PAGE_SIZE is undefined on ARM64. Use XC_PAGE_SIZE instead, which is
always 4096 even when page granularity is 64K.
For this to actually work with 64K pages, more changes are required.
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Reviewed-by: Juergen Gross <jgross@suse.com>
Release-acked-by: Wei Liu <wei.liu2@citrix.com>
Needed to make sure usb redirection is prepared to actually handle the
callback from the usb host adapter. Without this interrupt endpoints
don't work on xhci.
Note: On ehci the usb_wakeup() call only schedules a BH for the actual
work, which hides this bug because the allocation happens before ehci
calls back even without this patch.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Message-id: 1476096313-7730-1-git-send-email-kraxel@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The default DMA offset is set to 3. When the property is not set by
the consumer, the default causes DMA access to be shifted by 3
bytes. In PXA, this results in incorrect DMA access, leading to error
notification in the USB controller driver. A better default would be
0, so that there is no offset, when the consumer does not specify one.
Signed-off-by: Vijay Kumar B. <vijaykumar@zilogic.com>
Reviewed-by: Deepak S. <deepak@zilogic.com>
Message-id: 1475060958-7760-1-git-send-email-vijaykumar@zilogic.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
snprintf return value is *not* the number of chars written into the
buffer, but the number of chars needed. So in case the buffer is too
small you can go alloc a bigger one and try again. But that also means
you can't simply use the return value for the next snprintf call
without checking beforehand that things did actually fit.
Problem is that usb_desc_create_serial didn't perform that check, so a
loooong path string (can happen with deep pci-bridge nesting) results in
the third snprintf call smashing the stack.
Fix this by throwing out all the snpintf calls and use g_strdup_printf
instead.
https://bugzilla.redhat.com/show_bug.cgi?id=1381630
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 1475659998-22045-1-git-send-email-kraxel@redhat.com
All callsites have a XHCIEPContext pointer anyway, so we can just pass
it directly instead of fiddeling with slotid and epid.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1474965172-30321-9-git-send-email-kraxel@redhat.com
xhci_kick_epctx is a xhci_kick_ep variant which takes an XHCIEPContext
as input instead of slotid and epid. So in case we have a XHCIEPContext
at hand at the callsite we can just pass it directly.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1474965172-30321-7-git-send-email-kraxel@redhat.com
xhci has a fixed number of 24 (TD_QUEUE) XHCITransfer structs per
endpoint, which turns out to be a problem for usb3 devices with 32 (or
more) bulk streams. xhci re-checks the trb rings on every finished
transfer to make sure it'll pick up any pending work. But that scheme
breaks in case the first transfer of a ring can't be started because we
ran out of XHCITransfer structs already.
So remove static XHCITransfer array from XHCIEPContext. Use a linked
list instead, and allocate/free XHCITransfer as needed. Add helper
functions to allocate & initialize and to cleanup & release
XHCITransfer structs. That also simplifies trb management, we never
have to realloc XHCITransfer->trbs because we don't reuse XHCITransfer
structs any more.
New dynamic limit for in-flight xhci transfers per endpoint is
number-of-streams + 16.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1474965172-30321-5-git-send-email-kraxel@redhat.com
EV_QUEUE must not change because an array of that size is part of live
migration data. Hard-code current value there, so we can touch TD_QUEUE
without breaking live migration.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1474965172-30321-3-git-send-email-kraxel@redhat.com
Needed to avoid we run in circles forever in case the guest builds
an endless loop with link trbs.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Tested-by: P J P <ppandit@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1476096382-7981-1-git-send-email-kraxel@redhat.com
While processing isochronous transfer descriptors(iTD), if the page
select(PG) field value is out of bands it will return. In this
situation the ehci's sg list is not freed thus leading to a memory
leak issue. This patch avoid this.
Signed-off-by: Li Qiang <liqiang6-s@360.cn>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Windows uses object properties to determine the size of a file, so to
add object properties, we must also add a minimum set of new commands
and object properties. Most object properties are data that we already
have, except for the unique persistant object identifier. Windows
doesn't use this property, it seems, so we can cheat a bit and just use
the object handle for it.
Signed-off-by: Isaac Lozano <109lozanoi@gmail.com>
Message-id: a741d0dd380cd7eb1695e1eb34ee6f341183f20a.1470477265.git.109lozanoi@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
MTP requires that if a file is larger than 4gb or if sending data larger
than 4gb, that the length field be set to 0xFFFFFFFF.
Also widened a couple variables to prevent overflow errors.
Signed-off-by: Isaac Lozano <109lozanoi@gmail.com>
Message-id: 01ad8ec7775f58575801ac3f13716f553a16815e.1470477265.git.109lozanoi@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The qemu_chr_fe_write method will return -1 on EAGAIN if the
chardev backend write would block. Almost no callers of the
qemu_chr_fe_write() method check the return value, instead
blindly assuming data was successfully sent. In most cases
this will lead to silent data loss on interactive consoles,
but in some cases (eg RNG EGD) it'll just cause corruption
of the protocol being spoken.
We unfortunately can't fix the virtio-console code, due to
a bug in the Linux guest drivers, which would cause the
entire Linux kernel to hang if we delay processing of the
incoming data in any way. Fixing this requires first fixing
the guest driver to not hold spinlocks while writing to the
hvc device backend.
