Add a new dino_pcihost_unrealize() function to remove the address space when the
device is unrealized.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Helge Deller <deller@gmx.de>
Message-Id: <20220504092600.10048-8-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Almost all PA-RISC machines have either a button that is labeled with 'TOC' or
a BMC/GSP function to trigger a TOC. TOC is a non-maskable interrupt that is
sent to the processor. This can be used for diagnostic purposes like obtaining
a stack trace/register dump or to enter KDB/KGDB in Linux.
This patch adds support for such an emulated TOC button.
It wires up the qemu monitor "nmi" command to trigger a TOC. For that it
provides the hppa_nmi function which is assigned to the nmi_monitor_handler
function pointer. When called it raises the EXCP_TOC hardware interrupt in the
hppa_cpu_do_interrupt() function. The interrupt function then calls the
architecturally defined TOC function in SeaBIOS-hppa firmware (at fixed address
0xf0000000).
According to the PA-RISC PDC specification, the SeaBIOS firmware then writes
the CPU registers into PIM (processor internal memmory) for later analysis. In
order to write all registers it needs to know the contents of the CPU "shadow
registers" and the IASQ- and IAOQ-back values. The IAOQ/IASQ values are
provided by qemu in shadow registers when entering the SeaBIOS TOC function.
This patch adds a new aritificial opcode "getshadowregs" (0xfffdead2) which
restores the original values of the shadow registers. With this opcode SeaBIOS
can store those registers as well into PIM before calling an OS-provided TOC
handler.
To trigger a TOC, switch to the qemu monitor with Ctrl-A C, and type in the
command "nmi". After the TOC started the OS-debugger, exit the qemu monitor
with Ctrl-A C.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
This brings the hppa_hardware.h file in sync with the copy in the
SeaBIOS-hppa sources.
In order to support up to 16 CPUs, it's required to move the HPA for
MEMORY_HPA out of the address space of the new 16th CPU.
The new address of 0xfffff000 worked well for Linux and HP-UX, while
other addresses close to the former 0xfffbf000 area are used by the
architecture for local and global broadcasts.
The PIM_STORAGE_SIZE constant is used in SeaBIOS sources and
is relevant for the TOC/NMI feature.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Commit e50caf4a5c ("tracing: convert documentation to rST")
converted docs/devel/tracing.txt to docs/devel/tracing.rst.
We still have several references to the old file, so let's fix them
with the following command:
sed -i s/tracing.txt/tracing.rst/ $(git grep -l docs/devel/tracing.txt)
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210517151702.109066-2-sgarzare@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Stop including exec/address-spaces.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-5-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Stop including cpu.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-4-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Stop including hw/boards.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-3-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The include/hw/hw.h header only has a prototype for hw_error(),
so it does not make sense to include this in files that do not
use this function.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210326151848.2217216-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
We already have a generic PCI_SLOT() macro in "hw/pci/pci.h"
to extract the PCI slot identifier, use it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Paul Durrant <paul@xen.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20201012124506.3406909-5-philmd@redhat.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201026143028.3034018-5-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Emulate a power button switch, tell SeaBIOS the address via fw_cfg and
bind the power button to the qemu UI.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Change QEMU_FW_CFG_IO_BASE to shorter variant FW_CFG_IO_BASE and hand
over the actual port address in %r19 to SeaBIOS.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Devices on hppa occupy at least 4k starting at the HPA, so MEMORY_HPA+4k is
blocked (by Linux) for the memory module. I noticed this when testing the new
Linux kernel patch to let the fw_cfg entries show up in Linux under /proc.
The Linux kernel driver could not allocate the region for fw_cfg.
This new base address seems to not conflict.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Until now the TLB size was fixed at 256 entries. To allow operating
systems to utilize more TLB entries in the future, we need to tell
firmware how many TLB entries we actually support in the emulation.
Firmware then reports this to the operating system via the
PDC_CACHE_INFO call.
This patch simply does the preparation to allow more TLB entries.
