Now that the OpenPIC is wired up via the board, we can now remove our temporary
PIC qdev pointer property and replace it with an object link instead.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Instead wire up the PCI/AGP host bridges in mac_newworld.c. Now this is complete
it is possible to move the initialisation of the PCI hole alias into
pci_u3_agp_init().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Instead wire up the PCI/AGP host bridges in mac_newworld.c. Now this is complete
it is possible to move the initialisation of the PCI hole alias into
pci_unin_main_init().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Somewhere in the history of time, the initialisation of the PCI buses for the
AGP and PCI host bridges got mixed up in that the PCI host bridge was
creating an instance of the AGP PCI bus, and the AGP PCI bus was missing.
Swap the PCI host bridge over to use the correct PCI bus (including setting
the kMacRISCPCIAddressSelect register used by MacOS X) and add the missing
reference to the AGP PCI bus.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Since the IO address space is fixed to use the standard system IO address
space then we can also use the opportunity to remove the address_space_io
parameter from pci_pmac_init() and pci_pmac_u3_init().
Note we also move the default mac99 PCI bus to the end of the initialisation
list so that it becomes the default destination for any devices specified
via -device without an explicit PCI bus provided.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is in preparation for moving the PCI bus wiring inside the uninorth
host bridge devices. In the future it will be possible to remove this once the
PICs have been switched to use qdev GPIOs.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Whilst we are here, rename the memory regions to better reflect whether they
belong to either a PCI or an AGP bus.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Since the macio device has a link to the PIC device, we can now wire up the
IRQs directly via qdev GPIOs rather than having to use an intermediate array.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Introduce constants for the pre-defined Old World IRQs to help keep things
readable.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This simplifies the Old World machine to simply mapping the ISA memory region
into the main address space.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Instead wire up the grackle device inside the Mac Old World machine.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is the first step towards removing the old-style pci_grackle_init()
function. Following on from the previous commit we can now pass the heathrow
device as an object link and wire up the heathrow IRQs via qdev GPIOs.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Instead wire up heathrow to the CPU and grackle PCI host using qdev GPIOs.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is in preparation for moving the device wiring into the New World machine.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
[dwg: Added hw/hw.h #include as suggested by Philippe Mathieu-Daudé]
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
After QOMification this is clearly no longer needed (and possibly hasn't been
for some time).
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Commit 593c181160: "PPC: Newworld: Add second uninorth control register set"
added a second set of uninorth registers at 0xf3000000.
Testing MacOS 9.2 to MacOS X 10.4 reveals no accesses to this address and I
can't find any reference to it in Apple's Core99.cpp source so I'm assuming
that this was the result of another bug that has now been fixed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This makes sure we keep patchew/checkpatch happy during the remainder of this
patchset.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
-----BEGIN PGP SIGNATURE-----
iQFUBAABCAA+FiEEVZrkbC1rbTJl58uh4+M5I0i1DTkFAlriFkogHGlqYWNrc29u
QGNoaWFyay5ncmVlbmVuZC5vcmcudWsACgkQ4+M5I0i1DTnRkgf7BJhxaGrtOfsR
pM1p/SAAq5LoivCtglk7h5veSykPWbHJZb0QMHZGJiksQ+7p8+/mpZ4W9vQRpkqP
Tw54Of8mPGhMBxZ2dikw8WhUsP7efjPPmTZOHR85CSNZe06jnMsYXCUrfc3HyZ/T
eOoU4+RJw8uZYW/e8CMf5RFe55zXWsZyI1bGkTwuDPr4ilyEvMQ9WFSXZt0PdBFV
8FvA+xY8J/DZkLSsFlPFYycyCVkSl4HXOHjBsgDc5ggfo32QXI6Isku1eOaZ/15N
ydCnn02yRnNhkIamPEl8UQMu4wrHCDj5HMRvy+TyDO/GVq0HAm/hOBFeYnQvLCZu
fkN2q2wUng==
=1ON4
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/iwj/tags/for-upstream.depriv-2' into staging
xen: xen-domid-restrict improvements
