Commit 3885c2b463f6 ("MIPS: CM: Add support for reporting CM cache
errors") leads to Malta boards unconditionally reading CM GCRs upon bus
errors, regardless of whether a CM is present. This is incorrect & will
lead to further exceptions. Fix by moving the GCR reads to after the
check for whether a CM is present.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11186/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The documentation for mips_cm_is64 implied that the width of the CM GCRs
would change depending upon the CPU, which is not true. Reword the
explanation to be clearer that the GCR width is purely dependent upon
the version of the CM.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11185/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A boundary exists beyond which the timer frequency becomes high enough
that timer interrupts saturate the system and either cause it to slow to
a crawl or stop functioning entirely. Where that boundary lies depends
upon a number of factors such as the overhead of each interrupt and the
overall speed of the CPU, but correlates strongly with the clock
frequency at which the CPU runs. When running on emulators during
bringup or debug of a CPU that clock frequency is very low, which
results in the boundary at which the timer frequency becomes
unsustainable being very low. The current minimum of 48Hz pushes against
boundary in certain situations in current systems. Allow the kernel to
be configured for a 24Hz timer frequency in order to avoid problems on
such slow running systems.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11184/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Rather than #ifdef on CONFIG_KVM_GUEST & redefine the guest kseg0 base
locally, make use of the CAC_BASE macro which has the correct value in
both cases.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-kernel@vger.kernel.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11183/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The board code never sets up a leds-pwm device, so including the header
is not necessary.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11262/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Associate the PWM with the pwm-beeper device using a PWM lookup table.
This will eventually allow the legacy function calls to pwm_request() to
be removed from all consumer drivers.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11261/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
ARCH_USE_BUILTIN_BSWAP will use __builtin_bswap16(), __builtin_bswap32()
and __builtin_bswap64() where available. This allows better instruction
scheduling. On pre-R2 processors it will result in 32 bit and 64 bit
swapping being performed in a call to a __bswapsi2() rsp. __bswapdi2()
functions, so we add these, too.
For a 4.2 kernel with GCC 4.9 this yields the following kernel sizes:
text data bss dec hex filename
3996071 155804 88992 4240867 40b5e3 vmlinux ip22 baseline
3985687 159900 88992 4234579 409d53 vmlinux ip22 + bswap patch
6913157 378552 251024 7542733 7317cd vmlinux ip27 baseline
6878581 378552 251024 7508157 7290bd vmlinux ip27 + bswap patch
5773777 268752 187424 6229953 5f0fc1 vmlinux malta baseline
5773401 268752 187424 6229577 5f0e49 vmlinux malta + bswap patch
Presumably the code size improvments yield better cache hit rate thus
better performance compensating for the extra function call but this
will still need to be benchmarked.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When debugging or examining the performance of a system it can be useful
to examine the effect of L2 prefetching. Provide an optional debugfs
entry to allow a user to enable or disable L2 prefetching.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11182/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We have many extern declarations of mips_debugfs_dir through arch/mips/
in various C files. Unify them by declaring mips_debugfs_dir in a
header, including it in each affected C file & removing the duplicate
declarations.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-kernel@vger.kernel.org
Cc: Joe Perches <joe@perches.com>
Cc: Jaedon Shin <jaedon.shin@gmail.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: James Cowgill <James.Cowgill@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11181/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On systems with CM 2.5 & beyond there may be L2 prefetch units present
which are not enabled by default. Detect them, configuring & enabling
prefetching when available.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11180/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Introduce new functions in struct bcache_ops to enable & disable L2
cache prefetching, and to retrieve the current state of L2 prefetching.
This will be used in later patches.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11179/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When debugging it can be helpful to change the policy for compiler use
of MIPSr6 compact branches, in order to rule out or home in on their
involvement in bugs. Allow the GCC -mcompact-branches= flag to be set
via Kconfig under the "Kernel hacking" menu.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11178/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Unsigned values cannot be lesser than zero.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].