Signed-off-by: Helge Deller <deller@gmx.de>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCX0bPowAKCRD3ErUQojoP
X43sAPwP4Prb0NQTw68l5oSwOoIcuWb4GZBjxOPecDis/0K2ogD/WswDJ8qk3RAQ
7XYGY8LuMdhwfcsx15TsuB/HAUie3QM=
=wIGS
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/hdeller/tags/target-hppa-v3-pull-request' into staging
artist out of bounds fixes
# gpg: Signature made Wed 26 Aug 2020 22:09:55 BST
# gpg: using EDDSA key BCE9123E1AD29F07C049BBDEF712B510A23A0F5F
# gpg: Good signature from "Helge Deller <deller@gmx.de>" [unknown]
# gpg: aka "Helge Deller <deller@kernel.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 4544 8228 2CD9 10DB EF3D 25F8 3E5F 3D04 A7A2 4603
# Subkey fingerprint: BCE9 123E 1AD2 9F07 C049 BBDE F712 B510 A23A 0F5F
* remotes/hdeller/tags/target-hppa-v3-pull-request:
hw/display/artist: Fix invalidation of lines near screen border
hw/display/artist: Fix invalidation of lines in artist_draw_line()
hw/display/artist: Unbreak size mismatch memory accesses
hw/display/artist: Prevent out of VRAM buffer accesses
Revert "hw/display/artist: Avoid drawing line when nothing to display"
hw/display/artist: Refactor artist_rop8() to avoid buffer over-run
hw/display/artist: Check offset in draw_line to avoid buffer over-run
hw/hppa/lasi: Don't abort on invalid IMR value
hw/display/artist.c: fix out of bounds check
hw/hppa: Implement proper SeaBIOS version check
seabios-hppa: Update to SeaBIOS hppa version 1
hw/hppa: Sync hppa_hardware.h file with SeaBIOS sources
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
NetBSD initializes the LASI IMR value with 0xffffffff to disable all LASI
interrupts. This triggered an assert() and stopped the emulation. By replacing
the check with a warning in the guest log we now allow NetBSD to boot again.
Signed-off-by: Helge Deller <deller@gmx.de>
Each architecture's sourceset is placed in an hw_arch dictionary, and picked up
from there when building the per-emulator static_library.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Meson doesn't enjoy the same flexibility we have with Make in choosing
the include path. In particular the tracing headers are using
$(build_root)/$(<D).
In order to keep the include directives unchanged,
the simplest solution is to generate headers with patterns like
"trace/trace-audio.h" and place forwarding headers in the source tree
such that for example "audio/trace.h" includes "trace/trace-audio.h".
This patch is too ugly to be applied to the Makefiles now. It's only
a way to separate the changes to the tracing header files from the
Meson rewrite of the tracing logic.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It's important that the SeaBIOS hppa firmware is at least at a minimal
level to ensure proper interaction between qemu and firmware.
Implement a proper firmware version check by telling SeaBIOS via the
fw_cfg interface which minimal SeaBIOS version is required by this
running qemu instance. If the firmware detects that it's too old, it
will stop.
Signed-off-by: Helge Deller <deller@gmx.de>
The hppa_hardware.h file is shared with SeaBIOS. Sync it.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Helge Deller <deller@gmx.de>
This is the transformation explained in the commit before previous.
Takes care of just one pattern that needs conversion. More to come in
this series.
Coccinelle script:
@ depends on !(file in "hw/arm/highbank.c")@
expression bus, type_name, dev, expr;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr;
identifier DOWN;
@@
- dev = DOWN(qdev_create(bus, type_name));
+ dev = DOWN(qdev_new(type_name));
... when != dev = expr
- qdev_init_nofail(DEVICE(dev));
+ qdev_realize_and_unref(DEVICE(dev), bus, &error_fatal);
@@
expression bus, type_name, expr;
identifier dev;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr, errp;
symbol true;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
@@
expression bus, type_name, expr, errp;
identifier dev;
symbol true;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
The first rule exempts hw/arm/highbank.c, because it matches along two
control flow paths there, with different @type_name. Covered by the
next commit's manual conversions.
