BAR base was calculated incorrectly.
Use existing pci_bar_address to get it right.
Tested-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Instead of exposing the the irq field,
pci wrappers to qemu_set_irq or qemu_irq_*
can be used.
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The fields hpev_intx and aer_intx were removed because
both AER and hot-plug events must use device's interrupt.
Assert/deassert interrupts using pci irq wrappers instead.
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
pci_set_irq and the other pci irq wrappers use
PCI_INTERRUPT_PIN config register to compute device
INTx pin to assert/deassert.
An irq is allocated using pci_allocate_irq wrapper
only if is needed by non pci devices.
Removed irq related fields from state if not used anymore.
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Interrupt pin is selected and saved into PCI_INTERRUPT_PIN
register during device initialization. Devices should not call
directly qemu_set_irq and specify the INTx pin on each call.
Added pci_* wrappers to replace qemu_set_irq, qemu_irq_raise,
qemu_irq_lower and qemu_irq_pulse, setting the irq
based on PCI_INTERRUPT_PIN.
Added pci_allocate_irq wrapper to be used by devices that
still need PCIDevice infrastructure to assert irqs.
Renamed a static method which was named already pci_set_irq.
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A MemoryRegion with negative priority was created and
it spans over all the pci address space.
It "intercepts" the accesses to unassigned pci
address space and will follow the pci spec:
1. returns -1 on read
2. does nothing on write
Note: setting the RECEIVED MASTER ABORT bit in the STATUS register
of the device that initiated the transaction will be
implemented in another series
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This check is useless, as bigger addresses will be ignored when
added to 'io' MemoryRegion, which has a size of 64K.
However, some architectures don't use the 'io' MemoryRegion, like
the alpha and versatile platforms. They create a PCI I/O region
bigger than 64K, so let them handle PCI I/O BARs in the higher range.
MST: reinstated work-around for BAR sizing.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add c++ keywords to avoid errors in compiling with c++ compiler.
This also renames class member of PciDeviceInfo to q_class.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@hds.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
This includes pc and pci cleanups and enhancements,
and a virtio bugfix for level interrupts.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJSIveoAAoJECgfDbjSjVRp2C8IAL7DE0oM0jfEB5DAd8jlULHx
hA8RP21rFzyU8PwtHB+72+C1ImldBge4hvhI+qbsm6PoW3RCeV/lbESIRTiv8dCO
pGUOFmv8MfJAH+WWFsle5mRisoTksYQWWBMHCOqvmaY4JL9pBQOhCLHVhV1XfjtL
hO7uGrWmlijeILv5CxYyPMYuOEdVvRSZKzE+Fp2YKfNstiQrS5fJIlqmwCHrlneW
l2atnt2d9ZV1K8QYiGg4GRVbSAMJvA1wum+0F4gnXIz9yAeOt+Ht1s8cNKQDMouJ
r2OyVgPM9aS/XaO6ejct1Sjo7Vgh/Ublrpw3lFqV/qHix6rEHwy2I3JHFEJPjvk=
=SytJ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mst/tags/for_anthony' into staging
pc,pci,virtio fixes and cleanups
This includes pc and pci cleanups and enhancements,
and a virtio bugfix for level interrupts.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Sun 01 Sep 2013 03:15:36 AM CDT using RSA key ID D28D5469
# gpg: Can't check signature: public key not found
# By Michael S. Tsirkin (3) and others
# Via Michael S. Tsirkin
* mst/tags/for_anthony:
virtio_pci: fix level interrupts with irqfd
pc: reduce duplication, fix PIIX descriptions
hw: Clean up bogus default boot order
pci: add config space access traces
pc: fix regression for 64 bit PCI memory
pci: Introduce helper to retrieve a PCI device's DMA address space
Message-id: 1378023590-11109-1-git-send-email-mst@redhat.com
Signed-off-by: Anthony Liguori <anthony@codemonkey.ws>
To be passed to object_initialize().
