bdrv_refresh_filename() should invoke itself recursively on all
children, not just on file.
With that change, we can remove the manual invocations in blkverify,
quorum, commit, mirror, and blklogwrites.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Message-id: 20190201192935.18394-3-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
The mirror_start_job() function used for the commit-active job blocks
the source, target and all intermediate nodes for the duration of the
job.
target <- intermediate <- source
Since 4ef85a9c23 this function creates a dummy mirror_top_bs that
goes on top of the source node, and it is this dummy node that gets
blocked instead. The source node is never blocked or added to the
job's list of nodes.
target <- intermediate <- source <- mirror_top
At the moment I don't think it is possible to exploit this problem
because any additional job on 'source' would either be forbidden for
other reasons or it would need to involve an additional node that is
blocked, causing an error.
This can be seen in the error messages, however, because they never
refer to the source node being blocked:
$ qemu-img create -f qcow2 hd0.qcow2 1M
$ qemu-img create -f qcow2 -b hd0.qcow2 hd1.qcow2
$ qemu-io -c 'write 0 1M' hd0.qcow2
$ $QEMU -drive if=none,file=hd1.qcow2,node-name=hd1
{ "execute": "qmp_capabilities" }
{ "execute": "block-commit", "arguments": {"device": "hd1", "speed": 256}}
{ "execute": "block-stream", "arguments": {"device": "hd1"}}
{ "error": {"class": "GenericError",
"desc": "Node 'hd0' is busy: block device is in use by block job: commit"}}
After this patch the error message refers to 'hd1', as it should.
The expected output of iotest 141 also needs to be updated for the
same reason.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
At the moment I don't see how to make this function fail after the
dirty bitmap has been created, but if that was possible then we would
hit the assert(QLIST_EMPTY(&bs->dirty_bitmaps)) in bdrv_close().
Signed-off-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Use bdrv_dirty_bitmap_next_dirty_area() instead of
bdrv_dirty_iter_next_area(), because of the following problems of
bdrv_dirty_iter_next_area():
1. Using HBitmap iterators we should carefully handle unaligned offset,
as first call to hbitmap_iter_next() may return a value less than
original offset (actually, it will be original offset rounded down to
bitmap granularity). This handling is not done in
do_sync_target_write().
2. bdrv_dirty_iter_next_area() handles unaligned max_offset
incorrectly:
look at the code:
if (max_offset == iter->bitmap->size) {
/* If max_offset points to the image end, round it up by the
* bitmap granularity */
gran_max_offset = ROUND_UP(max_offset, granularity);
} else {
gran_max_offset = max_offset;
}
ret = hbitmap_iter_next(&iter->hbi, false);
if (ret < 0 || ret + granularity > gran_max_offset) {
return false;
}
and assume that max_offset != iter->bitmap->size but still unaligned.
if 0 < ret < max_offset we found dirty area, but the function can
return false in this case (if ret + granularity > max_offset).
3. bdrv_dirty_iter_next_area() uses inefficient loop to find the end of
the dirty area. Let's use more efficient hbitmap_next_zero instead
(bdrv_dirty_bitmap_next_dirty_area() do so)
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Most list head structs need not be given a name. In most cases the
name is given just in case one is going to use QTAILQ_LAST, QTAILQ_PREV
or reverse iteration, but this does not apply to lists of other kinds,
and even for QTAILQ in practice this is only rarely needed. In addition,
we will soon reimplement those macros completely so that they do not
need a name for the head struct. So clean up everything, not giving a
name except in the rare case where it is necessary.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Marking a function coroutine_fn currently has no effect on the compiler,
but it documents that this function must be called from coroutine
context and it may yield. This is important information for the
programmer.
Also, if we ever transition to a stackless coroutine implementation,
then it's likely that the annotation will become mandatory so the
compiler can use the correct calling convention for coroutine functions.
Cc: Max Reitz <mreitz@redhat.com>
Cc: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The 'block-commit' QMP command is implemented internally using two
different drivers. If the source image is the active layer then the
mirror driver is used (commit_active_start()), otherwise the commit
driver is used (commit_start()).
In both cases the destination image must be put temporarily in
read-write mode. This is done correctly in the latter case, but what
commit_active_start() does is copy all flags instead.
This patch replaces the bdrv_reopen() calls in that function with
bdrv_reopen_set_read_only() so that only the read-only status is
changed.
A similar change is made in mirror_exit(), which is also used by the
'drive-mirror' and 'blockdev-mirror' commands.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Let start from the beginning:
Commit b9e413dd37 (in 2.9)
"block: explicitly acquire aiocontext in aio callbacks that need it"
added pairs of aio_context_acquire/release to mirror_write_complete and
mirror_read_complete, when they were aio callbacks for blk_aio_* calls.