Fixes bug: https://bugs.launchpad.net/qemu/+bug/1586756
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1473170165-540-4-git-send-email-berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If the xhci uses msix, it doesn't free the corresponding
memory, thus leading a memory leak. This patch avoid this.
Signed-off-by: Li Qiang <liqiang6-s@360.cn>
Message-id: 57d7d2e0.d4301c0a.d13e9.9a55@mx.google.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The companion descriptor is present on all usb3 devices, not only
those with streams support. We need to check attributes to see
whenever the device uses streams or not.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1473406890-30164-1-git-send-email-kraxel@redhat.com
Previously the code would incorrectly report the remainder as 8 bytes. A
remainder of 0 bytes should be reported when the SETUP packet is
successfully transferred. Found using FreeBSD's XHCI driver.
Signed-off-by: Hans Petter Selasky <hps@selasky.org>
[ kraxel: codestyle fixup ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
qdev_get_dev_path() returns an allocated string, free it when no longer
needed.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
The list is created during instance init and further populated with
usb_desc_set_string(). Clear it when unrealizing the device.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
When unplugging a device in the Xen pvusb backend drain the submit
queue before deallocation of the control structures. Otherwise there
will be bogus memory accesses when I/O contracts are finished.
Correlated to this issue is the handling of cancel requests: a packet
cancelled will still lead to the call of complete, so add a flag
to the request indicating it should be just dropped on complete.
Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Message-id: 1470140044-16492-3-git-send-email-jgross@suse.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
ehci_update_frindex takes time linearly proportional to a number
of uframes to calculate new frame index and raise FLR interrupts,
which is a problem for large amounts of uframes.
If we experience large delays between echi timer callbacks (i.e. because
other periodic handlers have taken a lot of time to complete) we
get a lot of skipped frames which then delay ehci timer callback more
and this leads to deadlocking the system when ehci schedules next
callback to be too soon.
Observable behaviour is qemu consuming 100% host CPU time while guest
is unresponsive. This misbehavior could happen for a while and QEMU does
not get out from this state automatically without the patch.
This change makes ehci_update_frindex execute in constant time.
Signed-off-by: Evgeny Yakovlev <eyakovlev@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Message-id: 1469638520-32706-1-git-send-email-den@openvz.org
CC: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
libusb.h uses the WINAPI calling convention for all function callbacks.
Cross compilation with Mingw-w64 on Cygwin fails when this calling
convention is missing.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Message-id: 1469775331-7468-1-git-send-email-sw@weilnetz.de
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The local variable i is unsed for Windows.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Message-id: 1469775569-7869-1-git-send-email-sw@weilnetz.de
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Enabled by default, can be used to turn off (usb3) streams support.
xhci has a such a property too (same name, same default).
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1468408474-17648-1-git-send-email-kraxel@redhat.com
A static analysis tool called BEAM detected possible side effect from
assert() calling a helper which may change an XHCI ring after every call.
This moves xhci_ring_fetch() out of assert() so it will be called
with and without enabled debug.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-id: 1468812548-31868-1-git-send-email-aik@ozlabs.ru
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
is_netdev is only used as a bool, so make it one.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1468468228-27827-14-git-send-email-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
This is a mostly-mechanical conversion that creates a new flat
union 'Netdev' QAPI type that covers all the branches of the
former 'NetClientOptions' simple union, where the branches are
now listed in a new 'NetClientDriver' enum rather than generated
from the simple union. The existence of a flat union has no
change to the command line syntax accepted for new code, and
will make it possible for a future patch to switch the QMP
command to parse a boxed union for no change to valid QMP; but
it does have some ripple effect on the C code when dealing with
the new types.
While making the conversion, note that the 'NetLegacy' type
remains unchanged: it applies only to legacy command line options,
and will not be ported to QMP, so it should remain a wrapper
around a simple union; to avoid confusion, the type named
'NetClientOptions' is now gone, and we introduce 'NetLegacyOptions'
in its place. Then, in the C code, we convert from NetLegacy to
Netdev as soon as possible, so that the bulk of the net stack
only has to deal with one QAPI type, not two. Note that since
the old legacy code always rejected 'hubport', we can just omit
that branch from the new 'NetLegacyOptions' simple union.
Based on an idea originally by Zoltán Kővágó <DirtY.iCE.hu@gmail.com>:
Message-Id: <01a527fbf1a5de880091f98cf011616a78adeeee.1441627176.git.DirtY.iCE.hu@gmail.com>
although the sed script in that patch no longer applies due to
other changes in the tree since then, and I also did some manual
cleanups (such as fixing whitespace to keep checkpatch happy).
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1468468228-27827-13-git-send-email-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Fixup from Eric squashed in]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
As cache.writeback is a BlockBackend property and as such more related
to the guest device than the BlockDriverState, we already removed it
from the blockdev-add interface. This patch adds the new way to set it,
as a qdev property of the corresponding guest device.
For example: -drive if=none,file=test.img,node-name=img
-device ide-hd,drive=img,write-cache=off
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
If a node name instead of a BlockBackend name is specified as the driver
for a guest device, an anonymous BlockBackend is created now.