Since commit 39355c3826 the argument is
void*, so drop some superfluous (BusState *) casts or direct parent
field usages.
Signed-off-by: Andreas Färber <afaerber@suse.de>
This adds pci_cfg_read and pci_cfg_write traces for config spaces
accesses.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A PCI device's DMA address space (possibly an IOMMU) is returned by a
method on the PCIBus. At the moment that only has one caller, so the
method is simply open coded. We'll need another caller for VFIO, so
this patch introduces a helper/wrapper function.
If IOMMU is not set, the pci_device_iommu_address_space() function
returns the parent's IOMMU skipping the "bus master" address space as
otherwise proper emulation would require more effort for no benefit.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
[aik: added inheritance from parent if iommu is not set for the current bus]
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Move PCIEPort's "port" property to the new type, same for "aer_log_max".
Move PCIESlot's "chassis" and "slot" properties to the new type.
Reviewed-by: Don Koch <dkoch@verizon.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Introduce TYPE_PCI_BRIDGE as base type and use PCI_BRIDGE() casts.
Reviewed-by: Don Koch <dkoch@verizon.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
[AF: Updated pbm-bridge parent to TYPE_PCI_BRIDGE]
Signed-off-by: Andreas Färber <afaerber@suse.de>
Let scsi_bus_legacy_add_drive() and scsi_bus_legacy_handle_cmdline()
return an Error**. Prepare qdev initfns for QOM realize error model.
Signed-off-by: Andreas Färber <afaerber@suse.de>
This includes some fixes and enhancements that accumulated in my tree:
pci fixes by dkoch, virtio-net enhancements by akong and mst,
and a fix for xen pc by mst.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQEcBAABAgAGBQJR5meNAAoJECgfDbjSjVRp24IIAMOkxbb85FJ323G/x5cQBzA/
gjFDmvB6geIMBorX1YZRnIM+RFhx+mkXtBTu2raWVTNTt5G2u3vAQQWW2zSiOTBL
gH4BhzJnUoqLHOydWql2MsGS7DMQo4Fq8OnzRBkZ119AEEqNMad1w2LykwFWs4ra
k3bsPNCZM+ZNiLMWtQLOcD3FYvoiISinqFd81KOnxvDiT90rczk4dLWqjv8smNif
WqZ7aCD1hGJ5yD7JI2YjCbhVvu4F7tBK+fWkT/O3oYslh/o241lyxUriOXMKdKML
04sNXa5eWue9cOKlbo1G+yfFwFg1JDsAMe/Usg0KXz1MMK91wiWE763ESPbFBK0=
=P+pr
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mst/tags/for_anthony' into staging
pci,net,pc enhancements
This includes some fixes and enhancements that accumulated in my tree:
pci fixes by dkoch, virtio-net enhancements by akong and mst,
and a fix for xen pc by mst.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Wed 17 Jul 2013 04:44:45 AM CDT using RSA key ID D28D5469
# gpg: Can't check signature: public key not found
# By Don Koch (2) and others
# Via Michael S. Tsirkin
* mst/tags/for_anthony:
pc: don't access fw cfg if NULL
virtio-net: add feature bit for any header s/g
net: add support of mac-programming over macvtap in QEMU side
pci: fix BRDIGE typo
pci-bridge: update mappings for migration/restore
Message-id: 1374054430-21966-1-git-send-email-mst@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Fix for LP#1187529: Devices on PCI bridge stop working when
live-migrated. Update bridge mappings for all PCI bridge
devices in get_pci_config_device().