Missing #include "qapi/error.h" added manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-10-armbru@redhat.com>
[Conflicts in hw/misc/empty_slot.c and hw/sparc/leon3.c resolved]
IEC binary prefixes ease code review: the unit is explicit.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200601142930.29408-7-f4bug@amsat.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
After previous clean ups we can drop direct inclusion of hw/ide.h from
several places.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: a3f72b663e537701c63cec5fc9cb8ed4f4249f28.1584457537.git.balaton@eik.bme.hu
Signed-off-by: John Snow <jsnow@redhat.com>
hw/hppa/machine.c uses NICInfo variables which are declared in
"net/net.h". Include it.
This fixes (when modifying unrelated headers):
hw/hppa/machine.c:126:21: error: use of undeclared identifier 'nb_nics'
for (i = 0; i < nb_nics; i++) {
^
hw/hppa/machine.c:127:30: error: use of undeclared identifier 'nd_table'
pci_nic_init_nofail(&nd_table[i], pci_bus, "e1000", NULL);
^
Acked-by: John Snow <jsnow@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200228114649.12818-10-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
There's no good reason for it to be type int, change it to bool.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200207161948.15972-3-philmd@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This series removes ad hoc RAM allocation API (memory_region_allocate_system_memory)
and consolidates it around hostmem backend. It allows to
* resolve conflicts between global -mem-prealloc and hostmem's "policy" option,
fixing premature allocation before binding policy is applied
* simplify complicated memory allocation routines which had to deal with 2 ways
to allocate RAM.
* reuse hostmem backends of a choice for main RAM without adding extra CLI
options to duplicate hostmem features. A recent case was -mem-shared, to
enable vhost-user on targets that don't support hostmem backends [1] (ex: s390)
* move RAM allocation from individual boards into generic machine code and
provide them with prepared MemoryRegion.
* clean up deprecated NUMA features which were tied to the old API (see patches)
- "numa: remove deprecated -mem-path fallback to anonymous RAM"
- (POSTPONED, waiting on libvirt side) "forbid '-numa node,mem' for 5.0 and newer machine types"
- (POSTPONED) "numa: remove deprecated implicit RAM distribution between nodes"
Introduce a new machine.memory-backend property and wrapper code that aliases
global -mem-path and -mem-alloc into automatically created hostmem backend
properties (provided memory-backend was not set explicitly given by user).
A bulk of trivial patches then follow to incrementally convert individual
boards to using machine.memory-backend provided MemoryRegion.
Board conversion typically involves:
* providing MachineClass::default_ram_size and MachineClass::default_ram_id
so generic code could create default backend if user didn't explicitly provide
memory-backend or -m options
* dropping memory_region_allocate_system_memory() call
* using convenience MachineState::ram MemoryRegion, which points to MemoryRegion
allocated by ram-memdev
On top of that for some boards:
* missing ram_size checks are added (typically it were boards with fixed ram size)
* ram_size fixups are replaced by checks and hard errors, forcing user to
provide correct "-m" values instead of ignoring it and continuing running.
After all boards are converted, the old API is removed and memory allocation
routines are cleaned up.
memory_region_allocate_system_memory() API is going away, so
replace it with memdev allocated MemoryRegion. The later is
initialized by generic code, so board only needs to opt in
to memdev scheme by providing
MachineClass::default_ram_id
and using MachineState::ram instead of manually initializing
RAM memory region.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200219160953.13771-42-imammedo@redhat.com>
Register 0x818 is documented as 'undefined', and register
0x82c is not documented. Refuse their access.
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200218063355.18577-5-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Only 24 bits of the PCIROR register are documented
(see pp. 37 of datasheet referenced in this file header).
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200218063355.18577-4-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Add a comment with the name of each register in the 0x800-0x8ff range.
