Create a new "unimplemented" sysbus device, which simply accepts
all read and write accesses, and implements them as read-as-zero,
write-ignored, with logging of the access as LOG_UNIMP.
This is useful for stubbing out bits of an SoC or board model
which haven't been written yet.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1484247815-15279-3-git-send-email-peter.maydell@linaro.org
In BE32 mode, sub-word size watchpoints can fail to trigger because the
address of the access is adjusted in the opcode helpers before being
compared with the watchpoint registers. This patch reverses the address
adjustment before performing the comparison with the help of a new CPUClass
hook.
This version of the patch augments and tidies up comments a little.
Signed-off-by: Julian Brown <julian@codesourcery.com>
Message-id: caaf64ffc72f6ae183015337b7afdbd4b8989cb6.1484929304.git.julian@codesourcery.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Thumb-1 code has some issues in BE32 mode (as currently implemented). In
short, since bytes are swapped within words at load time for BE32
executables, this also swaps pairs of adjacent Thumb-1 instructions.
This patch un-swaps those pairs of instructions again, both for execution,
and for disassembly. (The previous version of the patch always read four
bytes in arm_read_memory_func and then extracted the proper two bytes,
in a probably misguided attempt to match the behaviour of actual hardware
as described by e.g. the ARM9TDMI TRM, section 3.3 "Endian effects for
instruction fetches". It's less complicated to just read the correct
two bytes though.)
Signed-off-by: Julian Brown <julian@codesourcery.com>
Message-id: ca20462a044848000370318a8bd41dd0a4ed273f.1484929304.git.julian@codesourcery.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This enables reboot of a guest from U-Boot and Linux.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 1485452251-1593-3-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed SoC includes a set of watchdog timers using 32-bit
decrement counters, which can be based either on the APB clock or
a 1 MHz clock.
The watchdog timer is designed to prevent system deadlock and, in
general, it should be restarted before timeout. When a timeout occurs,
different types of signals can be generated, ARM reset, SOC reset,
System reset, CPU Interrupt, external signal or boot from alternate
block. The current model only performs the system reset function as
this is used by U-Boot and Linux.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Message-id: 1485452251-1593-2-git-send-email-clg@kaod.org
[clg: - fixed compile breakage
- fixed io region size
- added watchdog_perform_action() on timer expiry
- wrote a commit log
- merged fixes from Andrew Jeffery to scale the reload value ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The qdev id of a device can be huge if it's on the end of a chain
of bridges; in reality such chains shouldn't occur but they can
be made to by chaining PCIe bridges together.
The migration format has a number of 256 character long format
limits; check we don't hit them (we already use pstrcat/cpy but
that just protects us from buffer overruns, we fairly quickly
hit an assert).
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20170202125956.21942-3-dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
I'll be adding an error to it in a subsequent patch.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20170202125956.21942-2-dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <1485207141-1941-3-git-send-email-quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Windows 10 reportedly sends these, so accept them in case
the device in question is a superspeed (usb3) device.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1485870727-21956-2-git-send-email-kraxel@redhat.com
This obsoletes ppc-for-2.9-20170112, which had a MacOS build bug.
This is a long overdue ppc pull request for qemu-2.9. It's been a
long time coming due to some holidays and inconveniently timed
problems with testing. So, there's a lot in here:
* More POWER9 instruction implementations for TCG
* The simpler parts of my CPU compatibility mode cleanup
* This changes behaviour to prefer compatibility modes over
"raW" mode for new machine type versions
* New "40p" machine type which is essentially a modernized and
cleaned up "prep". The intention is that it will replace "prep"
once it has some more testing and polish.
* Add pseries-2.9 machine type
* Implement H_SIGNAL_SYS_RESET hypercall
* Consolidate the two alternate CPU init paths in pseries by
making it always go through CPU core objects to initialize CPU
* A number of bugfixes and cleanups
* Stop the guest timebase when the guest is stopped under KVM.
This makes the guest system clock also stop when paused, which
matches the x86 behaviour.
* Some preliminary cleanups leading towards implementation of the
POWER9 MMU.
There are also some changes not strictly related to ppc code, but for
its benefit:
* Limit the pxi-expander-bridge (PXB) device to x86 guests only
(it's essentially a hack to work around historical x86
limitations)
* Some additions to the 128-bit math in host_utils, necessary for
some of the new instructions.