[ralf@linux-mips.org: Chris Dearman's original commit
9318c51acd9689505850152cc98277a6d6f2d752 ([MIPS] MIPS32/MIPS64 secondary
cache management) introduced these less than zero checks in 2.6.18.]
[1]: http://permalink.gmane.org/gmane.linux.kernel/2038576
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Cc: linux-kernel@vger.kernel.org
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Chris Dearman <chris.dearman@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11165/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All architectures must now define ioremap_uc(), but MIPS currently
only has ioremap_nocache().
Fixes: 4c73e8926623 ("arch/*/io.h: Add ioremap_uc() to all architectures")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11263/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some GCC versions (e.g. 4.8.3) can incorrectly inline a function with
MIPS32 instructions into another function with MIPS16 code [1], causing
the assembler to genereate incorrect binary code or fail right away
complaining about unrecognized opcode.
In the case of __arch_swab{16,32}, when inlined by the compiler with
flags `-mips32r2 -mips16 -Os', the assembler can fail with the following
error.
{standard input}:79: Error: unrecognized opcode `wsbh $2,$2'
For performance concerns and to workaround the issue already existing in
older compilers, just ignore these 2 functions when compiling with
mips16 enabled.
[1] Inlining nomips16 function into mips16 function can result in
undefined builtins, https://gcc.gnu.org/bugzilla/show_bug.cgi?id=55777
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11241/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This reverts commit e0d8b2ec532852d4b5aabcec3e7611848c32237d.
For at least GCC 4.8.3, adding nomips16 function attribute still cannot
prevent it from being inlined in mips16 context. So revert it first in
preparation for a better workaround.
[1] Inlining nomips16 function into mips16 function can result in
undefined builtins, https://gcc.gnu.org/bugzilla/show_bug.cgi?id=55777
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11240/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull strscpy string copy function implementation from Chris Metcalf.
Chris sent this during the merge window, but I waffled back and forth on
the pull request, which is why it's going in only now.
The new "strscpy()" function is definitely easier to use and more secure
than either strncpy() or strlcpy(), both of which are horrible nasty
interfaces that have serious and irredeemable problems.
strncpy() has a useless return value, and doesn't NUL-terminate an
overlong result. To make matters worse, it pads a short result with
zeroes, which is a performance disaster if you have big buffers.
strlcpy(), by contrast, is a mis-designed "fix" for strlcpy(), lacking
the insane NUL padding, but having a differently broken return value
which returns the original length of the source string. Which means
that it will read characters past the count from the source buffer, and
you have to trust the source to be properly terminated. It also makes
error handling fragile, since the test for overflow is unnecessarily
subtle.
strscpy() avoids both these problems, guaranteeing the NUL termination
(but not excessive padding) if the destination size wasn't zero, and
making the overflow condition very obvious by returning -E2BIG. It also
doesn't read past the size of the source, and can thus be used for
untrusted source data too.
So why did I waffle about this for so long?
Every time we introduce a new-and-improved interface, people start doing
these interminable series of trivial conversion patches.
And every time that happens, somebody does some silly mistake, and the
conversion patch to the improved interface actually makes things worse.
Because the patch is mindnumbing and trivial, nobody has the attention
span to look at it carefully, and it's usually done over large swatches
of source code which means that not every conversion gets tested.
So I'm pulling the strscpy() support because it *is* a better interface.
But I will refuse to pull mindless conversion patches. Use this in
places where it makes sense, but don't do trivial patches to fix things
that aren't actually known to be broken.
* 'strscpy' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: use global strscpy() rather than private copy
string: provide strscpy()
Make asm/word-at-a-time.h available on all architectures
Pull MIPS updates from Ralf Baechle:
"This week's round of MIPS fixes:
- Fix JZ4740 build
- Fix fallback to GFP_DMA
- FP seccomp in case of ENOSYS
- Fix bootmem panic
- A number of FP and CPS fixes
- Wire up new syscalls
- Make sure BPF assembler objects can properly be disassembled
- Fix BPF assembler code for MIPS I"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: scall: Always run the seccomp syscall filters
MIPS: Octeon: Fix kernel panic on startup from memory corruption
MIPS: Fix R2300 FP context switch handling
MIPS: Fix octeon FP context switch handling
MIPS: BPF: Fix load delay slots.
