Instead of casting an address within a uint8_t array to a
uint32_t*, use stl_le_p(). This handles possibly misaligned
addresses which would otherwise crash on some hosts.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Tested-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The ctucan driver defines types for its registers which are a union
of a uint32_t with a struct with bitfields for the individual
fields within that register. This is a bad idea, because bitfields
aren't portable. The ctu_can_fd_regs.h header works around the
most glaring of the portability issues by defining the
fields in two different orders depending on the setting of the
__LITTLE_ENDIAN_BITFIELD define. However, in ctucan_core.h this
is unconditionally set to 1, which is wrong for big-endian hosts.
Set it only if HOST_WORDS_BIGENDIAN is not set. There is no need
for a "have we defined it already" guard, because the only place
that should set it is ctucan_core.h, which has the usual
double-inclusion guard.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Tested-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Coverity points out that in ctucan_send_ready_buffers() we
set buff_st_mask = 0xf << (i * 4) inside the loop, but then
we never use it before overwriting it later.
The only thing we use the mask for is as part of the code that is
inserting the new buff_st field into tx_status. That is more
comprehensibly written using deposit32(), so do that and drop the
mask variable entirely.
We also update the buff_st local variable at multiple points
during this function, but nothing can ever see these
intermediate values, so just drop those, write the final
TXT_TOK as a fixed constant value, and collapse the only
remaining set/use of buff_st down into an extract32().
Fixes: Coverity CID 1432869
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Tested-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The ctucan device has 4 CAN bus cores, each of which has a set of 20
32-bit registers for writing the transmitted data. The registers are
however not contiguous; each core's buffers is 0x100 bytes after
the last.
We got the checks on the address wrong in the ctucan_mem_write()
function:
* the first "is addr in range at all" check allowed
addr == CTUCAN_CORE_MEM_SIZE, which is actually the first
byte off the end of the range
* the decode of addresses into core-number plus offset in the
tx buffer for that core failed to check that the offset was
in range, so the guest could write off the end of the
tx_buffer[] array
NB: currently the values of CTUCAN_CORE_MEM_SIZE, CTUCAN_CORE_TXBUF_NUM,
etc, make "buff_num >= CTUCAN_CORE_TXBUF_NUM" impossible, but we
retain this as a runtime check rather than an assertion to permit
those values to be changed in future (in hardware they are
configurable synthesis parameters).
Fix the top level check, and check the offset is within the buffer.
Fixes: Coverity CID 1432874
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Tested-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Jason Wang <jasowang@redhat.com>
If the peer's type is vdpa, we need to set the mac address to hardware
in virtio_net_device_realize,
Signed-off-by: Cindy Lu <lulu@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
[dwg] The stack frame itself probably isn't that big a deal, but
avoiding alloca() is generally recommended these days.
Signed-off-by: Elena Afanasova <eafanasova@gmail.com>
Message-Id: <8f07132478469b35fb50a4706691e2b56b10a67b.camel@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Check if an address is free on the bus before plugging in the
device. This makes it possible to do the check without any
side effects, and to detect the problem early without having
to do it in the realize callback.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20201006123904.610658-5-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The original CAN_PCI config option enables multiple SJA1000 PCI boards
emulation build. These boards bridge SJA1000 into I/O or memory
address space of the host CPU and depend on SJA1000 emulation.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Message-Id: <dd332de687bfe52bbec37f5de1d861fb8e620d74.1600069689.git.pisa@cmp.felk.cvut.cz>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The implementation of the model of complete open-source/design/hardware
CAN FD controller. The IP core project has been started and is maintained
by Ondrej Ille at Czech Technical University in Prague.
CTU CAN FD project pages:
https://gitlab.fel.cvut.cz/canbus/ctucanfd_ip_core
CAN bus CTU FEE Projects Listing page:
http://canbus.pages.fel.cvut.cz/
The core is mapped to PCIe card same as on one of its real hardware
adaptations. The device implementing two CTU CAN FD ip cores
is instantiated after CAN bus definition
-object can-bus,id=canbus0-bus
by QEMU parameters
-device ctucan_pci,canbus0=canbus0-bus,canbus1=canbus0-bus
Signed-off-by: Jan Charvat <charvj10@fel.cvut.cz>
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Message-Id: <23e3ca4dcb2cc9900991016910a6cab7686c0e31.1600069689.git.pisa@cmp.felk.cvut.cz>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Definitions of registers and CAN FD frame message box of CTU CAN FD
IP core are generated the specification in CACTUS/IP-XACT format.
CTU CAN FD IP core repository
https://gitlab.fel.cvut.cz/canbus/ctucanfd_ip_core
The location of the CTU CAN IP core specification within
IP core design
spec/CTU/ip/CAN_FD_IP_Core/2.1/CAN_FD_IP_Core.2.1.xml
The header files are generated by pyXact_generator designed
by Ondrej Ille which is based on ipyxact_parser.
The specification is source of header files for driver and emulation,
documentation and VHDL registers map implementation.
Signed-off-by: Jan Charvat <charvj10@fel.cvut.cz>
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Message-Id: <97ae620f724bf1d76f127aaf628f7aec3af0a11c.1600069689.git.pisa@cmp.felk.cvut.cz>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
clang's C11 atomic_fetch_*() functions only take a C11 atomic type
pointer argument. QEMU uses direct types (int, etc) and this causes a
compiler error when a QEMU code calls these functions in a source file
that also included <stdatomic.h> via a system header file:
$ CC=clang CXX=clang++ ./configure ... && make
../util/async.c:79:17: error: address argument to atomic operation must be a pointer to _Atomic type ('unsigned int *' invalid)
Avoid using atomic_*() names in QEMU's atomic.h since that namespace is
used by <stdatomic.h>. Prefix QEMU's APIs with 'q' so that atomic.h
and <stdatomic.h> can co-exist. I checked /usr/include on my machine and
searched GitHub for existing "qatomic_" users but there seem to be none.
This patch was generated using:
$ git grep -h -o '\<atomic\(64\)\?_[a-z0-9_]\+' include/qemu/atomic.h | \
sort -u >/tmp/changed_identifiers
$ for identifier in $(</tmp/changed_identifiers); do
sed -i "s%\<$identifier\>%q$identifier%g" \
$(git grep -I -l "\<$identifier\>")
done
I manually fixed line-wrap issues and misaligned rST tables.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200923105646.47864-1-stefanha@redhat.com>
- Fixes a bug in printing trap causes
- Allows 16-bit writes to the SiFive test device. This fixes the
failure to reboot the RISC-V virt machine
- Support for the Microchip PolarFire SoC and Icicle Kit
- A reafactor of RISC-V code out of hw/riscv
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAl9aa4YACgkQIeENKd+X
cFTJjgf5ASfFIO5HqP1l80/UM5Pswyq0IROZDq0ItZa6U4EPzLXoE2N0POriIj4h
Ds2JbMg0ORDqY0VbSxHlgYHMgJ9S6cuVOMnATsPG0d2jaJ3gSxLBu5k/1ENqe+Vw
sSYXZv5uEAUfOFz99zbuhKHct5HzlmBFW9dVHdflUQS+cRgsSXq27mz1BvZ8xMWl
lMhwubqdoNx0rOD3vKnlwrxaf54DcJ2IQT3BtTCjEar3tukdNaLijAuwt2hrFyr+
IwpeFXA/NWar+mXP3M+BvcLaI33j73/ac2+S5SJuzHGp/ot5nT5gAuq3PDEjHMeS
t6z9Exp776VXxNE2iUA5NB65Yp3/6w==
=07oA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/alistair/tags/pull-riscv-to-apply-20200910' into staging
This PR includes multiple fixes and features for RISC-V:
- Fixes a bug in printing trap causes
- Allows 16-bit writes to the SiFive test device. This fixes the
failure to reboot the RISC-V virt machine
- Support for the Microchip PolarFire SoC and Icicle Kit
- A reafactor of RISC-V code out of hw/riscv
# gpg: Signature made Thu 10 Sep 2020 19:08:06 BST
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [full]
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-to-apply-20200910: (30 commits)
hw/riscv: Sort the Kconfig options in alphabetical order
hw/riscv: Drop CONFIG_SIFIVE
hw/riscv: Always build riscv_hart.c
hw/riscv: Move sifive_test model to hw/misc
hw/riscv: Move sifive_uart model to hw/char
hw/riscv: Move riscv_htif model to hw/char
hw/riscv: Move sifive_plic model to hw/intc
hw/riscv: Move sifive_clint model to hw/intc
hw/riscv: Move sifive_gpio model to hw/gpio
hw/riscv: Move sifive_u_otp model to hw/misc
hw/riscv: Move sifive_u_prci model to hw/misc
hw/riscv: Move sifive_e_prci model to hw/misc
hw/riscv: sifive_u: Connect a DMA controller
hw/riscv: clint: Avoid using hard-coded timebase frequency
hw/riscv: microchip_pfsoc: Hook GPIO controllers
hw/riscv: microchip_pfsoc: Connect 2 Cadence GEMs
hw/arm: xlnx: Set all boards' GEM 'phy-addr' property value to 23
hw/net: cadence_gem: Add a new 'phy-addr' property
hw/riscv: microchip_pfsoc: Connect a DMA controller
hw/dma: Add SiFive platform DMA controller emulation
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# hw/riscv/trace-events
qemu_hexdump()'s pointer to the buffer and length of the
buffer are closely related arguments but are widely separated
in the argument list order (also, the format of <stdio.h>
function prototypes is usually to have the FILE* argument
coming first).
Reorder the arguments as "fp, prefix, buf, size" which is
more logical.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20200822180950.1343963-3-f4bug@amsat.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Most uses of qemu_hexdump() do not take an array of char
as input, forcing use of cast. Since we can use this
helper to dump any kind of buffer, use a pointer to void
argument instead.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20200822180950.1343963-2-f4bug@amsat.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
When cadence_gem model was created for Xilinx boards, the PHY address
was hard-coded to 23 in the GEM model. Now that we have introduced a
property we can use that to tell GEM model what our PHY address is.
Change all boards' GEM 'phy-addr' property value to 23, and set the
PHY address default value to 0 in the GEM model.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-13-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present the PHY address of the PHY connected to GEM is hard-coded
to either 23 (BOARD_PHY_ADDRESS) or 0. This might not be the case for
all boards. Add a new 'phy-addr' property so that board can specify
the PHY address for each GEM instance.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-12-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This makes the code consistent with the rest of QOM code in QEMU,
and will make automated conversion to type declaration macros
simpler.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200824215936.2961951-5-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
* New Supermicro X11 BMC machine (Erik)
* Fixed valid access size on AST2400 SCU
* Improved robustness of the ftgmac100 model.
* New flash models in m25p80 (Igor)
* Fixed reset sequence of SDHCI/eMMC controllers
* Improved support of the AST2600 SDMC (Joel)
* Couple of SMC cleanups
-----BEGIN PGP SIGNATURE-----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=ZQHA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/legoater/tags/pull-aspeed-20200901' into staging
Various fixes of Aspeed machines :
* New Supermicro X11 BMC machine (Erik)
* Fixed valid access size on AST2400 SCU
* Improved robustness of the ftgmac100 model.
* New flash models in m25p80 (Igor)
* Fixed reset sequence of SDHCI/eMMC controllers
* Improved support of the AST2600 SDMC (Joel)
* Couple of SMC cleanups
# gpg: Signature made Tue 01 Sep 2020 13:39:20 BST
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* remotes/legoater/tags/pull-aspeed-20200901:
hw: add a number of SPI-flash's of m25p80 family
arm: aspeed: add strap define `25HZ` of AST2500
aspeed/smc: Open AHB window of the second chip of the AST2600 FMC controller
aspeed/sdmc: Simplify calculation of RAM bits
aspeed/sdmc: Allow writes to unprotected registers
aspeed/sdmc: Perform memory training
ftgmac100: Improve software reset
ftgmac100: Fix integer overflow in ftgmac100_do_tx()
ftgmac100: Check for invalid len and address before doing a DMA transfer
ftgmac100: Change interrupt status when a DMA error occurs
ftgmac100: Fix interrupt status "Packet moved to RX FIFO"
ftgmac100: Fix interrupt status "Packet transmitted on ethernet"
ftgmac100: Fix registers that can be read
aspeed/sdhci: Fix reset sequence
aspeed/smc: Fix max_slaves of the legacy SMC device
aspeed/smc: Fix MemoryRegionOps definition
hw/arm/aspeed: Add board model for Supermicro X11 BMC
aspeed/scu: Fix valid access size on AST2400
m25p80: Add support for n25q512ax3
m25p80: Return the JEDEC ID twice for mx25l25635e
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The software reset of the MAC needs a finer granularity. Some settings
in MACCR are kept.
Cc: Frederic Konrad <konrad.frederic@yahoo.fr>
Fixes: bd44300d1a ("net: add FTGMAC100 support")
Message-Id: <20200819100956.2216690-16-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
When inserting the VLAN tag in packets, memmove() can generate an
integer overflow for packets whose length is less than 12 bytes.
Move the VLAN insertion when the last segment of the frame is reached
and check length against the size of the ethernet header (14 bytes) to
avoid the crash. Return FTGMAC100_INT_XPKT_LOST status if the frame is
too small. This seems like a good modeling choice even if Aspeed does
not specify anything in that case.
Cc: Frederic Konrad <konrad.frederic@yahoo.fr>
Cc: Mauro Matteo Cascella <mcascell@redhat.com>
Reported-by: Ziming Zhang <ezrakiez@gmail.com>
Message-Id: <20200819100956.2216690-15-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
According to the Aspeed specs, no interrupts are raised in that case
but a "Tx-packets lost" status seems like a good modeling choice for
all implementations. It is covered by the Linux kernel.
Cc: Frederic Konrad <konrad.frederic@yahoo.fr>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20200819100956.2216690-14-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The model uses today the "Normal priority transmit buffer unavailable"
interrupt status which it is not appropriate. According to the Aspeed
specs, no interrupts are raised in that case. An "AHB error" status
seems like a better modeling choice for all implementations since it
is covered by the Linux kernel.
Cc: Frederic Konrad <konrad.frederic@yahoo.fr>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20200819100956.2216690-13-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
As we don't model the RX or TX FIFO, raise the "Packet moved to RX
FIFO" interrupt status bit as soon as we are handling a RX packet.
Cc: Frederic Konrad <konrad.frederic@yahoo.fr>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20200819100956.2216690-12-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The second field of the TX descriptor has a set of flags to choose
when the transmit interrupt is raised : after the packet has been sent
on the ethernet or after it has been moved into the TX FIFO. But we
don't model that today.
Simply raise the "Packet transmitted on ethernet" interrupt status bit
as soon as the packet is sent by QEMU.
