The MacOS toolbox ROM accesses a number of addresses between 0x0 and 0x200 during
initialisation and resolution changes. Whilst the function of many of these
registers is unknown, it is worth the minimal cost of saving these extra values as
part of migration to help future-proof the migration stream for the q800 machine
as it starts to stabilise.
Note this is a migration break, but since there are upcoming incompatible changes
for the q800 machine (and migration does not even succeed without these patches)
then this is not an issue.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220305155530.9265-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The current IRQ state and IRQ mask are handled exactly the same as standard
register accesses, so store these values directly in the regs array rather
than having separate variables for them.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220305155530.9265-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Now that the logic related to edge-triggered interrupts is all contained within
the mos6522 device the redundant implementation for the mac99 PMU device can
be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220305150957.5053-13-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The mos6522 datasheet describes how the control lines IRQs are edge-triggered
according to the configuration in the PCR register. Implement the logic according
to the datasheet so that the interrupt bits in IFR are latched when the edge is
detected, and cleared when reading portA/portB or writing to IFR as necessary.
To maintain bisectibility this change also updates the SCSI, SCSI data, Nubus
and VIA2 60Hz/1Hz clocks in the q800 machine to be negative edge-triggered as
confirmed by the PCR programming in all of Linux, NetBSD and MacOS.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220305150957.5053-12-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
To detect edge-triggered IRQs it is necessary to store the last state of each
IRQ in a last_irq_levels bitmap.
Note: this is a migration break for machines which use mos6522 instances which
are g3beige/mac99 (PPC) and q800 (m68k).
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220305150957.5053-10-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This displays detailed information about the device registers and timers to aid
debugging problems with timers and interrupts.
Currently the QAPI generators for HumanReadableText don't work correctly if
used in qapi/target-misc.json when a non-specified target is built, so for
now manually add a hmp_info_via() wrapper until direct support for per-device
HMP/QMP commands is implemented.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220305150957.5053-9-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This helps to follow how the guest is programming the mos6522 when debugging.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220305150957.5053-8-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Now that the mos6522 IRQs are managed using standard qdev gpios these methods
are no longer required.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220305150957.5053-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
For historical reasons each mos6522 instance implements its own setting and
update of the IFR flag bits using methods exposed by MOS6522DeviceClass. As
of today this is no longer required, and it is now possible to implement
the mos6522 IRQs as standard qdev gpios.
Switch over to use qdev gpios for the mos6522 device and update all instances
accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220305150957.5053-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This allows us to easily see how the physical control lines are mapped to the
IFR bit flags.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220305150957.5053-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This allows us to easily see how the physical control lines are mapped to the
IFR bit flags.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220305150957.5053-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
These are intended to make it easier to see how the physical control lines
are wired for each instance.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220305150957.5053-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
vhost-user enabled on non-linux systems
beginning of nvme sriov support
bigger tx queue for vdpa
virtio iommu bypass