MIPS: BPF: Do all exports of symbols with FEXPORT().
MIPS: Fix the build on jz4740 after removing the custom gpio.h
MIPS: CPS: #ifdef on CONFIG_MIPS_MT_SMP rather than CONFIG_MIPS_MT
MIPS: CPS: Don't include MT code in non-MT kernels.
MIPS: CPS: Stop dangling delay slot from has_mt.
MIPS: dma-default: Fix 32-bit fall back to GFP_DMA
MIPS: Wire up userfaultfd and membarrier syscalls.
The MIPS syscall handler code used to return -ENOSYS on invalid
syscalls. Whilst this is expected, it caused problems for seccomp
filters because the said filters never had the change to run since
the code returned -ENOSYS before triggering them. This caused
problems on the chromium testsuite for filters looking for invalid
syscalls. This has now changed and the seccomp filters are always
run even if the syscall is invalid. We return -ENOSYS once we
return from the seccomp filters. Moreover, similar codepaths have
been merged in the process which simplifies somewhat the overall
syscall code.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11236/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
During development it was found that a number of builds would panic
during the kernel init process, more specifically in 'delayed_fput()'.
The panic showed the kernel trying to access a memory address of
'0xb7fdc00' while traversing the 'delayed_fput_list' structure.
Comparing this memory address to the value of the pointer used on
builds that did not panic confirmed that the pointer on crashing
builds must have been corrupted at some stage earlier in the init
process.
By traversing the list earlier and earlier in the code it was found
that 'plat_mem_setup()' was responsible for corrupting the list.
Specifically the line:
memory = cvmx_bootmem_phy_alloc(mem_alloc_size,
__pa_symbol(&__init_end), -1,
0x100000,
CVMX_BOOTMEM_FLAG_NO_LOCKING);
Which would eventually call:
cvmx_bootmem_phy_set_size(new_ent_addr,
cvmx_bootmem_phy_get_size
(ent_addr) -
(desired_min_addr -
ent_addr));
Where 'new_ent_addr'=0x4800000 (the address of 'delayed_fput_list')
and the second argument (size)=0xb7fdc00 (the address causing the
kernel panic). The job of this part of 'plat_mem_setup()' is to
allocate chunks of memory for the kernel to use. At the start of
each chunk of memory the size of the chunk is written, hence the
value 0xb7fdc00 is written onto memory at 0x4800000, therefore the
kernel panics when it goes back to access 'delayed_fput_list' later
on in the initialisation process.
On builds that were not crashing it was found that the compiler had
placed 'delayed_fput_list' at 0x4800008, meaning it wasn't corrupted
(but something else in memory was overwritten).
As can be seen in the first function call above the code begins to
allocate chunks of memory beginning from the symbol '__init_end'.
The MIPS linker script (vmlinux.lds.S) however defines the .bss
section to begin after '__init_end'. Therefore memory within the
.bss section is allocated to the kernel to use (System.map shows
'delayed_fput_list' and other kernel structures to be in .bss).
To stop the kernel panic (and the .bss section being corrupted)
memory should begin being allocated from the symbol '_end'.
Signed-off-by: Matt Bennett <matt.bennett@alliedtelesis.co.nz>
Acked-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: aleksey.makarov@auriga.com
Patchwork: https://patchwork.linux-mips.org/patch/11251/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 1a3d59579b9f ("MIPS: Tidy up FPU context switching") removed FP
context saving from the asm-written resume function in favour of reusing
existing code to perform the same task. However it only removed the FP
context saving code from the r4k_switch.S implementation of resume.