# gpg: Signature made Thu 26 Apr 2018 19:11:22 BST
# gpg: using RSA key E3E3392348B50D39
# gpg: Good signature from "Ian Jackson (new general purpose key) <ijackson@chiark.greenend.org.uk>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 559A E46C 2D6B 6D32 65E7 CBA1 E3E3 3923 48B5 0D39
* remotes/iwj/tags/for-upstream.depriv-2:
configure: do_compiler: Dump some extra info under bash
os-posix: cleanup: Replace perror with error_report
os-posix: cleanup: Replace fprintf with error_report in remaining call sites
xen: Expect xenstore write to fail when restricted
xen: Remove now-obsolete xen_xc_domain_add_to_physmap
xen: Use newly added dmops for mapping VGA memory
os-posix: Provide new -runas <uid>:<gid> facility
os-posix: cleanup: Replace fprintfs with error_report in change_process_uid
xen: destroy_hvm_domain: Try xendevicemodel_shutdown
xen: move xc_interface compatibility fallback further up the file
xen: destroy_hvm_domain: Move reason into a variable
xen: defer call to xen_restrict until just before os_setup_post
xen: restrict: use xentoolcore_restrict_all
xen: link against xentoolcore
AccelClass: Introduce accel_setup_post
checkpatch: Add xendevicemodel_handle to the list of types
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This makes it much easier to find a particular thing in config.log.
We have to use the ${BASH_LINENO[*]} syntax which is a syntax error in
other shells, so test what shell we are running and use eval.
The extra output is only printed if configure is run with bash. On
systems where /bin/sh is not bash, it is necessary to say bash
./configure to get the extra debug info in the log.
Suggested-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Ian Jackson <Ian.Jackson@eu.citrix.com>
CC: Kent R. Spillner <kspillner@acm.org>
CC: Janosch Frank <frankja@linux.vnet.ibm.com>
CC: Thomas Huth <thuth@redhat.com>
CC: Peter Maydell <peter.maydell@linaro.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
perror() is defined to fprintf(stderr,...). HACKING says
fprintf(stderr,...) is wrong. So perror() is too.
Signed-off-by: Ian Jackson <Ian.Jackson@eu.citrix.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Markus Armbruster <armbru@redhat.com>
CC: Daniel P. Berrange <berrange@redhat.com>
CC: Michael Tokarev <mjt@tls.msk.ru>
CC: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Ian Jackson <Ian.Jackson@eu.citrix.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Markus Armbruster <armbru@redhat.com>
CC: Daniel P. Berrange <berrange@redhat.com>
CC: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Saving the current state to xenstore may fail when running restricted
(in particular, after a migration). Therefore, don't report the error or
exit when running restricted. Toolstacks that want to allow running
QEMU restricted should instead make use of QMP events to listen for
state changes.
CC: Ian Jackson <ian.jackson@eu.citrix.com>
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Ian Jackson <ian.jackson@eu.citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
The last user was just removed; remove this function, accordingly.
Signed-off-by: Ian Jackson <Ian.Jackson@eu.citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Xen unstable (to be in 4.11) has two new dmops, relocate_memory and
pin_memory_cacheattr. Use these to set up the VGA memory, replacing the
previous calls to libxc. This allows the VGA console to work properly
when QEMU is running restricted (-xen-domid-restrict).
Wrapper functions are provided to allow QEMU to work with older versions
of Xen.
Tweak the error handling while making this change:
* Report pin_memory_cacheattr errors.
* Report errors even when DEBUG_HVM is not set. This is useful for
trying to understand why VGA is not working, since otherwise it just
fails silently.
* Fix the return values when an error occurs. The functions now
consistently return -1 and set errno.
CC: Ian Jackson <ian.jackson@eu.citrix.com>
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Ian Jackson <ian.jackson@eu.citrix.com>
Signed-off-by: Ian Jackson <ian.jackson@eu.citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
This allows the caller to specify a uid and gid to use, even if there
is no corresponding password entry. This will be useful in certain
Xen configurations.
We don't support just -runas <uid> because: (i) deprivileging without
calling setgroups would be ineffective (ii) given only a uid we don't
know what gid we ought to use (since uids may eppear in multiple
passwd file entries with different gids).