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200218063355.18577-2-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The PARISC Lasi chipset emulation requires some of the common parallel
support and fails to build on a --without-default-devices:
LINK hppa-softmmu/qemu-system-hppa
/usr/bin/ld: hw/hppa/lasi.o: in function `lasi_init':
hw/hppa/lasi.c:324: undefined reference to `parallel_mm_init'
collect2: error: ld returned 1 exit status
make[1]: *** [Makefile:206: qemu-system-hppa] Error 1
Fixes: 376b851909
Reported-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200129192350.27143-1-philmd@redhat.com>
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Thomas Huth <thuth@redhat.com>
While loading the executable, some platforms (like AVR) need to
detect CPU type that executable is built for - and, with this patch,
this is enabled by reading the field 'e_flags' of the ELF header of
the executable in question. The change expands functionality of
the following functions:
- load_elf()
- load_elf_as()
- load_elf_ram()
- load_elf_ram_sym()
The argument added to these functions is called 'pflags' and is of
type 'uint32_t*' (that matches 'pointer to 'elf_word'', 'elf_word'
being the type of the field 'e_flags', in both 32-bit and 64-bit
variants of ELF header). Callers are allowed to pass NULL as that
argument, and in such case no lookup to the field 'e_flags' will
happen, and no information will be returned, of course.
CC: Richard Henderson <rth@twiddle.net>
CC: Peter Maydell <peter.maydell@linaro.org>
CC: Edgar E. Iglesias <edgar.iglesias@gmail.com>
CC: Michael Walle <michael@walle.cc>
CC: Thomas Huth <huth@tuxfamily.org>
CC: Laurent Vivier <laurent@vivier.eu>
CC: Philippe Mathieu-Daudé <f4bug@amsat.org>
CC: Aleksandar Rikalo <aleksandar.rikalo@rt-rk.com>
CC: Aurelien Jarno <aurelien@aurel32.net>
CC: Jia Liu <proljc@gmail.com>
CC: David Gibson <david@gibson.dropbear.id.au>
CC: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
CC: BALATON Zoltan <balaton@eik.bme.hu>
CC: Christian Borntraeger <borntraeger@de.ibm.com>
CC: Thomas Huth <thuth@redhat.com>
CC: Artyom Tarasenko <atar4qemu@gmail.com>
CC: Fabien Chouteau <chouteau@adacore.com>
CC: KONRAD Frederic <frederic.konrad@adacore.com>
CC: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Aleksandar Rikalo <aleksandar.rikalo@rt-rk.com>
Signed-off-by: Michael Rolnik <mrolnik@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <1580079311-20447-24-git-send-email-aleksandar.markovic@rt-rk.com>
The region in range [0xf0000000 - 0xf1000000] is the PDC area
(Processor Dependent Code), where the firmware is loaded.
This region has higher priority than the main memory.
When the machine has more than 3840MB of RAM, there is an
overlap. Since the PDC is closer to the CPU in the bus
hierarchy, it gets accessed first, and the CPU does not have
access to the RAM in this range.
To model the same behavior and keep a simple memory layout,
reduce the priority of the RAM region. The PDC region ends
overlapping the RAM.
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200109000525.24744-4-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The hardware expects DIMM slots of 1 or 2 GB, allowing up to
4 GB of memory. We want to accept the same amount of memory the
hardware can deal with. DIMMs of 768MB are not available.
However we have to deal with a firmware limitation: currently
SeaBIOS only supports 32-bit, and expects the RAM size in a
32-bit register. When using a 4GB configuration, the 32-bit
register get truncated and we report a size of 0MB to SeaBIOS,
which ends halting the machine:
$ qemu-system-hppa -m 4g -serial stdio
SeaBIOS: Machine configured with too little memory (0 MB), minimum is 16 MB.
SeaBIOS wants SYSTEM HALT.
The easiest way is to restrict the machine to 3GB of memory.
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200109000525.24744-3-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The firmware has to reside in the PDC range. If the Elf file
expects to load it below FIRMWARE_START, it is incorrect,
regardless the RAM size.
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200109000525.24744-2-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This adds emulation of Artist graphics good enough to get a text
console on both Linux and HP-UX. The X11 server from HP-UX also works.
Adjust boot-serial-test to disable graphics, so that SeaBIOS outputs
to the serial port, as expected by the test.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20191220211512.3289-6-svens@stackframe.org>
[rth: Merge Helge's test for machine->enable_graphics]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Most HP PA-RISC machines have a Digital DS21142/43 Tulip network card,
only some very latest generation machines have an e1000 NIC.
Since qemu now provides an emulated tulip card, use that one instead.