Signed-off-by: Don Koch <dkoch@verizon.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This includes some pci enhancements:
Better support for systems with multiple PCI root buses
FW cfg interface for more robust pci programming in BIOS
Minor fixes/cleanups for fw cfg and cross-version migration -
because of dependencies with other patches
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQEcBAABAgAGBQJR2ctmAAoJECgfDbjSjVRpQpAH/Rk00yLrQ2R5ScNa8AL9LeaJ
gVFndBmmuRz4gdhyATx6lzR98ic32iTr0+YR5mL51btgmM5a0bEd/SIu34nXriWj
PsM0wdXfo/oEygdttxhvzJOH17tohRV9xg2WA2d8BEwDzrDyqoQ4J0VJlHlG7u3W
nq4KVDVUpLNQFKG8ZgJ2vW0WMw/mBSj2rluhQUALhcuvChphtvAFZ2rsSfJr6bzD
aBELrtIvfLvPGN/0WVeYs9qlp4EE03H3X6gN61QvV3/YElxubKUV5XyMDOX2dW3D
2j0NQi84LYHn0SFap2r/Kgm47/F6Q56SFk5lrgZrg60mhQTwocw7PfL8CGxjXRI=
=gxxc
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mst/tags/for_anthony' into staging
pci,misc enhancements
This includes some pci enhancements:
Better support for systems with multiple PCI root buses
FW cfg interface for more robust pci programming in BIOS
Minor fixes/cleanups for fw cfg and cross-version migration -
because of dependencies with other patches
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Sun 07 Jul 2013 03:11:18 PM CDT using RSA key ID D28D5469
# gpg: Can't check signature: public key not found
# By David Gibson (10) and others
# Via Michael S. Tsirkin
* mst/tags/for_anthony:
pci: Fold host_buses list into PCIHostState functionality
pci: Remove domain from PCIHostBus
pci: Simpler implementation of primary PCI bus
pci: Add root bus parameter to pci_nic_init()
pci: Add root bus argument to pci_get_bus_devfn()
pci: Replace pci_find_domain() with more general pci_root_bus_path()
pci: Use helper to find device's root bus in pci_find_domain()
pci: Abolish pci_find_root_bus()
pci: Move pci_read_devaddr to pci-hotplug-old.c
pci: Cleanup configuration for pci-hotplug.c
pvpanic: fix fwcfg for big endian hosts
pvpanic: initialization cleanup
MAINTAINERS: s/Marcelo/Paolo/
e1000: cleanup process_tx_desc
pc_piix: cleanup init compat handling
pc: pass PCI hole ranges to Guests
pci: store PCI hole ranges in guestinfo structure
range: add Range structure
Message-id: 1373228271-31223-1-git-send-email-mst@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The host_buses list is an odd structure - a list of pointers to PCI root
buses existing in parallel to the normal qdev tree structure. This patch
removes it, instead putting the link pointers into the PCIHostState
structure, which have a 1:1 relationship to PCIHostBus structures anyway.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There are now no users of the domain field of PCIHostBus, so remove it
from the structure, and as a parameter from the pci_host_bus_register()
function which sets it.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently pci_find_primary_bus() searches the list of root buses for one
with domain 0. But since host buses are always registered with domain 0,
this just amounts to finding the only PCI host bus. The only remaining
users of pci_find_primary_bus() are in pci-hotplug-old.c, which implements
the old style pci_add/pci_del commands.
Therefore, this patch redefines pci_find_primary_bus() to find the only
PCI root bus, returning an error if there are multiple roots. The callers
in pci-hotplug-old.c are updated correspondingly, to produce sensible
error messages.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
At present, pci_nic_init() and pci_nic_init_nofail() assume that they will
only create a NIC under the primary PCI root. As we add support for
multiple PCI roots, that may no longer be the case. This patch adds a root
bus parameter to pci_nic_init() (and updates callers accordingly) to allow
the machine init code using it to specify the right PCI root for NICs
created by old-style -net nic parameters. NICs created new-style, with
-device can of course be put anywhere.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
pci_get_bus_devfn() interprets a full PCI address string to give a PCIBus *
and device/function number within that bus. Currently it assumes it is
working on an address under the primary PCI root bus. This patch extends
it to allow the caller to specify a root bus. This might seem a little odd
since the supplied address can (theoretically) include a PCI domain number.