Cc: Frederic Konrad <konrad.frederic@yahoo.fr>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20200819100956.2216690-11-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Receive Ring Base Address Register (RXR_BADR) and the Normal Priority
Transmit Receive Ring Base Address Register (NPTXR_BADR) can also be
read.
Cc: Frederic Konrad <konrad.frederic@yahoo.fr>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20200819100956.2216690-10-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Clang static code analyzer show warning:
hw/net/virtio-net.c:2077:5: warning: Value stored to 'tcp_flag' is never read
tcp_flag &= VIRTIO_NET_TCP_FLAG;
^ ~~~~~~~~~~~~~~~~~~~
The 'VIRTIO_NET_TCP_FLAG' is '0x3F'. The last ‘tcp_flag’ assignment statement is
the same as that of the first two statements.
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Chen Qun <kuhn.chenqun@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20200827110311.164316-7-kuhn.chenqun@huawei.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Most of the MDIOBus fields are unused. The ADVERTISE_10HALF
definition is unused. Remove unused code.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-Id: <20200814133007.16850-1-f4bug@amsat.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Add fallthrough annotations to be able to compile the code without
warnings when using -Wimplicit-fallthrough in our CFLAGS. Looking
at the code, it seems like the fallthrough is indeed intended here,
so the comments should be appropriate.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Message-Id: <20200630075520.29825-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Remove superfluous breaks, as there is a "return" before them.
Signed-off-by: Liao Pingfang <liao.pingfang@zte.com.cn>
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1594631126-36631-1-git-send-email-wang.yi59@zte.com.cn>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Allow the device to execute the DMA transfers in a different
AddressSpace.
The H3 SoC keeps using the system_memory address space,
but via the proper dma_memory_access() API.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20200814122907.27732-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This will make future conversion to use OBJECT_DECLARE* easier.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Message-Id: <20200826184334.4120620-2-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-39-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move typedef closer to the type check macros, to make it easier
to convert the code to OBJECT_DEFINE_TYPE() in the future.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-21-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move typedef closer to the type check macros, to make it easier
to convert the code to OBJECT_DEFINE_TYPE() in the future.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-16-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Rename the E1000_DEVICE_CLASS() and E1000_DEVICE_GET_CLASS()
macros to be consistent with the E1000() instance cast macro.
This will allow us to register the type cast macros using
OBJECT_DECLARE_TYPE later.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-2-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Meson doesn't enjoy the same flexibility we have with Make in choosing
the include path. In particular the tracing headers are using
$(build_root)/$(<D).
In order to keep the include directives unchanged,
the simplest solution is to generate headers with patterns like
"trace/trace-audio.h" and place forwarding headers in the source tree
such that for example "audio/trace.h" includes "trace/trace-audio.h".
This patch is too ugly to be applied to the Makefiles now. It's only
a way to separate the changes to the tracing header files from the
Meson rewrite of the tracing logic.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
An assertion failure issue was found in the code that processes network packets
while adding data fragments into the packet context. It could be abused by a
malicious guest to abort the QEMU process on the host. This patch replaces the
affected assert() with a conditional statement, returning false if the current
data fragment exceeds max_raw_frags.
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Reported-by: Ziming Zhang <ezrakiez@gmail.com>
Reviewed-by: Dmitry Fleytman <dmitry.fleytman@gmail.com>
Signed-off-by: Mauro Matteo Cascella <mcascell@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
We try to check whether a peer is VDPA in order to get config from
there - with no peer, this leads to a NULL
pointer dereference. Add a check before trying to access the peer
type. No peer means not VDPA.
Fixes: 108a64818e ("vhost-vdpa: introduce vhost-vdpa backend")
Cc: Cindy Lu <lulu@redhat.com>
Tested-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
A buffer overflow issue was reported by Mr. Ziming Zhang, CC'd here. It
occurs while sending an Ethernet frame due to missing break statements
and improper checking of the buffer size.
Reported-by: Ziming Zhang <ezrakiez@gmail.com>
Signed-off-by: Mauro Matteo Cascella <mcascell@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1708065
With network backend with 'virtual header' - there was an issue
in 'plen' field. Overall, during TSO, 'plen' would be changed,
but with 'vheader' this field should be set to the size of the
payload itself instead of '0'.
Signed-off-by: Andrew Melnychenko <andrew@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The test of the write of the dblac register was testing the old value
instead of the new value. This would accept the write of an invalid value
but subsequently refuse any following valid writes.
Signed-off-by: erik-smit <erik.lucas.smit@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Added fix for checksum offload for IPv6 if a backend doesn't
have a virtual header.
This patch is a part of IPv6 fragmentation.
Signed-off-by: Andrew Melnychenko <andrew@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
If you have a networking device and its virtio failover device, and
you remove them in this order:
- virtio device
- the real device
You get qemu crash.
See bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1820120
Bug exist on qemu 4.2 and 5.0.
But in 5.0 don't shows because commit
77b06bba62
somehow papers over it.
CC: Jason Wang <jasowang@redhat.com>
CC: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
When all we do with an Error we receive into a local variable is
propagating to somewhere else, we can just as well receive it there
right away, even when we need to keep error_propagate() for other
error paths.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200707160613.848843-38-armbru@redhat.com>
The object_property_set_FOO() setters take property name and value in
an unusual order:
void object_property_set_FOO(Object *obj, FOO_TYPE value,
const char *name, Error **errp)
Having to pass value before name feels grating. Swap them.
Same for object_property_set(), object_property_get(), and
object_property_parse().
Convert callers with this Coccinelle script:
@@
identifier fun = {
object_property_get, object_property_parse, object_property_set_str,
object_property_set_link, object_property_set_bool,
object_property_set_int, object_property_set_uint, object_property_set,
object_property_set_qobject
};
expression obj, v, name, errp;
@@
- fun(obj, v, name, errp)
+ fun(obj, name, v, errp)
Chokes on hw/arm/musicpal.c's lcd_refresh() with the unhelpful error
message "no position information". Convert that one manually.
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Convert manually.
Fails to convert hw/rx/rx-gdbsim.c, because Coccinelle gets confused
by RXCPU being used both as typedef and function-like macro there.
Convert manually. The other files using RXCPU that way don't need
conversion.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-27-armbru@redhat.com>
[Straightforwad conflict with commit 2336172d9b "audio: set default
value for pcspk.iobase property" resolved]
The previous commit used Coccinelle to convert from checking the Error
object to checking the return value. Convert a few more manually.
Also tweak control flow in places to conform to the conventional "if
error bail out" pattern.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-20-armbru@redhat.com>
The previous commit enables conversion of
visit_foo(..., &err);
if (err) {
...
}
to
if (!visit_foo(..., errp)) {
...
}
for visitor functions that now return true / false on success / error.
Coccinelle script:
@@
identifier fun =~ "check_list|input_type_enum|lv_start_struct|lv_type_bool|lv_type_int64|lv_type_str|lv_type_uint64|output_type_enum|parse_type_bool|parse_type_int64|parse_type_null|parse_type_number|parse_type_size|parse_type_str|parse_type_uint64|print_type_bool|print_type_int64|print_type_null|print_type_number|print_type_size|print_type_str|print_type_uint64|qapi_clone_start_alternate|qapi_clone_start_list|qapi_clone_start_struct|qapi_clone_type_bool|qapi_clone_type_int64|qapi_clone_type_null|qapi_clone_type_number|qapi_clone_type_str|qapi_clone_type_uint64|qapi_dealloc_start_list|qapi_dealloc_start_struct|qapi_dealloc_type_anything|qapi_dealloc_type_bool|qapi_dealloc_type_int64|qapi_dealloc_type_null|qapi_dealloc_type_number|qapi_dealloc_type_str|qapi_dealloc_type_uint64|qobject_input_check_list|qobject_input_check_struct|qobject_input_start_alternate|qobject_input_start_list|qobject_input_start_struct|qobject_input_type_any|qobject_input_type_bool|qobject_input_type_bool_keyval|qobject_input_type_int64|qobject_input_type_int64_keyval|qobject_input_type_null|qobject_input_type_number|qobject_input_type_number_keyval|qobject_input_type_size_keyval|qobject_input_type_str|qobject_input_type_str_keyval|qobject_input_type_uint64|qobject_input_type_uint64_keyval|qobject_output_start_list|qobject_output_start_struct|qobject_output_type_any|qobject_output_type_bool|qobject_output_type_int64|qobject_output_type_null|qobject_output_type_number|qobject_output_type_str|qobject_output_type_uint64|start_list|visit_check_list|visit_check_struct|visit_start_alternate|visit_start_list|visit_start_struct|visit_type_.*";
expression list args;
typedef Error;
Error *err;
@@
- fun(args, &err);
- if (err)
+ if (!fun(args, &err))
{
...
}
A few line breaks tidied up manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-19-armbru@redhat.com>
Currently we have 2 types of vhost backends in QEMU: vhost kernel and
vhost-user. The above patch provides a generic device for vDPA purpose,
this vDPA device exposes to user space a non-vendor-specific configuration
interface for setting up a vhost HW accelerator, this patch set introduces
a third vhost backend called vhost-vdpa based on the vDPA interface.
Vhost-vdpa usage:
qemu-system-x86_64 -cpu host -enable-kvm \
......
-netdev type=vhost-vdpa,vhostdev=/dev/vhost-vdpa-id,id=vhost-vdpa0 \
-device virtio-net-pci,netdev=vhost-vdpa0,page-per-vq=on \
Signed-off-by: Lingshan zhu <lingshan.zhu@intel.com>
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Signed-off-by: Cindy Lu <lulu@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20200701145538.22333-14-lulu@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
We need a solution to use an Ethernet PHY that is not the first device
on the MDIO bus (device 0 on MDIO bus).
As an example with the i.MX6UL the NXP SOC has 2 Ethernet devices but
only one MDIO bus on which the 2 related PHY are connected but at unique
addresses.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: a1a5c0e139d1c763194b8020573dcb6025daeefa.1593296112.git.jcd@tribudubois.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch introduces set_config & get_config method which allows
vhost_net set/get the config to backend
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20200701145538.22333-13-lulu@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
user the qemu_get_peer to replace the old process
Signed-off-by: Cindy Lu <lulu@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20200701145538.22333-3-lulu@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
The Error ** argument must be NULL, &error_abort, &error_fatal, or a
pointer to a variable containing NULL. Passing an argument of the
latter kind twice without clearing it in between is wrong: if the
first call sets an error, it no longer points to NULL for the second
call.
virtio_gpu_pci_base_realize(), virtio_vga_base_realize(),
sparc32_ledma_device_realize(), sparc32_dma_realize(),
sparc32_dma_realize() xilinx_axidma_realize(), mips_cps_realize(),
macio_realize_ide(), xilinx_enet_realize(), and
virtio_iommu_pci_realize() are wrong that way: they reuse the argument
they pass to object_property_set_link() for another call.
Harmless, because object_property_set_link() can't actually fail for
them: it fails when the property doesn't exist, is not settable, or
its .check() method fails. Fix by passing &error_abort instead.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Cc: "Edgar E. Iglesias" <edgar.iglesias@gmail.com>
Cc: Alistair Francis <alistair@alistair23.me>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Cc: Aleksandar Markovic <aleksandar.qemu.devel@gmail.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Aleksandar Rikalo <aleksandar.rikalo@syrmia.com>
Cc: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200630090351.1247703-16-armbru@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Two defects are fixed:
1/ Detection of multicast frames
2/ Treating drop of mis-addressed frames as non-error
Signed-off-by: Tong Ho <tong.ho@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
TX_LAST bit should not be set by hardware, its set by guest to inform
the last bd of the frame.
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Mask all interrupt on reset.
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Advertise support of clear-on-read for ISR registers.
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Add a property "jumbo-max-len", which sets default value of jumbo frames
up to 16,383 bytes. Add Frame length checks for standard and jumbo
frames.
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Fix the code style for register definitions.
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Moving this buffers to CadenceGEMState, as their size will be increased
more when JUMBO frames support is added.
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Set ISR according to queue in use, added interrupt support for
all queues.
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Q1 to Q7 ISR's are clear-on-read, IER/IDR registers
are write-only, mask reg are read-only.
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Set irq's specific to a queue, present implementation is setting q1 irq
based on q0 status.
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
During wrap around and reset, queues are pointing to initial base
address of queue 0, irrespective of what queue we are dealing with.
Fix it by assigning proper base address every time.
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Enabling debug breaks the build, Fix them and make debug statements
always compilable. Fix few statements to use sized integer casting.
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Log with GUEST_ERROR what the guest is doing wrong.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Bit #14 is "DE" for 'Descriptor Error':
When set, indicates a frame truncation caused by a frame
that does not fit within the current descriptor buffers,
and that the 21143 does not own the next descriptor.
[Table 4-1. RDES0 Bit Fields Description]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The tulip network driver in a qemu-system-hppa emulation is broken in
the sense that bigger network packages aren't received any longer and
thus even running e.g. "apt update" inside the VM fails.
The breakage was introduced by commit 8ffb7265af ("check frame size and
r/w data length") which added checks to prevent accesses outside of the
rx/tx buffers.
But the new checks were implemented wrong. The variable rx_frame_len
counts backwards, from rx_frame_size down to zero, and the variable len
is never bigger than rx_frame_len, so accesses just can't happen and the
checks are unnecessary.
On the contrary the checks now prevented bigger packages to be moved
into the rx buffers.
This patch reverts the wrong checks and were sucessfully tested with a
qemu-system-hppa emulation.
Fixes: 8ffb7265af ("check frame size and r/w data length")
Buglink: https://bugs.launchpad.net/bugs/1874539
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Removal of duplicated RSC definitions. Changing names of the
fields to ones defined in the Linux header.
Signed-off-by: Yuri Benditovich <yuri.benditovich@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Save and restore RSS/hash report configuration.
Signed-off-by: Yuri Benditovich <yuri.benditovich@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Suggest VIRTIO_NET_F_HASH_REPORT if specified in device
parameters.
If the VIRTIO_NET_F_HASH_REPORT is set,
the device extends configuration space. If the feature
is negotiated, the packet layout is extended to
accomodate the hash information. In this case deliver
packet's hash value and report type in virtio header
extension.
Use for configuration the same procedure as already
used for RSS. We add two fields in rss_data that
controls what the device does with the calculated hash
if rss_data.enabled is set. If field 'populate' is set
the hash is set in the packet, if field 'redirect' is
set the hash is used to decide the queue to place the
packet to.
Signed-off-by: Yuri Benditovich <yuri.benditovich@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
If VIRTIO_NET_F_RSS negotiated and RSS is enabled, process
incoming packets, calculate packet's hash and place the
packet into respective RX virtqueue.
