Also convert bdrv_pwrite_sync() to being implemented using
generated_co_wrapper.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20220609152744.3891847-9-afaria@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
bdrv_{pread,pwrite}() now return -EIO instead of -EINVAL when 'bytes' is
negative, making them consistent with bdrv_{preadv,pwritev}() and
bdrv_co_{pread,pwrite,preadv,pwritev}().
bdrv_pwrite_zeroes() now also calls trace_bdrv_co_pwrite_zeroes() and
clears the BDRV_REQ_MAY_UNMAP flag when appropriate, which it didn't
previously.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Message-Id: <20220609152744.3891847-8-afaria@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
For consistency with other I/O functions, and in preparation to
implement bdrv_{pread,pwrite}() using generated_co_wrapper.
unsigned int fits in int64_t, so all callers remain correct.
bdrv_check_request32() is called further down the stack and causes -EIO
to be returned if 'bytes' is negative or greater than
BDRV_REQUEST_MAX_BYTES, which in turns never exceeds SIZE_MAX.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Message-Id: <20220609152744.3891847-7-afaria@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
It does not mutate the buffer.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20220609152744.3891847-6-afaria@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
They currently return the value of their headerlen/buflen parameter on
success. Returning 0 instead makes it clear that short reads/writes are
not possible.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20220609152744.3891847-5-afaria@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
In 60592cfed2 ("hw/arm/virt: dt: add kaslr-seed property"), the
kaslr-seed property was added, but the equally as important rng-seed
property was forgotten about, which has identical semantics for a
similar purpose. This commit implements it in exactly the same way as
kaslr-seed. It then changes the name of the disabling option to reflect
that this has more to do with randomness vs determinism, rather than
something particular about kaslr.
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
[PMM: added deprecated.rst section for the deprecation]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This queue consists of improvements and bug fixes in TCG, powernv and
pSeries, with some fixes in other areas as well.
- tcg and target/ppc: BCDA and mffscdrn implementations, Remove CONFIG_INT128
conditional code
- fix '-cpu max' alias
- remove '-cpu default' alias
- spapr: fixes in DDW handling, H_WATCHDOG support
- powernv: cleanups in the pnv-phb3/4 models
- fix core type of MPC8555 and MPC8560 models
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQX6/+ZI9AYAK8oOBk82cqW3gMxZAUCYsXrpgAKCRA82cqW3gMx
ZBe9AP4oqMTFw7r9EQPJU4QFMUeAVABl4o0xNb2wLyYov9CtKAD+LoVERSmtLTJ1
kFpgBrRTWKVylaLEdZQoTdFlJeBwzQg=
=GPG1
-----END PGP SIGNATURE-----
Merge tag 'pull-ppc-20220706' of https://gitlab.com/danielhb/qemu into staging
ppc patch queue for 2022-07-06:
This queue consists of improvements and bug fixes in TCG, powernv and
pSeries, with some fixes in other areas as well.