FADT flag to detect legacy keyboards
Fixes, cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmImipMPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpD5AH/jz73VVDE3dZTtsdEH/f2tuO8uosur9fIjHJ
nCMwBoosdDWmrWjrwxynmG6e+qIcOHEGdTInvS1TY2OTU+elNNTiR57pWiljXRsJ
2kNIXKp4dXaYI/bxmKUzKSoVscyWxL686ND4U8sZhuppSNrWpLmMUNgwqmYjQQLV
yd2JpIKgZYnzShPnJMDtF3ItcCHetY6jeB28WAclKywIEuCTmjulYCTaH5ujroG9
rykMaQIjoe/isdmCcBx05UuMxH61vf5L8pR06N6e3GO9T2/Y/hWuteVoEJaCQvNa
+zIyL2hOjGuMKr+icLo9c42s3yfwWNsRfz87wqdAY47yYSyc1wo=
=3NVe
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio,pc,pci: features, cleanups, fixes
vhost-user enabled on non-linux systems
beginning of nvme sriov support
bigger tx queue for vdpa
virtio iommu bypass
FADT flag to detect legacy keyboards
Fixes, cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Mon 07 Mar 2022 22:43:31 GMT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (47 commits)
hw/acpi/microvm: turn on 8042 bit in FADT boot architecture flags if present
tests/acpi: i386: update FACP table differences
hw/acpi: add indication for i8042 in IA-PC boot flags of the FADT table
tests/acpi: i386: allow FACP acpi table changes
docs: vhost-user: add subsection for non-Linux platforms
configure, meson: allow enabling vhost-user on all POSIX systems
vhost: use wfd on functions setting vring call fd
event_notifier: add event_notifier_get_wfd()
pci: drop COMPAT_PROP_PCP for 2.0 machine types
hw/smbios: Add table 4 parameter, "processor-id"
x86: cleanup unused compat_apic_id_mode
vhost-vsock: detach the virqueue element in case of error
pc: add option to disable PS/2 mouse/keyboard
acpi: pcihp: pcie: set power on cap on parent slot
pci: expose TYPE_XIO3130_DOWNSTREAM name
pci: show id info when pci BDF conflict
hw/misc/pvpanic: Use standard headers instead
headers: Add pvpanic.h
pci-bridge/xio3130_downstream: Fix error handling
pci-bridge/xio3130_upstream: Fix error handling
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# docs/specs/index.rst
* cleanups of qemu_oom_check() and qemu_memalign()
* target/arm/translate-neon: UNDEF if VLD1/VST1 stride bits are non-zero
* target/arm/translate-neon: Simplify align field check for VLD3
* GICv3 ITS: add more trace events
* GICv3 ITS: implement 8-byte accesses properly
* GICv3: fix minor issues with some trace/log messages
* ui/cocoa: Use the standard about panel
* target/arm: Provide cpu property for controling FEAT_LPA2
* hw/arm/virt: Disable LPA2 for -machine virt-6.2
-----BEGIN PGP SIGNATURE-----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=ix0J
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20220307' into staging
target-arm queue:
* cleanups of qemu_oom_check() and qemu_memalign()
* target/arm/translate-neon: UNDEF if VLD1/VST1 stride bits are non-zero
* target/arm/translate-neon: Simplify align field check for VLD3
* GICv3 ITS: add more trace events
* GICv3 ITS: implement 8-byte accesses properly
* GICv3: fix minor issues with some trace/log messages
* ui/cocoa: Use the standard about panel
* target/arm: Provide cpu property for controling FEAT_LPA2
* hw/arm/virt: Disable LPA2 for -machine virt-6.2
# gpg: Signature made Mon 07 Mar 2022 16:46:06 GMT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20220307:
hw/arm/virt: Disable LPA2 for -machine virt-6.2
target/arm: Provide cpu property for controling FEAT_LPA2
ui/cocoa: Use the standard about panel
hw/intc/arm_gicv3_cpuif: Fix register names in ICV_HPPIR read trace event
hw/intc/arm_gicv3: Fix missing spaces in error log messages
hw/intc/arm_gicv3: Specify valid and impl in MemoryRegionOps
hw/intc/arm_gicv3_its: Add trace events for table reads and writes
hw/intc/arm_gicv3_its: Add trace events for commands
target/arm/translate-neon: Simplify align field check for VLD3
target/arm/translate-neon: UNDEF if VLD1/VST1 stride bits are non-zero
osdep: Move memalign-related functions to their own header
util: Put qemu_vfree() in memalign.c
util: Use meson checks for valloc() and memalign() presence
util: Share qemu_try_memalign() implementation between POSIX and Windows
meson.build: Don't misdetect posix_memalign() on Windows
util: Return valid allocation for qemu_try_memalign() with zero size
util: Unify implementations of qemu_memalign()
util: Make qemu_oom_check() a static function
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There is a Linux kernel bug present until v5.12 that prevents
booting with FEAT_LPA2 enabled. As a workaround for TCG,
disable this feature for machine versions prior to 7.0.