Remove it from the r2300_switch.S implementation too in order to prevent
attempting to save the FP context twice, which would likely lead to an
exception from the second save because the FPU had already been disabled
by the first save.
This patch has only been build tested, using rbtx49xx_defconfig.
Fixes: 1a3d59579b9f ("MIPS: Tidy up FPU context switching")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-kernel@vger.kernel.org
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/11167/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The entire bpf_jit_asm.S is written in noreorder mode because "we know
better" according to a comment. This also prevented the assembler from
throwing in the required NOPs for MIPS I processors which have no
load-use interlock, thus the load's consumer might end up using the
old value of the register from prior to the load.
Fixed by putting the assembler in reorder mode for just the affected
load instructions. This is not enough for gas to actually try to be
clever by looking at the next instruction and inserting a nop only
when needed but as the comment said "we know better", so getting gas
to unconditionally emit a NOP is just right in this case and prevents
adding further ifdefery.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
FEXPORT also marks the symbol as code using .type symbol, @function.
Without objdump -d will output only a hexdump for code following the
affected symbols.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Somehow the wrong version of the patch to remove the use of custom
gpio.h on mips has been merged. This patch add the missing fixes for a
build error on jz4740 because linux/gpio.h doesn't provide any machine
specfics definitions anymore.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11089/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The CONFIG_MIPS_MT symbol can be selected by CONFIG_MIPS_VPE_LOADER in
addition to CONFIG_MIPS_MT_SMP. We only want MT code in the CPS SMP boot
vector if we're using MT for SMP. Thus switch the config symbol we ifdef
against to CONFIG_MIPS_MT_SMP.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: <stable@vger.kernel.org> # 3.16+
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10867/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The MT-specific code in mips_cps_boot_vpes can safely be omitted from
kernels which don't support MT, with the default VPE==0 case being used
as it would be after the has_mt (Config3.MT) check failed at runtime.
Discarding the code entirely will save us a few bytes & allow cleaner
handling of MT ASE instructions by later patches.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: <stable@vger.kernel.org> # 3.16+
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10866/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The has_mt macro ended with a branch, leaving its callers with a delay
slot that would be executed if Config3.MT is not set. However it would
not be executed if Config3 (or earlier Config registers) don't exist
which makes it somewhat inconsistent at best. Fill the delay slot in the
macro & fix the mips_cps_boot_vpes caller appropriately.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: <stable@vger.kernel.org> # 3.16+
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10865/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If there is a DMA zone (usually 24bit = 16MB I believe), but no DMA32
zone, as is the case for some 32-bit kernels, then massage_gfp_flags()
will cause DMA memory allocated for devices with a 32..63-bit
coherent_dma_mask to fall back to using __GFP_DMA, even though there may
only be 32-bits of physical address available anyway.
Correct that case to compare against a mask the size of phys_addr_t
instead of always using a 64-bit mask.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Fixes: a2e715a86c6d ("MIPS: DMA: Fix computation of DMA flags from device's coherent_dma_mask.")
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 2.6.36+
Patchwork: https://patchwork.linux-mips.org/patch/9610/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS fixes from Ralf Baechle:
- Properly setup irq handling for ATH79 platforms
- Fix bootmem mapstart calculation for contiguous maps
- Handle little endian and older CPUs correct in BPF
- Fix console for Fulong 2E systems
- Handle FTLB correctly on R6 CPUs
- Fixes for CM, GIC and MAAR support code
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Initialise MAARs on secondary CPUs
MIPS: print MAAR configuration during boot
MIPS: mm: compile maar_init unconditionally
irqchip: mips-gic: Fix pending & mask reads for MIPS64 with 32b GIC.
irqchip: mips-gic: Convert CPU numbers to VP IDs.
MIPS: CM: Provide a function to map from CPU to VP ID.