- tcg and target/ppc: BCDA and mffscdrn implementations, Remove CONFIG_INT128
conditional code
- fix '-cpu max' alias
- remove '-cpu default' alias
- spapr: fixes in DDW handling, H_WATCHDOG support
- powernv: cleanups in the pnv-phb3/4 models
- fix core type of MPC8555 and MPC8560 models
# -----BEGIN PGP SIGNATURE-----
#
# iHUEABYKAB0WIQQX6/+ZI9AYAK8oOBk82cqW3gMxZAUCYsXrpgAKCRA82cqW3gMx
# ZBe9AP4oqMTFw7r9EQPJU4QFMUeAVABl4o0xNb2wLyYov9CtKAD+LoVERSmtLTJ1
# kFpgBrRTWKVylaLEdZQoTdFlJeBwzQg=
# =GPG1
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 07 Jul 2022 01:38:06 AM +0530
# gpg: using EDDSA key 17EBFF9923D01800AF2838193CD9CA96DE033164
# gpg: Good signature from "Daniel Henrique Barboza <danielhb413@gmail.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 17EB FF99 23D0 1800 AF28 3819 3CD9 CA96 DE03 3164
* tag 'pull-ppc-20220706' of https://gitlab.com/danielhb/qemu: (34 commits)
target/ppc: Fix MPC8555 and MPC8560 core type to e500v1
target/ppc/cpu-models: Remove the "default" CPU alias
target/ppc: Return default CPU for max CPU
target/ppc: implement cdtbcd
target/ppc: implement cbcdtd
target/ppc: implement addg6s
target/ppc: Add flag for ISA v2.06 BCDA instructions
tests/tcg/ppc64: Add mffsce test
target/ppc: Implement mffscdrn[i] instructions
target/ppc: Move mffs[.] to decodetree
target/ppc: Move mffsl to decodetree
target/ppc: Move mffsce to decodetree
target/ppc: Move mffscrn[i] to decodetree
target/ppc: Fix insn32.decode style issues
ppc/spapr: Implement H_WATCHDOG
ppc: Define SETFIELD for the ppc target
target/ppc: use int128.h methods in vsubcuq
target/ppc: use int128.h methods in vsubecuq and vsubeuqm
target/ppc: use int128.h methods in vsubuqm
target/ppc: use int128.h methods in vaddcuq
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The new PAPR 2.12 defines a watchdog facility managed via the new
H_WATCHDOG hypercall.
This adds H_WATCHDOG support which a proposed driver for pseries uses:
https://patchwork.ozlabs.org/project/linuxppc-dev/list/?series=303120
This was tested by running QEMU with a debug kernel and command line:
-append \
"pseries-wdt.timeout=60 pseries-wdt.nowayout=1 pseries-wdt.action=2"
and running "echo V > /dev/watchdog0" inside the VM.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220622051008.1067464-1-aik@ozlabs.ru>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
It keeps repeating, move it to the header. This uses __builtin_ffsll() to
allow using the macros in #define.
This is not using the QEMU's FIELD macros as this would require changing
all such macros found in skiboot (the PPC PowerNV firmware).
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220628080544.1509428-1-aik@ozlabs.ru>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
PAPR+/LoPAPR says:
===
The platform must restore the default DMA window for the PE on a call
to the ibm,remove-pe-dma-window RTAS call when all of the following
are true:
a. The call removes the last DMA window remaining for the PE.
b. The DMA window being removed is not the default window
===
This resets DMA as PAPR mandates.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220622052955.1069903-1-aik@ozlabs.ru>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
It is not advisable to execute an object_dynamic_cast() to poke into
bus->qbus.parent and follow it up with a C cast into the PnvPHB type we
think we got.
In fact this is not needed. There is nothing sophisticated being done
with the PHB object retrieved during root_port_realize() for both PHB3
and PHB4. We're retrieving a PHB reference just to access phb->chip_id
and phb->phb_id and use them to define the chassis/slot of the root
port.
phb->phb_id is already being passed to pnv_phb_attach_root_port() via
the 'index' parameter. Let's also add a 'chip_id' parameter to this
function and assign chassis and slot right there. This will spare us
from the hassle of accessing the PHB object inside realize().
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Message-Id: <20220621173436.165912-4-danielhb413@gmail.com>
This commit wires up bootinfo's RNG seed attribute so that Linux VMs can
have their RNG seeded from the earliest possible time in boot, just like
the "rng-seed" device tree property on those platforms. The link
contains the corresponding Linux patch.