Cc: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
ArchCPU is our interface with target-specific code. Use it as
a forward-declared opaque pointer (abstract type), having its
structure defined by each target.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220214183144.27402-15-f4bug@amsat.org>
Replace the boilerplate code to declare CPU QOM types
and macros, and forward-declare the CPU instance type.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220214183144.27402-14-f4bug@amsat.org>
While CPUState is our interface with generic code, CPUArchState is
our interface with target-specific code. Use CPUArchState as an
abstract type, defined by each target.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220214183144.27402-13-f4bug@amsat.org>
This can allow the guest OS to determine more easily if i8042 controller
is present in the system or not, so it doesn't need to do probing of the
controller, but just initialize it immediately, before enumerating the
ACPI AML namespace.
The 8042 bit in IAPC_BOOT_ARCH was introduced from ACPI spec v2 (FADT
revision 2 and above). Therefore, in this change, we only enable this bit for
x86/q35 machine types since x86/i440fx machines use FADT ACPI table with
revision 1.
Signed-off-by: Liav Albani <liavalb@gmail.com>
Signed-off-by: Ani Sinha <ani@anisinha.ca>
Message-Id: <20220304154032.2071585-3-ani@anisinha.ca>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Move vaddr type declaration to the generic "exec/cpu-common.h" header.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220207075426.81934-4-f4bug@amsat.org>
commit
f862ddbb1a (hw/i386: Remove the deprecated pc-1.x machine types)
removed the last user of broken APIC ID compat knob,
but compat_apic_id_mode itself was forgotten.
Clean it up and simplify x86_cpu_apic_id_from_index()
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20220228131634.3389805-1-imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
On some older software like Windows 7 installer, having both a PS/2
mouse and USB mouse results in only one device working property (which
might be a different device each boot). While the workaround to not use
a USB mouse with such software is valid, it creates an inconsistent
experience if the user wishes to always use a USB mouse.
This introduces a new machine property to inhibit the creation of the
i8042 PS/2 controller.
Signed-off-by: Joelle van Dyne <j@getutm.app>
Message-Id: <20220227210655.45592-1-j@getutm.app>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
on creation a PCIDevice has power turned on at the end of pci_qdev_realize()
however later on if PCIe slot isn't populated with any children
it's power is turned off. It's fine if native hotplug is used
as plug callback will power slot on among other things.
However when ACPI hotplug is enabled it replaces native PCIe plug
callbacks with ACPI specific ones (acpi_pcihp_device_*plug_cb) and
as result slot stays powered off. It works fine as ACPI hotplug
on guest side takes care of enumerating/initializing hotplugged
device. But when later guest is migrated, call chain introduced by]
commit d5daff7d31 (pcie: implement slot power control for pcie root ports)
pcie_cap_slot_post_load()
-> pcie_cap_update_power()
-> pcie_set_power_device()
-> pci_set_power()
-> pci_update_mappings()
will disable earlier initialized BARs for the hotplugged device
in powered off slot due to commit 23786d1344 (pci: implement power state)
which disables BARs if power is off.
Fix it by setting PCI_EXP_SLTCTL_PCC to PCI_EXP_SLTCTL_PWR_ON
on slot (root port/downstream port) at the time a device
hotplugged into it. As result PCI_EXP_SLTCTL_PWR_ON is migrated
to target and above call chain keeps device plugged into it
powered on.
Fixes: d5daff7d31 ("pcie: implement slot power control for pcie root ports")
Fixes: 23786d1344 ("pci: implement power state")
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=2053584
Suggested-by: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20220301151200.3507298-3-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Type name will be used in followup patch for cast check
in pcihp code.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20220301151200.3507298-2-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
QEMU side has already imported pvpanic.h from linux, remove bit
definitions from include/hw/misc/pvpanic.h, and use
include/standard-headers/linux/pvpanic.h instead.
Also minor changes for PVPANIC_CRASHLOADED -> PVPANIC_CRASH_LOADED.