Signed-off-by: Yuri Benditovich <yuri.benditovich@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[PMD: Fixed 32-bit format string using PRIx32/PRIx64]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The hardware supports configurable descriptor sizes, configured in the DBLAC
register.
Most drivers use the default 4 word descriptor, which is currently hardcoded,
but Aspeed SDK configures 8 words to store extra data.
Signed-off-by: Erik Smit <erik.lucas.smit@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[PMM: removed unnecessary parens]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is the transformation explained in the commit before previous.
Takes care of just one pattern that needs conversion. More to come in
this series.
Coccinelle script:
@ depends on !(file in "hw/arm/highbank.c")@
expression bus, type_name, dev, expr;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr;
identifier DOWN;
@@
- dev = DOWN(qdev_create(bus, type_name));
+ dev = DOWN(qdev_new(type_name));
... when != dev = expr
- qdev_init_nofail(DEVICE(dev));
+ qdev_realize_and_unref(DEVICE(dev), bus, &error_fatal);
@@
expression bus, type_name, expr;
identifier dev;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr, errp;
symbol true;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
@@
expression bus, type_name, expr, errp;
identifier dev;
symbol true;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
The first rule exempts hw/arm/highbank.c, because it matches along two
control flow paths there, with different @type_name. Covered by the
next commit's manual conversions.
Missing #include "qapi/error.h" added manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-10-armbru@redhat.com>
[Conflicts in hw/misc/empty_slot.c and hw/sparc/leon3.c resolved]
hw_error() calls exit(). This a bit overkill when we can log
the accesses as unimplemented or guest error.
When fuzzing the devices, we don't want the whole process to
exit. Replace some hw_error() calls by qemu_log_mask().
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200526094052.1723-3-f4bug@amsat.org>
Reviewed-by: Thomas Huth <huth@tuxfamily.org>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
The DEVICE() macro is defined as:
#define DEVICE(obj) OBJECT_CHECK(DeviceState, (obj), TYPE_DEVICE)
which expands to:
((DeviceState *)object_dynamic_cast_assert((Object *)(obj), (name),
__FILE__, __LINE__,
__func__))
This assertion can only fail when @obj points to something other
than its stated type, i.e. when we're in undefined behavior country.
Remove the unnecessary DEVICE() casts when we already know the
pointer is of DeviceState type.
Patch created mechanically using spatch with this script:
@@
typedef DeviceState;
DeviceState *s;
@@
- DEVICE(s)
+ s
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Paul Durrant <paul@xen.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Acked-by: John Snow <jsnow@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200512070020.22782-4-f4bug@amsat.org>
Devices may have component devices and buses.
Device realization may fail. Realization is recursive: a device's
realize() method realizes its components, and device_set_realized()
realizes its buses (which should in turn realize the devices on that
bus, except bus_set_realized() doesn't implement that, yet).
When realization of a component or bus fails, we need to roll back:
unrealize everything we realized so far. If any of these unrealizes
failed, the device would be left in an inconsistent state. Must not
happen.
device_set_realized() lets it happen: it ignores errors in the roll
back code starting at label child_realize_fail.
Since realization is recursive, unrealization must be recursive, too.
But how could a partly failed unrealize be rolled back? We'd have to
re-realize, which can fail. This design is fundamentally broken.
device_set_realized() does not roll back at all. Instead, it keeps
unrealizing, ignoring further errors.
It can screw up even for a device with no buses: if the lone
dc->unrealize() fails, it still unregisters vmstate, and calls
listeners' unrealize() callback.
bus_set_realized() does not roll back either. Instead, it stops
unrealizing.
Fortunately, no unrealize method can fail, as we'll see below.
To fix the design error, drop parameter @errp from all the unrealize
methods.
Any unrealize method that uses @errp now needs an update. This leads
us to unrealize() methods that can fail. Merely passing it to another
unrealize method cannot cause failure, though. Here are the ones that
do other things with @errp:
* virtio_serial_device_unrealize()
Fails when qbus_set_hotplug_handler() fails, but still does all the
other work. On failure, the device would stay realized with its
resources completely gone. Oops. Can't happen, because
qbus_set_hotplug_handler() can't actually fail here. Pass
&error_abort to qbus_set_hotplug_handler() instead.
* hw/ppc/spapr_drc.c's unrealize()
Fails when object_property_del() fails, but all the other work is
already done. On failure, the device would stay realized with its
vmstate registration gone. Oops. Can't happen, because
object_property_del() can't actually fail here. Pass &error_abort
to object_property_del() instead.
* spapr_phb_unrealize()
Fails and bails out when remove_drcs() fails, but other work is
already done. On failure, the device would stay realized with some
of its resources gone. Oops. remove_drcs() fails only when
chassis_from_bus()'s object_property_get_uint() fails, and it can't
here. Pass &error_abort to remove_drcs() instead.
Therefore, no unrealize method can fail before this patch.
device_set_realized()'s recursive unrealization via bus uses
object_property_set_bool(). Can't drop @errp there, so pass
&error_abort.
We similarly unrealize with object_property_set_bool() elsewhere,
always ignoring errors. Pass &error_abort instead.
Several unrealize methods no longer handle errors from other unrealize
methods: virtio_9p_device_unrealize(),
virtio_input_device_unrealize(), scsi_qdev_unrealize(), ...
Much of the deleted error handling looks wrong anyway.
One unrealize methods no longer ignore such errors:
usb_ehci_pci_exit().
Several realize methods no longer ignore errors when rolling back:
v9fs_device_realize_common(), pci_qdev_unrealize(),
spapr_phb_realize(), usb_qdev_realize(), vfio_ccw_realize(),
virtio_device_realize().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-17-armbru@redhat.com>
Several functions can't fail anymore: ich9_pm_add_properties(),
device_add_bootindex_property(), ppc_compat_add_property(),
spapr_caps_add_properties(), PropertyInfo.create(). Drop their @errp
parameter.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-16-armbru@redhat.com>
The only way object_property_add() can fail is when a property with
the same name already exists. Since our property names are all
hardcoded, failure is a programming error, and the appropriate way to
handle it is passing &error_abort.
Same for its variants, except for object_property_add_child(), which
additionally fails when the child already has a parent. Parentage is
also under program control, so this is a programming error, too.
We have a bit over 500 callers. Almost half of them pass
&error_abort, slightly fewer ignore errors, one test case handles
errors, and the remaining few callers pass them to their own callers.
The previous few commits demonstrated once again that ignoring
programming errors is a bad idea.
Of the few ones that pass on errors, several violate the Error API.
The Error ** argument must be NULL, &error_abort, &error_fatal, or a
pointer to a variable containing NULL. Passing an argument of the
latter kind twice without clearing it in between is wrong: if the
first call sets an error, it no longer points to NULL for the second
call. ich9_pm_add_properties(), sparc32_ledma_realize(),
sparc32_dma_realize(), xilinx_axidma_realize(), xilinx_enet_realize()
are wrong that way.
When the one appropriate choice of argument is &error_abort, letting
users pick the argument is a bad idea.
Drop parameter @errp and assert the preconditions instead.
There's one exception to "duplicate property name is a programming
error": the way object_property_add() implements the magic (and
undocumented) "automatic arrayification". Don't drop @errp there.
Instead, rename object_property_add() to object_property_try_add(),
and add the obvious wrapper object_property_add().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-15-armbru@redhat.com>
[Two semantic rebase conflicts resolved]
QOM object initialization runs .instance_init() for the type and all
its supertypes; see object_init_with_type().
Both TYPE_E1000_BASE and its concrete subtypes set .instance_init() to
e1000_instance_init(). For the concrete subtypes, it duly gets run
twice. The second run fails, but the error gets ignored (a later
commit will change that).
Remove it from the subtypes.
Cc: Jason Wang <jasowang@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-12-armbru@redhat.com>
Uses of gchar * in qom/object.h:
* ObjectProperty member @name
Functions that take a property name argument all use char *. Change
the member to match.
* ObjectProperty member @type
Functions that take a property type argument or return it all use
char *. Change the member to match.
* ObjectProperty member @description
Functions that take a property description argument all use char *.
Change the member to match.
* object_resolve_path_component() parameter @part
Path components are property names. Most callers pass char *
arguments. Change the parameter to match. Adjust the few callers
that pass gchar * to pass char *.
* Return value of object_get_canonical_path_component(),
object_get_canonical_path()
Most callers convert their return values right back to char *.
Change the return value to match. Adjust the few callers where that
would add a conversion to gchar * to use char * instead.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-3-armbru@redhat.com>
Add support for fragmented packets from the DMA.
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-Id: <20200506082513.18751-7-edgar.iglesias@gmail.com>
Some stream clients stream an endless stream of data while
other clients stream data in packets. Stream interfaces
usually have a way to signal the end of a packet or the
last beat of a transfer.
This adds an end-of-packet flag to the push interface.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-Id: <20200506082513.18751-6-edgar.iglesias@gmail.com>
Remove unncessary cast, buf is already uint8_t *.
No functional change.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200506082513.18751-4-edgar.iglesias@gmail.com>
Split the shared stream_class_init function to assign
stream->push with better type-safety.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200506082513.18751-3-edgar.iglesias@gmail.com>
Auto-clear PHY CR Autoneg bits. This makes this model
work with recent Linux kernels.
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-Id: <20200506082513.18751-2-edgar.iglesias@gmail.com>
The RX ring descriptors control field is used for setting
SOF and EOF (start of frame and end of frame).
The SOF and EOF weren't cleared from the previous descriptors,
causing inconsistencies in ring buffer.
Fix that by clearing the control field of every descriptors we're
processing.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20200418085145.489726-1-rfried.dev@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Wraparound of TX descriptor cyclic buffer only updated
the low 32 bits of the descriptor.
Fix that by checking if we're working with 64bit descriptors.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20200417171736.441607-1-rfried.dev@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Modelled Ethernet MAC of Smartfusion2 SoC.
Micrel KSZ8051 PHY is present on Emcraft's
SOM kit hence same PHY is emulated.
Signed-off-by: Subbaraya Sundeep <sundeep.lkml@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1587048891-30493-2-git-send-email-sundeep.lkml@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
virtio_net_device_realize() rejects invalid duplex and speed values.
The error handling is broken:
$ ../qemu/bld-sani/x86_64-softmmu/qemu-system-x86_64 -S -display none -monitor stdio
QEMU 4.2.93 monitor - type 'help' for more information
(qemu) device_add virtio-net,duplex=x
Error: 'duplex' must be 'half' or 'full'
(qemu) c
=================================================================
==15654==ERROR: AddressSanitizer: heap-use-after-free on address 0x62e000014590 at pc 0x560b75c8dc13 bp 0x7fffdf1a6950 sp 0x7fffdf1a6940
READ of size 8 at 0x62e000014590 thread T0
#0 0x560b75c8dc12 in object_dynamic_cast_assert /work/armbru/qemu/qom/object.c:826
#1 0x560b74c38ac0 in virtio_vmstate_change /work/armbru/qemu/hw/virtio/virtio.c:3210
#2 0x560b74d9765e in vm_state_notify /work/armbru/qemu/softmmu/vl.c:1271
#3 0x560b7494ba72 in vm_prepare_start /work/armbru/qemu/cpus.c:2156
#4 0x560b7494bacd in vm_start /work/armbru/qemu/cpus.c:2162
#5 0x560b75a7d890 in qmp_cont /work/armbru/qemu/monitor/qmp-cmds.c:160
#6 0x560b75a8d70a in hmp_cont /work/armbru/qemu/monitor/hmp-cmds.c:1043
#7 0x560b75a799f2 in handle_hmp_command /work/armbru/qemu/monitor/hmp.c:1082
[...]
0x62e000014590 is located 33168 bytes inside of 42288-byte region [0x62e00000c400,0x62e000016930)
freed by thread T1 here:
#0 0x7feadd39491f in __interceptor_free (/lib64/libasan.so.5+0x10d91f)
#1 0x7feadcebcd7c in g_free (/lib64/libglib-2.0.so.0+0x55d7c)
#2 0x560b75c8fd40 in object_unref /work/armbru/qemu/qom/object.c:1128
#3 0x560b7498a625 in memory_region_unref /work/armbru/qemu/memory.c:1762
#4 0x560b74999fa4 in do_address_space_destroy /work/armbru/qemu/memory.c:2788
#5 0x560b762362fc in call_rcu_thread /work/armbru/qemu/util/rcu.c:283
#6 0x560b761c8884 in qemu_thread_start /work/armbru/qemu/util/qemu-thread-posix.c:519
#7 0x7fead9be34bf in start_thread (/lib64/libpthread.so.0+0x84bf)
previously allocated by thread T0 here:
#0 0x7feadd394d18 in __interceptor_malloc (/lib64/libasan.so.5+0x10dd18)
#1 0x7feadcebcc88 in g_malloc (/lib64/libglib-2.0.so.0+0x55c88)
#2 0x560b75c8cf8a in object_new /work/armbru/qemu/qom/object.c:699
#3 0x560b75010ad9 in qdev_device_add /work/armbru/qemu/qdev-monitor.c:654
#4 0x560b750120c2 in qmp_device_add /work/armbru/qemu/qdev-monitor.c:805
#5 0x560b75012c1b in hmp_device_add /work/armbru/qemu/qdev-monitor.c:905
[...]
==15654==ABORTING
Cause: virtio_net_device_realize() neglects to bail out after setting
the error. Fix that.
Fixes: 9473939ed7
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200422130719.28225-9-armbru@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Fixes the following coccinelle warnings:
$ spatch --sp-file --verbose-parsing ... \
scripts/coccinelle/remove_local_err.cocci
...
SUSPICIOUS: a \ character appears outside of a #define at ./target/ppc/translate_init.inc.c:5213
SUSPICIOUS: a \ character appears outside of a #define at ./target/ppc/translate_init.inc.c:5261
SUSPICIOUS: a \ character appears outside of a #define at ./target/microblaze/cpu.c:166
SUSPICIOUS: a \ character appears outside of a #define at ./target/microblaze/cpu.c:167
SUSPICIOUS: a \ character appears outside of a #define at ./target/microblaze/cpu.c:169
SUSPICIOUS: a \ character appears outside of a #define at ./target/microblaze/cpu.c:170
SUSPICIOUS: a \ character appears outside of a #define at ./target/microblaze/cpu.c:171
SUSPICIOUS: a \ character appears outside of a #define at ./target/microblaze/cpu.c:172
SUSPICIOUS: a \ character appears outside of a #define at ./target/microblaze/cpu.c:173
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:5787
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:5789
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:5800
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:5801
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:5802
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:5804
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:5805
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:5806
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:6329
SUSPICIOUS: a \ character appears outside of a #define at ./hw/sd/sdhci.c:1133
SUSPICIOUS: a \ character appears outside of a #define at ./hw/scsi/scsi-disk.c:3081
SUSPICIOUS: a \ character appears outside of a #define at ./hw/net/virtio-net.c:1529
SUSPICIOUS: a \ character appears outside of a #define at ./hw/riscv/sifive_u.c:468
SUSPICIOUS: a \ character appears outside of a #define at ./dump/dump.c:1895
SUSPICIOUS: a \ character appears outside of a #define at ./block/vhdx.c:2209
SUSPICIOUS: a \ character appears outside of a #define at ./block/vhdx.c:2215
SUSPICIOUS: a \ character appears outside of a #define at ./block/vhdx.c:2221
SUSPICIOUS: a \ character appears outside of a #define at ./block/vhdx.c:2222
SUSPICIOUS: a \ character appears outside of a #define at ./block/replication.c:172
SUSPICIOUS: a \ character appears outside of a #define at ./block/replication.c:173
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200412223619.11284-2-f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
virtio_net_rsc_ext_num_{packets,dupacks} needs to be available
independently of the presence of VIRTIO_NET_HDR_F_RSC_INFO.
