The TMP105 datasheet says that in Interrupt Mode (when TM==1) the device
signals an alert when the temperature equals or exceeds the T_high value and
then remains high until a device register is read or the device responds to
the SMBUS Alert Response address, or the device is put into Shutdown Mode.
Thereafter the Alert pin will only be re-signalled when temperature falls
below T_low; alert can then be cleared in the same set of ways, and the
device returns to its initial "alert when temperature goes above T_high"
mode. (If this textual description is confusing, see figure 3 in the
TI datasheet at https://www.ti.com/lit/gpn/tmp105 .)
We were misimplementing this as a simple "always alert if temperature is
above T_high or below T_low" condition, which gives a spurious alert on
startup if using the "T_high = 80 degrees C, T_low = 75 degrees C" reset
limit values.
Implement the correct (hysteresis) behaviour by tracking whether we
are currently looking for the temperature to rise over T_high or
for it to fall below T_low. Our implementation of the comparator
mode (TM==0) wasn't wrong, but rephrase it to match the way that
interrupt mode is now handled for clarity.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20201110150023.25533-3-peter.maydell@linaro.org
The TMP105 datasheet (https://www.ti.com/lit/gpn/tmp105) says that the
power-up reset values for the T_low and T_high registers are 80 degrees C
and 75 degrees C, which are 0x500 and 0x4B0 hex according to table 5. These
values are then shifted right by four bits to give the register reset
values, since both registers store the 12 bits of temperature data in bits
[15..4] of a 16 bit register.
We were resetting these registers to zero, which is problematic for Linux
guests which enable the alert interrupt and then immediately take an
unexpected overtemperature alert because the current temperature is above
freezing...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20201110150023.25533-2-peter.maydell@linaro.org
When all we do with an Error we receive into a local variable is
propagating to somewhere else, we can just as well receive it there
right away. Convert
if (!foo(..., &err)) {
...
error_propagate(errp, err);
...
return ...
}
to
if (!foo(..., errp)) {
...
...
return ...
}
where nothing else needs @err. Coccinelle script:
@rule1 forall@
identifier fun, err, errp, lbl;
expression list args, args2;
binary operator op;
constant c1, c2;
symbol false;
@@
if (
(
- fun(args, &err, args2)
+ fun(args, errp, args2)
|
- !fun(args, &err, args2)
+ !fun(args, errp, args2)
|
- fun(args, &err, args2) op c1
+ fun(args, errp, args2) op c1
)
)
{
... when != err
when != lbl:
when strict
- error_propagate(errp, err);
... when != err
(
return;
|
return c2;
|
return false;
)
}
@rule2 forall@
identifier fun, err, errp, lbl;
expression list args, args2;
expression var;
binary operator op;
constant c1, c2;
symbol false;
@@
- var = fun(args, &err, args2);
+ var = fun(args, errp, args2);
... when != err
if (
(
var
|
!var
|
var op c1
)
)
{
... when != err
when != lbl:
when strict
- error_propagate(errp, err);
... when != err
(
return;
|
return c2;
|
return false;
|
return var;
)
}
@depends on rule1 || rule2@
identifier err;
@@
- Error *err = NULL;
... when != err
Not exactly elegant, I'm afraid.
The "when != lbl:" is necessary to avoid transforming
if (fun(args, &err)) {
goto out
}
...
out:
error_propagate(errp, err);
even though other paths to label out still need the error_propagate().
For an actual example, see sclp_realize().
Without the "when strict", Coccinelle transforms vfio_msix_setup(),
incorrectly. I don't know what exactly "when strict" does, only that
it helps here.
The match of return is narrower than what I want, but I can't figure
out how to express "return where the operand doesn't use @err". For
an example where it's too narrow, see vfio_intx_enable().
Silently fails to convert hw/arm/armsse.c, because Coccinelle gets
confused by ARMSSE being used both as typedef and function-like macro
there. Converted manually.
Line breaks tidied up manually. One nested declaration of @local_err
deleted manually. Preexisting unwanted blank line dropped in
hw/riscv/sifive_e.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200707160613.848843-35-armbru@redhat.com>
The previous commit enables conversion of
visit_foo(..., &err);
if (err) {
...
}
to
if (!visit_foo(..., errp)) {
...
}
for visitor functions that now return true / false on success / error.