Signed-off-by: zhenwei pi <pizhenwei@bytedance.com>
Message-Id: <20220221122717.1371010-2-pizhenwei@bytedance.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Łukasz Gieryk <lukasz.gieryk@linux.intel.com>
Message-Id: <20220217174504.1051716-5-lukasz.maniak@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Convenience function for retrieving the PCIDevice object of the N-th VF.
Signed-off-by: Łukasz Gieryk <lukasz.gieryk@linux.intel.com>
Reviewed-by: Knut Omang <knuto@ifi.uio.no>
Message-Id: <20220217174504.1051716-4-lukasz.maniak@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch provides the building blocks for creating an SR/IOV
PCIe Extended Capability header and register/unregister
SR/IOV Virtual Functions.
Signed-off-by: Knut Omang <knuto@ifi.uio.no>
Message-Id: <20220217174504.1051716-2-lukasz.maniak@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently the virtio-iommu device must be programmed before it allows
DMA from any PCI device. This can make the VM entirely unusable when a
virtio-iommu driver isn't present, for example in a bootloader that
loads the OS from storage.
Similarly to the other vIOMMU implementations, default to DMA bypassing
the IOMMU during boot. Add a "boot-bypass" property, defaulting to true,
that lets users change this behavior.
Replace the VIRTIO_IOMMU_F_BYPASS feature, which didn't support bypass
before feature negotiation, with VIRTIO_IOMMU_F_BYPASS_CONFIG.
We add the bypass field to the migration stream without introducing
subsections, based on the assumption that this virtio-iommu device isn't
being used in production enough to require cross-version migration at
the moment (all previous version required workarounds since they didn't
support ACPI and boot-bypass).
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-Id: <20220214124356.872985-3-jean-philippe@linaro.org>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
SC is required for some kernel features like vhost-vDPA. So this patch
implements basic SC feature. The idea is pretty simple, for software
emulated DMA it would be always coherent. In this case we can simple
advertise ECAP_SC bit. For VFIO and vhost, thing will be more much
complicated, so this patch simply fail the IOMMU notifier
registration.
In the future, we may want to have a dedicated notifiers flag or
similar mechanism to demonstrate the coherency so VFIO could advertise
that if it has VFIO_DMA_CC_IOMMU, for vhost kernel backend we don't
need that since it's a software backend.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20220214060346.72455-1-jasowang@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
VIRTIO_I2C_F_ZERO_LENGTH_REQUEST is a mandatory feature, that must be
implemented by everyone. Add its support.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Message-Id: <fc47ab63b1cd414319c9201e8d6c7705b5ec3bd9.1644490993.git.viresh.kumar@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When vhost-user device cleanup, remove notifier MR and munmaps notifier
address in the event-handling thread, VM CPU thread writing the notifier
in concurrent fails with an error of accessing invalid address. It
happens because MR is still being referenced and accessed in another
thread while the underlying notifier mmap address is being freed and
becomes invalid.
This patch calls RCU and munmap notifiers in the callback after the
memory flatview update finish.
Fixes: 44866521bd ("vhost-user: support registering external host notifiers")
Cc: qemu-stable@nongnu.org
Signed-off-by: Xueming Li <xuemingl@nvidia.com>
Message-Id: <20220207071929.527149-3-xuemingl@nvidia.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Notifier set when vhost-user backend asks qemu to mmap an FD and
offset. When vhost-user backend restart or getting killed, VQ notifier
FD and mmap addresses become invalid. After backend restart, MR contains
the invalid address will be restored and fail on notifier access.
On the other hand, qemu should munmap the notifier, release underlying
hardware resources to enable backend restart and allocate hardware
notifier resources correctly.
Qemu shouldn't reference and use resources of disconnected backend.
This patch removes VQ notifier restore, uses the default vhost-user
notifier to avoid invalid address access.
After backend restart, the backend should ask qemu to install a hardware
notifier if needed.