Signed-off-by: Ian Jackson <Ian.Jackson@eu.citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Markus Armbruster <armbru@redhat.com>
CC: Daniel P. Berrange <berrange@redhat.com>
CC: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
I'm going to be editing this function and it makes sense to clean up
this style problem in advance.
Signed-off-by: Ian Jackson <Ian.Jackson@eu.citrix.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Markus Armbruster <armbru@redhat.com>
CC: Daniel P. Berrange <berrange@redhat.com>
CC: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
xc_interface_open etc. is not going to work if we have dropped
privilege, but xendevicemodel_shutdown will if everything is new
enough.
xendevicemodel_shutdown is only availabe in Xen 4.10 and later, so
provide a stub for earlier versions.
Signed-off-by: Ian Jackson <Ian.Jackson@eu.citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
We are going to want to use the dummy xendevicemodel_handle type in
new stub functions in the CONFIG_XEN_CTRL_INTERFACE_VERSION < 41000
section. So we need to provide that definition, or (as applicable)
include the appropriate header, earlier in the file.
(Ideally the newer compatibility layers would be at the bottom of the
file, so that they can naturally benefit from the compatibility layers
for earlier version. But that's rather too much for this series.)
No functional change.
Signed-off-by: Ian Jackson <Ian.Jackson@eu.citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
We are going to want to reuse this.
No functional change.
Signed-off-by: Ian Jackson <Ian.Jackson@eu.citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
We need to restrict *all* the control fds that qemu opens. Looking in
/proc/PID/fd shows there are many; their allocation seems scattered
throughout Xen support code in qemu.
We must postpone the restrict call until roughly the same time as qemu
changes its uid, chroots (if applicable), and so on.
There doesn't seem to be an appropriate hook already. The RunState
change hook fires at different times depending on exactly what mode
qemu is operating in.
And it appears that no-one but the Xen code wants a hook at this phase
of execution. So, introduce a bare call to a new function
xen_setup_post, just before os_setup_post. Also provide the
appropriate stub for when Xen compilation is disabled.
We do the restriction before rather than after os_setup_post, because
xen_restrict may need to open /dev/null, and os_setup_post might have
called chroot.
Currently this does not work with migration, because when running as
the Xen device model qemu needs to signal to the toolstack that it is
ready. It currently does this using xenstore, and for incoming
migration (but not for ordinary startup) that happens after
os_setup_post.
It is correct that this happens late: we want the incoming migration
stream to be processed by a restricted qemu. The fix for this will be
to do the startup notification a different way, without using
xenstore. (QMP is probably a reasonable choice.)
So for now this restriction feature cannot be used in conjunction with
migration. (Note that this is not a regression in this patch, because
previously the -xen-restrict-domid call was, in fact, simply
ineffective!) We will revisit this in the Xen 4.11 release cycle.
Signed-off-by: Ian Jackson <Ian.Jackson@eu.citrix.com>
CC: Paolo Bonzini <pbonzini@redhat.com> (maintainer:X86)
CC: Richard Henderson <rth@twiddle.net> (maintainer:X86)
CC: Eduardo Habkost <ehabkost@redhat.com> (maintainer:X86)
CC: Michael S. Tsirkin <mst@redhat.com> (supporter:PC)
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
And insist that it works.
Drop individual use of xendevicemodel_restrict and
xenforeignmemory_restrict. These are not actually effective in this
version of qemu, because qemu has a large number of fds open onto
various Xen control devices.
The restriction arrangements are still not right, because the
restriction needs to be done very late - after qemu has opened all of
its control fds.
xentoolcore_restrict_all and xentoolcore.h are available in Xen 4.10
and later, only. Provide a compatibility stub. And drop the
compatibility stubs for the old functions.
Signed-off-by: Ian Jackson <Ian.Jackson@eu.citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
Xen libraries in 4.10 include a new xentoolcore library. This
contains the xentoolcore_restrict_all function which we are about to
want to use.
Signed-off-by: Ian Jackson <Ian.Jackson@eu.citrix.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
This is called just before os_setup_post. Currently none of the
accelerators provide this hook, but the Xen one is going to provide
one in a moment.