Fixes: 2974e916df ("virtio-net: support RSC v4/v6 tcp traffic for Windows HCK")
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20200427102415.10915-2-cohuck@redhat.com>
Coverity points out (CID 1421926) that the read code for
REG_ADDR_HIGH reads off the end of the buffer, because it does a
32-bit read from byte 4 of a 6-byte buffer.
The code also has an endianness issue for both REG_ADDR_HIGH and
REG_ADDR_LOW, because it will do the wrong thing on a big-endian
host.
Rewrite the read code to use ldl_le_p() and lduw_le_p() to fix this;
the write code is not incorrect, but for consistency we make it use
stl_le_p() and stw_le_p().
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Tulip network driver while copying tx/rx buffers does not check
frame size against r/w data length. This may lead to OOB buffer
access. Add check to avoid it.
Limit iterations over descriptors to avoid potential infinite
loop issue in tulip_xmit_list_update.
Reported-by: Li Qiang <pangpei.lq@antfin.com>
Reported-by: Ziming Zhang <ezrakiez@gmail.com>
Reported-by: Jason Wang <jasowang@redhat.com>
Tested-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The CanBusClientInfo::can_receive handler return whether the
device can or can not receive new frames. Make it obvious by
returning a boolean type.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The NetCanReceive handler return whether the device can or
can not receive new packets. Make it obvious by returning
a boolean type.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
We will modify this code in the next commit. Clean it up
first to avoid checkpatch.pl errors.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The smc91c111_can_receive() function simply returns a boolean value.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The e1000e_can_receive() function simply returns a boolean value.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1737400
Fixed setting max_queue_num if there are no peers in
NICConf. qemu_new_nic() creates NICState with 1 NetClientState(index
0) without peers, set max_queue_num to 0 - It prevents undefined
behavior and possible crashes, especially during pcie hotplug.
Fixes: 6f3fbe4ed0 ("net: Introduce e1000e device emulation")
Signed-off-by: Andrew Melnychenko <andrew@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Dmitry Fleytman <dmitry.fleytman@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The i82596_receive() function attempts to pass the guest a buffer
which is effectively the concatenation of the data it is passed and a
4 byte CRC value. However, rather than implementing this as "write
the data; then write the CRC" it instead bumps the length value of
the data by 4, and writes 4 extra bytes from beyond the end of the
buffer, which it then overwrites with the CRC. It also assumed that
we could always fit all four bytes of the CRC into the final receive
buffer, which might not be true if the CRC needs to be split over two
receive buffers.
Calculate separately how many bytes we need to transfer into the
guest's receive buffer from the source buffer, and how many we need
to transfer from the CRC work.
We add a count 'bufsz' of the number of bytes left in the source
buffer, which we use purely to assert() that we don't overrun.
Spotted by Coverity (CID 1419396) for the specific case when we end
up using a local array as the source buffer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The command is 32-bit, but we are loading the 16 upper bits with
the 'get_uint16(s->scb + 2)' call.
Once shifted by 16, the command bits match the status bits:
- Command
Bit 31 ACK-CX Acknowledges that the CU completed an Action Command.
Bit 30 ACK-FR Acknowledges that the RU received a frame.
Bit 29 ACK-CNA Acknowledges that the Command Unit became not active.
Bit 28 ACK-RNR Acknowledges that the Receive Unit became not ready.
- Status
Bit 15 CX The CU finished executing a command with its I(interrupt) bit set.
Bit 14 FR The RU finished receiving a frame.
Bit 13 CNA The Command Unit left the Active state.
Bit 12 RNR The Receive Unit left the Ready state.
Add the SCB_COMMAND_ACK_MASK definition to simplify the code.
This fixes Coverity 1419392 (CONSTANT_EXPRESSION_RESULT):
/hw/net/i82596.c: 352 in examine_scb()
346 cuc = (command >> 8) & 0x7;
347 ruc = (command >> 4) & 0x7;
348 DBG(printf("MAIN COMMAND %04x cuc %02x ruc %02x\n", command, cuc, ruc));
349 /* and clear the scb command word */
350 set_uint16(s->scb + 2, 0);
351
>>> CID 1419392: (CONSTANT_EXPRESSION_RESULT)
>>> "command & (2147483648UL /* 1UL << 31 */)" is always 0 regardless of the values of its operands. This occurs as the logical operand of "if".
352 if (command & BIT(31)) /* ACK-CX */
353 s->scb_status &= ~SCB_STATUS_CX;
>>> CID 1419392: (CONSTANT_EXPRESSION_RESULT)
>>> "command & (1073741824UL /* 1UL << 30 */)" is always 0 regardless of the values of its operands. This occurs as the logical operand of "if".
354 if (command & BIT(30)) /*ACK-FR */
355 s->scb_status &= ~SCB_STATUS_FR;
>>> CID 1419392: (CONSTANT_EXPRESSION_RESULT)
>>> "command & (536870912UL /* 1UL << 29 */)" is always 0 regardless of the values of its operands. This occurs as the logical operand of "if".
356 if (command & BIT(29)) /*ACK-CNA */
357 s->scb_status &= ~SCB_STATUS_CNA;
>>> CID 1419392: (CONSTANT_EXPRESSION_RESULT)
>>> "command & (268435456UL /* 1UL << 28 */)" is always 0 regardless of the values of its operands. This occurs as the logical operand of "if".
358 if (command & BIT(28)) /*ACK-RNR */
359 s->scb_status &= ~SCB_STATUS_RNR;
Fixes: Covertiy CID 1419392 (commit 376b851909)
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
* get/set_uint cleanups (Felipe)
* Lock guard support (Stefan)
* MemoryRegion ownership cleanup (Philippe)
* AVX512 optimization for buffer_is_zero (Robert)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJecOZiAAoJEL/70l94x66DgGkH/jpY4IgqlSAAWCgaxfe1n1vg
ahSzSLrC8wiJq2Jxbmxn+5BbH6BxQ9ibflsY5bvCY/sTb7UlOFCPkFhQ2iUgplkw
ciB5UfgCA6OHpKEhpHhXtzlybtNOlxXNWYJ1SrcVXbRES8f7XdhMKs15mnJJuOOE
k/tuZo/44yZRJl0Cv+nkvIFcCVgyu1q0Lln/1MMPngY2r9gt893cY9feTBSSWgnp
+7HZr5TXI7mcIytczFKzbdujlG4391DGejKX66IIxGcWg9vXS7TwAStzH1vSKVfJ
73SKZBoCU5gpHHHC+dqVyouMerV+UE+WQPNtF+LCsNgJBw/2NXc1ZgDrtz1OI2c=
=+LRX
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* Bugfixes all over the place
* get/set_uint cleanups (Felipe)
* Lock guard support (Stefan)
* MemoryRegion ownership cleanup (Philippe)
* AVX512 optimization for buffer_is_zero (Robert)
# gpg: Signature made Tue 17 Mar 2020 15:01:54 GMT
# gpg: using RSA key BFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (62 commits)
hw/arm: Let devices own the MemoryRegion they create
hw/arm: Remove unnecessary memory_region_set_readonly() on ROM alias
hw/ppc/ppc405: Use memory_region_init_rom() with read-only regions
hw/arm/stm32: Use memory_region_init_rom() with read-only regions
hw/char: Let devices own the MemoryRegion they create
hw/riscv: Let devices own the MemoryRegion they create
hw/dma: Let devices own the MemoryRegion they create
hw/display: Let devices own the MemoryRegion they create
hw/core: Let devices own the MemoryRegion they create
scripts/cocci: Patch to let devices own their MemoryRegions
scripts/cocci: Patch to remove unnecessary memory_region_set_readonly()
scripts/cocci: Patch to detect potential use of memory_region_init_rom
hw/sparc: Use memory_region_init_rom() with read-only regions
hw/sh4: Use memory_region_init_rom() with read-only regions
hw/riscv: Use memory_region_init_rom() with read-only regions
hw/ppc: Use memory_region_init_rom() with read-only regions
hw/pci-host: Use memory_region_init_rom() with read-only regions
hw/net: Use memory_region_init_rom() with read-only regions
hw/m68k: Use memory_region_init_rom() with read-only regions
hw/display: Use memory_region_init_rom() with read-only regions
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit was produced with the Coccinelle script
scripts/coccinelle/memory-region-housekeeping.cocci.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The current code causes clang static code analyzer generate warning:
hw/net/imx_fec.c:858:9: warning: Value stored to 'value' is never read
value = value & 0x0000000f;
^ ~~~~~~~~~~~~~~~~~~
hw/net/imx_fec.c:864:9: warning: Value stored to 'value' is never read
value = value & 0x000000fd;
^ ~~~~~~~~~~~~~~~~~~
According to the definition of the function, the two “value” assignments
should be written to registers.
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Chen Qun <kuhn.chenqun@huawei.com>
Message-id: 20200313123242.13236-1-kuhn.chenqun@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Allwinner Sun8i System on Chip family includes an Ethernet MAC (EMAC)
which provides 10M/100M/1000M Ethernet connectivity. This commit
adds support for the Allwinner EMAC from the Sun8i family (H2+, H3, A33, etc),
including emulation for the following functionality:
* DMA transfers
* MII interface
* Transmit CRC calculation
Signed-off-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20200311221854.30370-10-nieklinnenbank@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Each array consumes 256KiB of .data. As we do not reassign entries,
we can move it to the .rodata section, and save a total of 1MiB of
.data (size reported on x86_64 host).
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Dmitry Fleytman <dmitry.fleytman@gmail.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20200305010446.17029-3-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
A portion of a recent patch got lost due to a merge snafu. That patch is
now commit 88f632fbb1 ("dp8393x: Mask EOL bit from descriptor addresses").
This patch restores the portion that got lost.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <alpine.LNX.2.22.394.2003041421280.12@nippy.intranet>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
When CADENCE_GEM_ERR_DEBUG is turned on, there are several
compilation errors in DB_PRINT(). Fix them.
While we are here, update to use appropriate modifiers in
the same DB_PRINT() call.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
When requested to calculate the hash for TCPV6 packet,
ignore overrides of source and destination addresses
in in extension headers.
Use these overrides when new hash type NetPktRssIpV6TcpEx
requested.
Use this type in e1000e hash calculation for IPv6 TCP, which
should take in account overrides of the addresses.
Signed-off-by: Yuri Benditovich <yuri.benditovich@daynix.com>
Acked-by: Dmitry Fleytman <dmitry.fleytman@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Add support for following hash types:
IPV6 TCP with extension headers
IPV4 UDP
IPV6 UDP
IPV6 UDP with extension headers
Signed-off-by: Yuri Benditovich <yuri.benditovich@daynix.com>
Acked-by: Dmitry Fleytman <dmitry.fleytman@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1787142
The emulation issues hw_error if PSRCTL register
is written, for example, with zero value.
Such configuration does not present any problem when
DTYP bits of RCTL register define legacy format of
transfer descriptors. Current commit discards check
for BSIZE0 and BSIZE1 when legacy mode used.
Acked-by: Dmitry Fleytman <dmitry.fleytman@gmail.com>
Signed-off-by: Yuri Benditovich <yuri.benditovich@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Section 3.4.7 of the datasheet explains that,
The RBE bit in the Interrupt Status register is set when the
SONIC finishes using the second to last receive buffer and reads
the last RRA descriptor. Actually, the SONIC is not truly out of
resources, but gives the system an early warning of an impending
out of resources condition.
RBE does not mean actual receive buffer exhaustion, and reception should
not be stopped. This is important because Linux will not check and clear
the RBE interrupt until it receives another packet. But that won't
happen if can_receive returns false. This bug causes the SONIC to become
deaf (until reset).
Fix this with a new flag to indicate actual receive buffer exhaustion.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The jazzsonic driver in Linux uses the Silicon Revision register value
to probe the chip. The driver fails unless the SR register contains 4.
Unfortunately, reading this register in QEMU usually returns 0 because
the s->regs[] array gets wiped after a software reset.
Fixes: bd8f1ebce4 ("net/dp8393x: fix hardware reset")
Suggested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jason Wang <jasowang@redhat.com>
These operations need to take place regardless of whether or not
rx descriptors have been used up (that is, EOL flag was observed).
The algorithm is now the same for a packet that was withheld as for
a packet that was not.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
When the SONIC receives a packet into the last available descriptor, it
retains ownership of that descriptor for as long as necessary.
Section 3.4.7 of the datasheet says,
When the system appends more descriptors, the SONIC releases ownership
of the descriptor after writing 0000h to the RXpkt.in_use field.
The packet can now be processed by the host, so raise a PKTRX interrupt,
just like the normal case.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The existing code has a bug where the Remaining Buffer Word Count (RBWC)
is calculated with a truncating division, which gives the wrong result
for odd-sized packets.
Section 1.4.1 of the datasheet says,
Once the end of the packet has been reached, the serializer will
fill out the last word (16-bit mode) or long word (32-bit mode)
if the last byte did not end on a word or long word boundary
respectively. The fill byte will be 0FFh.
Implement buffer padding so that buffer limits are correctly enforced.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Section 3.4.1 of the datasheet says,
The alignment of the RRA is confined to either word or long word
boundaries, depending upon the data width mode. In 16-bit mode,
the RRA must be aligned to a word boundary (A0 is always zero)
and in 32-bit mode, the RRA is aligned to a long word boundary
(A0 and A1 are always zero).
This constraint has been implemented for 16-bit mode; implement it
for 32-bit mode too.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
A received packet consumes pkt_size bytes in the buffer and the frame
checksum that's appended to it consumes another 4 bytes. The Receive
Buffer Address register takes the former quantity into account but
not the latter. So the next packet written to the buffer overwrites
the frame checksum. Fix this.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Add a bounds check to prevent a large packet from causing a buffer
overflow. This is defensive programming -- I haven't actually tried
sending an oversized packet or a jumbo ethernet frame.