Fixes: 44866521bd ("vhost-user: support registering external host notifiers")
Cc: qemu-stable@nongnu.org
Signed-off-by: Xueming Li <xuemingl@nvidia.com>
Message-Id: <20220207071929.527149-2-xuemingl@nvidia.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* Fixup checks for ext_zb[abcs]
* Add AIA support for virt machine
* Increase maximum number of CPUs in virt machine
* Fixup OpenTitan SPI address
* Add support for zfinx, zdinx and zhinx{min} extensions
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAmIgUZ8ACgkQIeENKd+X
cFTzegf8DbUYFLpyfURm6bJoJfLQHjtjB4Hs6PnszJZZAEtC6Ia+551TDjh93vTf
GTbpWm0BlugQqEeyg+Mioe2mb2EhK2w208RGXRSDjT9QFVOaIp83NDAjaQTPqs22
XC35ygJYuo1Yf0WoJV77aB6IYPZB3ba5i+dkGb6lk60Ru5ULqoLvqp73tNe5KvNB
uVAEy+ubzjmzWs5hGPw95HqTIbcMGnlHew4XU6xJaiJixSy71Z5nOCCn+2sxk+6A
QW59Onglyfk01F9ac3GMLvi2e+FUdj0S0y07oVqchzxXWYpYwgTO4Xkt794c8mqU
T02kuelfubr1qH1z/IolStju1JnaXw==
=LzOY
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/alistair/tags/pull-riscv-to-apply-20220303' into staging
Fifth RISC-V PR for QEMU 7.0
* Fixup checks for ext_zb[abcs]
* Add AIA support for virt machine
* Increase maximum number of CPUs in virt machine
* Fixup OpenTitan SPI address
* Add support for zfinx, zdinx and zhinx{min} extensions
# gpg: Signature made Thu 03 Mar 2022 05:26:55 GMT
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [full]
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-to-apply-20220303:
target/riscv: expose zfinx, zdinx, zhinx{min} properties
target/riscv: add support for zhinx/zhinxmin
target/riscv: add support for zdinx
target/riscv: add support for zfinx
target/riscv: hardwire mstatus.FS to zero when enable zfinx
target/riscv: add cfg properties for zfinx, zdinx and zhinx{min}
hw: riscv: opentitan: fixup SPI addresses
hw/riscv: virt: Increase maximum number of allowed CPUs
docs/system: riscv: Document AIA options for virt machine
hw/riscv: virt: Add optional AIA IMSIC support to virt machine
hw/intc: Add RISC-V AIA IMSIC device emulation
hw/riscv: virt: Add optional AIA APLIC support to virt machine
target/riscv: fix inverted checks for ext_zb[abcs]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch updates the SPI_DEVICE, SPI_HOST0, SPI_HOST1
base addresses. Also adds these as unimplemented devices.
The address references can be found [1].
[1] 6c317992fb/hw/top_earlgrey/sw/autogen/top_earlgrey_memory.h (L107)
Signed-off-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20220218063839.405082-1-alistair.francis@opensource.wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
To facilitate software development of RISC-V systems with large number
of HARTs, we increase the maximum number of allowed CPUs to 512 (2^9).
We also add a detailed source level comments about limit defines which
impact the physical address space utilization.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Message-Id: <20220220085526.808674-6-anup@brainfault.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We extend virt machine to emulate both AIA IMSIC and AIA APLIC
devices only when "aia=aplic-imsic" parameter is passed along
with machine name in the QEMU command-line. The AIA IMSIC is
only a per-HART MSI controller so we use AIA APLIC in MSI-mode
to forward all wired interrupts as MSIs to the AIA IMSIC.
We also provide "aia-guests=<xyz>" parameter which can be used
to specify number of VS-level AIA IMSIC Guests MMIO pages for
each HART.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220220085526.808674-4-anup@brainfault.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The RISC-V AIA (Advanced Interrupt Architecture) defines a new
interrupt controller for MSIs (message signal interrupts) called
IMSIC (Incoming Message Signal Interrupt Controller). The IMSIC
is per-HART device and also suppport virtualizaiton of MSIs using
dedicated VS-level guest interrupt files.