Signed-off-by: Helge Deller <deller@gmx.de>
Message-Id: <20191221222530.GB27803@ls3530.fritz.box>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20191220211512.3289-5-svens@stackframe.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
LASI is a built-in multi-I/O chip which supports serial, parallel,
network (Intel i82596 Apricot), sound and other functionalities.
LASI has been used in many HP PARISC machines.
This patch adds the necessary parts to allow Linux and HP-UX to detect
LASI and the network card.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20191220211512.3289-3-svens@stackframe.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The tests of the dino chip with the Online-diagnostics CD
("ODE DINOTEST") now succeeds.
Additionally add some qemu trace events.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191220211512.3289-2-svens@stackframe.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Remove the need to include i386/pc.h to get to the i8259 functions.
This is enough to remove the inclusion of hw/i386/pc.h from all non-x86
files.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The MC146818 is a Real Time Clock, not a timer.
Move it under the hw/rtc/ subdirectory.
Use copyright statement from 80cabfad16 for "hw/rtc/mc146818rtc.h".
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191003230404.19384-4-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
machine_hppa_init() violates memory_region_allocate_system_memory() contract
by calling it multiple times which could break with -mem-path. Replace
the second usage (for 'rom') with memory_region_init_ram() instead.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20191008113318.7012-4-imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
memory_region_init_* takes care of copying the name into memory it owns.
Free it in the caller.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 5400 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Almost a third of its inclusions are actually superfluous. Delete
them. Downgrade two more to qapi/qapi-types-run-state.h, and move one
from char/serial.h to char/serial.c.
hw/semihosting/config.c, monitor/monitor.c, qdev-monitor.c, and
stubs/semihost.c define variables declared in sysemu/sysemu.h without
including it. The compiler is cool with that, but include it anyway.
This doesn't reduce actual use much, as it's still included into
widely included headers. The next commit will tackle that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-27-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
In my "build everything" tree, changing hw/hw.h triggers a recompile
of some 2600 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
The previous commits have left only the declaration of hw_error() in
hw/hw.h. This permits dropping most of its inclusions. Touching it
now recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-19-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/irq.h triggers a recompile
of some 5400 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get qemu_irq and.or qemu_irq_handler.
Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed. Touching it now recompiles only some 500 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-13-armbru@redhat.com>
In my "build everything" tree, changing sysemu/reset.h triggers a
recompile of some 2600 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
The main culprit is hw/hw.h, which supposedly includes it for
convenience.
Include sysemu/reset.h only where it's needed. Touching it now
recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-9-armbru@redhat.com>
The global smp variables in alpha/hppa/mips/openrisc/sparc*/xtensa codes
are replaced with smp properties from MachineState.
A local variable of the same name would be introduced in the declaration
phase if it's used widely in the context OR replace it on the spot if it's
only used once. No semantic changes.
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190518205428.90532-10-like.xu@linux.intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
To get rid of the global smp_* variables we're currently using, it's recommended
to pass MachineState in the list of incoming parameters for functions that use
global smp variables, thus some redundant parameters are dropped. It's applied
for legacy smbios_*(), *_machine_reset(), hot_add_cpu() and mips *_create_cpu().
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190518205428.90532-3-like.xu@linux.intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
No header includes qemu-common.h after this commit, as prescribed by
qemu-common.h's file comment.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190523143508.25387-5-armbru@redhat.com>
[Rebased with conflicts resolved automatically, except for
include/hw/arm/xlnx-zynqmp.h hw/arm/nrf51_soc.c hw/arm/msf2-soc.c
block/qcow2-refcount.c block/qcow2-cluster.c block/qcow2-cache.c
target/arm/cpu.h target/lm32/cpu.h target/m68k/cpu.h target/mips/cpu.h
target/moxie/cpu.h target/nios2/cpu.h target/openrisc/cpu.h
target/riscv/cpu.h target/tilegx/cpu.h target/tricore/cpu.h
target/unicore32/cpu.h target/xtensa/cpu.h; bsd-user/main.c and
net/tap-bsd.c fixed up]
We spell out sub/dir/ in sub/dir/trace-events' comments pointing to
source files. That's because when trace-events got split up, the
comments were moved verbatim.