The SONIC handles packets that are too big for the buffer by raising
the RBAE interrupt and dropping them. Linux uses that interrupt to
count dropped packets.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
It doesn't make sense to clear the command register bit unless the
command was actually issued.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Follow the algorithm given in the National Semiconductor DP83932C
datasheet in section 3.4.7:
At the next reception, the SONIC re-reads the last RXpkt.link field,
and updates its CRDA register to point to the next descriptor.
The chip is designed to allow the host to provide a new list of
descriptors in this way.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This function re-uses its 'size' argument as a scratch variable.
Instead, declare a local 'size' variable for that purpose so that the
function result doesn't get messed up.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
According to the datasheet, section 3.4.4, "in 32-bit mode ... the SONIC
always writes long words".
Therefore, use the same technique for the 'in_use' field that is used
everywhere else, and write the full long word.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The DP83932 and DP83934 have 32 data lines. The datasheet says,
Data Bus: These bidirectional lines are used to transfer data on the
system bus. When the SONIC is a bus master, 16-bit data is transferred
on D15-D0 and 32-bit data is transferred on D31-D0. When the SONIC is
accessed as a slave, register data is driven onto lines D15-D0.
D31-D16 are held TRI-STATE if SONIC is in 16-bit mode. If SONIC is in
32-bit mode, they are driven, but invalid.
Always use 32-bit accesses both as bus master and bus slave.
Force the MSW to zero in bus master mode.
This gets the Linux 'jazzsonic' driver working, and avoids the need for
prior hacks to make the NetBSD 'sn' driver work.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The Least Significant bit of a descriptor address register is used as
an EOL flag. It has to be masked when the register value is to be used
as an actual address for copying memory around. But when the registers
are to be updated the EOL bit should not be masked.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The address_space_rw() function allows either reads or writes
depending on the is_write argument passed to it; this is useful
when the direction of the access is determined programmatically
(as for instance when handling the KVM_EXIT_MMIO exit reason).
Under the hood it just calls either address_space_write() or
address_space_read_full().
We also use it a lot with a constant is_write argument, though,
which has two issues:
* when reading "address_space_rw(..., 1)" this is less
immediately clear to the reader as being a write than
"address_space_write(...)"
* calling address_space_rw() bypasses the optimization
in address_space_read() that fast-paths reads of a
fixed length
This commit was produced with the included Coccinelle script
scripts/coccinelle/exec_rw_const.cocci.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20200218112457.22712-1-peter.maydell@linaro.org>
[PMD: Update macvm_set_cr0() reported by Laurent Vivier]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Since its introduction in commit ac1970fbe8, address_space_rw()
takes a boolean 'is_write' argument. Fix the codebase by using
an explicit boolean type.
This commit was produced with the included Coccinelle script
scripts/coccinelle/exec_rw_const.
Inspired-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
This commit was produced with the included Coccinelle script
scripts/coccinelle/exec_rw_const.
Two lines in hw/net/dp8393x.c that Coccinelle produced that
were over 80 characters were re-wrapped by hand.
Suggested-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The NetReceive prototype gets a const buffer:
typedef ssize_t (NetReceive)(NetClientState *, const uint8_t *, size_t);
We already have the address_space_write() method to write a const
buffer to an address space. Use it to avoid:
hw/net/i82596.c: In function ‘i82596_receive’:
hw/net/i82596.c:644:54: error: passing argument 4 of ‘address_space_rw’ discards ‘const’ qualifier from pointer target type [-Werror=discarded-qualifiers]
This commit was produced with the included Coccinelle script
scripts/coccinelle/exec_rw_const.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Fix warnings reported by Clang static code analyzer:
CC hw/net/rocker/rocker.o
hw/net/rocker/rocker.c:213:9: warning: Value stored to 'tx_tso_mss' is never read
tx_tso_mss = rocker_tlv_get_le16(tlvs[ROCKER_TLV_TX_TSO_MSS]);
^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
hw/net/rocker/rocker.c:217:9: warning: Value stored to 'tx_tso_hdr_len' is never read
tx_tso_hdr_len = rocker_tlv_get_le16(tlvs[ROCKER_TLV_TX_TSO_HDR_LEN]);
^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
hw/net/rocker/rocker.c:255:9: warning: Value stored to 'tx_l3_csum_off' is never read
tx_l3_csum_off += tx_tso_mss = tx_tso_hdr_len = 0;
^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: dc488f888
Reported-by: Clang Static Analyzer
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20200217101637.27558-1-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
We have many files that apparently do not depend on the target CPU
configuration, i.e. which can be put into common-obj-y instead of
obj-y. This way, the code can be shared for example between
qemu-system-arm and qemu-system-aarch64, or the various big and
little endian variants like qemu-system-sh4 and qemu-system-sh4eb,
so that we do not have to compile the code multiple times anymore.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20200130133841.10779-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
These buffers should be aligned on 16 bytes.
Ignore invalid RX and TX buffer addresses and log an error. All
incoming and outgoing traffic will be dropped because no valid RX or
TX descriptors will be available.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20200114103433.30534-4-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
LASI is a built-in multi-I/O chip which supports serial, parallel,
network (Intel i82596 Apricot), sound and other functionalities.
LASI has been used in many HP PARISC machines.
This patch adds the necessary parts to allow Linux and HP-UX to detect
LASI and the network card.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20191220211512.3289-3-svens@stackframe.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We don't need to explicit these obvious switch fall through
comments. Stay consistent with the rest of the codebase.
Suggested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20191218192526.13845-6-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
GCC9 is confused by this comment when building with CFLAG
-Wimplicit-fallthrough=2:
hw/net/imx_fec.c: In function ‘imx_eth_write’:
hw/net/imx_fec.c:906:12: error: this statement may fall through [-Werror=implicit-fallthrough=]
906 | if (unlikely(single_tx_ring)) {
| ^
hw/net/imx_fec.c:912:5: note: here
912 | case ENET_TDAR: /* FALLTHROUGH */
| ^~~~
cc1: all warnings being treated as errors
Rewrite the comments in the correct place, using 'fall through'
which is recognized by GCC and static analyzers.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20191218192526.13845-5-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Define the new macro VMSTATE_INSTANCE_ID_ANY for callers who wants to
auto-generate the vmstate instance ID. Previously it was hard coded
as -1 instead of this macro. It helps to change this default value in
the follow up patches. No functional change.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
* Command line parsing fixes (Michal, Peter, Xiaoyao)
* Cooperlake CPU model fixes (Xiaoyao)
* i386 gdb fix (mkdolata)
* IOEventHandler cleanup (Philippe)
* icount fix (Pavel)
* RR support for random number sources (Pavel)
* Kconfig fixes (Philippe)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJeFbG8AAoJEL/70l94x66DCpMIAKBwxBL+VegqI+ySKgmtIBQX
LtU+ardEeZ37VfWfvuWzTFe+zQ0hsFpz/e0LHE7Ae+LVLMNWXixlmMrTIm+Xs762
hJzxBjhUhkdrMioVYTY16Kqap4Nqaxu70gDQ32Ve2sY6xYGxYLSaJooBOU5bXVgb
HPspHFVpeP6ZshBd1n2LXsgURE6v3AjTwqcsPCkL/AESFdkdOsoHeXjyKWJG1oPy
W7btzlUEqVsauZI8/PhhW/8hZUvUsJVHonYLTZTyy8aklU7aOILSyT2uPXFBVUVQ
irkQjLtD4dWlogBKO4i/QHMuwV+Asa57WNPmqv3EcIWPUWmTY84H0g2AxRgcc2M=
=48jx
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* Compat machines fix (Denis)
* Command line parsing fixes (Michal, Peter, Xiaoyao)
* Cooperlake CPU model fixes (Xiaoyao)
* i386 gdb fix (mkdolata)
* IOEventHandler cleanup (Philippe)
* icount fix (Pavel)
* RR support for random number sources (Pavel)
* Kconfig fixes (Philippe)
# gpg: Signature made Wed 08 Jan 2020 10:41:00 GMT
# gpg: using RSA key BFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (38 commits)
chardev: Use QEMUChrEvent enum in IOEventHandler typedef
chardev: use QEMUChrEvent instead of int
chardev/char: Explicit we ignore some QEMUChrEvent in IOEventHandler
monitor/hmp: Explicit we ignore a QEMUChrEvent in IOEventHandler
monitor/qmp: Explicit we ignore few QEMUChrEvent in IOEventHandler
virtio-console: Explicit we ignore some QEMUChrEvent in IOEventHandler
vhost-user-blk: Explicit we ignore few QEMUChrEvent in IOEventHandler
vhost-user-net: Explicit we ignore few QEMUChrEvent in IOEventHandler
vhost-user-crypto: Explicit we ignore some QEMUChrEvent in IOEventHandler
ccid-card-passthru: Explicit we ignore QEMUChrEvent in IOEventHandler
hw/usb/redirect: Explicit we ignore few QEMUChrEvent in IOEventHandler
hw/usb/dev-serial: Explicit we ignore few QEMUChrEvent in IOEventHandler
hw/char/terminal3270: Explicit ignored QEMUChrEvent in IOEventHandler
hw/ipmi: Explicit we ignore some QEMUChrEvent in IOEventHandler
hw/ipmi: Remove unnecessary declarations
target/i386: Add missed features to Cooperlake CPU model
target/i386: Add new bit definitions of MSR_IA32_ARCH_CAPABILITIES
target/i386: Fix handling of k_gs_base register in 32-bit mode in gdbstub
hw/rtc/mc146818: Add missing dependency on ISA Bus
hw/nvram/Kconfig: Restrict CHRP NVRAM to machines using OpenBIOS or SLOF
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Hi,
QDEV_PROP_PTR is marked in multiple places as "FIXME/TODO/remove
me". In most cases, it can be easily replaced with QDEV_PROP_LINK when
the pointer points to an Object.
There are a few places where such substitution isn't possible. For
those places, it seems reasonable to use a specific setter method
instead, and keep the user_creatable = false. In other places,
proper usage of qdev or other facilies is the solution.
The serial code wasn't converted to qdev, which makes it a bit more
archaic to deal with. Let's convert it first, so we can more easily
embed it from other devices, and re-export some properties and drop
QDEV_PROP_PTR usage.
-----BEGIN PGP SIGNATURE-----
iQJQBAABCAA6FiEEh6m9kz+HxgbSdvYt2ujhCXWWnOUFAl4UnUYcHG1hcmNhbmRy
ZS5sdXJlYXVAcmVkaGF0LmNvbQAKCRDa6OEJdZac5cfYEACcTfXklXdxLDj94Q5/
d6MxYqZWckO+vyMqOwonodl9BS3clpDDxbYzyfTpqwKS2cVg1eUUBPR7/eioX6zT
grM0rlgsKWJf9UurJwJWw7Zys7dXZMVJ2BdigLUEZrv9hFF15t344qoKgk4wYmBj
2wC7l7j2WZZ0vtXN7IH4/ZXnaN5/kdoPj6BrF0oNSJaq1AjPByQxmOJhvrxVsm6y
gn3la4XbfMIC68qPjcDJAScGXtCWG1Vydw9cFHwRpMfcvPyL70l6FMjIwrLYNQ9b
j1AkcEXeev5nWT+gLGxt+TGXB0Sd2ID9uRYxhyZRA4fdjHFtlWfdOwepOOlSlTO+
yfpf9STDLuDQGLTJyNZpYGGDDcm4xsJ8arD/7/Mq/35BQl9ZUT+m6uC1tDhxEHzf
+AD/Kh8rMptyAjwtqD2XbqyLoaFJCsPjZbjTj3SY08WaeqClmaAbSD2eaJiNXy4H
+rFg9P/eOB+71R1AoMKfiBFzdGV6TG5PLZOJ/oN02yqp0oW8eDWYcETB3j0tIgS1
u2WVCS2cd8IqYa+UQ7COOpoX0UwICmIWV64kxioD7uFQiK/1nQYw4UnPHv29qY6k
fTa8jUC5hPiDN1rRYqNpNoVJsstSZfSgpo5jV75sxSyDucupu+SM9qmo3+fBab+q
Eol3Ypz4virkNU8IYCYFFiG4Qg==
=iYVd
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/elmarco/tags/prop-ptr-pull-request' into staging
Clean-ups: qom-ify serial and remove QDEV_PROP_PTR
Hi,
QDEV_PROP_PTR is marked in multiple places as "FIXME/TODO/remove
me". In most cases, it can be easily replaced with QDEV_PROP_LINK when
the pointer points to an Object.
There are a few places where such substitution isn't possible. For
those places, it seems reasonable to use a specific setter method
instead, and keep the user_creatable = false. In other places,
proper usage of qdev or other facilies is the solution.
The serial code wasn't converted to qdev, which makes it a bit more
archaic to deal with. Let's convert it first, so we can more easily
embed it from other devices, and re-export some properties and drop
QDEV_PROP_PTR usage.
# gpg: Signature made Tue 07 Jan 2020 15:01:26 GMT
# gpg: using RSA key 87A9BD933F87C606D276F62DDAE8E10975969CE5
# gpg: issuer "marcandre.lureau@redhat.com"
# gpg: Good signature from "Marc-André Lureau <marcandre.lureau@redhat.com>" [full]
# gpg: aka "Marc-André Lureau <marcandre.lureau@gmail.com>" [full]
# Primary key fingerprint: 87A9 BD93 3F87 C606 D276 F62D DAE8 E109 7596 9CE5
* remotes/elmarco/tags/prop-ptr-pull-request: (37 commits)
qdev/qom: remove some TODO limitations now that PROP_PTR is gone
qdev: remove QDEV_PROP_PTR
qdev: remove PROP_MEMORY_REGION
omap-gpio: remove PROP_PTR
omap-i2c: remove PROP_PTR
omap-intc: remove PROP_PTR
smbus-eeprom: remove PROP_PTR
cris: improve passing PIC interrupt vector to the CPU
mips/cps: fix setting saar property
qdev: use g_strcmp0() instead of open-coding it
leon3: use qdev gpio facilities for the PIL
leon3: use qemu_irq framework instead of callback as property
dp8393x: replace PROP_PTR with PROP_LINK
etraxfs: remove PROP_PTR usage
lance: replace PROP_PTR with PROP_LINK
vmmouse: replace PROP_PTR with PROP_LINK
sm501: make SerialMM a child, export chardev property
mips: use sysbus_mmio_get_region() instead of internal fields
mips: use sysbus_add_io()
mips: baudbase is 115200 by default
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Bugfixes all over the place.
HMAT support.
New flags for vhost-user-blk utility.