However, attempting to use a non-zero domain number there is currently an
error, so that shouldn't really cause problems.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
pci_find_domain() is used in a number of places where we want an id for a
whole PCI domain (i.e. the subtree under a PCI root bus). The trouble is
that many platforms may support multiple independent host bridges with no
hardware supplied notion of domain number.
This patch, therefore, replaces calls to pci_find_domain() with calls to
a new pci_root_bus_path() returning a string. The new call is implemented
in terms of a new callback in the host bridge class, so it can be defined
in some way that's well defined for the platform. When no callback is
available we fall back on the qbus name.
Most current uses of pci_find_domain() are for error or informational
messages, so the change in identifiers should be harmless. The exception
is pci_get_dev_path(), whose results form part of migration streams. To
maintain compatibility with old migration streams, the PIIX PCI host is
altered to always supply "0000" for this path, which matches the old domain
number (since the code didn't actually support domains other than 0).
For the pseries (spapr) PCI bridge we use a different platform-unique
identifier (pseries machines can routinely have dozens of PCI host
bridges). Theoretically that breaks migration streams, but given that we
don't yet have migration support for pseries, it doesn't matter.
Any other machines that have working migration support including PCI
devices will need to be updated to maintain migration stream compatibility.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently pci_find_domain() performs two functions - it locates the PCI
root bus above the given bus, then looks up that root bus's domain number.
This patch adds a helper function to perform the first task, finding the
root bus for a given PCI device. This is then used in pci_find_domain().
This changes pci_find_domain()'s signature slightly, taking a PCIDevice
instead of a PCIBus - since all callers passed something of the form
dev->bus, this simplifies things slightly.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
pci_find_root_bus() takes a domain parameter. Currently PCI root buses
with domain other than 0 can't be created, so this is more or less a long
winded way of retrieving the main PCI root bus. Numbered domains don't
actually properly cover the (non x86) possibilities for multiple PCI root
buses, so this patch for now enforces the domain == 0 restriction in other
places to replace pci_find_root_bus() with an explicit
pci_find_primary_bus().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
pci_read_devaddr() is only used by the legacy functions for the old PCI
hotplug interface in pci-hotplug-old.c. So we move the function there,
and make it static.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
pci-hotplug.c and the CONFIG_PCI_HOTPLUG variable which controls its
compilation are misnamed. They're not about PCI hotplug in general, but
rather about the pci_add/pci_del interface which are now deprecated in
favour of the more general device_add/device_del interface. This patch
therefore renames them to pci-hotplug-old.c and CONFIG_PCI_HOTPLUG_OLD.
CONFIG_PCI_HOTPLUG=y was listed twice in {i386,x86_64}-softmmu.make for no
particular reason, so we clean that up too. In addition it was included in
ppc64-softmmu.mak for which the old hotplug interface was never used and is
unsuitable, so we remove that too.
Most of pci-hotplug.c was additionaly protected by #ifdef TARGET_I386. The
small piece which wasn't is only called from the pci_add and pci_del hooks
in hmp-commands.hx, which themselves were protected by #ifdef TARGET_I386.
This patch therefore also removes the #ifdef from pci-hotplug-old.c,
and changes the ifdefs in hmp-commands.hx to use CONFIG_PCI_HOTPLUG_OLD.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The "info mtree" command in QEMU console prints only "memory" and "I/O"
address spaces while there are actually a lot more other AddressSpace
structs created by PCI and VIO devices. Those devices do not normally
have names and therefore not present in "info mtree" output.
The patch fixes this.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The DMAContext is a simple pointer to an AddressSpace that is now always
already available. Make everyone hold the address space directly,
and clean up the DMA API to use the AddressSpace directly.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use the new iommu support in the memory core for iommu support. The only
user, spapr, is also converted, but it still provides a DMAContext
interface until the non-PCI bits switch to AddressSpace.
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Avi Kivity <avi.kivity@gmail.com>
[ Do not calls memory_region_del_subregion() on the device's
bus_master_enable_region, it is an alias; return an AddressSpace
from the IOMMU hook and remove the destructor hook. - David Gibson ]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The translate function in the DMAContext is now always NULL.