The order of operations in release_drive() must be reversed in order to
avoid a use-after-free bug because now blk_detach_dev() frees the last
reference if an anonymous BlockBackend is used.
usb-storage uses a hack where it forwards its BlockBackend as a property
to another device that it internally creates. This hack must be updated
so that it doesn't drop its original BB before it can be passed to the
other device. This used to work because we always had the monitor
reference around, but with node-names the device reference is the only
one now.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Header guard symbols should match their file name to make guard
collisions less likely. Offenders found with
scripts/clean-header-guards.pl -vn.
Cleaned up with scripts/clean-header-guards.pl, followed by some
renaming of new guard symbols picked by the script to better ones.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Tracked down with an ugly, brittle and probably buggy Perl script.
Also move includes converted to <...> up so they get included before
ours where that's obviously okay.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Tested-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
This patch is a rough fix to "hw/usb/core.c:401: usb_handle_packet:
Assertion `dev->state == 3' failed.". Qemu will crash when a usb3
device redirect to Windows7 VM via nec-usb-xhci.
In extensible-host-controler-interface-usb-xhci.pdf P94(4.6.5
Address Device):
• If the Block Set Address Request (BSR) flag = ‘1’
• If the slot is in the Enabled state:
...
• Set the Slot State in the Output Slot Context to Default.
BSR = ‘1’: Enabled state to Default state; BSR = ‘0’: Default state
to Addressed state. Try to call usb_device_reset to set device state
to USB_STATE_DEFAULT in xhci_address_slot wether bsr is zero.
Signed-off-by: Zhang Shuaiyi <zhang_syi@massclouds.com>
Message-id: 1467258640-11921-1-git-send-email-zhang_syi@massclouds.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
msi_init() reports errors with error_report(), which is wrong
when it's used in realize().
Fix by converting it to Error.
Fix its callers to handle failure instead of ignoring it.
For those callers who don't handle the failure, it might happen:
when user want msi on, but he doesn't get what he want because of
msi_init fails silently.
cc: Gerd Hoffmann <kraxel@redhat.com>
cc: John Snow <jsnow@redhat.com>
cc: Dmitry Fleytman <dmitry@daynix.com>
cc: Jason Wang <jasowang@redhat.com>
cc: Michael S. Tsirkin <mst@redhat.com>
cc: Hannes Reinecke <hare@suse.de>
cc: Paolo Bonzini <pbonzini@redhat.com>
cc: Alex Williamson <alex.williamson@redhat.com>
cc: Markus Armbruster <armbru@redhat.com>
cc: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
>From bit to enum OnOffAuto
cc: Gerd Hoffmann <kraxel@redhat.com>
cc: Michael S. Tsirkin <mst@redhat.com>
cc: Markus Armbruster <armbru@redhat.com>
cc: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Make attached property settable and turns off auto-attach in case the
device was hotplugged. Hotplugging works simliar to usb-bot now.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: 1465984019-28963-6-git-send-email-kraxel@redhat.com
This patch marks usb-bot as hot-pluggable device, makes attached
property settable and turns off auto-attach in case the device
was hotplugged.
Hot-plugging a usb-bot device with one or more scsi devices can be
done this way now:
(1) device-add usb-bot,id=foo
(2) device-add scsi-{hd,cd},bus=foo.0,lun=0
(2b) optionally add more devices (luns 0 ... 15).
(3) qom-set foo.attached = true
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: 1465984019-28963-5-git-send-email-kraxel@redhat.com
USB devices in attached state are visible to the guest. This patch adds
a QOM property for this. Write access is opt-in per device. Some
devices manage attached state automatically (usb-host, usb-serial,
usb-redir), so we can't enable write access universally but have to do
it on a case by case base. So far, no device opts in.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: 1465984019-28963-4-git-send-email-kraxel@redhat.com
[ minor codestyle fix ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Version: GnuPG v1
iQEcBAABAgAGBQJXaFInAAoJEJykq7OBq3PI6VsH/0Sfgbdo1RksYuQwb/y92sCW
EN+lxUZ+OLfgrc8PYgNZwfSM3rsfYhznL0MAXOeEe7Ahabi07w7DhGR8WvwfAOlI
G96FRuvrIPfv5u6U6fwS4CvG3TIHVLxfHKCsTpPUmH8U5CNx/x/tpjNiWN1dj6t+
sXybSjYHfZfiZy2tI9MFIFWCdxnF/pl0QAPhbRqc8Y/RQTDrPKRjLpz+nitN/u96
5TS7KlELyQuP91YMmLceYSmIkHbxW703h+iE2n4hov0uZCP8Jil+2Jsd3ziQSRlL
j6LqexQ2ViBGdDSfiZGYES2VPlsHOCwb4G+IgWBStfZg1ppaXENvcDzPrgrB+L4=
=eUnF
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanha/tags/tracing-pull-request' into staging
# gpg: Signature made Mon 20 Jun 2016 21:29:27 BST
# gpg: using RSA key 0x9CA4ABB381AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>"
# Primary key fingerprint: 8695 A8BF D3F9 7CDA AC35 775A 9CA4 ABB3 81AB 73C8
* remotes/stefanha/tags/tracing-pull-request: (42 commits)
trace: split out trace events for linux-user/ directory
trace: split out trace events for qom/ directory
trace: split out trace events for target-ppc/ directory
trace: split out trace events for target-s390x/ directory
trace: split out trace events for target-sparc/ directory
trace: split out trace events for net/ directory
trace: split out trace events for audio/ directory
trace: split out trace events for ui/ directory
trace: split out trace events for hw/alpha/ directory
trace: split out trace events for hw/arm/ directory
trace: split out trace events for hw/acpi/ directory
trace: split out trace events for hw/vfio/ directory
trace: split out trace events for hw/s390x/ directory
trace: split out trace events for hw/pci/ directory
trace: split out trace events for hw/ppc/ directory
trace: split out trace events for hw/9pfs/ directory
trace: split out trace events for hw/i386/ directory
trace: split out trace events for hw/isa/ directory
trace: split out trace events for hw/sd/ directory
trace: split out trace events for hw/sparc/ directory
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move all trace-events for files in the hw/usb/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-15-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
error_propagate() already ignores local_err==NULL, so there's no
need to check it before calling.
