This adds IRQ controller in FPGA on r2d, and use it for CF.
Signed-off-by: Takashi YOSHII <takasi-y@ops.dti.ne.jp>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5926 c046a42c-6fe2-441c-8c8c-71466251a162
This patch adds IRL(4bit encoded 15 level interrupt input) support
to SH using qemu_irq as a multi level (!=on/off) signal.
Signed-off-by: Takashi YOSHII <takasi-y@ops.dti.ne.jp>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5925 c046a42c-6fe2-441c-8c8c-71466251a162
This patch adds emulation for a CompactFlash on sh4/r2d board.
The device is CF, but wired to be worked as True-IDE mode, and connected
directly to SH bus. So, this code is to support generally mmio based
IDEs which are supported by "pata_platform" driver in linux kernel.
Signed-off-by: Takashi YOSHII <takasi-y@ops.dti.ne.jp>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5924 c046a42c-6fe2-441c-8c8c-71466251a162
Openserver 5.0.5 sends an Inquiry command to the emulated SCSI disk
expecting a response length of 40 bytes. Currently the response to an
Inquiry command is hardcoded to 36 bytes. When receiving a response of
length 36 instead of 40 Openserver panics.
Modifications to original patch based on feedback from Ryan Harper and Paul
Brook. Thanks guys.
Signed-off-by: Justin Chevrier <address@hidden>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5903 c046a42c-6fe2-441c-8c8c-71466251a162
Basically after each DMA transfer the Openserver driver would issue an
empty (0) SCRIPTS opcode. As the opcode is essentially a NOP it has no
second DWORD and therefore the DSP should only be incremented by 4 bytes
instead of the 8 bytes we currently do.
Here's a snippet of the log:
lsi_scsi: Data ready tag=0x100d9 len=16384
...
lsi_scsi: SCRIPTS dsp=068c5e50 opcode 01000400 arg 07a09000
lsi_scsi: DMA addr=0x07a09000 len=1024
lsi_scsi: SCRIPTS dsp=068c5e58 opcode 00000000 arg 01000400
lsi_scsi: Wrong phase got 1 expected 0
Note the 2nd DWORD after the empty opcode; the next opcode in the DMA
transfer sequence. As can be expected the address after that has the next
DMA address to use.
After the attached patch the DMA transfer is able to complete successfully:
lsi_scsi: SCRIPTS dsp=068c5e50 opcode 01000400 arg 07a0d000
lsi_scsi: DMA addr=0x07a0d000 len=1024
lsi_scsi: SCRIPTS dsp=068c5e5c opcode 01000400 arg 07a0d400
lsi_scsi: DMA addr=0x07a0d400 len=1024
...
Tested againsted Openserver 5.0.5 and Debian ARM.
Signed-off-by: Justin Chevrier <address@hidden>
Acked-by: Ryan Harper <ryanh@us.ibm.com>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5902 c046a42c-6fe2-441c-8c8c-71466251a162
This way the registers will only be visible at the given offset instead of
every 0x100 bytes.
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5899 c046a42c-6fe2-441c-8c8c-71466251a162
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5898 c046a42c-6fe2-441c-8c8c-71466251a162
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5897 c046a42c-6fe2-441c-8c8c-71466251a162
Vectored IO APIs will require some sort of vector argument. It makes sense to
use struct iovec and just define it globally for Windows.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5889 c046a42c-6fe2-441c-8c8c-71466251a162
For backward operations, dstpitch and srcpitch can
be negative. This leads BLTUNSAFE macro into an
overflow, and as a result, it avoids performing
operations that are perfectly valid.
The visible effect that led to that patch was the gnome-panel
bar in Fedora10. Before this patch, you could see garbage
clobbering a big portion of the bar.
After this patch, this garbage is gone.
Signed-off-by: Glauber Costa <glommer@redhat.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5880 c046a42c-6fe2-441c-8c8c-71466251a162
qemu_get_clock() returns a structure containing the time the user wants
to be set (either UTC time, a local time, or a given date). Use mktimegm()
instead of mktime() to convert it into POSIX time without taking the host
timezone into account.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5878 c046a42c-6fe2-441c-8c8c-71466251a162
Windows does not have sys/uio.h and does not have err.h.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5877 c046a42c-6fe2-441c-8c8c-71466251a162
...and fix a bug, the implementation in hw/apic.c was wrong.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5876 c046a42c-6fe2-441c-8c8c-71466251a162
This adds a VirtIO based balloon driver. It uses madvise() to actually balloon
the memory when possible.