Then, commit 2e1990b26e (in 3.0) "block/mirror: Convert to coroutines"
dropped these blk_aio_* calls, than mirror_write_complete and
mirror_read_complete are not callbacks more, and don't need additional
aiocontext acquiring. Furthermore, mirror_read_complete calls
blk_co_pwritev inside these pair of aio_context_acquire/release, which
leads to the following dead-lock with mirror:
(gdb) info thr
Id Target Id Frame
3 Thread (LWP 145412) "qemu-system-x86" syscall ()
2 Thread (LWP 145416) "qemu-system-x86" __lll_lock_wait ()
* 1 Thread (LWP 145411) "qemu-system-x86" __lll_lock_wait ()
(gdb) bt
#0 __lll_lock_wait ()
#1 _L_lock_812 ()
#2 __GI___pthread_mutex_lock
#3 qemu_mutex_lock_impl (mutex=0x561032dce420 <qemu_global_mutex>,
file=0x5610327d8654 "util/main-loop.c", line=236) at
util/qemu-thread-posix.c:66
#4 qemu_mutex_lock_iothread_impl
#5 os_host_main_loop_wait (timeout=480116000) at util/main-loop.c:236
#6 main_loop_wait (nonblocking=0) at util/main-loop.c:497
#7 main_loop () at vl.c:1892
#8 main
Printing contents of qemu_global_mutex, I see that "__owner = 145416",
so, thr1 is main loop, and now it wants BQL, which is owned by thr2.
(gdb) thr 2
(gdb) bt
#0 __lll_lock_wait ()
#1 _L_lock_870 ()
#2 __GI___pthread_mutex_lock
#3 qemu_mutex_lock_impl (mutex=0x561034d25dc0, ...
#4 aio_context_acquire (ctx=0x561034d25d60)
#5 dma_blk_cb
#6 dma_blk_io
#7 dma_blk_read
#8 ide_dma_cb
#9 bmdma_cmd_writeb
#10 bmdma_write
#11 memory_region_write_accessor
#12 access_with_adjusted_size
#15 flatview_write
#16 address_space_write
#17 address_space_rw
#18 kvm_handle_io
#19 kvm_cpu_exec
#20 qemu_kvm_cpu_thread_fn
#21 qemu_thread_start
#22 start_thread
#23 clone ()
Printing mutex in fr 2, I see "__owner = 145411", so thr2 wants aio
context mutex, which is owned by thr1. Classic dead-lock.
Then, let's check that aio context is hold by mirror coroutine: just
print coroutine stack of first tracked request in mirror job target:
(gdb) [...]
(gdb) qemu coroutine 0x561035dd0860
#0 qemu_coroutine_switch
#1 qemu_coroutine_yield
#2 qemu_co_mutex_lock_slowpath
#3 qemu_co_mutex_lock
#4 qcow2_co_pwritev
#5 bdrv_driver_pwritev
#6 bdrv_aligned_pwritev
#7 bdrv_co_pwritev
#8 blk_co_pwritev
#9 mirror_read_complete () at block/mirror.c:232
#10 mirror_co_read () at block/mirror.c:370
#11 coroutine_trampoline
#12 __start_context
Yes it is mirror_read_complete calling blk_co_pwritev after acquiring
aio context.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
For purposes of minimum code movement, refactor the mirror_exit
callback to use the post-finalization callbacks in a trivial way.
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 20180906130225.5118-7-jsnow@redhat.com
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
[mreitz: Added comment for the mirror_exit() function]
Signed-off-by: Max Reitz <mreitz@redhat.com>
In cases where we abort the block/mirror job, there's no point in
installing the new backing chain before we finish aborting.
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 20180906130225.5118-6-jsnow@redhat.com
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Add support for taking and passing forward job creation flags.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Message-id: 20180906130225.5118-3-jsnow@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Change the manual deferment to mirror_exit into the implicit
callback to job_exit and the mirror_exit callback.
This does change the order of some bdrv_unref calls and job_completed,
but thanks to the new context in which we call .exit, this is safe to
defer the possible flushing of any nodes to the job_finalize_single
cleanup stage.
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 20180830015734.19765-6-jsnow@redhat.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Jobs presently use both an Error object in the case of the create job,
and char strings in the case of generic errors elsewhere.
Unify the two paths as just j->err, and remove the extra argument from
job_completed. The integer error code for job_completed is kept for now,
to be removed shortly in a separate patch.
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 20180830015734.19765-3-jsnow@redhat.com
[mreitz: Dropped a superfluous g_strdup()]
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Presently we codify the entry point for a job as the "start" callback,
but a more apt name would be "run" to clarify the idea that when this
function returns we consider the job to have "finished," except for
any cleanup which occurs in separate callbacks later.