Delete the sub/dir/ part from these comments. Gets rid of several
misspellings.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190314180929.27722-3-armbru@redhat.com
Message-Id: <20190314180929.27722-3-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
When virtio-vga was added, the intention was to only support it for
those machines where the firmware does not know about virtio-gpu,
and supported VGA legacy hardware before virtio-{gpu,vga} were
introduced.
The Kconfig switch however enabled virtio-vga for all machines with
a PCI bus, and libvirt then prefers it even on hardware where
virtio-gpu would be preferrable. At least for now, only enable
virtio-vga for PC, hppa and pSeries machines, as was the case
before Kconfig dependencies were introduced.
Reported-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This fixes when configuring with CONFIG_PCI_DEVICES=n:
$ qemu-system-hppa
qemu-system-hppa: Unsupported NIC model: e1000
Fixes: 9483cf27dd
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190316200818.8265-14-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch fixes two issues in the hppa/parisc emulation:
1. The CPU HPA was wrong in the sense that we had negative module
offsets in the firmware-internal module table (which we ignored up to
now). Get it correct by changing the CPU HPA to 0xfffb0000 which is
greater than the DINO_HPA of 0xfff80000.
This change requires the seabios-firmware update.
2. Sven noticed that the FPU register cr10 is only able to reference up
to 8 FPUs, so let's reduce the maximum amount of SMP CPUs too.
Signed-off-by: Helge Deller <deller@gmx.de>
Message-Id: <20190315164130.GA7800@ls3530>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
%-softmmu.mak only keep boards and optional device
definitions in Kconfig mode.
Note that the Dino board uses a memory mapped 16550 UART and
therefore only CONFIG_SERIAL is needed, not CONFIG_SERIAL_ISA.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Kconfig files were generated mostly with this script:
for i in `grep -ho CONFIG_[A-Z0-9_]* default-configs/* | sort -u`; do
set fnord `git grep -lw $i -- 'hw/*/Makefile.objs' `
shift
if test $# = 1; then
cat >> $(dirname $1)/Kconfig << EOF
config ${i#CONFIG_}
bool
EOF
git add $(dirname $1)/Kconfig
else
echo $i $*
fi
done
sed -i '$d' hw/*/Kconfig
for i in hw/*; do
if test -d $i && ! test -f $i/Kconfig; then
touch $i/Kconfig
git add $i/Kconfig
fi
done
Whenever a symbol is referenced from multiple subdirectories, the
script prints the list of directories that reference the symbol.
These symbols have to be added manually to the Kconfig files.
Kconfig.host and hw/Kconfig were created manually.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-27-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
some versions of HP-UX 10.20 seems to rely on the fact that DINO
strips out the lower 2 bits of the PCI configuration address.
Also update the binary SeaBIOS distributed to the latest version
from Helge's repository, which is required with that change.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20190218183314.20157-1-svens@stackframe.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
HP-UX 10.20 uses busmaster writes to the CPU EIR to signal
interrupts from the SCSI constroller. (Similar to what is known
as MSI on x86)
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20190211192039.5457-1-svens@stackframe.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Add the new configs to default-configs/hppa-sofmmu.mak.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20190202072456.6468-23-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds an optional function pointer, 'elf_note_fn', to
load_elf() which causes load_elf() to additionally parse any
ELF program headers of type PT_NOTE and check to see if the ELF
Note is of the type specified by the 'translate_opaque' arg.
If a matching ELF Note is found then the specfied function pointer
is called to process the ELF note.
Passing a NULL function pointer results in ELF Notes being skipped.
The first consumer of this functionality is the PVHboot support
which needs to read the XEN_ELFNOTE_PHYS32_ENTRY ELF Note while
loading the uncompressed kernel binary in order to discover the
boot entry address for the x86/HVM direct boot ABI.