* Revise a number of qtests and enable them for ppc
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=vLVl
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.9-20170202' into staging
ppc patch queue 2017-02-02
This obsoletes ppc-for-2.9-20170112, which had a MacOS build bug.
This is a long overdue ppc pull request for qemu-2.9. It's been a
long time coming due to some holidays and inconveniently timed
problems with testing. So, there's a lot in here:
* More POWER9 instruction implementations for TCG
* The simpler parts of my CPU compatibility mode cleanup
* This changes behaviour to prefer compatibility modes over
"raW" mode for new machine type versions
* New "40p" machine type which is essentially a modernized and
cleaned up "prep". The intention is that it will replace "prep"
once it has some more testing and polish.
* Add pseries-2.9 machine type
* Implement H_SIGNAL_SYS_RESET hypercall
* Consolidate the two alternate CPU init paths in pseries by
making it always go through CPU core objects to initialize CPU
* A number of bugfixes and cleanups
* Stop the guest timebase when the guest is stopped under KVM.
This makes the guest system clock also stop when paused, which
matches the x86 behaviour.
* Some preliminary cleanups leading towards implementation of the
POWER9 MMU.
There are also some changes not strictly related to ppc code, but for
its benefit:
* Limit the pxi-expander-bridge (PXB) device to x86 guests only
(it's essentially a hack to work around historical x86
limitations)
* Some additions to the 128-bit math in host_utils, necessary for
some of the new instructions.
* Revise a number of qtests and enable them for ppc
# gpg: Signature made Thu 02 Feb 2017 01:40:16 GMT
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.9-20170202: (107 commits)
hw/ppc/pnv: Use error_report instead of hw_error if a ROM file can't be found
ppc/kvm: Handle the "family" CPU via alias instead of registering new types
target/ppc/mmu_hash64: Fix incorrect shift value in amr calculation
target/ppc/mmu_hash64: Fix printing unsigned as signed int
tcg/POWER9: NOOP the cp_abort instruction
target/ppc/debug: Print LPCR register value if register exists
target-ppc: Add xststdc[sp, dp, qp] instructions
target-ppc: Add xvtstdc[sp,dp] instructions
target-ppc: Add MMU model check for booke machines
ppc: switch to constants within BUILD_BUG_ON
target/ppc/cpu-models: Fix/remove bad CPU aliases
target/ppc: Remove unused POWERPC_FAMILY(POWER)
spapr: clock should count only if vm is running
ppc: Remove unused function cpu_ppc601_rtc_init()
target/ppc: Add pcr_supported to POWER9 cpu class definition
powerpc/cpu-models: rename ISAv3.00 logical PVR definition
target-ppc: Add xvcv[hpsp, sphp] instructions
target-ppc: Add xsmulqp instruction
target-ppc: Add xsdivqp instruction
target-ppc: Add xscvsdqp and xscvudqp instructions
...
# Conflicts:
# hw/pci-bridge/Makefile.objs
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
generic pci root port support
disable shpc by default
safer version of ARRAY_SIZE and QEMU_BUILD_BUG_ON
fixes and cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYkTwaAAoJECgfDbjSjVRpHHoIALlEhk7iZJvjJBiT0BQ51lGB
uU0fq+8H2G+WZoM83dpSv/pG1Ob6SZtiehsXWf+6Za+AgnU3STCZDXGKo9Jxs2EO
jp73puewWCq69VMyjGnGEWWh4bf41xjWYVrhVrY9LSz7u6hCM9sdWPRy/PGLSlLo
s3xgYefGdtol0S5qMdb4LOb2tfcdGYHADyMiERT994pmfZKrBMXlHlVM0jOo5ytw
zknRh4JwH+zZMQPczrvWUTjdxRE0UIUd4fFz9cRwX8F6zVpAbKAT2Ird2jGNlpyh
jQBX+sxXQR3u+mjZDxZBYbpxOZARUTriagAJPs343uIUCPOmvVXsluidF9bkU+A=
=ZBEs
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio, vhost, pci: fixes, features
generic pci root port support
disable shpc by default
safer version of ARRAY_SIZE and QEMU_BUILD_BUG_ON
fixes and cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Wed 01 Feb 2017 01:38:34 GMT
# gpg: using RSA key 0x281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (22 commits)
arm: add trailing ; after MISMATCH_CHECK
arm: better stub version for MISMATCH_CHECK
hw/pci: disable pci-bridge's shpc by default
vhost-user: delete chardev on cleanup
vhost: skip ROM sections
virtio: make virtio_should_notify static
pci: Convert msix_init() to Error and fix callers
hcd-xhci: check & correct param before using it
msix: Follow CODING_STYLE
hw/i386: check if nvdimm is enabled before plugging
hw/pcie: Introduce Generic PCI Express Root Port