Coccinelle patch used to perform the changes added to
scripts/coccinelle/error_propagate_null.cocci.
Reviewed-by: Eric Blake <eblake@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1465855078-19435-2-git-send-email-ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
qemu/osdep.h checks whether MAP_ANONYMOUS is defined, but this check
is bogus without a previous inclusion of sys/mman.h. Include it in
sysemu/os-posix.h and remove it from everywhere else.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Use stl_le_p() and ldl_le_p() to read and write data from
buffers, rather than using pointer casts and cpu_to_le32()
for writes and le32_to_cpup() for reads. This:
* avoids lots of casts
* works even if the buffer isn't as aligned as the host would like
* avoids using the *_to_cpup() functions which we want to get rid of
Note that there may still be some places where a pointer from the
guest is cast to a pointer to a host structure; these would also
have to be changed for the device to work on a host CPU which
enforces alignment restrictions.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 1465573077-29221-1-git-send-email-peter.maydell@linaro.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch changes usb-host behavior in case we hostbus= and hostaddr=
properties are used to identify the usb device in question. Instead of
adding the device to the hotplug watchlist we try to open directly using
the given bus number and device address.
Putting a device specified by hostaddr to the hotplug watchlist isn't
a great idea as the address isn't a fixed property. It changes every
time the device is plugged in. So considering this case as "use the
device at bus:addr _now_" is more sane. Also usb-host will throw errors
in case it can't initialize the host device.
Note: For devices on the hotplug watchlist (hostport or vendorid or
productid specified) qemu continues to ignore errors and keeps
monitoring the usb bus to see if the device eventually shows up.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1464945175-28939-1-git-send-email-kraxel@redhat.com
Replace (((n) + (d) - 1) /(d)) by DIV_ROUND_UP(n,d).
This patch is the result of coccinelle script
scripts/coccinelle/round.cocci
CC: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
muldiv64(a, 1, b) is like "a / b".
This patch is the result of coccinelle script
scripts/coccinelle/remove_muldiv64.cocci.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
muldiv64() is "uint64_t muldiv64(uint64_t a, uint32_t b, uint32_t c)"
Some time it is used as muldiv64(uint32_t a, uint64_t b, uint32_t c)"
This patch is the result of coccinelle script
scripts/coccinelle/swap_muldiv64.cocci to reorder arguments.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
QEMU currently crashes when an OHCI controller is instantiated with
too many ports, e.g. "-device pci-ohci,num-ports=100,masterbus=1".
Thus add a proper check in usb_ohci_init() to make sure that we
do not use more than OHCI_MAX_PORTS = 15 ports here.
Ticket: https://bugs.launchpad.net/qemu/+bug/1581308
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-id: 1463995387-11710-1-git-send-email-thuth@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add a backend for para-virtualized USB devices for xen domains.
The backend is using host-libusb to forward USB requests from a
domain via libusb to the real device(s) passed through.
Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Message-id: 1463062421-613-4-git-send-email-jgross@suse.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This is a hack to support compilation with Mingw-w64 which provides
a libusb-1.0 package, but no poll.h.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Message-id: 1458630800-10088-1-git-send-email-sw@weilnetz.de
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
If an application uses libmtp on the guest system,
it will complain with the warning message:
LIBMTP WARNING: VendorExtensionID: ffffffff
LIBMTP WARNING: VendorExtensionDesc: (null)
LIBMTP WARNING: this typically means the device is PTP (i.e. a camera) but
not a MTP device at all. Trying to continue anyway.
This is because libmtp expects a MTP Vendor Extension ID of 0x00000006 and a
MTP Version of 0x0064. These numbers are taken from Microsoft's MTP Vendor
Extension Identification Message page and are what most physical devices
show.
Signed-off-by: Isaac Lozano <109lozanoi@gmail.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1460892593-5908-1-git-send-email-109lozanoi@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch is a rough fix to a memory corruption we are observing when
running VMs with xhci USB controller and OVMF firmware.
Specifically, on the following call chain
xhci_reset
xhci_disable_slot
xhci_disable_ep
xhci_set_ep_state
QEMU overwrites guest memory using stale guest addresses.
