The new PAPR 2.12 defines a watchdog facility managed via the new
H_WATCHDOG hypercall.
This adds H_WATCHDOG support which a proposed driver for pseries uses:
https://patchwork.ozlabs.org/project/linuxppc-dev/list/?series=303120
This was tested by running QEMU with a debug kernel and command line:
-append \
"pseries-wdt.timeout=60 pseries-wdt.nowayout=1 pseries-wdt.action=2"
and running "echo V > /dev/watchdog0" inside the VM.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220622051008.1067464-1-aik@ozlabs.ru>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
AST1030 wdt controller is similiar to AST2600's wdt, but it has extra
registers.
Introduce ast1030 object class and increse the number of regs(offset) of
ast1030 model.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220401083850.15266-5-jamin_lin@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Per ast2500_2520_datasheet_v1.8 and ast2600v11.pdf, the default value of
WDT00 and WDT04 is 0x014FB180 for ast2500/ast2600.
Add default_status and default_reload_value attributes for storing
counter status and reload value as they are different from ast2400.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220401083850.15266-4-jamin_lin@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Instead of invoking select_watchdog_action from both HMP and command line,
go directly from HMP to QMP and use QemuOpts as the intermediary for the
command line.
This makes -watchdog-action explicitly a shortcut for "-action watchdog",
so that "-watchdog-action" and "-action watchdog" override each other
based on the position on the command line; previously, "-action watchdog"
always won.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The logic in the handling for the control register required toggling the
enable state for writes to stick. Rework the condition chain to allow
sequential writes that do not update the enable state.
Fixes: 854123bf8d ("wdt: Add Aspeed watchdog device model")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210709053107.1829304-3-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
While some of the critical fields remain the same, there is variation in
the definition of the control register across the SoC generations.
Reserved regions are adjusted, while in other cases the mutability or
behaviour of fields change.
Introduce a callback to sanitize the value on writes to ensure model
behaviour reflects the hardware.
Fixes: 854123bf8d ("wdt: Add Aspeed watchdog device model")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210709053107.1829304-2-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Commit e50caf4a5c ("tracing: convert documentation to rST")
converted docs/devel/tracing.txt to docs/devel/tracing.rst.
We still have several references to the old file, so let's fix them
with the following command:
sed -i s/tracing.txt/tracing.rst/ $(git grep -l docs/devel/tracing.txt)
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210517151702.109066-2-sgarzare@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The Clock framework allows users to specify a callback which is
called after the clock's period has been updated. Some users need to
also have a callback which is called before the clock period is
updated.
As the first step in adding support for notifying Clock users on
pre-update events, add an argument to the ClockCallback to specify
what event is being notified, and add an argument to the various
functions for registering a callback to specify which events are
of interest to that callback.
Note that the documentation update renders correct the previously
incorrect claim in 'Adding a new clock' that callbacks "will be
explained in a following section".
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-2-peter.maydell@linaro.org
Now no users are setting the frq properties on the CMSDK timer,
dualtimer, watchdog or ARMSSE SoC devices, we can remove the
properties and the struct fields that back them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-25-peter.maydell@linaro.org
Message-id: 20210121190622.22000-25-peter.maydell@linaro.org
Switch the CMSDK APB watchdog device over to using its Clock input;
the wdogclk_frq property is now ignored.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-21-peter.maydell@linaro.org
Message-id: 20210121190622.22000-21-peter.maydell@linaro.org
As the first step in converting the CMSDK_APB_TIMER device to the
Clock framework, add a Clock input. For the moment we do nothing
with this clock; we will change the behaviour from using the
wdogclk-frq property to using the Clock once all the users of this
device have been converted to wire up the Clock.