hw/ioh3420: derive from PCI Express Root Port base class
hw/pcie: Introduce a base class for PCI Express Root Ports
intel_iommu: fix and simplify size calculation in process_device_iotlb_desc()
pci: mark ROMs read-only
ARRAY_SIZE: check that argument is an array
compiler: expression version of QEMU_BUILD_BUG_ON
compiler: rework BUG_ON using a struct
QEMU_BUILD_BUG_ON: use __COUNTER__
ppc: switch to constants within BUILD_BUG_ON
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>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=YkDp
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/elmarco/tags/chr-split-pull-request' into staging
# gpg: Signature made Tue 31 Jan 2017 19:32:40 GMT
# gpg: using RSA key 0xDAE8E10975969CE5
# gpg: Good signature from "Marc-André Lureau <marcandre.lureau@redhat.com>"
# gpg: aka "Marc-André Lureau <marcandre.lureau@gmail.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 87A9 BD93 3F87 C606 D276 F62D DAE8 E109 7596 9CE5
* remotes/elmarco/tags/chr-split-pull-request: (41 commits)
char: headers clean-up
char: move parallel chardev in its own file
char: move serial chardev to its own file
char: move pty chardev in its own file
char: move pipe chardev in its own file
char: move console in its own file
char: move stdio in its own file
char: move file chardev in its own file
char: move udp chardev in its own file
char: move socket chardev to its own file
char: move win-stdio into its own file
char: move win chardev base class in its own file
char: move fd chardev in its own file
char: move QIOChannel-related stuff to char-io.h
char: remove unused READ_RETRIES
char: rename and move to header CHR_READ_BUF_LEN
char: move ringbuf/memory to its own file
char: move mux to its own file
char: move null chardev to its own file
char: make null_chr_write() the default method
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The shpc component is optional while ACPI hotplug is used
for hot-plugging PCI devices into a PCI-PCI bridge.
Disabling the shpc by default will make slot 0 usable at boot time
and not only for hot-plug, without loosing any functionality.
Older machines will have shpc enabled for compatibility reasons.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
msix_init() reports errors with error_report(), which is wrong when
it's used in realize(). The same issue was fixed for msi_init() in
commit 1108b2f. In order to make the API change as small as possible,
leave the return value check to later patch.
For some devices(like e1000e, vmxnet3, nvme) who won't fail because of
msix_init's failure, suppress the error report by passing NULL error
object.
Bonus: add comment for msix_init.
CC: Jiri Pirko <jiri@resnulli.us>
CC: Gerd Hoffmann <kraxel@redhat.com>
CC: Dmitry Fleytman <dmitry@daynix.com>
CC: Jason Wang <jasowang@redhat.com>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Hannes Reinecke <hare@suse.de>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Alex Williamson <alex.williamson@redhat.com>
CC: Markus Armbruster <armbru@redhat.com>
CC: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The Generic Root Port behaves almost the same as the
Intel's IOH device with id 3420, without having
Intel specific attributes.
The device has two purposes:
(1) Can be used on both X86 and ARM machines.
(2) It will allow us to tweak the behaviour
(e.g add vendor-specific PCI capabilities)
- something that obviously cannot be done
on a known device.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Andrea Bolognani <abologna@redhat.com>
The 'base' PCI Express Root Port includes
the common code to be re-used for all
Root Ports implementations. Most of the code
was taken from the current implementation
of Intel's IOH 3420 Root Port.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It's a familiar pattern: some code uses ARRAY_SIZE, then refactoring
changes the argument from an array to a pointer to a dynamically
allocated buffer. Code keeps compiling but any ARRAY_SIZE calls now
return the size of the pointer divided by element size.
Let's add build time checks to ARRAY_SIZE before we allow more
of these in the code-base.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
QEMU_BUILD_BUG_ON uses a typedef in order to be safe
to use outside functions, but sometimes it's useful
to have a version that can be used within an expression.