Link: https://lore.kernel.org/lkml/20220626111509.330159-1-Jason@zx2c4.com/
Based-on: <20220625152318.120849-1-Jason@zx2c4.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Message-Id: <20220626111804.330745-1-Jason@zx2c4.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
* Fix edk2/opensbi jobs to not run automatically by accident
* Improve timings in the migration qtest
* Remove libvixl disassembler
* Add ukrainian translation
* Require a recent version of libpng
-----BEGIN PGP SIGNATURE-----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=Q2vV
-----END PGP SIGNATURE-----
Merge tag 'pull-request-2022-07-05' of https://gitlab.com/thuth/qemu into staging
* Fix memory leak in test-cutils
* Fix edk2/opensbi jobs to not run automatically by accident
* Improve timings in the migration qtest
* Remove libvixl disassembler
* Add ukrainian translation
* Require a recent version of libpng
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEEJ7iIR+7gJQEY8+q5LtnXdP5wLbUFAmLECEkRHHRodXRoQHJl
# ZGhhdC5jb20ACgkQLtnXdP5wLbV7lxAAmEItM6PIoW58eWPzReKVH8LE2w3UlvOZ
# JQhNgJjuN23fqjUVkcT0yCfdNCz/nKvafHnxfHQnrAXyB5V5vU8ovBgSuWK2mcmD
# NTFK+/2x5lcsyBrOe3QoeD2g1r7+Os3AYVkdnN/t2HAMLwQyaoshKaMV/UHC9O/i
# Kle1svYRNyCgyXJgxaOdbVMBSLi/L9h2R5AaG31GIi9wnf0n8HDH/ONtmeIpN09g
# BlMeZqPhGJT+tpMvviif65/Za57Y9h/r+TOgEIIs00cWmxqaBmcXXN9qog2s0n7A
# nOm3ck2lpGJCQ6+sl6/Mphyr3X6nWHsxGrLDElS0Ba5bg6T/Xqfg2pBcb81Klkjc
# QcTdFPiMxKUczgpFq326sqiaVzMgys4vwnW5iPSd5swNzrkYKADAIreki5jyM3cH
# lohBG/ruOmg5xMkX2K6pra0iOAeCz44Ku/HTREfY1CTUgEQZJY4SZrMJSnmUTnM+
# EQCkDcmOsnFDaQazneCbo18l37cXOgEhH8VoGAOqg1aRjr7TNlsJzx87PoD+9zNR
# GEh7kp18ABRGik5ZACdLQ/HhhOJa8+UWsGCwCdeBGv/TVug1Byz0OUG0PxX3X5SV
# WwubeKyZcqzoH92SQI3jZGSmuGBySy9q51T2k8FjZvaDsPiUN/MLPspNezH1qj2B
# W7qEaqIyGmo=
# =Q2vV
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 05 Jul 2022 03:15:45 PM +0530
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [undefined]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [undefined]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* tag 'pull-request-2022-07-05' of https://gitlab.com/thuth/qemu:
include/qemu/host-utils: Remove unused code in the *_overflow wrappers
meson.build: Require a recent version of libpng
po: add ukrainian translation
disas: Remove libvixl disassembler
tests: use consistent bandwidth/downtime limits in migration tests
tests: increase migration test converge downtime to 30 seconds
tests: wait for migration completion before looking for STOP event
tests: wait max 120 seconds for migration test status changes
gitlab-ci: Extend timeout for ubuntu-20.04-s390x-all to 75m
gitlab: honour QEMU_CI variable in edk2/opensbi jobs
gitlab: tweak comments in edk2/opensbi jobs
gitlab: normalize indentation in edk2/opensbi rules
tests/fp: Do not build softfloat3 tests if TCG is disabled
tests: fix test-cutils leaks
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
In general loongarch ipi device, 32bit registers is emulated, however for
anysend/mailsend device only 64bit register access is supported. So separate
the ipi memory region into two regions, including 32 bits and 64 bits.
Signed-off-by: Xiaojuan Yang <yangxiaojuan@loongson.cn>
Message-Id: <20220705064901.2353349-2-yangxiaojuan@loongson.cn>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
According to commit cec07c0b61 the code in the #else paths was required
for GCC < 5.0 and Clang < 3.8. We don't support such old compilers
at all anymore, so we can remove these lines now. We keep the wrapper
function, though, since they are easier to read and help to make sure that
the parameters have the right types.
Message-Id: <20220701025132.303469-1-thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The disassembly via capstone should be superiour to our old vixl
sources nowadays, so let's finally cut this old disassembler out
of the QEMU source tree.
Message-Id: <20220603164249.112459-1-thuth@redhat.com>
Tested-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Loongarch pch msi intc connects to extioi controller, the range of irq
number is 64-255. Add a property for irqbase, so that we can compute
the irq offset from the view of pch_msi controller with the method:
msi vector (from view of upper extioi intc) - irqbase
Signed-off-by: Mao Bibo <maobibo@loongson.cn>
Message-Id: <20220701030740.2469162-1-maobibo@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The update makes it easier to find and specify devices.