Until 2.6.27, KVM forced memory pinning so we must disable ballooning unless the
kernel actually supports it when using KVM. It's always safe when using TCG.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5874 c046a42c-6fe2-441c-8c8c-71466251a162
TARGET_PAGE_SIZE should only be used internal to qemu, not in guest/host
interfaces. The virtio frontend code in Linux uses two constants (PFN shift
and vring alignment) for the interface, so update qemu to match.
I've tested this with PowerPC KVM and confirmed that it fixes virtio problems
when using non-TARGET_PAGE_SIZE pages in the guest.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5871 c046a42c-6fe2-441c-8c8c-71466251a162
Virtio-blk is a paravirtual block device based on VirtIO. It can be used by
specifying the if=virtio parameter to the -drive parameter.
When using -enable-kvm, it can achieve very good performance compared to IDE or
SCSI.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5870 c046a42c-6fe2-441c-8c8c-71466251a162
This patch adds core support for VirtIO. VirtIO is a paravirtualization
framework that has been in Linux since 2.6.21. A PCI transport has been
available since 2.6.25. Network drivers are also available for Windows.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5869 c046a42c-6fe2-441c-8c8c-71466251a162
This PCI controller can be found on a number of 4xx SoCs, including the 440EP.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Acked-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5862 c046a42c-6fe2-441c-8c8c-71466251a162
When command is not DMA, TCMID and TCLO registers are not filled. Use command buffer len instead
Signed-off-by: Herve Poussineau <hpoussin@reactos.org>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5813 c046a42c-6fe2-441c-8c8c-71466251a162
According to http://www.ibiblio.org/pub/historic-linux/early-ports/Sparc/NCR/NCR53C9X.txt,
"Any bit pattern written to this register may be read back and should be identical"
Signed-off-by: Herve Poussineau <hpoussin@reactos.org>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5812 c046a42c-6fe2-441c-8c8c-71466251a162
- Fix internal fifo size (16 bytes), according to http://www.ibiblio.org/pub/historic-linux/early-ports/Sparc/NCR/NCR53C9X.txt
- Fix values of STAT_MI and STAT_MO
- Give a scsi ID to adapter, and prevent this ID to be used by devices
- Prevent fifo overrun in esp_mem_writeb
- Add a ESP_ERROR macro, and use it where appropriate
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5811 c046a42c-6fe2-441c-8c8c-71466251a162
Virtio will want to use the geometry detection code. It doesn't belong
in ide.c anyway.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5797 c046a42c-6fe2-441c-8c8c-71466251a162
Hypervisors like KVM perform badly while doing mmio on
a loop, because it'll generate an exit on each access.
This is the case with VGA, which results in very bad
performance.
In this patch, we map the linear frame buffer as RAM,
make sure it has dirty region tracking enabled, and then
just let the region to be written.
Cleanups suggestions by:
Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Glauber Costa <glommer@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5793 c046a42c-6fe2-441c-8c8c-71466251a162
It'll be reused later by the vga optimization.
Signed-off-by: Glauber Costa <glommer@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5791 c046a42c-6fe2-441c-8c8c-71466251a162
unsigned long is too bad of a type. Use ram_addr_t instead.
aligurori: fixed a compile warning in this patch
Signed-off-by: Glauber Costa <glommer@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5790 c046a42c-6fe2-441c-8c8c-71466251a162
This patches makes SH serial emulation use qemu_irq in its interface.
* hw/sh.h (sh_serial_init): Take qemu_irq, not intc_source.
* hw/sh7750.c (sh7750_init): Adjust.
* hw/sh_intc.c (sh_intc_set_irq): Don't assert or deassert
irq more than once.
* hw/sh_serial.c (sh_serial_state): Use qemu_irq, not intc_source.
(sh_serial_clear_fifo, sh_serial_ioport_write)
(sh_serial_receive_byte): Adjust.
(sh_serial_init): Take qemu_irq, not intc_source.
(Vladimir Prus)
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5769 c046a42c-6fe2-441c-8c8c-71466251a162
We're currently ignoring the e1000 VLAN tagging, stripping and filtering
features in the e1000 emulation. This patch adds backing for the
relevant registers and provides a software implementation of the
acceleration, such that a guest can make use of VLANs.
This is mostly (only?) useful for a guest on a bridge (not user mode
networking). The only caveat beyond that is that you need to make sure
the host NIC isn't doing it's own tagging, stripping, or filtering.
This generally means the host NIC on the bridge should not be part of a
VLAN.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5766 c046a42c-6fe2-441c-8c8c-71466251a162
u-boot is a firmware. uImage is an executable file format.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5764 c046a42c-6fe2-441c-8c8c-71466251a162