This patch adds device emulation for RISC-V AIA IMSIC which
supports M-level, S-level, and VS-level MSIs.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Message-Id: <20220220085526.808674-3-anup@brainfault.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We extend virt machine to emulate AIA APLIC devices only when
"aia=aplic" parameter is passed along with machine name in QEMU
command-line. When "aia=none" or not specified then we fallback
to original PLIC device emulation.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220220085526.808674-2-anup@brainfault.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Add new macros to manipulate signed fields within the register.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220301215958.157011-2-richard.henderson@linaro.org
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* ppc/pnv fixes
* PMU EBB support
* target/ppc: PowerISA Vector/VSX instruction batch
* ppc/pnv: Extension of the powernv10 machine with XIVE2 ans PHB5 models
* spapr allocation cleanups
-----BEGIN PGP SIGNATURE-----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=kWv5
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/legoater/tags/pull-ppc-20220302' into staging
ppc-7.0 queue
* ppc/pnv fixes
* PMU EBB support
* target/ppc: PowerISA Vector/VSX instruction batch
* ppc/pnv: Extension of the powernv10 machine with XIVE2 ans PHB5 models
* spapr allocation cleanups
# gpg: Signature made Wed 02 Mar 2022 11:00:42 GMT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* remotes/legoater/tags/pull-ppc-20220302: (87 commits)
hw/ppc/spapr_vio.c: use g_autofree in spapr_dt_vdevice()
hw/ppc/spapr_rtas.c: use g_autofree in rtas_ibm_get_system_parameter()
spapr_pci_nvlink2.c: use g_autofree in spapr_phb_nvgpu_ram_populate_dt()
hw/ppc/spapr_numa.c: simplify spapr_numa_write_assoc_lookup_arrays()
hw/ppc/spapr_drc.c: use g_autofree in spapr_drc_by_index()
hw/ppc/spapr_drc.c: use g_autofree in spapr_dr_connector_new()
hw/ppc/spapr_drc.c: use g_autofree in drc_unrealize()
hw/ppc/spapr_drc.c: use g_autofree in drc_realize()
hw/ppc/spapr_drc.c: use g_auto in spapr_dt_drc()
hw/ppc/spapr_caps.c: use g_autofree in spapr_caps_add_properties()
hw/ppc/spapr_caps.c: use g_autofree in spapr_cap_get_string()
hw/ppc/spapr_caps.c: use g_autofree in spapr_cap_set_string()
hw/ppc/spapr.c: fail early if no firmware found in machine_init()
hw/ppc/spapr.c: use g_autofree in spapr_dt_chosen()
pnv/xive2: Add support for 8bits thread id
pnv/xive2: Add support for automatic save&restore
xive2: Add a get_config() handler for the router configuration
pnv/xive2: Add support XIVE2 P9-compat mode (or Gen1)
ppc/pnv: add XIVE Gen2 TIMA support
pnv/xive2: Introduce new capability bits
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- restore TESTS/IMAGES filtering to docker tests
- add NOUSER to alpine image
- bump lcitool version
- move arm64/s390x cross build images to lcitool
- add aarch32 runner CI scripts
- expand testing to more vectors
- update s390x jobs to focal for gitlab/travis
- disable threadcount for all sh4
- fix semihosting SYS_HEAPINFO and test
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZoWumedRZ7yvyN81+9DbCVqeKkQFAmIdGJEACgkQ+9DbCVqe
KkQZYQf+Ndlm651dulO4J55puk8cUOMrCrDvqVkxM/V7ZD4GKyoa9/PstfOspLkQ
hXNANtfcr7zsXxo7J7PKVpX3y+upxCMLLK9NqHXW3O8mOSoru44caLko6FdmwWkU
KmoToEM3jgxJxqrE8ijLz1gxo79TVT0m3OyyKlMf9C+Wf4BfUe4NXjt/VMcecrDd
wKJnvjWyrk67yOyPRDnT2XlG1HdphD90g8xPxiK1tzkEQEWJlojTLSZENQksa1V6
JBu1mwT/KPodkllzTQcHHjGn4/vsdzFqjqV+8d3xXiSmr/QdeyByUeDhJ7aI4qdY
aKoX3hoIUdENmPxqXozuVBy/S4gLoA==
=MY0T
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stsquad/tags/pull-testing-and-semihosting-280222-1' into staging
Testing and semihosting updates:
- restore TESTS/IMAGES filtering to docker tests
- add NOUSER to alpine image