Coccinelle script:
@@
identifier fun =~ "check_list|input_type_enum|lv_start_struct|lv_type_bool|lv_type_int64|lv_type_str|lv_type_uint64|output_type_enum|parse_type_bool|parse_type_int64|parse_type_null|parse_type_number|parse_type_size|parse_type_str|parse_type_uint64|print_type_bool|print_type_int64|print_type_null|print_type_number|print_type_size|print_type_str|print_type_uint64|qapi_clone_start_alternate|qapi_clone_start_list|qapi_clone_start_struct|qapi_clone_type_bool|qapi_clone_type_int64|qapi_clone_type_null|qapi_clone_type_number|qapi_clone_type_str|qapi_clone_type_uint64|qapi_dealloc_start_list|qapi_dealloc_start_struct|qapi_dealloc_type_anything|qapi_dealloc_type_bool|qapi_dealloc_type_int64|qapi_dealloc_type_null|qapi_dealloc_type_number|qapi_dealloc_type_str|qapi_dealloc_type_uint64|qobject_input_check_list|qobject_input_check_struct|qobject_input_start_alternate|qobject_input_start_list|qobject_input_start_struct|qobject_input_type_any|qobject_input_type_bool|qobject_input_type_bool_keyval|qobject_input_type_int64|qobject_input_type_int64_keyval|qobject_input_type_null|qobject_input_type_number|qobject_input_type_number_keyval|qobject_input_type_size_keyval|qobject_input_type_str|qobject_input_type_str_keyval|qobject_input_type_uint64|qobject_input_type_uint64_keyval|qobject_output_start_list|qobject_output_start_struct|qobject_output_type_any|qobject_output_type_bool|qobject_output_type_int64|qobject_output_type_null|qobject_output_type_number|qobject_output_type_str|qobject_output_type_uint64|start_list|visit_check_list|visit_check_struct|visit_start_alternate|visit_start_list|visit_start_struct|visit_type_.*";
expression list args;
typedef Error;
Error *err;
@@
- fun(args, &err);
- if (err)
+ if (!fun(args, &err))
{
...
}
A few line breaks tidied up manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-19-armbru@redhat.com>
The only way object_property_add() can fail is when a property with
the same name already exists. Since our property names are all
hardcoded, failure is a programming error, and the appropriate way to
handle it is passing &error_abort.
Same for its variants, except for object_property_add_child(), which
additionally fails when the child already has a parent. Parentage is
also under program control, so this is a programming error, too.
We have a bit over 500 callers. Almost half of them pass
&error_abort, slightly fewer ignore errors, one test case handles
errors, and the remaining few callers pass them to their own callers.
The previous few commits demonstrated once again that ignoring
programming errors is a bad idea.
Of the few ones that pass on errors, several violate the Error API.
The Error ** argument must be NULL, &error_abort, &error_fatal, or a
pointer to a variable containing NULL. Passing an argument of the
latter kind twice without clearing it in between is wrong: if the
first call sets an error, it no longer points to NULL for the second
call. ich9_pm_add_properties(), sparc32_ledma_realize(),
sparc32_dma_realize(), xilinx_axidma_realize(), xilinx_enet_realize()
are wrong that way.
When the one appropriate choice of argument is &error_abort, letting
users pick the argument is a bad idea.
Drop parameter @errp and assert the preconditions instead.
There's one exception to "duplicate property name is a programming
error": the way object_property_add() implements the magic (and
undocumented) "automatic arrayification". Don't drop @errp there.
Instead, rename object_property_add() to object_property_try_add(),
and add the obvious wrapper object_property_add().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-15-armbru@redhat.com>
[Two semantic rebase conflicts resolved]
In my "build everything" tree, changing hw/hw.h triggers a recompile
of some 2600 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
The previous commits have left only the declaration of hw_error() in
hw/hw.h. This permits dropping most of its inclusions. Touching it
now recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-19-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/irq.h triggers a recompile
of some 5400 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get qemu_irq and.or qemu_irq_handler.
Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed. Touching it now recompiles only some 500 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-13-armbru@redhat.com>
It is never supposed to fail and cannot return an error, so just
have it return the proper type. Have it return 0xff on nothing
available, since that's what would happen on a real bus.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
While most developers are now using UTF-8 environments, it's
harder to guarantee that error messages will be output to
a multibyte locale. Rather than risking error messages that
get corrupted into mojibake when the user runs qemu in a
non-multibyte locale, let's stick to straight ASCII error
messages, rather than assuming that our use of UTF-8 in source
code string constants will work unchanged in other locales.
