enable CS behaviour which will create a GPIO on the device which is the
CS. Tristating of the bus on SSI transfers is implemented.
Signed-off-by: Peter A. G. Crosthwaite <peter.crosthwaite@petalogix.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Removed assertion that only one device is attached to the SSI bus.
When multiple devices are attached, all slaves have their transfer function
called for transfers. Each device is responsible for knowing whether or not its
CS is active, and if not returning 0. The returned data is the logical or of
all responses from the (mulitple) devices.
Signed-off-by: Peter A. G. Crosthwaite <peter.crosthwaite@petalogix.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
FHS requires that pid files should end with a new line. Also change to
snprintf() while there.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Has the side effect of changing the default directory used to
save the freeze status file from /tmp to ${prefix}/var/run.
This is a beneficial change for two reasons:
1. FHS states that programs must not assume that files in /tmp will
still exist between invocations of the program. This defeats
the purpose of the freeze status file
2. FHS dictates that /var/run must be cleaned on boot, this
ensures that a stale freeze status file will be removed on boot
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Next commit wants to use it.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
DO_UPCAST is supposed to translate from the first member of a struct to
that struct, not from arbitrary ones. And it (usually) breaks the build
when neglecting this rule. Use container_of to fix the build breakage
and likely also the runtime behavior.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
aw: runtime behavior is actually the same, but clearly misuse of DO_UPCAST
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Blue Swirl reports that Clang doesn't like the structure we define to
avoid dynamic allocation for a number of calls to VFIO_DEVICE_SET_IRQS.
Adding an element after a variable sized type is a GNU extension.
Switch back to dynamic allocation, which really isn't a problem since
this is only done on interrupt setup changes.
Cc: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Take what we've learned from pci-assign and apply it to vfio-pci.
On reset, disable previous interrupt config, perform a device
reset if available, re-enable INTx, and disable memory regions on
the device to prevent continuing DMA.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This was a misinterpretation of the spec, hardware doesn't get to
specify how many were actually enabled through this field.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
We try to do lazy initialization of MSIX since we don't actually need
to setup anything until MSIX vectors start getting used. This leads
to problems if MSIX is enabled, but never used (we can end up trying
to re-enable INTx while it's still enabled). We also run into
problems trying to expand our reset function to tear down interrupts
as we can then get vector release notifications after we've released
data structures. By making explicit initialization and teardown we
can avoid both of these problems and behave more similar to bare
metal.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Occasionally we get regions added that overlap with existing mappings.
These always seems to be in the VGA ROM range. VFIO returns EBUSY
for these mapping attempts. We can try a little harder and assume
that the latest mapping is correct by removing any overlapping ranges
and retrying the original request.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
We can't afford the overhead of switching out and back into mmap mode
around each interrupt, but we can do it lazily via a timer. On INTx
interrupt, disable the mmap'd memory regions and set a timer. On
every interrupt, push the timer out. If the timer expires and the
interrupt is no longer pending, switch back to mmap mode.
This has the benefit that things like graphics cards, which rarely or
never, fire an interrupt don't need manual user intervention to add
the x-intx=off parameter. They'll just remain in mmap mode until they
trigger an interrupt, and if they don't continue to regularly fire
interrupts, they'll switch back.
The default timeout is tuned for network cards so that a ping is just
enough to keep them in non-mmap mode, where they have much better
latency. It is tunable with an experimental option,
x-intx-mmap-timeout-ms. A value of 0 keeps the device in non-mmap
mode after the first interrupt.
It's possible we could look at the class code of devices and come up
with reasonable per-class defaults based on expected interrupt
frequency and latency. None of this is used for MSI interrupts and
also won't be used if we can bypass through KVM.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This patch doesn't seem much useful alone, I must admit. However,
it makes sense as part of the upcoming directory reorganization,
where I want to have include/net/tap.h as the net<->hw interface
for tap. Then having both net/tap.h and include/net/tap.h does
not work. "Fixed" by moving all the init functions to a single
header file net/clients.h.
The patch also adopts a uniform style for including net/*.h files
from net/*.c, without the net/ path.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
nc.link_down could not be migrated, this patch updates link_down in
virtio_post_load() to keep it coincident with real link status.
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
This patch introduced e1000_post_load(), it will be called in the end of
migration. nc.link_down could not be migrated, this patch updates
link_down in e1000_post_load() to keep it coincident with real link
status.
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Add a link status chang callback and change the link status bit in BMSR
& MSR accordingly. Tested in Linux/Windows guests.
The link status bit of MediaStatus is infered from BasicModeStatus,
they are inverse.
nc.link_down could not be migrated, this patch updates link_down in
rtl8139_post_load() to keep it coincident with real link status.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
With the next qemu version (1.3) we are going to bump the qxl device
revision to 4. The new features available require a recent spice-server
version, so raise up the bar. Otherwise we would end up with different
qxl revisions depending on the spice-server version installed, which
would be a major PITA when it comes to compat properties.
Clear out a big bunch of #ifdefs which are not needed any more.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
As suggested by Paolo Bonzini, to avoid possible integer overflow issues.
Signed-off-by: Alon Levy <alevy@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This prevents a segfault later on when the device reset handler
tries to access a NULL ssd.worker since interface_attach_worker has
not been called.
Signed-off-by: Alon Levy <alevy@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Enables QXL_IO_FLUSH_SURFACES_ASYNC and QXL_IO_FLUSH_RELEASE
which are part of the qxl rev3 feature set.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This cleans up two additions of almost the same code in commits
511b13e2c9 and ccc2960d65. While at it, make error paths
consistent (always use 'break' instead of 'return').
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Cc: Dunrong Huang <riegamaths@gmail.com>
Cc: Alon Levy <alevy@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Don't try to be clever and skip displaysurface reinitialization in case
the size hasn't changed. Other parameters might have changed
nevertheless, for example depth or stride, resulting in rendering being
broken then.
Trigger: boot linux guest with vesafb, start X11, make sure both vesafb
and X11 use the display same resolution. Then watch X11 screen being
upside down.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