This is a migration compatibility break for machines mps2-an385,
mps2-an386, mps2-an500, mps2-an511, mps2-an505, mps2-an521, musca-a,
musca-b1, lm3s811evb, lm3s6965evb.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-10-peter.maydell@linaro.org
Message-id: 20210121190622.22000-10-peter.maydell@linaro.org
This commit is the result of running the timer-del-timer-free.cocci
script on the whole source tree.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201215154107.3255-4-peter.maydell@linaro.org
Neither sysbus.h nor module.h are required to compile this file.
diag288 is not a sysbus device, and module.h (for type_init) is
included eventually through qom/object.h.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <20201118090344.243117-1-thuth@redhat.com>
[CH: tweaked description]
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Generic watchdog device model implementation as per ARM SBSA v6.0
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Message-id: 20201027015927.29495-2-shashi.mallela@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Meson doesn't enjoy the same flexibility we have with Make in choosing
the include path. In particular the tracing headers are using
$(build_root)/$(<D).
In order to keep the include directives unchanged,
the simplest solution is to generate headers with patterns like
"trace/trace-audio.h" and place forwarding headers in the source tree
such that for example "audio/trace.h" includes "trace/trace-audio.h".
This patch is too ugly to be applied to the Makefiles now. It's only
a way to separate the changes to the tracing header files from the
Meson rewrite of the tracing logic.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a trace event to see when a guest disable/enable the watchdog.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200617072539.32686-2-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement full support for the watchdog in i.MX systems.
Pretimeout support is optional because the watchdog hardware
on i.MX31 does not support pretimeouts.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20200517162135.110364-3-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: added Property array terminator entry]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
In preparation for a full implementation, move i.MX watchdog driver
from hw/misc to hw/watchdog. While at it, add the watchdog files
to MAINTAINERS.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20200517162135.110364-2-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Devices may have component devices and buses.
Device realization may fail. Realization is recursive: a device's
realize() method realizes its components, and device_set_realized()
realizes its buses (which should in turn realize the devices on that
bus, except bus_set_realized() doesn't implement that, yet).
When realization of a component or bus fails, we need to roll back:
unrealize everything we realized so far. If any of these unrealizes
failed, the device would be left in an inconsistent state. Must not
happen.
device_set_realized() lets it happen: it ignores errors in the roll
back code starting at label child_realize_fail.
Since realization is recursive, unrealization must be recursive, too.
But how could a partly failed unrealize be rolled back? We'd have to
re-realize, which can fail. This design is fundamentally broken.
device_set_realized() does not roll back at all. Instead, it keeps
unrealizing, ignoring further errors.
It can screw up even for a device with no buses: if the lone
dc->unrealize() fails, it still unregisters vmstate, and calls
listeners' unrealize() callback.
bus_set_realized() does not roll back either. Instead, it stops
unrealizing.
Fortunately, no unrealize method can fail, as we'll see below.
To fix the design error, drop parameter @errp from all the unrealize
methods.
Any unrealize method that uses @errp now needs an update. This leads
us to unrealize() methods that can fail. Merely passing it to another
unrealize method cannot cause failure, though. Here are the ones that
do other things with @errp:
* virtio_serial_device_unrealize()
Fails when qbus_set_hotplug_handler() fails, but still does all the
other work. On failure, the device would stay realized with its
resources completely gone. Oops. Can't happen, because
qbus_set_hotplug_handler() can't actually fail here. Pass
&error_abort to qbus_set_hotplug_handler() instead.
* hw/ppc/spapr_drc.c's unrealize()
Fails when object_property_del() fails, but all the other work is
already done. On failure, the device would stay realized with its
vmstate registration gone. Oops. Can't happen, because
object_property_del() can't actually fail here. Pass &error_abort
to object_property_del() instead.
* spapr_phb_unrealize()
Fails and bails out when remove_drcs() fails, but other work is
already done. On failure, the device would stay realized with some
of its resources gone. Oops. remove_drcs() fails only when
chassis_from_bus()'s object_property_get_uint() fails, and it can't
here. Pass &error_abort to remove_drcs() instead.
Therefore, no unrealize method can fail before this patch.
device_set_realized()'s recursive unrealization via bus uses
object_property_set_bool(). Can't drop @errp there, so pass
&error_abort.
We similarly unrealize with object_property_set_bool() elsewhere,
always ignoring errors. Pass &error_abort instead.
Several unrealize methods no longer handle errors from other unrealize
methods: virtio_9p_device_unrealize(),
virtio_input_device_unrealize(), scsi_qdev_unrealize(), ...
Much of the deleted error handling looks wrong anyway.