Found with:
$ LC_ALL=C git grep -l $'".*[\x80-\xff].*"' origin -- '**/*.[ch]' | cat
origin:hw/misc/tmp105.c
origin:hw/misc/tmp421.c
Reported-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20181120203628.2367003-1-eblake@redhat.com>
[lv: added command line to find non ASCII characters]
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
I2CSlaveClass::init is no more used, remove it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180419212727.26095-3-f4bug@amsat.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180528144509.15812-3-armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Replace all occurs of __FUNCTION__ except for the check in checkpatch
with the non GCC specific __func__.
One line in hcd-musb.c was manually tweaked to pass checkpatch.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
[THH: Removed hunks related to pxa2xx_mmci.c (fixed already)]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add a return value to the event handler. Some I2C devices will
NAK if they have no data, so allow them to do this. This required
the following changes:
Go through all the event handlers and change them to return int
and return 0.
Modify i2c_start_transfer to terminate the transaction on a NAK.
Modify smbus handing to not assert if a NAK occurs on a second
operation, and terminate the transaction and return -1 instead.
Add some information on semantics to I2CSlaveClass.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit 57cb38b included qapi/error.h into qemu/osdep.h to get the
Error typedef. Since then, we've moved to include qemu/osdep.h
everywhere. Its file comment explains: "To avoid getting into
possible circular include dependencies, this file should not include
any other QEMU headers, with the exceptions of config-host.h,
compiler.h, os-posix.h and os-win32.h, all of which are doing a
similar job to this file and are under similar constraints."
qapi/error.h doesn't do a similar job, and it doesn't adhere to
similar constraints: it includes qapi-types.h. That's in excess of
100KiB of crap most .c files don't actually need.
Add the typedef to qemu/typedefs.h, and include that instead of
qapi/error.h. Include qapi/error.h in .c files that need it and don't
get it now. Include qapi-types.h in qom/object.h for uint16List.
Update scripts/clean-includes accordingly. Update it further to match
reality: replace config.h by config-target.h, add sysemu/os-posix.h,
sysemu/os-win32.h. Update the list of includes in the qemu/osdep.h
comment quoted above similarly.
This reduces the number of objects depending on qapi/error.h from "all
of them" to less than a third. Unfortunately, the number depending on
qapi-types.h shrinks only a little. More work is needed for that one.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
[Fix compilation without the spice devel packages. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Similar to the previous patch, it's nice to have all functions
in the tree that involve a visitor and a name for conversion to
or from QAPI to consistently stick the 'name' parameter next
to the Visitor parameter.
Done by manually changing include/qom/object.h and qom/object.c,
then running this Coccinelle script and touching up the fallout
(Coccinelle insisted on adding some trailing whitespace).
@ rule1 @
identifier fn;
typedef Object, Visitor, Error;
identifier obj, v, opaque, name, errp;
@@
void fn
- (Object *obj, Visitor *v, void *opaque, const char *name,
+ (Object *obj, Visitor *v, const char *name, void *opaque,
Error **errp) { ... }
@@
identifier rule1.fn;
expression obj, v, opaque, name, errp;
@@
fn(obj, v,
- opaque, name,
+ name, opaque,
errp)
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1454075341-13658-20-git-send-email-eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
JSON uses "name":value, but many of our visitor interfaces were
called with visit_type_FOO(v, &value, name, errp). This can be
a bit confusing to have to mentally swap the parameter order to
match JSON order. It's particularly bad for visit_start_struct(),
where the 'name' parameter is smack in the middle of the
otherwise-related group of 'obj, kind, size' parameters! It's
time to do a global swap of the parameter ordering, so that the
'name' parameter is always immediately after the Visitor argument.
Additional reason in favor of the swap: the existing include/qjson.h
prefers listing 'name' first in json_prop_*(), and I have plans to
unify that file with the qapi visitors; listing 'name' first in
qapi will minimize churn to the (admittedly few) qjson.h clients.
Later patches will then fix docs, object.h, visitor-impl.h, and
those clients to match.
Done by first patching scripts/qapi*.py by hand to make generated
files do what I want, then by running the following Coccinelle
script to affect the rest of the code base:
$ spatch --sp-file script `git grep -l '\bvisit_' -- '**/*.[ch]'`
I then had to apply some touchups (Coccinelle insisted on TAB
indentation in visitor.h, and botched the signature of
visit_type_enum() by rewriting 'const char *const strings[]' to
the syntactically invalid 'const char*const[] strings'). The
movement of parameters is sufficient to provoke compiler errors
if any callers were missed.