Auto-tuning of seg max for virtio storage.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAl4TaMEPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpvzgH/2LyDAzCa9h93ikSJjmyUk5FUaqve38daEb3
S3JYjwKxQx7u1ydooKhvBQnBCZ2i3S+k62gfYyKB+nBv8xvjs0Eg5D1YJ5E8hciy
lf5OFGWWtX2iPDjZwQwT13kiJe0o3JRGxJJ6XqTEG+1EYOp7cky/FEv4PD030b9m
I2wROZ/Am+onB9YJX8c0Vv1CG+AryuJNXnvwQzTXEjj4U7bEYUyJwVZaCRyAdWQ3
uYXIZN9VwjVX6BFvy9ZAJbEsUVJvOM1/aQaDqcrLz+VlzRT7bRkKHi2G3vakrm1I
r5OpgyLo84132awCncbSykKDH5o8WaxLaJBjGmuBfasMz9wPzAg=
=uL1o
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio, pci, pc: fixes, features
Bugfixes all over the place.
HMAT support.
New flags for vhost-user-blk utility.
Auto-tuning of seg max for virtio storage.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Mon 06 Jan 2020 17:05:05 GMT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (32 commits)
intel_iommu: add present bit check for pasid table entries
intel_iommu: a fix to vtd_find_as_from_bus_num()
virtio-net: delete also control queue when TX/RX deleted
virtio: reset region cache when on queue deletion
virtio-mmio: update queue size on guest write
tests: add virtio-scsi and virtio-blk seg_max_adjust test
virtio: make seg_max virtqueue size dependent
hw: fix using 4.2 compat in 5.0 machine types for i440fx/q35
vhost-user-scsi: reset the device if supported
vhost-user: add VHOST_USER_RESET_DEVICE to reset devices
hw/pci/pci_host: Let pci_data_[read/write] use unsigned 'size' argument
hw/pci/pci_host: Remove redundant PCI_DPRINTF()
virtio-mmio: Clear v2 transport state on soft reset
ACPI: add expected files for HMAT tests (acpihmat)
tests/bios-tables-test: add test cases for ACPI HMAT
tests/numa: Add case for QMP build HMAT
hmat acpi: Build Memory Side Cache Information Structure(s)
hmat acpi: Build System Locality Latency and Bandwidth Information Structure(s)
hmat acpi: Build Memory Proximity Domain Attributes Structure(s)
numa: Extend CLI to provide memory side cache information
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Link property is the correct way to pass a MemoryRegion to a device
for DMA purposes.
Sidenote: as a sysbus device, this remains non-usercreatable
even though we can drop the specific flag here.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Tested-by: Laurent Vivier <laurent@vivier.eu>
etraxfs_dma_client are not Object, so can't be exposed to user with
QOM path. Let's remove property usage and move the constructor to the
.c unit, simplifying some code on the way.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
The device remains non-user creatable since it is a sysbus device.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The NMC93xx EEPROM is only used by few NIC cards and the
Am53C974 SCSI controller.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191231183216.6781-13-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1708480
If the control queue is not deleted together with TX/RX, it
later will be ignored in freeing cache resources and hot
unplug will not be completed.
Cc: qemu-stable@nongnu.org
Signed-off-by: Yuri Benditovich <yuri.benditovich@daynix.com>
Message-Id: <20191226043649.14481-3-yuri.benditovich@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Replace DeviceState dependency with VMStateIf on vmstate API.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
qemu_log_lock() now returns a handle and qemu_log_unlock() receives a
handle to unlock. This allows for changing the handle during logging
and ensures the lock() and unlock() are for the same file.
Also in target/tilegx/translate.c removed the qemu_log_lock()/unlock()
calls (and the log("\n")), since the translator can longjmp out of the
loop if it attempts to translate an instruction in an inaccessible page.
Signed-off-by: Robert Foley <robert.foley@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20191118211528.3221-5-robert.foley@linaro.org>
The script checkpatch.pl located in scripts folder was
used to detect all errors and warrnings in files:
hw/mips/mips_mipssim.c
hw/net/mipsnet.c
All these mips mipssim machine files were edited and
all the errors and warrings generated by the checkpatch.pl
script were corrected and then the script was
ran again to make sure there are no more errors and warnings.
Signed-off-by: Filip Bozuta <Filip.Bozuta@rt-rk.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <1575640687-20744-4-git-send-email-Filip.Bozuta@rt-rk.com>
The Aspeed MII model has a link pointing to its associated FTGMAC100
NIC in the machine.
Change the "nic" property definition so that it explicitly sets the
pointer. The property isn't optional : not being able to set the link
is a bug and QEMU should rather abort than exit in this case.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-18-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Functions that take an Error ** parameter to pass an error to the
caller expect the parameter to point to null.
failover_replug_primary() violates this precondition in several
places:
* After qemu_opts_from_qdict() failed, *errp is no longer null.
Passing it to error_setg() is wrong, and will trip the assertion in
error_setv(). Messed up in commit 150ab54aa6 "net/virtio: fix
re-plugging of primary device". Simply drop the error_setg().
* Passing @errp to qemu_opt_set_bool(), hotplug_handler_pre_plug(),
and hotplug_handler_plug() is wrong. If one of the first two fails,
*errp is no longer null. Risks tripping the same assertion.
Moreover, continuing after such errors is unsafe. Messed up in
commit 9711cd0dfc "net/virtio: add failover support". Fix by
handling each error properly.
failover_replug_primary() crashes when passed a null @errp. Also
messed up in commit 9711cd0dfc. This bug can't bite as no caller
actually passes null. Fix it anyway.
Fixes: 9711cd0dfc
Fixes: 150ab54aa6
Cc: Jens Freimann <jfreimann@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20191130194240.10517-3-armbru@redhat.com>
Reviewed-by: Jens Freimann <jfreimann@redhat.com>
virtio_net_handle_migration_primary() returns early when it can't
ensure n->primary_dev is non-null. Checking it again right after that
early return is redundant. Drop.
If n->primary_dev is null on entering failover_replug_primary(), @pdev
will become null, and pdev->partially_hotplugged will crash. Checking
n->primary_dev later is useless. It can't actually be null, because
its caller virtio_net_handle_migration_primary() ensures it isn't.
Drop the useless check.
Cc: Jens Freimann <jfreimann@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20191130194240.10517-2-armbru@redhat.com>
Reviewed-by: Jens Freimann <jfreimann@redhat.com>
This fixes CID 1407222.
Fixes: 9711cd0dfc ("net/virtio: add failover support")
Signed-off-by: Jens Freimann <jfreimann@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
failover_replug_primary was returning true on failure which lead to
re-plug not working when a migration failed. Fix this by returning
success when hotplug worked. This is a bug that was missed in last
round of testing but was tested succesfully with this version. Also
make sure we don't pass NULL to qdev_set_parent_bus().
This fixes CID 1407224.
Fixes: 9711cd0dfc ("net/virtio: add failover support")
Signed-off-by: Jens Freimann <jfreimann@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Bail out when primary device was already added before.
This avoids printing a wrong warning message during reboot.
Fixes: 9711cd0dfc ("net/virtio: add failover support")
Signed-off-by: Jens Freimann <jfreimann@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
.dev_unplug_pending is set up by virtio-net code indepent of failover
support was set for the device or not. This gives a wrong result when
we check for existing primary devices in migration code.
Fix this by actually calling dev_unplug_pending() instead of just
checking if the function pointer was set. When the feature was not
negotiated dev_unplug_pending() will always return false. This prevents
us from going into the wait-unplug state when there's no primary device
present.
Fixes: 9711cd0dfc ("net/virtio: add failover support")
Signed-off-by: Jens Freimann <jfreimann@redhat.com>
Reported-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The Linux kernel PHY driver sets AN_RESTART in the BMCR of the
PHY when autonegotiation is started.
Recently the kernel started to read back the PHY's AN_RESTART
bit and now checks whether the autonegotiation is complete and
the bit was cleared [1]. Otherwise the link status is down.
The emulated PHY needs to clear AN_RESTART immediately to inform
the kernel driver about the completion of autonegotiation phase.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=c36757eb9dee
Signed-off-by: Linus Ziegert <linus.ziegert+qemu@holoplot.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20191104181604.21943-1-linus.ziegert+qemu@holoplot.com
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
RXpkt.in_use is always 16 bit wide, but when the bus access mode is 32bit
and the endianness is big, we must access the second word and not the
first. This patch adjusts the offset according to the size and endianness.
This fixes DHCP for Q800 guest.
Fixes: be92084198 ("dp8393x: manage big endian bus")
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20191106112341.23735-3-laurent@vivier.eu>
Move it from the stack.
It's only 24 bytes, and this simplifies the dp8393x_get()/
dp8393x_put() interface.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20191106112341.23735-2-laurent@vivier.eu>
Use RCU_READ_LOCK_GUARD rather than the manual rcu_read_(un)lock call.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20191025103403.120616-3-dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch adds support to handle failover device pairs of a virtio-net
device and a (vfio-)pci device, where the virtio-net acts as the standby
device and the (vfio-)pci device as the primary.
The general idea is that we have a pair of devices, a (vfio-)pci and a
emulated (virtio-net) device. Before migration the vfio device is
unplugged and data flows to the emulated device, on the target side
another (vfio-)pci device is plugged in to take over the data-path. In the
guest the net_failover module will pair net devices with the same MAC
address.
To achieve this we need:
1. Provide a callback function for the should_be_hidden DeviceListener.
It is called when the primary device is plugged in. Evaluate the QOpt
passed in to check if it is the matching primary device. It returns
if the device should be hidden or not.
When it should be hidden it stores the device options in the VirtioNet
struct and the device is added once the VIRTIO_NET_F_STANDBY feature is
negotiated during virtio feature negotiation.
If the virtio-net devices are not realized at the time the (vfio-)pci
devices are realized, we need to connect the devices later. This way
we make sure primary and standby devices can be specified in any
order.
2. Register a callback for migration status notifier. When called it
will unplug its primary device before the migration happens.
3. Register a callback for the migration code that checks if a device
needs to be unplugged from the guest.
Signed-off-by: Jens Freimann <jfreimann@redhat.com>
Message-Id: <20191029114905.6856-11-jfreimann@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Version: GnuPG v1
iQEcBAABAgAGBQJdt6UAAAoJEO8Ells5jWIRdaAH/3+dufJuFijZY44VYbob92ud
lZR1dYah1fBL1bq0F2siFUb+/wgF1IXHJl9tuUJe8Kp0+hnsXji2s4Iuq5lNQoJj
wwMGziL1TPkhxwgy4jObIC+/bqZVrzAO4Cd+PARrSGAAbAqjxLPizOaf72/t4kdn
C2n87ZlR5k0EOPmUY6Y2DtHtrJ20usSS6EThGhdW7iPSzfQSGiOdRzfZrSiEV2XT
cuKbSzQxk7pbPcz4jIgLzaoA7FIXwm99dBosUkjPszNNFbO4+OPDNdUBanYuqmn/
0ZPe/9YZpEMV64ps/Ab7lx7YB04wZ+A9Etln2JULhBWXg/oyri9gsqgOc6bfCXg=
=uE5S
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jasowang/tags/net-pull-request' into staging
# gpg: Signature made Tue 29 Oct 2019 02:33:36 GMT
# gpg: using RSA key EF04965B398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>" [marginal]
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request:
COLO-compare: Fix incorrect `if` logic
virtio-net: prevent offloads reset on migration
virtio: new post_load hook
net: add tulip (dec21143) driver
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently offloads disabled by guest via the VIRTIO_NET_CTRL_GUEST_OFFLOADS_SET
command are not preserved on VM migration.
Instead all offloads reported by guest features (via VIRTIO_PCI_GUEST_FEATURES)
get enabled.
What happens is: first the VirtIONet::curr_guest_offloads gets restored and offloads
are getting set correctly:
#0 qemu_set_offload (nc=0x555556a11400, csum=1, tso4=0, tso6=0, ecn=0, ufo=0) at net/net.c:474
#1 virtio_net_apply_guest_offloads (n=0x555557701ca0) at hw/net/virtio-net.c:720
#2 virtio_net_post_load_device (opaque=0x555557701ca0, version_id=11) at hw/net/virtio-net.c:2334
#3 vmstate_load_state (f=0x5555569dc010, vmsd=0x555556577c80 <vmstate_virtio_net_device>, opaque=0x555557701ca0, version_id=11)
at migration/vmstate.c:168
#4 virtio_load (vdev=0x555557701ca0, f=0x5555569dc010, version_id=11) at hw/virtio/virtio.c:2197
#5 virtio_device_get (f=0x5555569dc010, opaque=0x555557701ca0, size=0, field=0x55555668cd00 <__compound_literal.5>) at hw/virtio/virtio.c:2036
#6 vmstate_load_state (f=0x5555569dc010, vmsd=0x555556577ce0 <vmstate_virtio_net>, opaque=0x555557701ca0, version_id=11) at migration/vmstate.c:143
#7 vmstate_load (f=0x5555569dc010, se=0x5555578189e0) at migration/savevm.c:829
#8 qemu_loadvm_section_start_full (f=0x5555569dc010, mis=0x5555569eee20) at migration/savevm.c:2211
#9 qemu_loadvm_state_main (f=0x5555569dc010, mis=0x5555569eee20) at migration/savevm.c:2395
#10 qemu_loadvm_state (f=0x5555569dc010) at migration/savevm.c:2467
#11 process_incoming_migration_co (opaque=0x0) at migration/migration.c:449
However later on the features are getting restored, and offloads get reset to
everything supported by features:
#0 qemu_set_offload (nc=0x555556a11400, csum=1, tso4=1, tso6=1, ecn=0, ufo=0) at net/net.c:474
#1 virtio_net_apply_guest_offloads (n=0x555557701ca0) at hw/net/virtio-net.c:720
#2 virtio_net_set_features (vdev=0x555557701ca0, features=5104441767) at hw/net/virtio-net.c:773
#3 virtio_set_features_nocheck (vdev=0x555557701ca0, val=5104441767) at hw/virtio/virtio.c:2052
#4 virtio_load (vdev=0x555557701ca0, f=0x5555569dc010, version_id=11) at hw/virtio/virtio.c:2220
#5 virtio_device_get (f=0x5555569dc010, opaque=0x555557701ca0, size=0, field=0x55555668cd00 <__compound_literal.5>) at hw/virtio/virtio.c:2036
#6 vmstate_load_state (f=0x5555569dc010, vmsd=0x555556577ce0 <vmstate_virtio_net>, opaque=0x555557701ca0, version_id=11) at migration/vmstate.c:143
#7 vmstate_load (f=0x5555569dc010, se=0x5555578189e0) at migration/savevm.c:829
#8 qemu_loadvm_section_start_full (f=0x5555569dc010, mis=0x5555569eee20) at migration/savevm.c:2211
#9 qemu_loadvm_state_main (f=0x5555569dc010, mis=0x5555569eee20) at migration/savevm.c:2395
#10 qemu_loadvm_state (f=0x5555569dc010) at migration/savevm.c:2467
#11 process_incoming_migration_co (opaque=0x0) at migration/migration.c:449
Fix this by preserving the state in saved_guest_offloads field and
pushing out offload initialization to the new post load hook.