MIPS: Fix FTLB detection for R6
MIPS: cpu-features: Add cpu_has_ftlb
MIPS: ATH79: Add irq chip ar7240-misc-intc
MIPS: ATH79: Set missing irq ack handler for ar7100-misc-intc irq chip
MIPS: BPF: Fix build on pre-R2 little endian CPUs
MIPS: BPF: Avoid unreachable code on little endian
MIPS: bootmem: Fix mapstart calculation for contiguous maps
MIPS: Fix console output for Fulong2e system
MAARs should be initialised on each CPU (or rather, core) in the system
in order to achieve consistent behaviour & performance. Previously they
have only been initialised on the boot CPU which leads to performance
problems if tasks are later scheduled on a secondary CPU, particularly
if those tasks make use of unaligned vector accesses where some CPUs
don't handle any cases in hardware for non-speculative memory regions.
Fix this by recording the MAAR configuration from the boot CPU and
applying it to secondary CPUs as part of their bringup.
Reported-by: Doug Gilmore <doug.gilmore@imgtec.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: David Hildenbrand <dahi@linux.vnet.ibm.com>
Cc: linux-kernel@vger.kernel.org
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Hemmo Nieminen <hemmo.nieminen@iki.fi>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11239/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Verifying that the MAAR configuration is as expected is useful when
debugging the performance of a system. Print out the memory regions
configured via MAAR along with their attributes.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: David Hildenbrand <dahi@linux.vnet.ibm.com>
Cc: linux-kernel@vger.kernel.org
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11238/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
maar_init was previously only compiled when CONFIG_NEED_MULTIPLE_NODES
was not set, which has been fine since it is only called from the
standard implementation of mem_init which has the same condition. In
preparation for calling it from the SMP startup code on secondary CPUs,
move maar_init outside of the #ifndef such that it is always compiled.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: David Hildenbrand <dahi@linux.vnet.ibm.com>
Cc: linux-kernel@vger.kernel.org
Cc: Ingo Molnar <mingo@kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/11237/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The VP ID of a given CPU may not match up with the CPU number used by
Linux. For example, if the width of the VP part of the VP ID is wider
than log2(number of VPs per core) and the system has multiple cores then
this will be the case. Alternatively, if a pre-r6 system implements the
MT ASE with multiple VPEs per core and Linux is built without support
for the MT ASE then the numbers won't match up either. Provide a
function to convert from CPU number to VP ID.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11211/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Resource management
- Revert pci_read_bridge_bases() unification (Bjorn Helgaas)
- Clear IORESOURCE_UNSET when clipping a bridge window (Bjorn Helgaas)
MSI
- Fix MSI IRQ domains for VFs on virtual buses (Alex Williamson)
Renesas R-Car host bridge driver
- Add R8A7794 support (Sergei Shtylyov)
Miscellaneous
- Fix devfn for VPD access through function 0 (Alex Williamson)
- Use function 0 VPD only for identical functions (Alex Williamson)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=f4c3
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.3-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These are fixes for things we merged for v4.3 (VPD, MSI, and bridge
window management), and a new Renesas R8A7794 SoC device ID.