// Part 1: Swap declaration order
@@
type TV, TErr, TObj, T1, T2;
identifier OBJ, ARG1, ARG2;
@@
void visit_start_struct
-(TV v, TObj OBJ, T1 ARG1, const char *name, T2 ARG2, TErr errp)
+(TV v, const char *name, TObj OBJ, T1 ARG1, T2 ARG2, TErr errp)
{ ... }
@@
type bool, TV, T1;
identifier ARG1;
@@
bool visit_optional
-(TV v, T1 ARG1, const char *name)
+(TV v, const char *name, T1 ARG1)
{ ... }
@@
type TV, TErr, TObj, T1;
identifier OBJ, ARG1;
@@
void visit_get_next_type
-(TV v, TObj OBJ, T1 ARG1, const char *name, TErr errp)
+(TV v, const char *name, TObj OBJ, T1 ARG1, TErr errp)
{ ... }
@@
type TV, TErr, TObj, T1, T2;
identifier OBJ, ARG1, ARG2;
@@
void visit_type_enum
-(TV v, TObj OBJ, T1 ARG1, T2 ARG2, const char *name, TErr errp)
+(TV v, const char *name, TObj OBJ, T1 ARG1, T2 ARG2, TErr errp)
{ ... }
@@
type TV, TErr, TObj;
identifier OBJ;
identifier VISIT_TYPE =~ "^visit_type_";
@@
void VISIT_TYPE
-(TV v, TObj OBJ, const char *name, TErr errp)
+(TV v, const char *name, TObj OBJ, TErr errp)
{ ... }
// Part 2: swap caller order
@@
expression V, NAME, OBJ, ARG1, ARG2, ERR;
identifier VISIT_TYPE =~ "^visit_type_";
@@
(
-visit_start_struct(V, OBJ, ARG1, NAME, ARG2, ERR)
+visit_start_struct(V, NAME, OBJ, ARG1, ARG2, ERR)
|
-visit_optional(V, ARG1, NAME)
+visit_optional(V, NAME, ARG1)
|
-visit_get_next_type(V, OBJ, ARG1, NAME, ERR)
+visit_get_next_type(V, NAME, OBJ, ARG1, ERR)
|
-visit_type_enum(V, OBJ, ARG1, ARG2, NAME, ERR)
+visit_type_enum(V, NAME, OBJ, ARG1, ARG2, ERR)
|
-VISIT_TYPE(V, OBJ, NAME, ERR)
+VISIT_TYPE(V, NAME, OBJ, ERR)
)
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1454075341-13658-19-git-send-email-eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-25-git-send-email-peter.maydell@linaro.org
After commit 767adce2d, they are redundant. This way we don't assign them
except when needed. Once there, there were lots of cases where the ".fields"
indentation was wrong:
.fields = (VMStateField []) {
and
.fields = (VMStateField []) {
Change all the combinations to:
.fields = (VMStateField[]){
The biggest problem (apart from aesthetics) was that checkpatch complained
when we copy&pasted the code from one place to another.
Signed-off-by: Juan Quintela <quintela@redhat.com>
[PMM: fixed minor conflict, corrected commit message typos]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Using error_is_set(ERRP) to find out whether a function failed is
either wrong, fragile, or unnecessarily opaque. It's wrong when ERRP
may be null, because errors go undetected when it is. It's fragile
when proving ERRP non-null involves a non-local argument. Else, it's
unnecessarily opaque (see commit 84d18f0).
I guess the error_is_set(errp) in the ObjectProperty set() methods are
merely fragile right now, because I can't find a call chain that
passes a null errp argument.
Make the code more robust and more obviously correct: receive the
error in a local variable, then propagate it through the parameter.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Right now, the temperature property must be written in milli-celsius,
but it reads back the value in 8.8 fixed point. Fix this by letting the
property read back the original value (possibly rounded). Also simplify
the code that does the conversion.
Before:
(QEMU) qom-set path=/machine/peripheral/sensor property=temperature value=20000
{u'return': {}}
(QEMU) qom-get path=sensor property=temperature
{u'return': 5120}
After:
(QEMU) qom-set path=/machine/peripheral/sensor property=temperature value=20000
{u'return': {}}
(QEMU) qom-get path=sensor property=temperature
{u'return': 20000}
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