This doesn't happen when the guest (firmware) driver sets up xhci for
the first time as there are no slots configured yet. However when the
firmware hands over the control to the OS some slots and endpoints are
already set up with their context in the guest RAM. Now the OS' driver
resets the controller again and xhci_set_ep_state then reads and writes
that memory which is now owned by the OS.
As a quick fix, skip calling xhci_set_ep_state in xhci_disable_ep if the
device context base address array pointer is zero (indicating we're in
the HC reset and no DMA is possible).
Cc: qemu-stable@nongnu.org
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Message-id: 1462384435-1034-1-git-send-email-rkagan@virtuozzo.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
commit "5f77e06 usb: add pid check at the first of uhci_handle_td()"
moved the pid verification to the start of the uhci_handle_td function,
to simplify the error handling (we don't have to free stuff which we
didn't allocate in the first place ...).
Problem is now the check fires too often, it raises error IRQs even for
TDs which we are not going to process because they are not set active.
So, lets move down the check a bit, so it is done only for active TDs,
but still before we are going to allocate stuff to process the requested
transfer.
Reported-by: Joe Clifford <joe@thunderbug.co.uk>
Tested-by: Joe Clifford <joe@thunderbug.co.uk>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1461321893-15811-1-git-send-email-kraxel@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
All callers pass "false" keeping the old semantics. The windows
implementation doesn't distinguish the flag yet. On posix, it is passed
down to the underlying aio context.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Commit "156a2e4 ehci: make idt processing more robust" tries to avoid a
DoS by the guest (create a circular iTD queue and let qemu ehci
emulation run in circles forever). Unfortunately this has two problems:
First it misses the case of siTDs, and second it reportedly breaks
FreeBSD.
So lets go for a different approach: just count the number of iTDs and
siTDs we have seen per frame and apply a limit. That should really
catch all cases now.
Reported-by: 杜少博 <dushaobo@360.cn>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
* Chardev fix from Marc-André
* config.status tweak from David
* Header file tweaks from Markus, myself and Veronia (Outreachy candidate)
* get_ticks_per_sec() removal from Rutuja (Outreachy candidate)
* Coverity fix from myself
* PKE implementation from myself, based on rth's XSAVE support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJW9ErPAAoJEL/70l94x66DJfEH/A/QkMpAhrgNdyVsahzsGrzE
wx5gHFIc1nBYxyr62w4apUb5jPB7zaXu0LA7EAWDeAe0pyP8hZzLT9kJyOEDsuJu
zwKN2QeLSNMtPbnbKN0I/YQ2za2xX1V5ruhSeOJoVslUI214hgnAURaGshhQNzuZ
2CluDT9KgL5cQifAnKs5kJrwhIYShYNQB+1eDC/7wk28dd/EH+sPALIoF+rqrSmt
Zu4Mdqd+9Ns+oKOjA6br9ULq/Hzg0aDfY82J+XLVVqfF3PXQe8rTDmuMf/7jTn+M
Un7ZOcei9oZF2/9vfAfKQpDCcgD9HvOUSbgqV/ubmkPPmN/LNJzeKj0fBhrRN+Y=
=K12D
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* Log filtering from Alex and Peter
* Chardev fix from Marc-André
* config.status tweak from David
* Header file tweaks from Markus, myself and Veronia (Outreachy candidate)
* get_ticks_per_sec() removal from Rutuja (Outreachy candidate)
* Coverity fix from myself
* PKE implementation from myself, based on rth's XSAVE support
# gpg: Signature made Thu 24 Mar 2016 20:15:11 GMT using RSA key ID 78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
* remotes/bonzini/tags/for-upstream: (28 commits)
target-i386: implement PKE for TCG
config.status: Pass extra parameters
char: translate from QIOChannel error to errno
exec: fix error handling in file_ram_alloc
cputlb: modernise the debug support
qemu-log: support simple pid substitution for logs
target-arm: dfilter support for in_asm
qemu-log: dfilter-ise exec, out_asm, op and opt_op
qemu-log: new option -dfilter to limit output
qemu-log: Improve the "exec" TB execution logging
qemu-log: Avoid function call for disabled qemu_log_mask logging
qemu-log: correct help text for -d cpu
tcg: pass down TranslationBlock to tcg_code_gen
util: move declarations out of qemu-common.h
Replaced get_tick_per_sec() by NANOSECONDS_PER_SECOND
hw: explicitly include qemu-common.h and cpu.h
include/crypto: Include qapi-types.h or qemu/bswap.h instead of qemu-common.h
isa: Move DMA_transfer_handler from qemu-common.h to hw/isa/isa.h
Move ParallelIOArg from qemu-common.h to sysemu/char.h
Move QEMU_ALIGN_*() from qemu-common.h to qemu/osdep.h
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Conflicts:
scripts/clean-includes
Move declarations out of qemu-common.h for functions declared in
utils/ files: e.g. include/qemu/path.h for utils/path.c.
Move inline functions out of qemu-common.h and into new files (e.g.
include/qemu/bcd.h)
Signed-off-by: Veronia Bahaa <veroniabahaa@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch replaces get_ticks_per_sec() calls with the macro
NANOSECONDS_PER_SECOND. Also, as there are no callers, get_ticks_per_sec()
is then removed. This replacement improves the readability and
understandability of code.