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Previously, if the size of initrd >=2G, qemu exits with error:
root@haswell-OptiPlex-9020:/home/lizj# /home/lizhijian/lkp/qemu-colo/x86_64-softmmu/qemu-system-x86_64 -kernel ./vmlinuz-4.16.0-rc4 -initrd large.cgz -nographic
qemu: error reading initrd large.cgz: No such file or directory
root@haswell-OptiPlex-9020:/home/lizj# du -sh large.cgz
2.5G large.cgz
this patch changes the caller side that use this function to calculate
size of initrd file as well.
v2: update error message and int64_t printing format
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Message-Id: <1536833233-14121-1-git-send-email-lizhijian@cn.fujitsu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As part of commits a64aa5785d "hw: Deprecate -drive if=scsi with non-onboard
HBAs" and b891538e81 "hw/ppc/prep: Fix implicit creation of "-drive if=scsi"
devices" the lsi53c895a_create() and lsi53c810_create() functions were added
to wrap pci_create_simple() and scsi_bus_legacy_handle_cmdline().
Unfortunately this prevents us from changing qdev properties on the device
and/or changing the PCI configuration. By switching over to using the new
lsi53c8xx_handle_legacy_cmdline() function then the caller can now configure
and realize the LSI SCSI device exactly as required.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Peter Maydell <peter.maydell@linaro.org> [arm parts]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
vDPA support, fix to vhost blk RO bit handling, some include path
cleanups, NFIT ACPI table.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbEXNvAAoJECgfDbjSjVRpc8gH/R8xrcFrV+k9wwbgYcOcGb6Y
LWjseE31pqJcxRV80vLOdzYEuLStZQKQQY7xBDMlA5vdyvZxIA6FLO2IsiJSbFAk
EK8pclwhpwQAahr8BfzenabohBv2UO7zu5+dqSvuJCiMWF3jGtPAIMxInfjXaOZY
odc1zY2D2EgsC7wZZ1hfraRbISBOiRaez9BoGDKPOyBY9G1ASEgxJgleFgoBLfsK
a1XU+fDM6hAVdxftfkTm0nibyf7PWPDyzqghLqjR9WXLvZP3Cqud4p8N29mY51pR
KSTjA4FYk6Z9EVMltyBHfdJs6RQzglKjxcNGdlrvacDfyFi79fGdiosVllrjfJM=
=3+V0
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
acpi, vhost, misc: fixes, features
vDPA support, fix to vhost blk RO bit handling, some include path
cleanups, NFIT ACPI table.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 01 Jun 2018 17:25:19 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (31 commits)
vhost-blk: turn on pre-defined RO feature bit
ACPI testing: test NFIT platform capabilities
nvdimm, acpi: support NFIT platform capabilities
tests/.gitignore: add entry for generated file
arch_init: sort architectures
ui: use local path for local headers
qga: use local path for local headers
colo: use local path for local headers
migration: use local path for local headers
usb: use local path for local headers
sd: fix up include
vhost-scsi: drop an unused include
ppc: use local path for local headers
rocker: drop an unused include
e1000e: use local path for local headers
ioapic: fix up includes
ide: use local path for local headers
display: use local path for local headers
trace: use local path for local headers
migration: drop an unused include
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When pulling in headers that are in the same directory as the C file (as
opposed to one in include/), we should use its relative path, without a
directory.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180528232719.4721-19-f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As part of plumbing MemTxAttrs down to the IOMMU translate method,
add MemTxAttrs as an argument to the MemoryRegion valid.accepts
callback. We'll need this for subpage_accepts().
We could take the approach we used with the read and write
callbacks and add new a new _with_attrs version, but since there
are so few implementations of the accepts hook we just change
them all.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180521140402.23318-9-peter.maydell@linaro.org
Change all the uses of serial_hds[] to go via the new
serial_hd() function. Code change produced with:
find hw -name '*.[ch]' | xargs sed -i -e 's/serial_hds\[\([^]]*\)\]/serial_hd(\1)/g'
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180420145249.32435-8-peter.maydell@linaro.org
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Now that we have the prerequisites in target/hppa/,
implement the hardware for a PA7100LC.
This also enables build for hppa-softmmu.
Signed-off-by: Helge Deller <deller@gmx.de>
[rth: Since it is all new code, squashed all branch development
withing hw/hppa/ to a single patch.]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
With the addition of default-configs/hppa-softmmu.mak, this
will compile. It is not enabled with this patch, however.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