Cc: qemu-stable@nongnu.org
Signed-off-by: Mikhail Sennikovsky <mikhail.sennikovskii@cloud.ionos.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This adds the basic functionality to emulate a Tulip NIC.
Implemented are:
- RX and TX functionality
- Perfect Frame Filtering
- Big/Little Endian descriptor support
- 93C46 EEPROM support
- LXT970 PHY
Not implemented, mostly because i had no OS using these functions:
- Imperfect frame filtering
- General Purpose Timer
- Transmit automatic polling
- Boot ROM support
- SIA interface
- Big/Little Endian data buffer conversion
Successfully tested with the following Operating Systems:
- MSDOS with Microsoft Network Client 3.0 and DEC ODI drivers
- HPPA Linux
- Windows XP
- HP-UX
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20191022155413.4619-1-svens@stackframe.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This is needed by Quadra 800, this card can run on little-endian
or big-endian bus.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20191026164546.30020-5-laurent@vivier.eu>
- iotest patches
- Improve performance of the mirror block job in write-blocking mode
- Limit memory usage for the backup block job
- Add discard and write-zeroes support to the NVMe host block driver
- Fix a bug in the mirror job
- Prevent the qcow2 driver from creating technically non-compliant qcow2
v3 images (where there is not enough extra data for snapshot table
entries)
- Allow callers of bdrv_truncate() (etc.) to determine whether the file
must be resized to the exact given size or whether it is OK for block
devices not to shrink
-----BEGIN PGP SIGNATURE-----
iQFGBAABCAAwFiEEkb62CjDbPohX0Rgp9AfbAGHVz0AFAl2224ESHG1yZWl0ekBy
ZWRoYXQuY29tAAoJEPQH2wBh1c9AeXMH/RXKEX4BZYMRKCe41P18tJC9Bl2x0T20
YeOsZVvpARlr7o/36BF2kGFF4MnL0OQ+9ELuyROX865rk/VL2rWqnHDE5oQM889a
dFwMs+0zvNbig3iLNcw0H5OkE2mrdM+a1EUdn/lBe/39Z8dPqPxRGqIYHq38Ugdu
emwSy1nWen7o0f71HRJfyVtI3KcrzXx71FrA/FY2yL/eHz+zRYGZj2SpAdFPkXP/
lgaz+m0tWhnSW1QzEOXB0Gh69ULt/DczCinYmv5qUY1noW5TPPtiDNCQTts5O4ba
oJsR3AJv5/l9m65JTmiyQSqnQfPcstrQ5FqOcSnP637cfqUFyWsvdks=
=L7v1
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/maxreitz/tags/pull-block-2019-10-28' into staging
Block patches for softfreeze:
- iotest patches
- Improve performance of the mirror block job in write-blocking mode
- Limit memory usage for the backup block job
- Add discard and write-zeroes support to the NVMe host block driver
- Fix a bug in the mirror job
- Prevent the qcow2 driver from creating technically non-compliant qcow2
v3 images (where there is not enough extra data for snapshot table
entries)
- Allow callers of bdrv_truncate() (etc.) to determine whether the file
must be resized to the exact given size or whether it is OK for block
devices not to shrink
# gpg: Signature made Mon 28 Oct 2019 12:13:53 GMT
# gpg: using RSA key 91BEB60A30DB3E8857D11829F407DB0061D5CF40
# gpg: issuer "mreitz@redhat.com"
# gpg: Good signature from "Max Reitz <mreitz@redhat.com>" [full]
# Primary key fingerprint: 91BE B60A 30DB 3E88 57D1 1829 F407 DB00 61D5 CF40
* remotes/maxreitz/tags/pull-block-2019-10-28: (69 commits)
qemu-iotests: restrict 264 to qcow2 only
Revert "qemu-img: Check post-truncation size"
block: Pass truncate exact=true where reasonable
block: Let format drivers pass @exact
block: Evaluate @exact in protocol drivers
block: Add @exact parameter to bdrv_co_truncate()
block: Do not truncate file node when formatting
block/cor: Drop cor_co_truncate()
block: Handle filter truncation like native impl.
iotests: Test qcow2's snapshot table handling
iotests: Add peek_file* functions
qcow2: Fix v3 snapshot table entry compliancy
qcow2: Repair snapshot table with too many entries
qcow2: Fix overly long snapshot tables
qcow2: Keep track of the snapshot table length
qcow2: Fix broken snapshot table entries
qcow2: Add qcow2_check_fix_snapshot_table()
qcow2: Separate qcow2_check_read_snapshot_table()
qcow2: Write v3-compliant snapshot list on upgrade
qcow2: Put qcow2_upgrade() into its own function
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
libqos update with support for virtio 1.
Packed ring support for virtio.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJdsuDvAAoJECgfDbjSjVRpIP8H/3rHSvZ5+MQGCFLI5GU8m3za
JSOaBSmtcj9KwrpibBfptSCJZNrG8EUVHyo+Z+pvGohXqDB8h9RyBfb6vID8jqzC
5wIzlNBP27F668MUBt2t7xSwK0PWO1QOpEKk6S4SJMpl51ea8ePlTH0jnLVfkaAN
hFKU1wqwc2gMyF9rDjOZ6I+OO1iQbMcrsazFrCXECXCkxDcJM0ey7MheKxVntTjt
0sxFHM2I1A+vXtAzlLo6rS3I9vJ0ATfLfOlZLqrq5uSAL5FKrqsbmGh4sAsFTQAA
eerR6zDz3X+YqfQaVgVk2wixPHQz2w8Rv68j6SiGrdZ29/JT6nVWHT8cGtPsX4c=
=iJuG
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio: features, tests
libqos update with support for virtio 1.
Packed ring support for virtio.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 25 Oct 2019 12:47:59 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (25 commits)
virtio: drop unused virtio_device_stop_ioeventfd() function
libqos: add VIRTIO PCI 1.0 support
libqos: extract Legacy virtio-pci.c code
libqos: make the virtio-pci BAR index configurable
libqos: expose common virtqueue setup/cleanup functions
libqos: add MSI-X callbacks to QVirtioPCIDevice
libqos: pass full QVirtQueue to set_queue_address()
libqos: add iteration support to qpci_find_capability()
libqos: access VIRTIO 1.0 vring in little-endian
libqos: implement VIRTIO 1.0 FEATURES_OK step
libqos: enforce Device Initialization order
libqos: add missing virtio-9p feature negotiation
tests/virtio-blk-test: set up virtqueue after feature negotiation
virtio-scsi-test: add missing feature negotiation
libqos: extend feature bits to 64-bit
libqos: read QVIRTIO_MMIO_VERSION register
tests/virtio-blk-test: read config space after feature negotiation
virtio: add property to enable packed virtqueue
vhost_net: enable packed ring support
virtio: event suppression support for packed ring
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
endof() is a useful macro, we can make use of it outside of virtio.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20191011152814.14791-2-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Reviewed-by: Jens Freimann <jfreimann@redhat.com>
Message-Id: <20191025083527.30803-8-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Switch the fsl_etsec code away from bottom-half based ptimers to
the new transaction-based ptimer API. This just requires adding
begin/commit calls around the various places that modify the ptimer
state, and using the new ptimer_init() function to create the timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20191017132122.4402-2-peter.maydell@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2600 SoC has an extra controller to set the PHY registers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-23-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Switch the cmsdk-apb-watchdog code away from bottom-half based
ptimers to the new transaction-based ptimer API. This just requires
adding begin/commit calls around the various places that modify the
ptimer state, and using the new ptimer_init() function to create the
timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-22-peter.maydell@linaro.org
Currently the ptimer design uses a QEMU bottom-half as its
mechanism for calling back into the device model using the
ptimer when the timer has expired. Unfortunately this design
is fatally flawed, because it means that there is a lag
between the ptimer updating its own state and the device
callback function updating device state, and guest accesses
to device registers between the two can return inconsistent
device state.
We want to replace the bottom-half design with one where
the guest device's callback is called either immediately
(when the ptimer triggers by timeout) or when the device
model code closes a transaction-begin/end section (when the
ptimer triggers because the device model changed the
ptimer's count value or other state). As the first step,
rename ptimer_init() to ptimer_init_with_bh(), to free up
the ptimer_init() name for the new API. We can then convert
all the ptimer users away from ptimer_init_with_bh() before
removing it entirely.
(Commit created with
git grep -l ptimer_init | xargs sed -i -e 's/ptimer_init/ptimer_init_with_bh/'
and three overlong lines folded by hand.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-2-peter.maydell@linaro.org
Every caller of spapr_vio_qirq() immediately calls qemu_irq_pulse() with
the result, so we might as well just fold that into the helper.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Commit 78dd48df3 reworked vmxnet3's live migration but left a straggling
unregister_savevm call. Remove it, although it doesn't seem to have
any bad effect.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20190822111218.12079-1-dgilbert@redhat.com>
Reviewed-by: Dmitry Fleytman <dmitry.fleytman@gmail.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
As explained in commit aff39be0ed:
Both functions, object_initialize() and object_property_add_child()
increase the reference counter of the new object, so one of the
references has to be dropped afterwards to get the reference
counting right. Otherwise the child object will not be properly
cleaned up when the parent gets destroyed.
Thus let's use now object_initialize_child() instead to get the
reference counting here right.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190823143249.8096-7-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Missed during the QOM convertion in 9af21dbee1.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20190715102210.31365-1-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
* target/arm: generate a custom MIDR for -cpu max
* hw/misc/zynq_slcr: refactor to use standard register definition
* Set ENET_BD_BDU in I.MX FEC controller
* target/arm: Fix routing of singlestep exceptions
* refactor a32/t32 decoder handling of PC
* minor optimisations/cleanups of some a32/t32 codegen
* target/arm/cpu64: Ensure kvm really supports aarch64=off
* target/arm/cpu: Ensure we can use the pmu with kvm
* target/arm: Minor cleanups preparatory to KVM SVE support
-----BEGIN PGP SIGNATURE-----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=8BAF
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20190816' into staging
target-arm queue:
* target/arm: generate a custom MIDR for -cpu max
* hw/misc/zynq_slcr: refactor to use standard register definition
* Set ENET_BD_BDU in I.MX FEC controller
* target/arm: Fix routing of singlestep exceptions
* refactor a32/t32 decoder handling of PC
* minor optimisations/cleanups of some a32/t32 codegen
* target/arm/cpu64: Ensure kvm really supports aarch64=off
* target/arm/cpu: Ensure we can use the pmu with kvm
* target/arm: Minor cleanups preparatory to KVM SVE support
# gpg: Signature made Fri 16 Aug 2019 14:15:55 BST
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20190816: (29 commits)
target/arm: Use tcg_gen_extrh_i64_i32 to extract the high word
target/arm: Simplify SMMLA, SMMLAR, SMMLS, SMMLSR
target/arm: Use tcg_gen_rotri_i32 for gen_swap_half
target/arm: Use ror32 instead of open-coding the operation
target/arm: Remove redundant shift tests
target/arm: Use tcg_gen_deposit_i32 for PKHBT, PKHTB
target/arm: Use tcg_gen_extract_i32 for shifter_out_im
target/arm/kvm64: Move the get/put of fpsimd registers out
target/arm/kvm64: Fix error returns
target/arm/cpu: Use div-round-up to determine predicate register array size
target/arm/helper: zcr: Add build bug next to value range assumption
target/arm/cpu: Ensure we can use the pmu with kvm
target/arm/cpu64: Ensure kvm really supports aarch64=off
target/arm: Remove helper_double_saturate
target/arm: Use unallocated_encoding for aarch32
target/arm: Remove offset argument to gen_exception_bkpt_insn
target/arm: Replace offset with pc in gen_exception_internal_insn
target/arm: Replace offset with pc in gen_exception_insn
target/arm: Replace s->pc with s->base.pc_next
target/arm: Remove redundant s->pc & ~1
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----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=eSUz
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/armbru/tags/pull-include-2019-08-13-v2' into staging
Header cleanup patches for 2019-08-13
# gpg: Signature made Fri 16 Aug 2019 12:39:12 BST
# gpg: using RSA key 354BC8B3D7EB2A6B68674E5F3870B400EB918653
# gpg: issuer "armbru@redhat.com"
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>" [full]
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>" [full]
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-include-2019-08-13-v2: (29 commits)
sysemu: Split sysemu/runstate.h off sysemu/sysemu.h
sysemu: Move the VMChangeStateEntry typedef to qemu/typedefs.h
Include sysemu/sysemu.h a lot less
Clean up inclusion of sysemu/sysemu.h
numa: Move remaining NUMA declarations from sysemu.h to numa.h
Include sysemu/hostmem.h less
numa: Don't include hw/boards.h into sysemu/numa.h
Include hw/boards.h a bit less
Include hw/qdev-properties.h less
Include qemu/main-loop.h less
Include qemu/queue.h slightly less
Include hw/hw.h exactly where needed
Include qom/object.h slightly less
Include exec/memory.h slightly less
Include migration/vmstate.h less
migration: Move the VMStateDescription typedef to typedefs.h
Clean up inclusion of exec/cpu-common.h
Include hw/irq.h a lot less
typedefs: Separate incomplete types and function types
ide: Include hw/ide/internal a bit less outside hw/ide/
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit properly sets the ENET_BD_BDU flag once the emulated FEC controller
has finished processing the last descriptor. This is done for both transmit
and receive descriptors.
This allows the QNX 7.0.0 BSP for the Sabrelite board (which can be
found at http://blackberry.qnx.com/en/developers/bsp) to properly
control the FEC. Without this patch, the BSP ethernet driver will never
re-use FEC descriptors, as the unset ENET_BD_BDU flag will cause
it to believe that the descriptors are still in use by the NIC.
Note that Linux does not appear to use this field at all, and is
unaffected by this patch.
Without this patch, QNX will think that the NIC is still processing its
transaction descriptors, and won't send any more data over the network.
For reference:
On page 1192 of the I.MX 6DQ reference manual revision (Rev. 5, 06/2018),
which can be found at https://www.nxp.com/products/processors-and-microcontrollers/arm-based-processors-and-mcus/i.mx-applications-processors/i.mx-6-processors/i.mx-6quad-processors-high-performance-3d-graphics-hd-video-arm-cortex-a9-core:i.MX6Q?&tab=Documentation_Tab&linkline=Application-Note
the 'BDU' field is described as follows for the 'Enhanced transmit
buffer descriptor':
'Last buffer descriptor update done. Indicates that the last BD data has been updated by
uDMA. This field is written by the user (=0) and uDMA (=1).'