Following what Linux does, introduce QEMU_BUILD_BUG_ON_ZERO
that return zero after checking condition at build time.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
There are theoretical concerns that some compilers might not trigger
build failures on attempts to define an array of size (x ? -1 : 1) where
x is a variable and make it a variable sized array instead. Let rewrite
using a struct with a negative bit field size instead as there are no
dynamic bit field sizes. This is similar to what Linux does.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Some headers use QEMU_BUILD_BUG_ON. This causes a problem
if the C file including that header happens to have
QEMU_BUILD_BUG_ON at the same line number.
Fix using a widely available extension: __COUNTER__.
If unavailable, provide a stub.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Those could probably be squashed with earlier patches, however I
couldn't easily identify them, test them or check if there are still
necessary on various platforms.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
This define is used by several character devices, place it in char
common header.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
A mechanical move, except that qemu_chr_write_all() needs to be declared
in char.h header to be used from chardev unit files.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Introduce rules in the top level Makefile that are able to generate
trace.[ch] files in every subdirectory which has a trace-events file.
The top level directory is handled specially, so instead of creating
trace.h, it creates trace-root.h. This allows sub-directories to
include the top level trace-root.h file, without ambiguity wrt to
the trace.g file in the current sub-dir.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170125161417.31949-7-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
All users include the trailing ; anyway, let's require that -
it seems cleaner.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
The class kind is necessary to lookup the chardev name in
qmp_chardev_add() after calling qemu_chr_new_from_opts() and to set
the appropriate ChardevBackend (mainly to free the right
fields).
qemu_chr_new_from_opts() can be changed to use a non-qmp function
using the chardev class typename. Introduce qemu_chardev_add() to be
called from qemu_chr_new_from_opts() and remove the class chardev kind
field. Set the backend->type in the parse callback (when non-common
fields are added).
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
CharDriver no longer exists, it has been replaced with Chardev.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
qemu_chr_new_from_opts() is modified to not need CharDriver backend[]
array, but uses instead objectified qmp_query_chardev_backends() and
char_get_class(). The alias field is moved outside in a ChardevAlias[],
similar to QDevAlias for devices.
"kind" and "parse" are moved to ChardevClass ("kind" is to be removed
next)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Now it uses Object instance_finalize instead.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
This enables the ps2 controller to process mouse events for buttons 4 and 5.
Additionally, distinct definitions for the ps2 mouse button state are
introduced. The legacy definitions from console.h are not used anymore.
Signed-off-by: Fabian Lesniak <fabian@lesniak-it.de>
Message-id: 20161206190007.7539-3-fabian@lesniak-it.de
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Implements 128-bit left shift and right shift as well as their
testcases. By design, shift silently mods by 128, so the caller is
responsible to assert the shift range if necessary.
Left shift sets the overflow flag if any non-zero digit is shifted out.
Examples:
ulshift(&low, &high, 250, &overflow);
equivalent: n << 122
urshift(&low, &high, -2);
equivalent: n << 126
Signed-off-by: Jose Ricardo Ziviani <joserz@linux.vnet.ibm.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
[dwg: Added test-shift128 to .gitignore]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
xscvdphp: VSX Scalar round & Convert Double-Precision format to
Half-Precision format
xscvhpdp: VSX Scalar Convert Half-Precision format to
Double-Precision format
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When passing through an USB storage device to a pseries guest, it
is currently not possible to automatically boot from the device
if the "bootindex" property has been specified, too (e.g. when using
"-device nec-usb-xhci -device usb-host,hostbus=1,hostaddr=2,bootindex=0"
at the command line). The problem is that QEMU builds a device tree path
like "/pci@800000020000000/usb@0/usb-host@1" and passes it to SLOF
in the /chosen/qemu,boot-list property. SLOF, however, probes the
USB device, recognizes that it is a storage device and thus changes
its name to "storage", and additionally adds a child node for the
SCSI LUN, so the correct boot path in SLOF is something like
"/pci@800000020000000/usb@0/storage@1/disk@101000000000000" instead.
So when we detect an USB mass storage device with SCSI interface,
we've got to adjust the firmware boot-device path properly that
SLOF can automatically boot from the device.
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1354177
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The H_SIGNAL_SYS_RESET hcall allows a guest CPU to raise a system reset
exception on CPUs within the same guest -- all CPUs, all-but-self, or a
specific CPU (including self).