Remove every reference to it.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Using a trick cut+pasted from vmstate_scsi_device
to wind up msix_save and msix_load.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Many of these should be cleaned up with proper qdev-/QOM-ification.
Right now there are many catch-all headers in include/hw/ARCH depending
on cpu.h, and this makes it necessary to compile these files per-target.
However, fixing this does not belong in these patches.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
usb-storage takes care to fetch the USB serial number from -drive
options, but it neglected to pass its own 'serial' property to the
scsi-disk it creates. With this patch, the 'serial' qdev property and
the 'serial' option in -drive behave the same and correctly apply the
serial number on both USB and SCSI level.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Work by Alex to support VGA assignment,
pci and virtio fixes by Stefan, Jason and myself, and a
new qmp event for hotplug support by myself.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQEcBAABAgAGBQJRUfDAAAoJECgfDbjSjVRp5wwH/RiNzEuC0SNuMArXh2LS+qjn
EavcSRTas5800Rl8bW2iYwJV38WhyW7jKs3JxbL5iK6XLeZvr7mureMRpsT6N5cR
WPqoZBw2jIxcHmYZODHTGd9SrAmF2LpfKypN3a86P5P4sQvV/dEusPQx7ZNyi5I5
kdhqNyP6Q6scAUbJVrNUbcOy8euLUtpEO2VQju/gikz2KLsQj6Hyxt9vKV2ZquYU
B7pKvYt5UZhNPqhfBmRptW+U0CMYUPiZBZkZsTEPUibIFHQqGkMD/KtthFFDZc/U
hjxttuETzjACR3KKgegwLVYCFEF8WadPJark4LWb4D9TA1MIdgo2NabNpqYxqrA=
=PY9F
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mst/tags/for_anthony' into staging
virtio,pci,qom
Work by Alex to support VGA assignment,
pci and virtio fixes by Stefan, Jason and myself, and a
new qmp event for hotplug support by myself.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 26 Mar 2013 02:02:24 PM CDT using RSA key ID D28D5469
# gpg: Can't check signature: public key not found
# By Alex Williamson (13) and others
# Via Michael S. Tsirkin
* mst/tags/for_anthony: (23 commits)
pcie: Add endpoint capability initialization wrapper
roms: switch oldnoconfig to olddefconfig
pcie: Mangle types to match topology
pci: Create and use API to determine root buses
pci: Create pci_bus_is_express helper
pci: Q35, Root Ports, and Switches create PCI Express buses
pci: Allow PCI bus creation interfaces to specify the type of bus
pci: Move PCI and PCIE type defines
pci: Create and register a new PCI Express TypeInfo
exec: assert that RAMBlock size is non-zero
pci: refuse empty ROM files
pci_bridge: Remove duplicate IRQ swizzle function
pci_bridge: Use a default map_irq function
pci: Fix INTx routing notifier recursion
pci_bridge: drop formatting from source
pci_bridge: factor out common code
pci: Teach PCI Bridges about VGA routing
pci: Add PCI VGA helpers
virtio-pci: guest notifier mask without non-irqfd
virtio-net: remove layout assumptions for mq ctrl
...
Fix the awkward API of mangling the caller specified PCIe type and
just provide an interface to initialize an endpoint device. This
will pick either a regular endpoint or integrated endpoint based on
the bus and return pcie_cap_init to doing exactly what is asked.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Windows will fail to start drivers for devices with an Endpoint type
PCIe capability attached to a Root Complex (code 10 - Device cannot
start). The proper type for such a device is Root Complex Integrated
Endpoint. Devices don't care which they are, so do this conversion
automatically.
This allows the Windows driver to load for nec-usb-xhci when attached
to pcie.0 of a q35 machine.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Move these so that we can reference them from a more common header
instead of including pci_bus.h everywhere.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This will allow us to differentiate Express and Legacy buses.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A zero size ROM file is invalid and should produce a warning.