They can only be found by device type name without the id field,
for example, devices of the same type have the same label.
The update also adds a head field,
which is useful for devices that support multiple heads,
such as virtio-gpu.
Signed-off-by: Jianxian Wen <jianxian.wen@verisilicon.com>
Signed-off-by: Lu Gao <lu.gao@verisilicon.com>
Message-Id: <4C23C17B8E87E74E906A25A3254A03F4018FC045B0@SHASXM06.verisilicon.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This introduces a really basic PECI controller that responses to
commands by always setting the response code to success and then raising
an interrupt to indicate the command is done. This helps avoid getting
hit with constant errors if the driver continuously attempts to send a
command and keeps timing out.
The AST2400 and AST2500 only included registers up to 0x5C, not 0xFC.
They supported PECI 1.1, 2.0, and 3.0. The AST2600 and AST1030 support
PECI 4.0, which includes more read/write buffer registers from 0x80 to
0xFC to support 64-byte mode.
This patch doesn't attempt to handle that, or to create a different
version of the controller for the different generations, since it's only
implementing functionality that is common to all generations.
The basic sequence of events is that the firmware will read and write to
various registers and then trigger a command by setting the FIRE bit in
the command register (similar to the I2C controller).
Then the firmware waits for an interrupt from the PECI controller,
expecting the interrupt status register to be filled in with info on
what happened. If the command was transmitted and received successfully,
then response codes from the host CPU will be found in the data buffer
registers.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-12-me@pjd.dev>
[ clg: s/sysbus_mmio_map/aspeed_mmio_map/ ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This commit adds support for DMA RX in slave mode while using the new
register set in the AST2600 and AST1030. This patch also pretty much
assumes packet mode is enabled, I'm not sure if this will work in DMA
step mode.
This is particularly useful for testing IPMB exchanges between Zephyr
and external devices, which requires multi-master I2C support and DMA in
the new register mode, because the Zephyr drivers from Aspeed use DMA in
the new mode by default. The Zephyr drivers are also using packet mode.
The typical sequence of events for receiving data in DMA slave + packet
mode is that the Zephyr firmware will configure the slave address
register with an address to receive on and configure the bus's function
control register to enable master mode and slave mode simultaneously at
startup, before any transfers are initiated.
RX DMA is enabled in the slave mode command register, and the slave RX
DMA buffer address and slave RX DMA buffer length are set. TX DMA is not
covered in this patch.
When the Aspeed I2C controller receives data from some other I2C master,
it will reset the I2CS_DMA_LEN RX_LEN value to zero, then buffer
incoming data in the RX DMA buffer while incrementing the I2CC_DMA_ADDR
address counter and decrementing the I2CC_DMA_LEN counter. It will also
update the I2CS_DMA_LEN RX_LEN value along the way.
Once all the data has been received, the bus controller will raise an
interrupt indicating a packet command was completed, the slave address
matched, a normal stop condition was seen, and the transfer was an RX
operation.
If the master sent a NACK instead of a normal stop condition, or the
transfer timed out, then a slightly different set of interrupt status
values would be set. Those conditions are not handled in this commit.
The Zephyr firmware then collects data from the RX DMA buffer and clears
the status register by writing the PKT_MODE_EN bit to the status
register. In packet mode, clearing the packet mode interrupt enable bit
also clears most of the other interrupt bits automatically (except for a
few bits above it).
Note: if the master transmit or receive functions were in use
simultaneously with the slave mode receive functionality, then the
master mode functions may have raised the interrupt line for the bus
before the DMA slave transfer is complete. It's important to have the
slave's interrupt status register clear throughout the receive
operation, and if the slave attempts to raise the interrupt before the
master interrupt status is cleared, then it needs to re-raise the
interrupt once the master interrupt status is cleared. (And vice-versa).
That's why in this commit, when the master interrupt status is cleared
and the interrupt line is lowered, we call the slave interrupt _raise_
function, to see if the interrupt was pending. (And again, vice-versa).
