smbus.c and smbus.h had device side code, master side code, and
smbus.h has some smbus_eeprom.c definitions. Split them into
separate files.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
When using clang 3.4.2, compilation of QEMU fails like this:
CC aarch64-softmmu/hw/arm/aspeed.o
hw/arm/aspeed.c:36:3: error: redefinition of typedef 'AspeedBoardState' is a C11
feature [-Werror,-Wtypedef-redefinition]
} AspeedBoardState;
^
include/hw/arm/aspeed.h:14:33: note: previous definition is here
typedef struct AspeedBoardState AspeedBoardState;
^
1 error generated.
make[1]: *** [hw/arm/aspeed.o] Error 1
make: *** [subdir-aarch64-softmmu] Error 2
Remove the duplicated typedef to fix this issue.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1543397736-8198-1-git-send-email-thuth@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The code looks better, it removes duplicated lines and it will ease
the introduction of common properties for the Aspeed machines.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180921161939.822-4-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2500 evb is shipped with a W25Q256 which has a non volatile bit
to make the chip operate in 4 Byte address mode at power up. This
should be an interesting feature to model as it will exercise a bit
more the SMC controllers and MMIO execution at boot time.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20180921161939.822-3-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This will be used to construct a memory region beyond the RAM region
to let firmwares scan the address space with load/store to guess how
much RAM the SoC has.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20180807075757.7242-7-joel@jms.id.au
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The pca9552 LED blinkers on the Witherspoon machine are used for leds
but also as GPIOs to control fans and GPUs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180530064049.27976-8-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed boards have at least one EEPROM to hold the Vital Product
Data (VPD).
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20180530064049.27976-6-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2500 EVB does not have an RTC but we can pretend that one is
plugged on the I2C bus header.
The romulus and witherspoon boards expects an Epson RX8900 I2C RTC but
a ds1338 is good enough for the basic features we need.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20180530064049.27976-4-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Witherspoon boards are OpenPOWER system hosting POWER9 Processors.
Add support for their BMC including a couple of I2C devices as found
on real HW.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20180530064049.27976-3-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180530064049.27976-2-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently we use memory_region_init_ram_nomigrate() to create
the "aspeed.boot_rom" memory region, and we don't manually
register it with vmstate_register_ram(). This currently
means that its contents are migrated but as a ram block
whose name is the empty string; in future it may mean they
are not migrated at all. Use memory_region_init_ram() instead.
Note that would be a cross-version migration compatibility break
for the "palmetto-bmc", "ast2500-evb" and "romulus-bmc" machines,
but migration is currently broken for them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20180420124835.7268-3-peter.maydell@linaro.org
The ASPEED hardware contains a lock register for the SCU that disables
any writes to the SCU when it is locked. The machine comes up with the
lock enabled, but on all known hardware u-boot will unlock it and leave
it unlocked when loading the kernel.
This means the kernel expects the SCU to be unlocked. When booting from
an emulated ROM the normal u-boot unlock path is executed. Things don't
go well when booting using the -kernel command line, as u-boot does not
run first.
Change behaviour so that when a kernel is passed to the machine, set the
reset value of the SCU to be unlocked.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20171114122018.12204-1-joel@jms.id.au
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Set the MachineClass flag ignore_memory_transaction_failures
for almost all ARM boards. This means they retain the legacy
behaviour that accesses to unimplemented addresses will RAZ/WI
rather than aborting, when a subsequent commit adds support
for external aborts.
The exceptions are:
* virt -- we know that guests won't try to prod devices
that we don't describe in the device tree or ACPI tables
* mps2 -- this board was written to use unimplemented-device
for all the ranges with devices we don't yet handle
New boards should not set the flag, but instead be written
like the mps2.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1504626814-23124-3-git-send-email-peter.maydell@linaro.org
For the Xilinx boards:
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Rename memory_region_init_rom() to memory_region_init_rom_nomigrate()
and memory_region_init_rom_device() to
memory_region_init_rom_device_nomigrate().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1499438577-7674-5-git-send-email-peter.maydell@linaro.org
This property is an alias for device TYPE_ASPEED_SDMC's property
"ram-size", which is defined with DEFINE_PROP_UINT64().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20170607163635.17635-25-marcandre.lureau@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Temperatures can be changed from the monitor with :
(qemu) qom-set /machine/unattached/device[2] temperature0 12000
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1496739230-32109-3-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Let's add an RTC to the palmetto BMC and a LM75 temperature sensor to
the AST2500 EVB to start with.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1494827476-1487-5-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
The flash devices used for the FMC controller (BMC firmware) are well
defined for each Aspeed machine and are all smaller than the default
mapping window size, at least for CE0 which is the chip the SoC boots
from.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1486648058-520-3-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
write_boot_rom() does not check for negative values. This is more a
problem for coverity than the actual code as the size of the flash
device is checked when the m25p80 object is created. If there is
anything wrong with the backing file, we should not even reach that
path.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1486648058-520-2-git-send-email-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create a ROM region, using the default size of the mapping window for
the CE0 FMC flash module, and fill it with the flash content.
This is a little hacky but until we can boot from a MMIO region, it
seems difficult to do anything else.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1483979087-32663-11-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a new configuration field at the board level and propagate the
value using the "num-cs" property of the FMC controller model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1480434248-27138-14-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The palmetto BMC machine uses a AST2400 revision A1 SoC.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1480434248-27138-11-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Romulus machine is an OpenPOWER system with an AST2500 SoC for
the BMC and a POWER9 chip for the host. It does not make much
difference for qemu a part from the fact that the FMC controller has
two SPI flash module.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 1480434248-27138-8-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Future machine will use different flash models for the FMC and the SPI
controllers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1480434248-27138-7-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2500 SoC has two. Let's prepare ground for the next changes
which will add the required definitions for the second host SPI
controller.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1474977462-28032-4-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed SoC has three different types of SMC (Static Memory
Controller) controllers: the SMC (legacy), the FMC (the new one) and
the SPI for the host PNOR. The FMC and the SPI models are now
converging on the AST2500 SoC and the SMC, which was still available
on the AST2400 SoC, was removed.
The Aspeed SoC does not provide support for the legacy SMC
controller. So, let's rename the 'smc' object to 'fmc' to clarify its
nature.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1474977462-28032-2-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the RAM size is invalid, the memory controller will use a default
value.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1473438177-26079-15-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Configure the size of the RAM of the SOC using a property to propagate
the value down to the memory controller from the board level.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1473438177-26079-14-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1473438177-26079-11-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ast2500 eval board has a hardware strapping register value of
0xF100C2E6 which we use for a definition of AST2500_EVB_HW_STRAP1
below.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1473438177-26079-10-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This gives some explanation behind the magic number 0x120CE416.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1473438177-26079-8-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
aspeed_board_init() now uses a board identifier to customize some values
specific to the board.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1473438177-26079-7-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is mostly a name replacement to prepare ground for other SoCs
specificities. It also adds a TypeInfo struct for the palmetto-bmc
board with a custom initialization for the same reason.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1473438177-26079-6-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We plan to add more Aspeed boards to this file. There are no changes
in the code.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1473438177-26079-5-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