Details:
Resource management:
- Revert pci_read_bridge_bases() unification (Bjorn Helgaas)
- Clear IORESOURCE_UNSET when clipping a bridge window (Bjorn
Helgaas)
MSI:
- Fix MSI IRQ domains for VFs on virtual buses (Alex Williamson)
Renesas R-Car host bridge driver:
- Add R8A7794 support (Sergei Shtylyov)
Miscellaneous:
- Fix devfn for VPD access through function 0 (Alex Williamson)
- Use function 0 VPD only for identical functions (Alex Williamson)"
* tag 'pci-v4.3-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: rcar: Add R8A7794 support
PCI: Use function 0 VPD for identical functions, regular VPD for others
PCI: Fix devfn for VPD access through function 0
PCI/MSI: Fix MSI IRQ domains for VFs on virtual buses
PCI: Clear IORESOURCE_UNSET when clipping a bridge window
PCI: Revert "PCI: Call pci_read_bridge_bases() from core instead of arch code"
and a few PPC bug fixes too.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJWBSn7AAoJEL/70l94x66Dxd4H/RT6kWWj9x4grEYUkcJUDyK2
AXm7XcKQm04auwAic8Otr+ts/Qix/50kWmBe/TU0QLgqb8rj5Dj3yGFK6Z1y6mAz
KvaxqMJd4tZGTqN0DDvC2ItEdzjfAdeJZo/FHXqPHVspG0G14T7STLna02LTBBEJ
tNzY9qor8nFhg2fT2szqKaudUNgTqkCTpo57o2BrHE96SHG+m0WdpQCV1F5hPVpg
Te0Pb7qX9xng5n3sQ7IV/t3QYbrza1ACwNQS9XJa0Yu6iEz7JdmVmzHQASK9ynn6
hUHhsNYGx4IsPjPtfJk2GroNaRDZL+VMzw07tfcOvPx8xkS9hS63pwzmSBqfLrM=
=Ywqn
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"AMD fixes for bugs introduced in the 4.2 merge window, and a few PPC
bug fixes too"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: disable halt_poll_ns as default for s390x
KVM: x86: fix off-by-one in reserved bits check
KVM: x86: use correct page table format to check nested page table reserved bits
KVM: svm: do not call kvm_set_cr0 from init_vmcb
KVM: x86: trap AMD MSRs for the TSeg base and mask
KVM: PPC: Book3S: Take the kvm->srcu lock in kvmppc_h_logical_ci_load/store()
KVM: PPC: Book3S HV: Pass the correct trap argument to kvmhv_commence_exit
KVM: PPC: Book3S HV: Fix handling of interrupted VCPUs
kvm: svm: reset mmu on VCPU reset
We observed some performance degradation on s390x with dynamic
halt polling. Until we can provide a proper fix, let's enable
halt_poll_ns as default only for supported architectures.
Architectures are now free to set their own halt_poll_ns
default value.
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
R6 removed the Config4.MMUExtDef field, with the low 16 bits only
allowed to contain FTLB fields, and commit e87569cd6c57 ("MIPS:
cpu-probe: Fix VTLB/FTLB configuration for R6") updated the probing of
this field to assume an FTLB is always present for R6.
However the FTLB may still be absent. The presence of those fields is
actually specified by the MMU type in the Config.MT field, so use that
(the new cpu_has_ftlb) to determine whether the FTLB is actually
present.
Fixes: e87569cd6c57 ("MIPS: cpu-probe: Fix VTLB/FTLB configuration for R6")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11160/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add cpu_has_ftlb, which specifies that an FTLB is present in addition to
the VTLB, probed based on whether Config.MT == 4 (rather than 1 for
standard JTLB).
This is necessary since MIPS release 6 removes Config4.MMUExtDef, so the
presence of the FTLB fields in Config4 must be determined from Config.MT
instead.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11159/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The ar7240 misc irq chip use ack handler
instead of ack_mask handler. All new ath79 chips use
the ar7240 misc irq chip
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Acked-by: Alban Bedel <albeu@free.fr>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: devicetree@vger.kernel.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11164/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The irq ack handler was forgotten while introducing OF support.