Attempting to use a zero size file ends up hitting an assertion
qemu_ram_set_idstr() because RAMBlocks with duplicate addresses are
allocated - due to zero size the allocator doesn't increment the next
available RAMBlock offset.
Also convert __FUNCTION__ to __func__ while we're touching this code.
There are no other __FUNCTION__ instances in pci.c anymore.
Reported-by: Milos Ivanovic <milosivanovic@orcon.net.nz>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The PCI bridge spec defines a default swizzle for translating INTx
IRQs from secondary bus to primary. Use this by default for any
bridge that doesn't set a function.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For some reason we recurse to fire the INTx routing notifier for each
child of a bus, for each possible device of a bus. That means that if
we add a root port, the notifier gets called for that bridge 256
times. If we add an upstream switch behind that root port, 256^2. But
of course we need a downstream switch, 256^3. This starts to be
noticeable. Stop the insanity.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We use the same formatting for all files, it
doesn't make sense to have formatting directives only
in pci bridge header.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reuse common code in pcie_port, override the hardwired-to-0
bits per PCI Express spec.
No functional change but makes the code easier to follow.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Each PCI Bridge has a set of implied VGA regions that are enabled when
the VGA bit is set in the bridge control register. This allows VGA
devices behind bridges. Unfortunately with VGA Enable, which we
formerly allowed but didn't back, comes along some required VGA
baggage. VGA Palette Snooping is required, along with VGA 16-bit
decoding. We don't yet have support for palette snooping.
We also don't have support for 10-bit VGA aliases, the default mode, but
we enable the register, even on root ports, to avoid confusing guests.
Fortunately there's likely nothing from this century that requires these
features, so the missing bits are noted with TODOs.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Allow devices to register VGA memory regions for handling PCI spec
defined VGA I/O port and MMIO areas. PCI will attach these to the
bus address spaces and enable them according to the device command
register value.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fix various typos and misspellings. The bulk of these were found with
codespell.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
* bonzini/hw-dirs:
sh: move files referencing CPU to hw/sh4/
ppc: move more files to hw/ppc
ppc: move files referencing CPU to hw/ppc/
m68k: move files referencing CPU to hw/m68k/
i386: move files referencing CPU to hw/i386/
arm: move files referencing CPU to hw/arm/
hw: move boards and other isolated files to hw/ARCH
ppc: express FDT dependency of pSeries and e500 boards via default-configs/
build: always link device_tree.o into emulators if libfdt available
hw: include hw header files with full paths
ppc: do not use ../ in include files
vt82c686: vt82c686 is not a PCI host bridge
virtio-9p: remove PCI dependencies from hw/9pfs/
virtio-9p: use CONFIG_VIRTFS, not CONFIG_LINUX
hw: move device-hotplug.o to toplevel, compile it once
hw: move qdev-monitor.o to toplevel directory
hw: move fifo.[ch] to libqemuutil
hw: move char backends to backends/
Conflicts:
backends/baum.c
backends/msmouse.c
hw/a15mpcore.c
hw/arm/Makefile.objs
hw/arm/pic_cpu.c
hw/dataplane/event-poll.c
hw/dataplane/virtio-blk.c
include/char/baum.h
include/char/msmouse.h
qemu-char.c
vl.c
Resolve conflicts caused by header movements.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The address_space field of PCIHostState was only ever written, never used.
Drop it completely.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
qdev-monitor.c is the only "core qdev" file that is not used in
user-mode emulation, and it does not define anything that is used
by hardware models. Remove it from the hw/ directory and
remove hw/qdev-monitor.h from hw/qdev.h too; this requires
some files to have some new explicitly includes.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove knowledge of QOM innards. The common part of pci_bus_new and
pci_bus_new_inplace is moved to a new function pci_bus_init.
Acked-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
extra-obj-y is somewhat complicated to understand. Replace it with a
special CONFIG_ALL symbol that is defined only at toplevel.