As part of this clarification, change the signature to include an error
object and a return code. The error ptr is not yet used, and the return
code while captured, will be overwritten by actions in the job_completed
function.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20180830015734.19765-2-jsnow@redhat.com
Reviewed-by: Jeff Cody <jcody@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
.bdrv_close handler is optional after previous commit, no needs to keep
empty functions more.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
blockdev-mirror with the same node for source and target segfaults
today: A node is in its own backing chain, so mirror_start_job() decides
that this is an active commit. When adding the intermediate nodes with
block_job_add_bdrv(), it starts the iteration through the subchain with
the backing file of source, though, so it never reaches target and
instead runs into NULL at the base.
While we could fix that by starting with source itself, there is no
point in allowing mirroring a node into itself and I wouldn't be
surprised if this caused more problems later.
So just check for this scenario and error out.
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Other I/O functions are already using a BdrvChild pointer in the API, so
make discard do the same. It makes it possible to initiate the same
permission checks before doing I/O, and much easier to share the
helper functions for this, which will be added and used by write,
truncate and copy range paths.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch allows the user to specify whether to use active or only
background mode for mirror block jobs. Currently, this setting will
remain constant for the duration of the entire block job.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Message-id: 20180613181823.13618-14-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
This patch implements active synchronous mirroring. In active mode, the
passive mechanism will still be in place and is used to copy all
initially dirty clusters off the source disk; but every write request
will write data both to the source and the target disk, so the source
cannot be dirtied faster than data is mirrored to the target. Also,
once the block job has converged (BLOCK_JOB_READY sent), source and
target are guaranteed to stay in sync (unless an error occurs).
Active mode is completely optional and currently disabled at runtime. A
later patch will add a way for users to enable it.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 20180613181823.13618-13-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
This will allow us to access the block job data when the mirror block
driver becomes more complex.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 20180613181823.13618-11-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
With this, the mirror_top_bs is no longer just a technically required
node in the BDS graph but actually represents the block job operation.
Also, drop MirrorBlockJob.source, as we can reach it through
mirror_top_bs->backing.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Message-id: 20180613181823.13618-6-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
This patch makes the mirror code differentiate between simply waiting
for any operation to complete (mirror_wait_for_free_in_flight_slot())
and specifically waiting for all operations touching a certain range of
the virtual disk to complete (mirror_wait_on_conflicts()).
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 20180613181823.13618-5-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Attach a CoQueue to each in-flight operation so if we need to wait for
any we can use it to wait instead of just blindly yielding and hoping
for some operation to wake us.
A later patch will use this infrastructure to allow requests accessing
the same area of the virtual disk to specifically wait for each other.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 20180613181823.13618-4-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
In order to talk to the source BDS (and maybe in the future to the
target BDS as well) directly, we need to convert our existing AIO
requests into coroutine I/O requests.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 20180613181823.13618-3-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
When converting mirror's I/O to coroutines, we are going to need a point
where these coroutines are created. mirror_perform() is going to be
that point.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Message-id: 20180613181823.13618-2-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
We already requested that block jobs be paused in .bdrv_drained_begin,
but no guarantee was made that the job was actually inactive at the
point where bdrv_drained_begin() returned.
This introduces a new callback BdrvChildRole.bdrv_drained_poll() and
uses it to make bdrv_drain_poll() consider block jobs using the node to
be drained.
For the test case to work as expected, we have to switch from
block_job_sleep_ns() to qemu_co_sleep_ns() so that the test job is even
considered active and must be waited for when draining the node.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
So far we relied on job->ret and strerror() to produce an error message
for failed jobs. Not surprisingly, this tends to result in completely
useless messages.
This adds a Job.error field that can contain an error string for a
failing job, and a parameter to job_completed() that sets the field. As
a default, if NULL is passed, we continue to use strerror(job->ret).
All existing callers are changed to pass NULL. They can be improved in
separate patches.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
BlockJob has fields .offset and .len, which are actually misnomers today
because they are no longer tied to block device sizes, but just progress
counters. As such they make a lot of sense in generic Jobs.
This patch moves the fields to Job and renames them to .progress_current
and .progress_total to describe their function better.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
The transition to the READY state was still performed in the BlockJob
layer, in the same function that sent the BLOCK_JOB_READY QMP event.