One unrealize methods no longer ignore such errors:
usb_ehci_pci_exit().
Several realize methods no longer ignore errors when rolling back:
v9fs_device_realize_common(), pci_qdev_unrealize(),
spapr_phb_realize(), usb_qdev_realize(), vfio_ccw_realize(),
virtio_device_realize().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-17-armbru@redhat.com>
The Aspeed Watchdog and Timer models have a link pointing to the SCU
controller model of the machine.
Change the "scu" property definition so that it explicitly sets the
pointer. The property isn't optional : not being able to set the link
is a bug and QEMU should rather abort than exit in this case.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-17-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2600 control register sneakily changed the meaning of bit 4
without anyone noticing. It no longer controls the 1MHz vs APB clock
select, and instead always runs at 1MHz.
The AST2500 was always 1MHz too, but it retained bit 4, making it read
only. We can model both using the same fixed 1MHz calculation.
Fixes: 6b2b2a703c ("hw: wdt_aspeed: Add AST2600 support")
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-10-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Users benefit from knowing which watchdog timer has expired. The address
of the watchdog's registers unambiguously indicates which has expired,
so log that.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-9-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2600 has four watchdogs, and they each have a 0x40 of registers.
When running as part of an ast2600 system we must check a different
offset for the system reset control register in the SCU.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190925143248.10000-12-clg@kaod.org
[clg: - reworked model integration into new object class ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It cleanups the current models for the Aspeed AST2400 and AST2500 SoCs
and prepares ground for future SoCs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-11-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When WDT_RESTART is written, the data is not the contents
of the WDT_CTRL register. Hence ensure we are looking at
WDT_CTRL to check if bit WDT_CTRL_1MHZ_CLK is set or not.
Signed-off-by: Amithash Prasad <amithash@fb.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190925143248.10000-2-clg@kaod.org
[clg: improved Suject prefix ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Switch the cmsdk-apb-watchdog code away from bottom-half based
ptimers to the new transaction-based ptimer API. This just requires
adding begin/commit calls around the various places that modify the
ptimer state, and using the new ptimer_init() function to create the
timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-21-peter.maydell@linaro.org
Currently the ptimer design uses a QEMU bottom-half as its
mechanism for calling back into the device model using the
ptimer when the timer has expired. Unfortunately this design
is fatally flawed, because it means that there is a lag
between the ptimer updating its own state and the device
callback function updating device state, and guest accesses
to device registers between the two can return inconsistent
device state.
We want to replace the bottom-half design with one where
the guest device's callback is called either immediately
(when the ptimer triggers by timeout) or when the device
model code closes a transaction-begin/end section (when the
ptimer triggers because the device model changed the
ptimer's count value or other state). As the first step,
rename ptimer_init() to ptimer_init_with_bh(), to free up
the ptimer_init() name for the new API. We can then convert
all the ptimer users away from ptimer_init_with_bh() before
removing it entirely.
(Commit created with
git grep -l ptimer_init | xargs sed -i -e 's/ptimer_init/ptimer_init_with_bh/'
and three overlong lines folded by hand.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-2-peter.maydell@linaro.org
sysemu/sysemu.h is a rather unfocused dumping ground for stuff related
to the system-emulator. Evidence:
* It's included widely: in my "build everything" tree, changing
sysemu/sysemu.h still triggers a recompile of some 1100 out of 6600
objects (not counting tests and objects that don't depend on
qemu/osdep.h, down from 5400 due to the previous two commits).
* It pulls in more than a dozen additional headers.
Split stuff related to run state management into its own header
sysemu/runstate.h.
Touching sysemu/sysemu.h now recompiles some 850 objects. qemu/uuid.h
also drops from 1100 to 850, and qapi/qapi-types-run-state.h from 4400
to 4200. Touching new sysemu/runstate.h recompiles some 500 objects.
Since I'm touching MAINTAINERS to add sysemu/runstate.h anyway, also
add qemu/main-loop.h.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-30-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
[Unbreak OS-X build]
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
In my "build everything" tree, changing hw/hw.h triggers a recompile
of some 2600 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
The previous commits have left only the declaration of hw_error() in
hw/hw.h. This permits dropping most of its inclusions. Touching it
now recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-19-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/irq.h triggers a recompile
of some 5400 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get qemu_irq and.or qemu_irq_handler.
Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed. Touching it now recompiles only some 500 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-13-armbru@redhat.com>
In my "build everything" tree, changing sysemu/reset.h triggers a
recompile of some 2600 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
The main culprit is hw/hw.h, which supposedly includes it for
convenience.
Include sysemu/reset.h only where it's needed. Touching it now
recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-9-armbru@redhat.com>
The ast2500 uses the watchdog to reset the SDRAM controller. This
operation is usually performed by u-boot's memory training procedure,
and it is enabled by setting a bit in the SCU and then causing the
watchdog to expire. Therefore, we need the watchdog to be able to
access the SCU's register space.
This causes the watchdog to not perform a system reset when the bit is
set. In the future it could perform a reset of the SDMC model.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190621065242.32535-1-joel@jms.id.au
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Rather than looking inside the definition of a DeviceState with
"s->qdev", use the QOM prefered style: "DEVICE(s)".
This patch was generated using the following Coccinelle script:
// Use DEVICE() macros to access DeviceState.qdev
@use_device_macro_to_access_qdev@
expression obj;
identifier dev;
@@
-&obj->dev.qdev
+DEVICE(obj)
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20190528164020.32250-11-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Some trace points are attributed to the wrong source file. Happens
when we neglect to update trace-events for code motion, or add events
in the wrong place, or misspell the file name.
Clean up with help of cleanup-trace-events.pl. Same funnies as in the
previous commit, of course. Manually shorten its change to
linux-user/trace-events to */signal.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-id: 20190314180929.27722-6-armbru@redhat.com
Message-Id: <20190314180929.27722-6-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We spell out sub/dir/ in sub/dir/trace-events' comments pointing to
source files. That's because when trace-events got split up, the
comments were moved verbatim.
Delete the sub/dir/ part from these comments. Gets rid of several
misspellings.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190314180929.27722-3-armbru@redhat.com
Message-Id: <20190314180929.27722-3-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-39-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-36-yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of including the same list of devices for each target,
set CONFIG_PCI to true, and make the devices default to present
whenever PCI is available. However, s390x does not want all the
PCI devices, so there is a separate symbol to enable them.
Done mostly with the following script:
while read i; do
i=${i%=y}; i=${i#CONFIG_}
sed -i -e'/^config '$i'$/!b' -en \
-e'a\' -e' default y if PCI_DEVICES\' -e' depends on PCI' \
`grep -lw $i hw/*/Kconfig`
done < default-configs/pci.mak
followed by replacing a few "depends on" clauses with "select"
whenever the symbol is not really related to PCI.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-31-yang.zhong@intel.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Kconfig files were generated mostly with this script:
for i in `grep -ho CONFIG_[A-Z0-9_]* default-configs/* | sort -u`; do
set fnord `git grep -lw $i -- 'hw/*/Makefile.objs' `
shift
if test $# = 1; then
cat >> $(dirname $1)/Kconfig << EOF
config ${i#CONFIG_}
bool
EOF
git add $(dirname $1)/Kconfig
else
echo $i $*
fi
done
sed -i '$d' hw/*/Kconfig
for i in hw/*; do
if test -d $i && ! test -f $i/Kconfig; then
touch $i/Kconfig
git add $i/Kconfig
fi
done
Whenever a symbol is referenced from multiple subdirectories, the
script prints the list of directories that reference the symbol.
These symbols have to be added manually to the Kconfig files.
Kconfig.host and hw/Kconfig were created manually.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-27-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Implement the watchdog timer for the stellaris boards.
This device is a close variant of the CMSDK APB watchdog
device, so we can model it by subclassing that device and
tweaking the behaviour of some of its registers.
Signed-off-by: Michel Heily <michelheily@gmail.com>
Reviewed-by: Peter Maydell <petser.maydell@linaro.org>
[PMM: rewrote commit message, fixed a few checkpatch nits,
added comment giving the URL of the spec for the Stellaris
variant of the watchdog device]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