This has not made its way to a PAPR release yet, but we have an hcall
number assigned.
H_SIGNAL_SYS_RESET = 0x380
Syntax:
hcall(uint64 H_SIGNAL_SYS_RESET, int64 target);
Generate a system reset NMI on the threads indicated by target.
Values for target:
-1 = target all online threads including the caller
-2 = target all online threads except for the caller
All other negative values: reserved
Positive values: The thread to be targeted, obtained from the value
of the "ibm,ppc-interrupt-server#s" property of the CPU in the OF
device tree.
Semantics:
- Invalid target: return H_Parameter.
- Otherwise: Generate a system reset NMI on target thread(s),
return H_Success.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr_h_cas_compose_response() includes a cpu_update parameter which
controls whether it includes updated information on the CPUs in the device
tree fragment returned from the ibm,client-architecture-support (CAS) call.
Providing the updated information is essential when CAS has negotiated
compatibility options which require different cpu information to be
presented to the guest. However, it should be safe to provide in other
cases (it will just override the existing data in the device tree with
identical data). This simplifies the code by removing the parameter and
always providing the cpu update information.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Currently the pseries machine has two paths for constructing CPUs. On
newer machine type versions, which support cpu hotplug, it constructs
cpu core objects, which in turn construct CPU threads. For older machine
versions it individually constructs the CPU threads.
This division is going to make some future changes to the cpu construction
harder, so this patch unifies them. Now cpu core objects are always
created. This requires some updates to allow core objects to be created
without a full complement of threads (since older versions allowed a
number of cpus not a multiple of the threads-per-core). Likewise it needs
some changes to the cpu core hot/cold plug path so as not to choke on the
old machine types without hotplug support.
For good measure, we move the cpu construction to its own subfunction,
spapr_init_cpus().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
The Xen HVM unplug protocol [1] specifies a mechanism to allow guests to
request unplug of 'aux' disks (which is stated to mean all IDE disks,
except the primary master). This patch adds support for that unplug request.
NOTE: The semantics of what happens if unplug of all disks and 'aux' disks
is simultaneously requests is not clear. The patch makes that
assumption that an 'all' request overrides an 'aux' request.
[1] http://xenbits.xen.org/gitweb/?p=xen.git;a=blob;f=docs/misc/hvm-emulated-unplug.markdown
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
----
Cc: Stefano Stabellini <sstabellini@kernel.org>
Cc: Anthony Perard <anthony.perard@citrix.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: John Snow <jsnow@redhat.com>
Turn Chardev into Object.
qemu_chr_alloc() is replaced by the qemu_chardev_new() constructor. It
will call qemu_char_open() to open/intialize the chardev with the
ChardevCommon *backend settings.
The CharDriver::create() callback is turned into a ChardevClass::open()
which is called from the newly introduced qemu_chardev_open().
"chardev-gdb" and "chardev-hci" are internal chardev and aren't
creatable directly with -chardev. Use a new internal flag to disable
them. We may want to use TYPE_USER_CREATABLE interface instead, or
perhaps allow -chardev usage.
Although in general we keep typename and macros private, unless the type
is being used by some other file, in this patch, all types and common
helper macros for qemu-char.c are in char.h. This is to help transition
now (some types must be declared early, while some aren't shared) and
when splitting in several units. This is to be improved later.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of registering a vc handler to allocate the Gtk VC Chardev,
overwrite the console.c char driver.
A later patch, when switching to QOM, will register a default console vc
QOM class if none has been registered before.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pick a uniform chardev type name.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use a single allocation for CharDriverState, this avoids extra
allocations & pointers, and is a step towards more object-oriented
CharDriver.
Gtk console is a bit peculiar, gd_vc_chr_set_echo() used to have a
temporary VirtualConsole to save the echo bit. Instead now, we consider
whether vcd->console is set or not, and restore the echo bit saved in
VCDriverState when calling gd_vc_vte_init().
The casts added are temporary, they are replaced with QOM type-safe
macros in a later patch in this series.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use a feature flag rather than a structure field for "replay".
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This allows to remove the "is_mux" field from CharDriverState.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This makes the code more declarative, and avoids duplicating the
information on all instances.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
No need to allocate & copy fields, let's use static const struct instead.
Add an alias field to the CharDriver structure to cover the cases where
we previously registered a driver twice under two names.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>