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20220630045133.32251-8-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add slave mode functionality for the Aspeed I2C controller in old
register mode. This is implemented by realizing an I2C slave device
owned by the I2C controller and attached to its own bus.
The I2C slave device only implements asynchronous sends on the bus, so
slaves not supporting that will not be able to communicate with it.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
[ clg: checkpatch fixes ]
Message-Id: <20220601210831.67259-6-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-7-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add an asynchronous version of i2c_send() that requires the slave to
explicitly acknowledge on the bus with i2c_ack().
The current master must use the new i2c_start_send_async() to indicate
that it wants to do an asynchronous transfer. This allows the i2c core
to check if the target slave supports this or not. This approach relies
on adding a new enum i2c_event member, which is why a bunch of other
devices needs changes in their event handling switches.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Message-Id: <20220601210831.67259-5-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-6-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Allow slaves to master the bus by registering a bottom halve. If the bus
is busy, the bottom half is queued up. When a slave has succesfully
mastered the bus, the bottom half is scheduled.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
[ clg : - fixed typos in commit log ]
Message-Id: <20220601210831.67259-4-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-5-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
sysbus_mmio_map maps devices into "get_system_memory()".
With the new SoC memory attribute, we want to make sure that each device is
mapped into the SoC memory.
In single SoC machines, the SoC memory is the same as "get_system_memory()",
but in multi SoC machines it will be different.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220624003701.1363500-4-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Multi-SoC machines can use this property to specify a memory container
for each SoC. Single SoC machines will just specify get_system_memory().
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220624003701.1363500-3-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Currently, the Aspeed machines allocate a ram container region in
which the machine ram region is mapped. See commit ad1a978218
("aspeed: add a RAM memory region container"). An extra region is
mapped after ram in the ram container to catch invalid access done by
FW. That's how FW determines the size of ram. See commit ebe31c0a8e
("aspeed: add a max_ram_size property to the memory controller").
Let's move all the logic under the SoC where it should be. It will
also ease the work on multi SoC support.
Reviewed-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20220623202123.3972977-1-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
v2: - add arguments to QEMUMachine constructor in test, to make it work
on arm in gitlab pipeline
- use bdrv_inc_in_flight() / bdrv_dec_in_flight() instead of direct
manipulation with bs->in_flight
- add new options for copy-before-write filter
- new trace points for NBD
- prefer unsigned type for some 'in_flight' fields
-----BEGIN PGP SIGNATURE-----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=ndKk
-----END PGP SIGNATURE-----
Merge tag 'pull-block-2022-06-14-v2' of https://gitlab.com/vsementsov/qemu into staging
Block jobs & NBD patches
v2: - add arguments to QEMUMachine constructor in test, to make it work
on arm in gitlab pipeline
- use bdrv_inc_in_flight() / bdrv_dec_in_flight() instead of direct
manipulation with bs->in_flight
- add new options for copy-before-write filter
- new trace points for NBD
- prefer unsigned type for some 'in_flight' fields
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCgAdFiEEi5wmzbL9FHyIDoahVh8kwfGfefsFAmK8BqkACgkQVh8kwfGf
# efuiMw/+P9FFLfGFSjVP+LYeT0Ah6kN1ypCMQzIk3Qq/J6qgMZhtRqpQoZOfIFQL
# U9fGmEtQZ7gvEMD/nJToL6uOYlnQfPxDcA6GrRwWWE3rcFiPK4J0q2LlnPLn4QaU
# W/qag5l/QnZfLlj/iV6neWOEvqdnvY1L8IS+T8xV6N0iBYlwgMC/6FGshQwehzcV
# T5F1qPGB0vjFDjf92LFPEsvsFFHjHIVPwOyJMvF64QtSk57utikq/la9PI/yA9AH
# Ll4mNQuZKx6rSI5wE6b21jc8iOUvaoHdPSEDQZfNILSdgGdiKvFwE51y+baGnIAD
# TpjxfG59q0jyGxMjQVxMRSFaxAC4+Mqi82diSPv4xbiUdsE4byJH0oENn4z7+wAv
# EvjuU9yx4FfHHltoUNwfn2pv00o/ELdZIoBNmW36rPxSGZMvfVfRtuBL7XWNUFbW
# Fr4BwsjC4KfIxb16QTBGhXVv6grxdlwoU9N23npdi0YpW1ftZzXGDa85+gINQ807
# eK/gP/OtYPwIql0bgmLiuaRNzC9psmQOO6vQbdvd/e4BEVWkxiez37+e+zFMStmL
# OAL8rS6jckUoxVZjCYFEWg97XOobLUIhQxt9Fwh2omMDGKTwv861ghUAivxSWs93
# IRNxfwqNPxnpDDXjnK1ayZgU08IL98AUYVKcPN1y8JvEhB4Hr1k=
# =ndKk
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 29 Jun 2022 01:30:41 PM +0530
