This patch fixes a bug in ath9k_hw_init_cal() where the wrong
calibration was being done for non-AR9285 chipsets.
Also add a few helpful comments.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces old 'hal_' prefixes with 'ath9k_'.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up the functions dealing with calibration,
using proper return values.
ath9k_hw_per_calibration(), ath9k_hw_calibrate now return bool values
instead of setting error values in the function arguments.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The various ANI timers have to be initialized properly when
starting the calibration timer.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ADC gain calibration has to be done for all non 2GHZ-HT20 channels.
Regression from "ath9k: use ieee80211_conf on ath9k_hw_iscal_supported()"
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The operating HT mode is stored in chanmode and
not channelFlags.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A full HW reset needs to be done on termination of a scan run.
Not setting SC_OP_FULL_RESET resulted in doing a
fast channel change.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver-specific region has to be freed in case
of a DMA mapping failure.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Radio enable/disable have to handle ASPM state properly.
This patch fixes it.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_getisr() doesn't appear to set anything in the status mask for
PCI FATAL or PERR interrupts (AR_INTR_SYNC_HOST1_FATAL/PERR), which
the open-source HAL seems to do. This means that the card isn't reset
after these interrupts.
This patch seems to fix a problem where the wireless drops out with an
"ath9k: received PCI FATAL interrupt" in dmesg after some time; the
hardware is an AR5416 in an ASUS WL-500W running 2.6.28.7 (OpenWRT) and
compat-wireless 2009-03-31.
Signed-off-by: Steven Luo <steven@steven676.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch ports commit c97a4ccc1f "b43: Fix beacon BH update" to
b43legacy. It fixes beacon updating in the bottomhalf. In case the device
is busy, we will defer to later in the IRQ handler.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Tested-by: David Ellingsworth <david@identd.dyndns.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch ports the beaconing fixes from commit a82d992261 "b43: Beaconing
fixes" to b43legacy. Basically it prevents the card from triggering the beacon
IRQ over and over again.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Tested-by: David Ellingsworth <david@identd.dyndns.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
That will make the various cases where the WARN_ON
can happen distinguishable.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The signal quality percentage is now calculated by mac80211 stack.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch takes care of outstanding TODOs:
/* TODO: some devices have 4 more free slots for rx keys */
Now the driver can utilize all available key slots instead of just 4.
Obviously, this helps most in AP/IBSS(/MESH) mode, when
we have to use more different keys.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rfkill system fails to issue a LED trigger event when the rfkill state
changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes unnecessary MMIO accesses in the interrupt hotpath.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/libertas/rx.c: In function ‘lbs_process_rxed_packet’:
drivers/net/wireless/libertas/rx.c:184: warning: format ‘%zd’ expects type ‘signed size_t’, but argument 4 has type ‘__le32’
drivers/net/wireless/libertas/rx.c:184: warning: format ‘%zd’ expects type ‘signed size_t’, but argument 5 has type ‘unsigned int’
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds interrupt statistics report to debugfs, this can help to
understand number of interrupts happened which including HW/SW error for
easier and better debugging.
in /sys/kernel/debug/ieee80211/phyN/iwlagn/data directory
use "cat interrupt" to view the current interrupt counter
use "echo 0 > interrupt" to clear interrupt counter
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix displaying of wrong channel information when user query
channel through debugfs
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For completeness, we should also make sure that the 3x3 MIMO rates are also checked when seeing if one rxon struct matches another.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to sync rxon_active with changes after we commit rxon_assoc,
without rxon_active will still have the old data that cause
iwl_send_rxon_assoc to fail with no change in rxon command.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug introduced by commit "iwlwifi: adding MIMO3 support
in rate scaling". We should not set the dual_stream_ant_msk (for 2x2 MIMO)
when using a 3x3 rate, this will cause a SYSASSERT in uCode.
Note: there is no triple_stream_ant_msk, because all three antennas are used.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adding MCS information in rate_scale_table, it help for
debugging rate scaling algorithm, easy to understand what is the current
rate scale table and matching modulation, plus the last mcs used for tx.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 can now use iwl_mac_reset_tsf from iwlwifi.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 can now use iwl_mac_get_tx_stats from iwlwifi.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 can now use iwl_mac_config_interface from iwlwifi.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add config_ap lib op to iwlwifi and iwl3945 in preparation
of future 3945 porting actions.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 can now use iwl_mac_config from iwlwifi
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 can now use iwl_mac_remove_interface from iwlwifi
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 can now use iwl_set_mode from iwlcore library.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add set_rxon_chain op to iwlwifi cfg ops in preparation of
future 3945 porting work.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl3945 can now use iwl_get_sta_id.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch unifies the add_station function for 3945 and iwlwifi drivers.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch replaces station function used in driver by station management ops
in 3945.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds declarations for station management ops to iwlwifi drivers.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Delay mode setting till uCode is ready.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 can use iwl_mac_beacon_update.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 can use iwl_bss_info_changed.
A new lib op is created for post_assoicate to distinguish between
3945 and iwlwifi's post_associate operations.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't currently support antenna or rate setting, so remove
that. Also update the link -- the current one is dead and the
wiki can be kept updated easier.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the normal WPA or RSN case keys are only configured after
associating, so we should do that in that order when resuming
as well. It shouldn't really matter since we do not send any
data at either point, but iwlwifi prefers it this way and it
does seem more natural.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
libertas: add support for Marvell SD8688 chip
Use RxPD->pkt_ptr to locate eth803 header in the packet
received since SD8688/v10 firmware allows a gap between
RxPD and eth803 header.
Set SDIO block size to 256 for CMD53.
The maximum block size for SD8688 WLAN function is set
to 512 in TPLFE_MAX_BLK_SIZE. But using 512 as block size
results upto 2K bytes data (4 blocks) being transferred
and causes buffer overflow in firmware.
Both changes above are backward compatible with earlier
firmware versions for SD8385/SD8686.
The SDIO_DEVICE_IDs for SD8688 chip are added in
include/linux/mmc/sdio_ids.h
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
p54spi_wakeup and p54spi_tx_frame used busy-waiting loop
to poll for 'ready' bits in SPI_ADRS_HOST_INTERRUPTS register.
With this change in place 'WR_READY timeout' messages do not
show anymore.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for the LEDs on the Jupiter netbook.
Reported-by: Martin Bammer <mrb74@gmx.at>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, the libertas main thread contends with the spi driver thread
in the TX path. To improve throughput, ensure that the driver thread
has higher scheduling priority than the libertas main thread. Do this
by making the libertas spi driver thread a low priority real time
thread.
We measured an average throughput improvement of 13%.
Signed-off-by: Anna Neal <anna@cozybit.com>
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the necessary code and fields to let drivers specify
their cipher capabilities and exports them to userspace. Also
update mac80211 to export the ciphers it has.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