Only ar71xx and ar933x based devices require it.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Acked-by: Alban Bedel <albeu@free.fr>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: devicetree@vger.kernel.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11163/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The rotr, seh and wsbh instructions have been introduced with the R2
ISA. Thus the current BPF code fails to build on pre-R2 little endian
CPUs:
CC arch/mips/net/bpf_jit.o
AS arch/mips/net/bpf_jit_asm.o
/home/aurel32/linux-4.2/arch/mips/net/bpf_jit_asm.S: Assembler messages:
/home/aurel32/linux-4.2/arch/mips/net/bpf_jit_asm.S:67: Error: opcode not supported on this processor: mips32 (mips32) `wsbh $8,$19'
/home/aurel32/linux-4.2/arch/mips/net/bpf_jit_asm.S:68: Error: opcode not supported on this processor: mips32 (mips32) `rotr $19,$8,16'
/home/aurel32/linux-4.2/arch/mips/net/bpf_jit_asm.S:83: Error: opcode not supported on this processor: mips32 (mips32) `wsbh $8,$19'
/home/aurel32/linux-4.2/arch/mips/net/bpf_jit_asm.S:84: Error: opcode not supported on this processor: mips32 (mips32) `seh $19,$8'
/home/aurel32/linux-4.2/arch/mips/net/bpf_jit_asm.S:151: Error: opcode not supported on this processor: mips32 (mips32) `wsbh $8,$12'
/home/aurel32/linux-4.2/arch/mips/net/bpf_jit_asm.S:153: Error: opcode not supported on this processor: mips32 (mips32) `rotr $19,$8,16'
/home/aurel32/linux-4.2/arch/mips/net/bpf_jit_asm.S:164: Error: opcode not supported on this processor: mips32 (mips32) `wsbh $19,$12'
/home/aurel32/linux-4.2/scripts/Makefile.build:294: recipe for target 'arch/mips/net/bpf_jit_asm.o' failed
Fix that by providing equivalent code for these CPUs.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: stable@vger.kernel.org # v4.2+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11098/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On little endian, avoid generating the big endian version of the code
by using #else in addition to #ifdef #endif. Also fix one alignment
issue wrt delay slot.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: stable@vger.kernel.org # v4.2+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11097/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit a6335fa1 fixed the case with gap between initrd and next usable PFN zone,
but broken the case when initrd is combined with usable memory into one region
(in add_memory_region()). Restore the fixup initially brought in by f9a7febd.
---- error message ----
Unpacking initramfs...
Initramfs unpacking failed: junk in compressed archive
BUG: Bad page state in process swapper pfn:00261
page:81004c20 count:0 mapcount:-127 mapping: (null) index:0x2
flags: 0x0()
page dumped because: nonzero mapcount
CPU: 0 PID: 1 Comm: swapper Not tainted 4.2.0+ #1782
-----------------------
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Reported-by: Tony Wu <tung7970@gmail.com>
Tested-by: Tony Wu <tung7970@gmail.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Joe Perches <joe@perches.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: stable@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11086/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 3adeb2566b9b ("MIPS: Loongson: Improve LEFI firmware interface")
made the number of UARTs dynamic if LEFI_FIRMWARE_INTERFACE is configured.
Unfortunately, it did not initialize the number of UARTs if
LEFI_FIRMWARE_INTERFACE is not configured. As a result, the Fulong2e
system has no console.
Fixes: 3adeb2566b9b ("MIPS: Loongson: Improve LEFI firmware interface")
Acked-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11076/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJV+/ucAAoJEL/70l94x66DV8YH/1KDym/1GJ+/Br/YkHZnM53l
3Q0PwSLu9cNcIL9lUuDLwGTaVj+y8ud1Hjr/uzvKwivktmUYVZhkdtnZmnanvGOM
qKB9K3nFXCPx8uqy8Dn7fOwEKcg9FmDOTTkWy13HDnXO+V4crSVVt+rPw+6FUMld
NV5tYdw9Lu7y3XrveDebPWaPtyDL7OAagzmeK47eMffxG7X9Hf1H2aT7HueRi7x/
SkLIe3gmiOWmHVJDPE9TOmFYIj19gywDFysKes1gdVJLVUIXiELMT7SrvAYnToVB
zISIEj7Zx4SINPxpf2dUn8REm7NsmJY+PffLIl/Nv+ozGggFQGFH0SMZ08p0bxw=
=tfmn
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Mostly stable material, a lot of ARM fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (22 commits)
sched: access local runqueue directly in single_task_running
arm/arm64: KVM: Remove 'config KVM_ARM_MAX_VCPUS'
arm64: KVM: Remove all traces of the ThumbEE registers
arm: KVM: Disable virtual timer even if the guest is not using it
arm64: KVM: Disable virtual timer even if the guest is not using it
arm/arm64: KVM: vgic: Check for !irqchip_in_kernel() when mapping resources
KVM: s390: Replace incorrect atomic_or with atomic_andnot
arm: KVM: Fix incorrect device to IPA mapping
arm64: KVM: Fix user access for debug registers
KVM: vmx: fix VPID is 0000H in non-root operation
KVM: add halt_attempted_poll to VCPU stats
kvm: fix zero length mmio searching
kvm: fix double free for fast mmio eventfd
kvm: factor out core eventfd assign/deassign logic
kvm: don't try to register to KVM_FAST_MMIO_BUS for non mmio eventfd
KVM: make the declaration of functions within 80 characters
KVM: arm64: add workaround for Cortex-A57 erratum #852523
KVM: fix polling for guest halt continued even if disable it
arm/arm64: KVM: Fix PSCI affinity info return value for non valid cores
arm64: KVM: set {v,}TCR_EL2 RES1 bits
...
Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.
Remove the argument.
Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
This new statistic can help diagnosing VCPUs that, for any reason,
trigger bad behavior of halt_poll_ns autotuning.
For example, say halt_poll_ns = 480000, and wakeups are spaced exactly
like 479us, 481us, 479us, 481us. Then KVM always fails polling and wastes
10+20+40+80+160+320+480 = 1110 microseconds out of every
479+481+479+481+479+481+479 = 3359 microseconds. The VCPU then
is consuming about 30% more CPU than it would use without
polling. This would show as an abnormally high number of
attempted polling compared to the successful polls.
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com<
Reviewed-by: David Matlack <dmatlack@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Revert dff22d2054b5 ("PCI: Call pci_read_bridge_bases() from core instead
of arch code").
Reading PCI bridge windows is not arch-specific in itself, but there is PCI
core code that doesn't work correctly if we read them too early. For
example, Hannes found this case on an ARM Freescale i.mx6 board:
pci_bus 0000:00: root bus resource [mem 0x01000000-0x01efffff]
pci 0000:00:00.0: PCI bridge to [bus 01-ff]
pci 0000:00:00.0: BAR 8: no space for [mem size 0x01000000] (mem window)
pci 0000:01:00.0: BAR 2: failed to assign [mem size 0x00200000]
pci 0000:01:00.0: BAR 1: failed to assign [mem size 0x00004000]
pci 0000:01:00.0: BAR 0: failed to assign [mem size 0x00000100]
The 00:00.0 mem window needs to be at least 3MB: the 01:00.0 device needs
0x204100 of space, and mem windows are megabyte-aligned.
Bus sizing can increase a bridge window size, but never *decrease* it (see
d65245c3297a ("PCI: don't shrink bridge resources")). Prior to
dff22d2054b5, ARM didn't read bridge windows at all, so the "original size"
was zero, and we assigned a 3MB window.
After dff22d2054b5, we read the bridge windows before sizing the bus. The
firmware programmed a 16MB window (size 0x01000000) in 00:00.0, and since
we never decrease the size, we kept 16MB even though we only needed 3MB.
But 16MB doesn't fit in the host bridge aperture, so we failed to assign
space for the window and the downstream devices.
I think this is a defect in the PCI core: we shouldn't rely on the firmware
to assign sensible windows.
Ray reported a similar problem, also on ARM, with Broadcom iProc.
Issues like this are too hard to fix right now, so revert dff22d2054b5.
Reported-by: Hannes <oe5hpm@gmail.com>
Reported-by: Ray Jui <rjui@broadcom.com>
Link: http://lkml.kernel.org/r/CAAa04yFQEUJm7Jj1qMT57-LG7ZGtnhNDBe=PpSRa70Mj+XhW-A@mail.gmail.com
Link: http://lkml.kernel.org/r/55F75BB8.4070405@broadcom.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