# gpg: using RSA key 8B9C26CDB2FD147C880E86A1561F24C1F19F79FB
# gpg: Good signature from "Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>" [unknown]
# gpg: aka "Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 8B9C 26CD B2FD 147C 880E 86A1 561F 24C1 F19F 79FB
* tag 'pull-block-2022-06-14-v2' of https://gitlab.com/vsementsov/qemu:
block: use 'unsigned' for in_flight field on driver state
nbd: trace long NBD operations
iotests: copy-before-write: add cases for cbw-timeout option
block/copy-before-write: implement cbw-timeout option
block/block-copy: block_copy(): add timeout_ns parameter
util: add qemu-co-timeout
iotests: add copy-before-write: on-cbw-error tests
block/copy-before-write: add on-cbw-error open parameter
block/copy-before-write: refactor option parsing
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Add possibility to limit block_copy() call in time. To be used in the
next commit.
As timed-out block_copy() call will continue in background anyway (we
can't immediately cancel IO operation), it's important also give user a
possibility to pass a callback, to do some additional actions on
block-copy call finish.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@openvz.org>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Add new API, to make a time limited call of the coroutine.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@openvz.org>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
xen_piix_pci_write_config_client() is implemented in the xen sub tree and
uses PIIX constants internally, thus creating a direct dependency on
PIIX. Now that xen_set_pci_link_route() is stubbable, the logic of
xen_piix_pci_write_config_client() can be moved to PIIX which resolves
the dependency.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <20220626094656.15673-3-shentey@gmail.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The only user of xen_set_pci_link_route() is
xen_piix_pci_write_config_client() which implements PIIX-specific logic in
the xen namespace. This makes xen-hvm depend on PIIX which could be
avoided if xen_piix_pci_write_config_client() was implemented in PIIX. In
order to do this, xen_set_pci_link_route() needs to be stubbable which
this patch addresses.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <20220626094656.15673-2-shentey@gmail.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
pi440fx_state is an out-parameter which is never read by the caller.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220612192800.40813-1-shentey@gmail.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
It always returns IOVA_OK so nobody uses it.
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20220427154931.3166388-1-eperezma@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This will be used for implementing the xtensa select_one
system call. Choose "poll" over "select" so that we can
reuse Glib's g_poll constants and to avoid struct timeval.
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This function has been replaced by *_write.
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This function has been replaced by *_write.
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
For arm-compat, initialize console_{in,out}_gf;
otherwise, initialize stdio file descriptors.
This will go some way to cleaning up arm-compat, and
will allow other semihosting to use normal stdio.
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Add a GuestFDType for connecting to the semihosting console.
Hook up to read, write, isatty, and fstat syscalls.
Note that the arm-specific syscall flen cannot be applied
to the console, because the console is not a descriptor
exposed to the guest.
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Will replace qemu_semihosting_console_{outs,outc},
but we need more plumbing first.
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Rename qemu_semihosting_connect_chardevs to
qemu_semihosting_chardev_init; pass the result
directly to qemu_semihosting_console_init.
Store the chardev in SemihostingConsole instead
of SemihostingConfig, which lets us drop
semihosting_get_chardev.
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Allow more than one character to be read at one time.
Will be used by m68k and nios2 semihosting for stdio.
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We don't need CPUArchState, and we do want the CPUState of the
thread performing the operation -- use this instead of current_cpu.
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