- bump lcitool version
- move arm64/s390x cross build images to lcitool
- add aarch32 runner CI scripts
- expand testing to more vectors
- update s390x jobs to focal for gitlab/travis
- disable threadcount for all sh4
- fix semihosting SYS_HEAPINFO and test
# gpg: Signature made Mon 28 Feb 2022 18:46:41 GMT
# gpg: using RSA key 6685AE99E75167BCAFC8DF35FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>" [full]
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* remotes/stsquad/tags/pull-testing-and-semihosting-280222-1:
tests/tcg: port SYS_HEAPINFO to a system test
semihosting/arm-compat: replace heuristic for softmmu SYS_HEAPINFO
tests/tcg: completely disable threadcount for sh4
gitlab: upgrade the job definition for s390x to 20.04
travis.yml: Update the s390x jobs to Ubuntu Focal
tests/tcg: add vectorised sha512 versions
tests/tcg: add sha512 test
tests/tcg: build sha1-vector with O3 and compare
tests/tcg/ppc64: clean-up handling of byte-reverse
gitlab: add a new aarch32 custom runner definition
scripts/ci: allow for a secondary runner
scripts/ci: add build env rules for aarch32 on aarch64
tests/docker: introduce debian-riscv64-test-cross
tests/docker: update debian-s390x-cross with lcitool
tests/docker: update debian-arm64-cross with lcitool
tests/lcitool: update to latest version
tests/docker: add NOUSER for alpine image
tests/docker: restore TESTS/IMAGES filtering
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The XIVE interrupt controller on P10 can automatically save and
restore the state of the interrupt registers under the internal NVP
structure representing the VCPU. This saves a costly store/load in
guest entries and exits.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add GEN1 config even if we don't use it yet in the core framework.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Only the CAM line updates done by the hypervisor are specific to
POWER10. Instead of duplicating the TM ops table, we handle these
commands locally under the PowerNV XIVE2 model.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
When the Address-Based Interrupt Trigger mode is activated, the PHB
maps the interrupt source number into the interrupt command address.
The PHB directly triggers the IC ESB page of the interrupt number and
not the notify page of the IC anymore.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The PQ_disable configuration bit disables the check done on the PQ
state bits when processing new MSI interrupts. When bit 9 is enabled,
the PHB forwards any MSI trigger to the XIVE interrupt controller
without checking the PQ state bits. The XIVE IC knows from the trigger
message that the PQ bits have not been checked and performs the check
locally.
This configuration bit only applies to MSIs and LSIs are still checked
on the PHB to handle the assertion level.
PQ_disable enablement is a requirement for StoreEOI.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The trigger message coming from a HW source contains a special bit
informing the XIVE interrupt controller that the PQ bits have been
checked at the source or not. Depending on the value, the IC can
perform the check and the state transition locally using its own PQ
state bits.
The following changes add new accessors to the XiveRouter required to
query and update the PQ state bits. This only applies to the PowerNV
machine. sPAPR accessors are provided but the pSeries machine should
not be concerned by such complex configuration for the moment.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is an internal offset used to inject triggers when the PQ state
bits are not controlled locally. Such as for LSIs when the PHB5 are
using the Address-Based Interrupt Trigger mode and on the END.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