This limits the case of directories defining more than one
*-obj-y target.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The TPCI200 is a PCI board that supports up to 4 IndustryPack modules.
A new bus type called 'IndustryPack' has been created so any
compatible module can be attached to this board.
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Alberto Garcia <agarcia@igalia.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This further optimizes MSIX handling in virtio-pci.
Also included is pci cleanup by Paolo, and pci device
assignment fix by Alex.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQ7ZaiAAoJECgfDbjSjVRpFhcIAJkY4VQ3i7TLnLsnEDOR+FrP
66YLEDwCSiKZ/UW7WERGN3p3tm0hAXLhPoHFqMGRPPV9pdcXI+Eb8v+u0IHVlt+7
DsQ9TIemZkpSMuUJjQbu/RF8k9JV8+X7M6CKnWahq68p0UD/vDX+OgCiGKO/l/zY
tENJhwD6M1MMzbxyzd4nCnkf3CPrHFvpPt2VAqQnkCw3wLAtR34SucBjr/dXcjuT
arPiV8dNmXHTosdKvcodAWA+0YLLE7Bhz0nLK6eTt5L/UsfdbRN8q9Xdhd5nJjji
DjKBJBfwdG5n3r96g7dlb/XdHuQjbFBq3uLmc8H2OdWOrk5PyqeoUA5fdBQxkb8=
=vKSI
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mst/tags/for_anthony' into staging
pci,virtio
This further optimizes MSIX handling in virtio-pci.
Also included is pci cleanup by Paolo, and pci device
assignment fix by Alex.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
* mst/tags/for_anthony:
pci-assign: Enable MSIX on device to match guest
pci: use constants for devices under the 1B36 device ID, document them
ivshmem: use symbolic constant for PCI ID, add to pci-ids.txt
virtio-9p: use symbolic constant, add to pci-ids.txt
reorganize pci-ids.txt
docs: move pci-ids.txt to docs/specs/
vhost: backend masking support
vhost: set started flag while start is in progress
virtio-net: set/clear vhost_started in reverse order
virtio: backend virtqueue notifier masking
virtio-pci: cache msix messages
kvm: add stub for update msi route
msix: add api to access msix message
virtio: don't waste irqfds on control vqs
Since 39bffca203 (qdev: register all
types natively through QEMU Object Model), TypeInfo as used in
the common, non-iterative pattern is no longer amended with information
and should therefore be const.
Fix the documented QOM examples:
sed -i 's/static TypeInfo/static const TypeInfo/g' include/qom/object.h
Since frequently the wrong examples are being copied by contributors of
new devices, fix all types in the tree:
sed -i 's/^static TypeInfo/static const TypeInfo/g' */*.c
sed -i 's/^static TypeInfo/static const TypeInfo/g' */*/*.c
This also avoids to piggy-back these changes onto real functional
changes or other refactorings.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Upper 16 bits of the PCIe Extended Capability Header was truncated during update,
also breaking pcie_add_capability.
Signed-off-by: Knut Omang <knut.omang@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Move public headers to include/net, and leave private headers in net/.
Put the virtio headers in include/net/tap.h, removing the multiple copies
that existed. Leave include/net/tap.h as the interface for NICs, and
net/tap_int.h as the interface for OS-specific parts of the tap backend.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There are lots of external users of pci_internals.h,
apparently making it an internal interface only didn't
work out. Let's stop pretending it's an internal header.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This reverts commit 475d67c3bcd6ba9fef917b6e59d96ae69eb1a9b4.
Now that all users have been updated, we don't need the
makefile hack or the softlink anymore.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Include dependencies from pci core using the correct path.
This is required now that it's in the separate directory.
Need to check whether they can be minimized, for now,
keep the code as is.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To make it easier to move code around without breaking
build at intermedite steps, tweak makefiles
to look in pci/ and hw/ for include files, automatically.
This will be reverted at the end of the reorganization.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