Signed-off-by: Ian Jackson <Ian.Jackson@eu.citrix.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
This avoids checkpatch misparsing (as statements) long function
definitions or declarations, which sometimes start with constructs
like this:
static inline int xendevicemodel_relocate_memory(
xendevicemodel_handle *dmod, domid_t domid, ...
The type xendevicemodel_handle does not conform to Qemu CODING_STYLE,
which would suggest CamelCase. However, it is a type defined by the
Xen Project in xen.git. It would be possible to introduce a typedef
to allow the qemu code to refer to it by a differently-spelled name,
but that would obfuscate more than it would clarify.
CC: Eric Blake <eblake@redhat.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Ian Jackson <Ian.Jackson@eu.citrix.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Create a new function serial_max_hds() which returns the number of
serial ports defined by the user. This is needed only by spapr.
This allows us to remove the MAX_SERIAL_PORTS define.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180420145249.32435-14-peter.maydell@linaro.org
Instead of having a fixed sized global serial_hds[] array,
use a local dynamically reallocated one, so we don't have
a compile time limit on how many serial ports a system has.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180420145249.32435-13-peter.maydell@linaro.org
The superio device has a limit on the number of serial
ports it supports which is really only there because
it has a fixed-size array serial[]. This limit isn't
related particularly to the global MAX_SERIAL_PORTS limit,
so use a different #define for it.
(In practice the users of superio only ever want 2 serial ports.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180420145249.32435-12-peter.maydell@linaro.org
The ISA serial port handling in serial-isa.c imposes a limit
of 4 serial ports. This is because we only know of 4 IO port
and IRQ settings for them, and is unrelated to the generic
MAX_SERIAL_PORTS limit, though they happen to both be set at
4 currently.
Use a new MAX_ISA_SERIAL_PORTS wherever that is the correct
limit to be checking against.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180420145249.32435-11-peter.maydell@linaro.org
The handling of NULL chardevs in exynos4210_uart_create() is now
all unnecessary: we don't need to create 'null' chardevs, and we
don't need to enforce a bounds check on serial_hd().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180420145249.32435-10-peter.maydell@linaro.org
Remove checks on MAX_SERIAL_PORTS that were just checking whether
they were within bounds for the serial_hds[] array and falling
back to NULL if not. This isn't needed with the serial_hd()
function, which returns NULL for all indexes beyond what the
user set up.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180420145249.32435-9-peter.maydell@linaro.org
Change all the uses of serial_hds[] to go via the new
serial_hd() function. Code change produced with:
find hw -name '*.[ch]' | xargs sed -i -e 's/serial_hds\[\([^]]*\)\]/serial_hd(\1)/g'
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180420145249.32435-8-peter.maydell@linaro.org
Provide an accessor function serial_hd() to return the Chardev
(if any) associated with the numbered serial port. This will
be used to replace direct accesses to the serial_hds[] array,
so that calling code doesn't need to care about the size of
that array.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180420145249.32435-7-peter.maydell@linaro.org
Following commit 12051d82f0, UART devices should handle
being passed a NULL pointer chardev, so we don't need to
create "null" backends in board code. Remove the code that
does this and updates serial_hds[].
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180420145249.32435-6-peter.maydell@linaro.org
Following commit 12051d82f0, UART devices should handle
being passed a NULL pointer chardev, so we don't need to
create "null" backends in board code. Remove the code that
does this and updates serial_hds[].
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180420145249.32435-5-peter.maydell@linaro.org
Following commit 12051d82f0, UART devices should handle
being passed a NULL pointer chardev, so we don't need to
create "null" backends in board code. Remove the code that
does this and updates serial_hds[].
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180420145249.32435-4-peter.maydell@linaro.org
Following commit 12051d82f0, UART devices should handle
being passed a NULL pointer chardev, so we don't need to
create "null" backends in board code. Remove the code that
does this and updates serial_hds[].
(fsl-imx7.c was already written this way.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180420145249.32435-3-peter.maydell@linaro.org
Currently the serial.c realize code has an explicit check that it is not
connected to a disconnected backend (ie one with a NULL chardev).
This isn't what we want -- you should be able to create a serial device
even if it isn't attached to anything. Remove the check.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180420145249.32435-2-peter.maydell@linaro.org