For example,
timer_mod(fdctrl->result_timer,
qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) + (get_ticks_per_sec() / 50));
NANOSECONDS_PER_SECOND makes it obvious that qemu_clock_get_ns
matches the unit of the expression on the right side of the plus.
Signed-off-by: Rutuja Shah <rutu.shah.26@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 57cb38b included qapi/error.h into qemu/osdep.h to get the
Error typedef. Since then, we've moved to include qemu/osdep.h
everywhere. Its file comment explains: "To avoid getting into
possible circular include dependencies, this file should not include
any other QEMU headers, with the exceptions of config-host.h,
compiler.h, os-posix.h and os-win32.h, all of which are doing a
similar job to this file and are under similar constraints."
qapi/error.h doesn't do a similar job, and it doesn't adhere to
similar constraints: it includes qapi-types.h. That's in excess of
100KiB of crap most .c files don't actually need.
Add the typedef to qemu/typedefs.h, and include that instead of
qapi/error.h. Include qapi/error.h in .c files that need it and don't
get it now. Include qapi-types.h in qom/object.h for uint16List.
Update scripts/clean-includes accordingly. Update it further to match
reality: replace config.h by config-target.h, add sysemu/os-posix.h,
sysemu/os-win32.h. Update the list of includes in the qemu/osdep.h
comment quoted above similarly.
This reduces the number of objects depending on qapi/error.h from "all
of them" to less than a third. Unfortunately, the number depending on
qapi-types.h shrinks only a little. More work is needed for that one.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
[Fix compilation without the spice devel packages. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
USB Ehci emulation supports host controller capability registers.
But its mmio '.write' function was missing, which lead to a null
pointer dereference issue. Add a do nothing 'ehci_caps_write'
definition to avoid it; Do nothing because capability registers
are Read Only(RO).
Reported-by: Zuozhi Fzz <zuozhi.fzz@alibaba-inc.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 1454072434-16045-1-git-send-email-ppandit@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
inotify_init1 usage was guarded by a check for linux but does not
exist on older distributions like CentOS 5 resulting in build
failures.
Signed-off-by: Matthew Fortune <matthew.fortune@imgtec.com>
Message-id: 6D39441BF12EF246A7ABCE6654B023536BB85D4A@hhmail02.hh.imgtec.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
All the callers for xhci_dma_write_u32s() are using mostly 5 * uint32_t
in len. To avoid unbound stack warning for the function, make it
statically allocated, and assert when it's not big enough in the
future.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-id: 1457661106-9569-1-git-send-email-peterx@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Mingw-w64 does not provide sys/ioctl.h and Linux builds don't need it,
so remove that include statement.
ERROR is defined by wingdi.h (included via windows.h). Undefine it before
it is redefined to avoid a compiler warning / error.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Message-id: 1458159439-32322-1-git-send-email-sw@weilnetz.de
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
If dropping packets, data is freed, the caller's loop should not continue.
Reported by ccc-analyzer.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-id: 1456301288-1592-1-git-send-email-famz@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Allocate timer once, at init time, instead of allocating/freeing
it all the time when starting/stopping the bus. Simplifies the
code, also fixes bugs (memory leak) due to missing checks whenever
the time is already allocated or not.
Cc: Prasad J Pandit <pjp@fedoraproject.org>
Reported-by: Zuozhi Fzz <zuozhi.fzz@alibaba-inc.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
pid can be gotten from uhci device memory in uhci_handle_td(),
so the guest can trigger assert qemu if we get an invalid pid.
And the uhci spec 2.1.2 tells us The Host Controller sets Host
Controller Process Error bit to 1 when it detects a fatal error
and indicates that the Host Controller suffered a consistency
check failure while processing a Transfer Descriptor. An example
of a consistency check failure would be finding an illegal PID
field while processing the packet header portion of the TD.
When this error occurs, the Host Controller clears the Run/Stop
bit in the Command register to prevent further schedule execution.
We'd better to set UHCI_STS_HCPERR and kick an interrupt, check
the pid value at the first of uhci_handle_td function.
https://bugzilla.redhat.com/show_bug.cgi?id=1070027
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Message-id: 1455867238-4720-1-git-send-email-arei.gonglei@huawei.com
[ applied minor codestyle fix ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When processing remote NDIS control message packets,
the USB Net device emulator uses a fixed length(4096) data buffer.
The incoming informationBufferOffset & Length combination could
overflow and cross that range. Check control message buffer
offsets and length to avoid it.
Reported-by: Qinghao Tang <luodalongde@gmail.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 1455648821-17340-3-git-send-email-ppandit@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When processing remote NDIS control message packets, the USB Net
device emulator uses a fixed length(4096) data buffer. The incoming
packet length could exceed this limit. Add a check to avoid it.
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 1455648821-17340-2-git-send-email-ppandit@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The TUSB6010 is a USB controller (as the name suggests). Move it from
hw/timer (where it was accidentally filed in 2013 when we moved
everything out of hw/) to hw/usb.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1455883404-10976-1-git-send-email-peter.maydell@linaro.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When processing remote NDIS control message packets, the USB Net
device emulator checks to see if the USB configuration descriptor
object is of RNDIS type(2). But it does not check if it is null,
which leads to a null dereference error. Add check to avoid it.