The same description is used for the receive buffer descriptor.
Signed-off-by: Aaron Hill <aa1ronham@gmail.com>
Message-id: 20190805142417.10433-1-aaron.hill@alertinnovation.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
sysemu/sysemu.h is a rather unfocused dumping ground for stuff related
to the system-emulator. Evidence:
* It's included widely: in my "build everything" tree, changing
sysemu/sysemu.h still triggers a recompile of some 1100 out of 6600
objects (not counting tests and objects that don't depend on
qemu/osdep.h, down from 5400 due to the previous two commits).
* It pulls in more than a dozen additional headers.
Split stuff related to run state management into its own header
sysemu/runstate.h.
Touching sysemu/sysemu.h now recompiles some 850 objects. qemu/uuid.h
also drops from 1100 to 850, and qapi/qapi-types-run-state.h from 4400
to 4200. Touching new sysemu/runstate.h recompiles some 500 objects.
Since I'm touching MAINTAINERS to add sysemu/runstate.h anyway, also
add qemu/main-loop.h.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-30-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
[Unbreak OS-X build]
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 1800 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h, down from 5400 due to the
previous commit).
Several headers include sysemu/sysemu.h just to get typedef
VMChangeStateEntry. Move it from sysemu/sysemu.h to qemu/typedefs.h.
Spell its structure tag the same while there. Drop the now
superfluous includes of sysemu/sysemu.h from headers.
Touching sysemu/sysemu.h now recompiles some 1100 objects.
qemu/uuid.h also drops from 1800 to 1100, and
qapi/qapi-types-run-state.h from 5000 to 4400.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-29-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 5400 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Almost a third of its inclusions are actually superfluous. Delete
them. Downgrade two more to qapi/qapi-types-run-state.h, and move one
from char/serial.h to char/serial.c.
hw/semihosting/config.c, monitor/monitor.c, qdev-monitor.c, and
stubs/semihost.c define variables declared in sysemu/sysemu.h without
including it. The compiler is cool with that, but include it anyway.
This doesn't reduce actual use much, as it's still included into
widely included headers. The next commit will tackle that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-27-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
In my "build everything" tree, changing qemu/main-loop.h triggers a
recompile of some 5600 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h). It includes block/aio.h,
which in turn includes qemu/event_notifier.h, qemu/notify.h,
qemu/processor.h, qemu/qsp.h, qemu/queue.h, qemu/thread-posix.h,
qemu/thread.h, qemu/timer.h, and a few more.
Include qemu/main-loop.h only where it's needed. Touching it now
recompiles only some 1700 objects. For block/aio.h and
qemu/event_notifier.h, these numbers drop from 5600 to 2800. For the
others, they shrink only slightly.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-21-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/hw.h triggers a recompile
of some 2600 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
The previous commits have left only the declaration of hw_error() in
hw/hw.h. This permits dropping most of its inclusions. Touching it
now recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-19-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Drop unnecessary inclusions from headers. Downgrade a few more to
exec/hwaddr.h.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-17-armbru@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/irq.h triggers a recompile
of some 5400 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get qemu_irq and.or qemu_irq_handler.
Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed. Touching it now recompiles only some 500 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-13-armbru@redhat.com>
In my "build everything" tree, changing sysemu/reset.h triggers a
recompile of some 2600 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
The main culprit is hw/hw.h, which supposedly includes it for
convenience.
Include sysemu/reset.h only where it's needed. Touching it now
recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-9-armbru@redhat.com>
TYPE_IOMMU_MEMORY_REGION is a direct subtype of TYPE_MEMORY_REGION.
Its instance struct is IOMMUMemoryRegion, and its first member is a
MemoryRegion. Correct. Its class struct is IOMMUMemoryRegionClass,
and its first member is a DeviceClass. Wrong. Messed up when commit
1221a47467 introduced the QOM type. It even included hw/qdev-core.h
just for that.
TYPE_MEMORY_REGION doesn't bother to define a class struct. This is
fine, it simply defaults to its super-type TYPE_OBJECT's class struct
ObjectClass. Changing IOMMUMemoryRegionClass's first member's type to
ObjectClass would be a minimal fix, if a bit brittle: if
TYPE_MEMORY_REGION ever acquired own class struct, we'd have to update
IOMMUMemoryRegionClass to use it.
Fix it the clean and robust way instead: give TYPE_MEMORY_REGION its
own class struct MemoryRegionClass now, and use it for
IOMMUMemoryRegionClass's first member.
Revert the include of hw/qdev-core.h, and fix the few files that have
come to rely on it.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20190812052359.30071-5-armbru@redhat.com>
At some point vmxnet3 live migration stopped working and git-bisect
didn't help finding a working version.
The issue is the PCI configuration space is not being migrated
successfully and MSIX remains masked at destination.
Remove the migration differentiation between PCI and PCIe since
the logic resides now inside VMSTATE_PCI_DEVICE.
Remove also the VMXNET3_COMPAT_FLAG_DISABLE_PCIE based differentiation
since at 'realize' time is decided if the device is PCI or PCIe,
then the above macro is enough.
Use the opportunity to move to the standard VMSTATE_MSIX
instead of the deprecated SaveVMHandlers.
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Message-Id: <20190705010711.23277-1-marcel.apfelbaum@gmail.com>
Tested-by: Sukrit Bhatnagar <skrtbhtngr@gmail.com>
Reviewed-by: Dmitry Fleytman <dmitry.fleytman@gmail.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
We should not raise any interrupt after VM has been stopped but this
is what e1000 currently did when mit timer is active in
pre_save(). Fixing this by scheduling a timer in post_load() which can
make sure the interrupt was raised when VM is running.
Reported-and-tested-by: Longpeng <longpeng2@huawei.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
On very busy networks connected via a tap interface, it is possible to overflow
the RX descriptor ring in the time between the client driver enabling the RX
MAC and finishing writing the final configuration to the NIC registers.
Ensure that we detect this condition and update the status register accordingly
to indicate an overflow has occurred (and the incoming packet dropped) in order
to prevent the client driver becoming confused.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The current return values in sunhme_receive() when processing incoming packets
are inverted from what they should be. Make sure that we return 0 to indicate
the packet was discarded (and polling is to be disabled) and -1 to indicate
that the packet was discarded but polling for incoming data is to be continued.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Some client drivers use this bit to pause and resume the driver so make sure
that queued packets are flushed when the MAC is disabled and then reactivated.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Due to a copy/paste error the wrong register was being checked in order to
determine if the NIC is able to receive data.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Previously there was a single instance of the timer used by
monitor triggered announces, that's OK, but when combined with the
previous change that lets you have announces for subsets of interfaces
it's a bit restrictive if you want to do different things to different
interfaces.
Add an 'id' field to the announce, and maintain a list of the
timers based on id.
This allows you to for example:
a) Start an announce going on interface eth0 for a long time
b) Start an announce going on interface eth1 for a long time
c) Kill the announce on eth0 while leaving eth1 going.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
qdev_set_nic_properties() is already used in the Aspeed SoC level to
bind the ftgmac100 device to the netdev.
This is fixing support for multiple net devices.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
A Xen public header have been imported into QEMU (by
f65eadb639 "xen: import ring.h from xen"), but there are other header
that depends on ring.h which come from the system when building QEMU.
This patch resolves the issue of having headers from the system
importing a different copie of ring.h.
This patch is prompt by the build issue described in the previous
patch: 'Revert xen/io/ring.h of "Clean up a few header guard symbols"'
ring.h and the new imported headers are moved to
"include/hw/xen/interface" as those describe interfaces with a guest.
The imported headers are cleaned up a bit while importing them: some
part of the file that QEMU doesn't use are removed (description
of how to make hypercall in grant_table.h have been removed).
Other cleanup:
- xen-mapcache.c and xen-legacy-backend.c don't need grant_table.h.
- xenfb.c doesn't need event_channel.h.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Message-Id: <20190621105441.3025-3-anthony.perard@citrix.com>
No header includes qemu-common.h after this commit, as prescribed by
qemu-common.h's file comment.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190523143508.25387-5-armbru@redhat.com>
[Rebased with conflicts resolved automatically, except for
include/hw/arm/xlnx-zynqmp.h hw/arm/nrf51_soc.c hw/arm/msf2-soc.c
block/qcow2-refcount.c block/qcow2-cluster.c block/qcow2-cache.c
target/arm/cpu.h target/lm32/cpu.h target/m68k/cpu.h target/mips/cpu.h
target/moxie/cpu.h target/nios2/cpu.h target/openrisc/cpu.h
target/riscv/cpu.h target/tilegx/cpu.h target/tricore/cpu.h
target/unicore32/cpu.h target/xtensa/cpu.h; bsd-user/main.c and
net/tap-bsd.c fixed up]
"megasas: fix mapped frame size" from Peter Lieven.
In addition, -realtime is marked as deprecated.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJc3rY3AAoJEL/70l94x66D91kH/21LLnL+sKmyueSM/Sek4id2
r06tHdGMdl5Od3I5uMD9gnr4AriiCZc9ybQDQ1N879wKMmQPZwcnf2GJ5DZ0wa3L
jHoQO07Bg0KZGWALjXiN5PWB0DlJtXsTm0C4q4tnt6V/ueasjxouBk9/fRLRc09n
QTS379X9QvPElFTv3WPfGz6kmkLq8VMmdRnSlXneB9xTyXXJbFj3zlvDCElNSgWh
fZ7gnfYWB1LOC19HJxp1mJSkAUD5AgImYEK1Hmnr+BMs2sg6gypYNtp3LtE5FzmZ
HSdXYFyPkQV9UyTiV1XBs3bXJbGYj5OApfXCtwo/I2JtP+LhHBA2eq1Gs3QgP98=
=zSSj
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
Mostly bugfixes and cleanups, the most important being
"megasas: fix mapped frame size" from Peter Lieven.
In addition, -realtime is marked as deprecated.
# gpg: Signature made Fri 17 May 2019 14:25:11 BST
# gpg: using RSA key BFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (21 commits)
hw/net/ne2000: Extract the PCI device from the chipset common code
hw/char: Move multi-serial devices into separate file
ioapic: allow buggy guests mishandling level-triggered interrupts to make progress
build: don't build hardware objects with linux-user
build: chardev is only needed for softmmu targets
configure: qemu-ga is only needed with softmmu targets
build: replace GENERATED_FILES by generated-files-y
trace: only include trace-event-subdirs when they are needed
sun4m: obey -vga none
mips-fulong2e: obey -vga none
hw/i386/acpi: Assert a pointer is not null BEFORE using it
hw/i386/acpi: Add object_resolve_type_unambiguous to improve modularity
hw/acpi/piix4: Move TYPE_PIIX4_PM to a public header
memory: correct the comment to DIRTY_MEMORY_MIGRATION
vl: fix -sandbox parsing crash when seccomp support is disabled
hvf: Add missing break statement
megasas: fix mapped frame size
vl: Add missing descriptions to the VGA adapters list
Declare -realtime as deprecated
roms: assert if max rom size is less than the used size
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ne2000.c file contains functions common the the ISA and PCI
devices. To allow to build with one or another, extract the PCI
specific part into a new file.
This fix an issue where the NE2000_ISA Kconfig had to pull the
full PCI core objects.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190504123538.14952-1-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In situations where e1000 receives an undersized Ethernet frame,
QEMU increments the emulated "Receive Undersize Count (RUC)"
register when padding the frame.
This is incorrect because this an expected scenario (e.g. with
VLAN tag stripping) and not an error. As such, QEMU should not
increment the emulated RUC.
Fixes: 3b27430177 ("e1000: Implementing various counters")
Reviewed-by: Mark Kanda <mark.kanda@oracle.com>
Reviewed-by: Bhavesh Davda <bhavesh.davda@oracle.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Chris Kenna <chris.kenna@oracle.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
We used to set backend unconditionally, this won't work for some
guests (e.g windows driver) who may not initialize all virtqueues. For
kernel backend, this will fail since it may try to validate the rings
during setting backend.
Fixing this by simply skipping the backend set when we find desc is
not ready.
Reviewed-by: Michael S. Tsirkin<mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This commit finally deletes "hw/devices.h".
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-13-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-12-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-10-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Message-Id: <20190321161832.10533-1-yuval.shaia@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Some trace points are attributed to the wrong source file. Happens
when we neglect to update trace-events for code motion, or add events
in the wrong place, or misspell the file name.
Clean up with help of cleanup-trace-events.pl. Same funnies as in the
previous commit, of course. Manually shorten its change to
linux-user/trace-events to */signal.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-id: 20190314180929.27722-6-armbru@redhat.com
Message-Id: <20190314180929.27722-6-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We spell out sub/dir/ in sub/dir/trace-events' comments pointing to
source files. That's because when trace-events got split up, the
comments were moved verbatim.
Delete the sub/dir/ part from these comments. Gets rid of several
misspellings.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190314180929.27722-3-armbru@redhat.com
Message-Id: <20190314180929.27722-3-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
For devices that require msi_init/msix_init to succeed, add a
dependency on CONFIG_MSI_NONBROKEN. This will prevent those devices
from appearing in a binary that cannot instantiate them.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The qemu coding standard is to use CamelCase for type and structure names,
and the pseries code follows that... sort of. There are quite a lot of
places where we bend the rules in order to preserve the capitalization of
internal acronyms like "PHB", "TCE", "DIMM" and most commonly "sPAPR".
That was a bad idea - it frequently leads to names ending up with hard to
read clusters of capital letters, and means they don't catch the eye as
type identifiers, which is kind of the point of the CamelCase convention in
the first place.
In short, keeping type identifiers look like CamelCase is more important
than preserving standard capitalization of internal "words". So, this
patch renames a heap of spapr internal type names to a more standard
CamelCase.
In addition to case changes, we also make some other identifier renames:
VIOsPAPR* -> SpaprVio*
The reverse word ordering was only ever used to mitigate the capital
cluster, so revert to the natural ordering.
VIOsPAPRVTYDevice -> SpaprVioVty
VIOsPAPRVLANDevice -> SpaprVioVlan
Brevity, since the "Device" didn't add useful information
sPAPRDRConnector -> SpaprDrc
sPAPRDRConnectorClass -> SpaprDrcClass
Brevity, and makes it clearer this is the same thing as a "DRC"
mentioned in many other places in the code
This is 100% a mechanical search-and-replace patch. It will, however,
conflict with essentially any and all outstanding patches touching the
spapr code.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This will make it for example easier if the users want to disable
one of the two machines for their builds.
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-42-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