This patch brings the state transition to the Job layer and implements
the QMP event using a notifier called from the Job layer, like we
already do for other events related to state transitions.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
This moves the .complete callback that tells a READY job to complete
from BlockJobDriver to JobDriver. The wrapper function job_complete()
doesn't require anything block job specific any more and can be moved
to Job.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
block_job_drain() contains a blk_drain() call which cannot be moved to
Job, so add a new JobDriver callback JobDriver.drain which has a common
implementation for all BlockJobs. In addition to this we keep the
existing BlockJobDriver.drain callback that is called by the common
drain implementation for all block jobs.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
block_job_cancel_async() did two things that were still block job
specific:
* Setting job->force. This field makes sense on the Job level, so we can
just move it. While at it, rename it to job->force_cancel to make its
purpose more obvious.
* Resetting the I/O status. This can't be moved because generic Jobs
don't have an I/O status. What the function really implements is a
user resume, except without entering the coroutine. Consequently, it
makes sense to call the .user_resume driver callback here which
already resets the I/O status.
The old block_job_cancel_async() has two separate if statements that
check job->iostatus != BLOCK_DEVICE_IO_STATUS_OK and job->user_paused.
However, the former condition always implies the latter (as is
asserted in block_job_iostatus_reset()), so changing the explicit call
of block_job_iostatus_reset() on the former condition with the
.user_resume callback on the latter condition is equivalent and
doesn't need to access any BlockJob specific state.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
This moves the finalisation of a single job from BlockJob to Job.
Some part of this code depends on job transactions, and job transactions
call this code, we introduce some temporary calls from Job functions to
BlockJob ones. This will be fixed once transactions move to Job, too.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
This renames the BlockJobCreateFlags constants, moves a few JOB_INTERNAL
checks to job_create() and the auto_{finalize,dismiss} fields from
BlockJob to Job.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
While we already moved the state related to job pausing to Job, the
functions to do were still BlockJob only. This commit moves them over to
Job.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
There is nothing block layer specific about block_job_sleep_ns(), so
move the function to Job.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
This commit moves some core functions for dealing with the job coroutine
from BlockJob to Job. This includes primarily entering the coroutine
(both for the first and reentering) and yielding explicitly and at pause
points.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Move the defer_to_main_loop functionality from BlockJob to Job.
The code can be simplified because we can use job->aio_context in
job_defer_to_main_loop_bh() now, instead of having to access the
BlockDriverState.
Probably taking the data->aio_context lock in addition was already
unnecessary in the old code because we didn't actually make use of
anything protected by the old AioContext except getting the new
AioContext, in case it changed between scheduling the BH and running it.
But it's certainly unnecessary now that the BDS isn't accessed at all
any more.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
We cannot yet move the whole logic around job cancelling to Job because
it depends on quite a few other things that are still only in BlockJob,
but we can move the cancelled field at least.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
This moves reference counting from BlockJob to Job.
In order to keep calling the BlockJob cleanup code when the job is
deleted via job_unref(), introduce a new JobDriver.free callback. Every
block job must use block_job_free() for this callback, this is asserted
in block_job_create().
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
This moves the job_type field from BlockJobDriver to JobDriver.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
QAPI types aren't externally visible, so we can rename them without
causing problems. Before we add a job type to Job, rename the enum
so it can be used for more than just block jobs.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
This is the first step towards creating an infrastructure for generic
background jobs that aren't tied to a block device. For now, Job only
stores its ID and JobDriver, the rest stays in BlockJob.
The following patches will move over more parts of BlockJob to Job if
they are meaningful outside the context of a block job.
BlockJob.driver is now redundant, but this patch leaves it around to
avoid unnecessary churn. The next patches will get rid of almost all of
its uses anyway so that it can be removed later with much less churn.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Update the rest of the filter drivers to support
BDRV_REQ_WRITE_UNCHANGED. They already forward write request flags to
their children, so we just have to announce support for it.
This patch does not cover the replication driver because that currently
does not support flags at all, and because it just grabs the WRITE
permission for its children when it can, so we should be fine just
submitting the incoming WRITE_UNCHANGED requests as normal writes.
It also does not cover format drivers for similar reasons. They all use
bdrv_format_default_perms() as their .bdrv_child_perm() implementation
so they just always grab the WRITE permission for their file children
whenever possible. In addition, it often would be difficult to
ascertain whether incoming unchanging writes end up as unchanging writes
in their files. So we just leave them as normal potentially changing
writes.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Message-id: 20180421132929.21610-7-mreitz@redhat.com
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
This gets us rid of more direct accesses to BlockJob fields from the
job drivers.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
All block job drivers support .set_speed and all of them duplicate the
same code to implement it. Move that code to blockjob.c and remove the
now useless callback.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Every block job has a RateLimit, and they all do the exact same thing
with it, so it should be common infrastructure. Move the struct field
for a start.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Block job drivers are not expected to mess with the internals of the
BlockJob object, so provide wrapper functions for one of the cases where
they still do it: Updating the progress counter.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