Reported-by: Qinghao Tang <luodalongde@gmail.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 1455188480-14688-1-git-send-email-ppandit@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Similar to the previous patch, it's nice to have all functions
in the tree that involve a visitor and a name for conversion to
or from QAPI to consistently stick the 'name' parameter next
to the Visitor parameter.
Done by manually changing include/qom/object.h and qom/object.c,
then running this Coccinelle script and touching up the fallout
(Coccinelle insisted on adding some trailing whitespace).
@ rule1 @
identifier fn;
typedef Object, Visitor, Error;
identifier obj, v, opaque, name, errp;
@@
void fn
- (Object *obj, Visitor *v, void *opaque, const char *name,
+ (Object *obj, Visitor *v, const char *name, void *opaque,
Error **errp) { ... }
@@
identifier rule1.fn;
expression obj, v, opaque, name, errp;
@@
fn(obj, v,
- opaque, name,
+ name, opaque,
errp)
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1454075341-13658-20-git-send-email-eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
JSON uses "name":value, but many of our visitor interfaces were
called with visit_type_FOO(v, &value, name, errp). This can be
a bit confusing to have to mentally swap the parameter order to
match JSON order. It's particularly bad for visit_start_struct(),
where the 'name' parameter is smack in the middle of the
otherwise-related group of 'obj, kind, size' parameters! It's
time to do a global swap of the parameter ordering, so that the
'name' parameter is always immediately after the Visitor argument.
Additional reason in favor of the swap: the existing include/qjson.h
prefers listing 'name' first in json_prop_*(), and I have plans to
unify that file with the qapi visitors; listing 'name' first in
qapi will minimize churn to the (admittedly few) qjson.h clients.
Later patches will then fix docs, object.h, visitor-impl.h, and
those clients to match.
Done by first patching scripts/qapi*.py by hand to make generated
files do what I want, then by running the following Coccinelle
script to affect the rest of the code base:
$ spatch --sp-file script `git grep -l '\bvisit_' -- '**/*.[ch]'`
I then had to apply some touchups (Coccinelle insisted on TAB
indentation in visitor.h, and botched the signature of
visit_type_enum() by rewriting 'const char *const strings[]' to
the syntactically invalid 'const char*const[] strings'). The
movement of parameters is sufficient to provoke compiler errors
if any callers were missed.
// Part 1: Swap declaration order
@@
type TV, TErr, TObj, T1, T2;
identifier OBJ, ARG1, ARG2;
@@
void visit_start_struct
-(TV v, TObj OBJ, T1 ARG1, const char *name, T2 ARG2, TErr errp)
+(TV v, const char *name, TObj OBJ, T1 ARG1, T2 ARG2, TErr errp)
{ ... }
@@
type bool, TV, T1;
identifier ARG1;
@@
bool visit_optional
-(TV v, T1 ARG1, const char *name)
+(TV v, const char *name, T1 ARG1)
{ ... }
@@
type TV, TErr, TObj, T1;
identifier OBJ, ARG1;
@@
void visit_get_next_type
-(TV v, TObj OBJ, T1 ARG1, const char *name, TErr errp)
+(TV v, const char *name, TObj OBJ, T1 ARG1, TErr errp)
{ ... }
@@
type TV, TErr, TObj, T1, T2;
identifier OBJ, ARG1, ARG2;
@@
void visit_type_enum
-(TV v, TObj OBJ, T1 ARG1, T2 ARG2, const char *name, TErr errp)
+(TV v, const char *name, TObj OBJ, T1 ARG1, T2 ARG2, TErr errp)
{ ... }
@@
type TV, TErr, TObj;
identifier OBJ;
identifier VISIT_TYPE =~ "^visit_type_";
@@
void VISIT_TYPE
-(TV v, TObj OBJ, const char *name, TErr errp)
+(TV v, const char *name, TObj OBJ, TErr errp)
{ ... }
// Part 2: swap caller order
@@
expression V, NAME, OBJ, ARG1, ARG2, ERR;
identifier VISIT_TYPE =~ "^visit_type_";
@@
(
-visit_start_struct(V, OBJ, ARG1, NAME, ARG2, ERR)
+visit_start_struct(V, NAME, OBJ, ARG1, ARG2, ERR)
|
-visit_optional(V, ARG1, NAME)
+visit_optional(V, NAME, ARG1)
|
-visit_get_next_type(V, OBJ, ARG1, NAME, ERR)
+visit_get_next_type(V, NAME, OBJ, ARG1, ERR)
|
-visit_type_enum(V, OBJ, ARG1, ARG2, NAME, ERR)
+visit_type_enum(V, NAME, OBJ, ARG1, ARG2, ERR)
|
-VISIT_TYPE(V, OBJ, NAME, ERR)
+VISIT_TYPE(V, NAME, OBJ, ERR)
)
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1454075341-13658-19-git-send-email-eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
After clearing the status register we also have to update the irq line
status. Otherwise a irq which happends to be pending at reset time
causes a interrupt storm. And the guest can't stop as the status
register doesn't indicate any pending interrupt.
Both NetBSD and FreeBSD hang on shutdown because of that.
Cc: qemu-stable@nongnu.org
Reported-by: Andrey Korolyov <andrey@xdel.ru>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1453203884-4125-1-git-send-email-kraxel@redhat.com
While processing isochronous transfer descriptors(iTD), the page
select(PG) field value could lead to an OOB read access. Add
check to avoid it.
Reported-by: Qinghao Tang <luodalongde@gmail.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 1453233406-12165-1-git-send-email-ppandit@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-20-git-send-email-peter.maydell@linaro.org
Done with this Coccinelle semantic patch
@@
expression FMT, E1, E2;
expression list ARGS;
@@
- error_setg(E1, FMT, ARGS, error_get_pretty(E2));
+ error_propagate(E1, E2);/*###*/
+ error_prepend(E1, FMT/*@@@*/, ARGS);
followed by manual cleanup, first because I can't figure out how to
make Coccinelle transform strings, and second to get rid of now
superfluous error_propagate().
We now use or propagate the original error whole instead of just its
message obtained with error_get_pretty(). This avoids suppressing its
hint (see commit 50b7b00), but I can't see how the errors touched in
this commit could come with hints. It also improves the message
printed with &error_abort when we screw up (see commit 1e9b65b).
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Done with this Coccinelle semantic patch
@@
expression FMT, E, S;
expression list ARGS;
@@
- error_report(FMT, ARGS, error_get_pretty(E));
+ error_reportf_err(E, FMT/*@@@*/, ARGS);
(
- error_free(E);
|
exit(S);
|
abort();
)
followed by a replace of '%s"/*@@@*/' by '"' and some line rewrapping,
because I can't figure out how to make Coccinelle transform strings.
We now use the error whole instead of just its message obtained with
error_get_pretty(). This avoids suppressing its hint (see commit
50b7b00), but I can't see how the errors touched in this commit could
come with hints.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1450452927-8346-12-git-send-email-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
On overcommitted CPU, kernel can be so slow that an interrupt can
be triggered by the device whereas the driver is not ready to receive
it. This drives us into an infinite loop.
On suspend, if a SOF interrupt is raised between the stop of the
device processing and the change of the device internal state to
OHCI_USB_SUSPEND (QEMU stops SOF timer on this state change), this
interrupt is never acknowledged.
This patch clears pending SOF interrupt on OHCI_USB_SUSPEND setting.
Some details:
- ohci_irq(): the OHCI interrupt handler, acknowledges the SOF IRQ
only if the state of the driver (rh_state) is OHCI_STATE_RUNNING.
So if this interrupt happens and the driver is not in this state,
the function is called again and again, moving the system to a
CPU starvation.
- ohci_rh_suspend(): the function stop the operation and acknowledge
pending interrupts (but doesn't disable it). Later in the function,
the device is moved to OHCI_SUSPEND_STATE, and the driver to
OHCI_RH_SUSPENDED. If between the moment when the interrupt is
acknowledged and the moment when the device is suspended a new
interrupt is raised, it will be never acknowledged because the
driver is now not in OHCI_RH_RUNNING state.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 1452109525-32150-3-git-send-email-lvivier@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
On overcommitted CPU, kernel can be so slow that an interrupt can
be triggered by the device whereas the driver is not ready to receive
it. This drives us into an infinite loop.
This does not happen on real hardware because real hardware never send
interrupt immediately after the controller has been moved to OPERATION state.
This patch tries to delay the first SOF interrupt to let driver exits from
the critical section (which is not protected against interrupts...)
Some details:
- ohci_irq(): the OHCI interrupt handler, acknowledges the SOF IRQ
only if the state of the driver (rh_state) is OHCI_STATE_RUNNING.
So if this interrupt happens and the driver is not in this state,
the function is called again and again, moving the system to a
CPU starvation.
- ohci_rh_resume(): the driver re-enables operation with OHCI_USB_OPER.
In QEMU this start the SOF timer and QEMU starts to send IRQs. As
the driver is not in OHCI_STATE_RUNNING and not protected against IRQ,
the ohci_irq() can be called and the driver never moved to
OHCI_STATE_RUNNING.
Suggested-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 1452109525-32150-2-git-send-email-lvivier@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
trace_usb_mtp_inotify_event() was being called after the object was
being freed.
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 1450861787-16213-3-git-send-email-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
usb_mtp_inotify_cleanup uses QLIST_FOREACH to pick events
from a list and free them which is incorrect. Use QLIST_FOREACH_SAFE
instead.
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 1450861787-16213-2-git-send-email-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Specification says that: "This bit is set by HCD to initiate a software reset of HC."
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-id: 1450567431-31795-4-git-send-email-hpoussin@reactos.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Specification says that, when entering this state, "the contents of the registers
(except Root Hub registers) are preserved by the HC. [...] The Root Hub is being reset,
which causes the Root Hub's downstream ports to be reset and possibly powered off."
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-id: 1450567431-31795-3-git-send-email-hpoussin@reactos.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Make ehci_process_itd return an error in case we didn't do any actual
iso transfer because we've found no active transaction. That'll avoid
ehci happily run in circles forever if the guest builds a loop out of
idts.
This is CVE-2015-8558.
Cc: qemu-stable@nongnu.org
Reported-by: Qinghao Tang <luodalongde@gmail.com>
Tested-by: P J P <ppandit@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
