This patch adds initialization HSMMC device information.
And HSMMC platform data like card detect, data bus width
and capability is configured.
Signed-off-by: Hyuk Lee <hyuk1.lee@samsung.com>
Signed-off-by: Jeongbae Seo <jeongbae.seo@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support HSMMC for S5PV310 and S5PC210 and
setup for HSMMC host controller and also related GPIO.
At most 4 channel can be used at the same time.
A user can configure SDHCI data bus as 8bit or 4bit.
Signed-off-by: Hyuk Lee <hyuk1.lee@samsung.com>
Signed-off-by: Jeongbae Seo <jeongbae.seo@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch clean up the GPIO code and removes useless GPIO addresses.
It can be calculated with offset, the 'base' member of s3c_gpio_chip
is also initialized in the init function.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
When merged patches, missed IRQ_EINT_BIT() definition from commit ea31fd43
(ARM: S5PV210: Add Power Management Support). The IRQ_EINT_BIT() is used
in the Power Management operation (plat-samsung/pm.c).
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
When converting to use s3c_gpio_cfgpin_range() the function for the
IISv4 block appears to have been typoed as 4 (the keypad) rather than
5 as it should be.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes code setting special-function and no pull-up
to use the s3c_gpio_cfgrange_nopull() wrapper.
NOTE: This is for missed things from the previous patch.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes code setting special-function and no pull-up
to use the s3c_gpio_cfgrange_nopull() wrapper.
NOTE: This is for missed things from the previous patch.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes code setting special-function and no pull-up
to use the s3c_gpio_cfgrange_nopull() wrapper.
NOTE: This is for missed things from the previous patch.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change code setting special-function and no pull-up to use
the s3c_gpio_cfgrange_nopull() wrapper.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change code setting special-function and no pull-up to use
the s3c_gpio_cfgrange_nopull() wrapper.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change code setting special-function and no pull-up to use
the s3c_gpio_cfgrange_nopull() wrapper.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
A number of the SDHCI code configure a GPIO to a special function
and remove any pull-up, so add s3c_gpio_cfgrange_nopull() as a
wrapper to the s3c_gpio_cfgall_range() to make the code that
calls it fit on one line.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes the code setting range of GPIO pins' configuration and
pull state to use the recently introduced s3c_gpio_cfgpin_range().
NOTE: This is for missed things from the previous patch.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes the code setting range of GPIO pins' configuration and
pull state to use the recently introduced s3c_gpio_cfgpin_range().
NOTE: This is for missed things from the previous patch.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes the code setting range of GPIO pins' configuration and
pull state to use the recently introduced s3c_gpio_cfgpin_range().
NOTE: This is for missed things from the previous patch.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes the code setting range of GPIO pins' configuration and
pull state to use the recently introduced s3c_gpio_cfgpin_range().
NOTE: This is for missed things from the previous patch.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change the code setting a range of GPIO pins' configuration and
pull state to use the recently introduced s3c_gpio_cfgall_range().
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change the code setting a range of GPIO pins' configuration and
pull state to use the recently introduced s3c_gpio_cfgall_range().
Mop up a few missed s3c_gpio_cfgpin_range() changes.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change the code setting a range of GPIO pins' configuration and
pull state to use the recently introduced s3c_gpio_cfgall_range().
Mop up a few missed s3c_gpio_cfgpin_range() changes.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change the code setting a range of GPIO pins' configuration and
pull state to use the recently introduced s3c_gpio_cfgall_range().
Mop up a few missed s3c_gpio_cfgpin_range() changes.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change the code setting a range of GPIO pins' configuration and
pull state to use the recently introduced s3c_gpio_cfgall_range().
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change the code setting a range of GPIO pins' configuration and
pull state to use the recently introduced s3c_gpio_cfgall_range().
Mop up a few missed s3c_gpio_cfgpin_range() changes.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
[kgene.kim@samsung.com: Fix small comments]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add a function to configure a range of GPIOs function and
pull in one go, mainly for the SDHCI and framebuffer helpers
which tend to do this.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
[kgene.kim@samsung.com: Fix small comments]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes the code setting ranges of GPIO pins in mach-s5pv310 using
s3c_gpio_cfgpin() to use the recently introduced s3c_gpio_cfgpin_range().
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change the code setting ranges of GPIO pins using s3c_gpio_cfgpin() to
use the recently introduced s3c_gpio_cfgpin_range().
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
[kgene.kim@samsung.com: coding-style fixes]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change the code setting ranges of GPIO pins using s3c_gpio_cfgpin() to
use the recently introduced s3c_gpio_cfgpin_range().
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
[kgene.kim@samsung.com: Fixed wrong change]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes the code setting ranges of GPIO pins in mach-s5p64x0 using
s3c_gpio_cfgpin() to use the recently introduced s3c_gpio_cfgpin_range().
NOTE: This is for missed things from the previous patch.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change the code setting ranges of GPIO pins using s3c_gpio_cfgpin() to
use the recently introduced s3c_gpio_cfgpin_range().
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
[kgene.kim@samsung.com: modified to s5p64x0 from s5p6440]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change the code setting ranges of GPIO pins using s3c_gpio_cfgpin() to
use the recently introduced s3c_gpio_cfgpin_range().
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
[kgene.kim@samsung.com: fixed wrong change]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change the code setting ranges of GPIO pins using s3c_gpio_cfgpin() to
use the recently introduced s3c_gpio_cfgpin_range().
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
To aide in changing the gpio code, remove the use of pin-specific configs
and move to using the S3C_GPIO_SFN() versions.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add s3c_gpio_cfgpin_range() to configure a range of pins to the given
value. This is useful for a number of blocks where the pins are in order
and saves multiple calls to s3c_gpio_cfgpin().
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add required platform definitions for QT602240 touchscreen on I2C2 bus.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add required platform definitions for si470x radio device on Samsung
Goni board.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
[kgene.kim@samsung.com: minor title fixes]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add required platform definitions for S6E63M0 LCD controller on Samsung
Goni board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title fixes]
[kgene.kim@samsung.com: fix build error]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds suspend-to-ram support for S5PV210.
Note. This patch is confirmed on SMDKV210 and SMDKC110 board.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes build error by S3C2410 PM Suspend debug option
due to undefined address.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Samsung S5P SoCs have the same interrupt type defines for both
external interrupts and gpio interrupts. This patch removes all
duplicates from S5PC100 and S5PV210 specific includes as well as
gpio interrupt code and put a common defines to plat/irqs.h
NOTE: Do not use this for S5P6440 and S5P6450.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: add note for S5P64X0]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds a common callback for gpio_to_irq() for external and
gpio interrupts for Samsung SoCs.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
[kgene.kim@samsung.com: moved samsung_gpiolib_to_irq() for s3c24xx build]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves external interrupt definitions from mach/gpio.h
to mach/regs-gpio.h for consistency with S5PV210.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
S5PC100 SoC can use common S5P GPIO interrupt code. This patch
removes specific S5PC100 gpio interrupts code and adds required
defines and code to make use of common S5P code.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
S5PV210/S5PC110 can use common S5P GPIO interrupt code.
This patch adds required defines and code to make use of it.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title fixes]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds common code to enable support of GPIO interrupt on
S5P SoCs.
The total number of GPIO pins is quite large on S5P SoCs. Registering
irq support for all of them would be a resource waste. Because of that
the interrupt support for standard GPIO pins is registered dynamically
by the s5p_register_gpio_interrupt() function.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title fixes]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add the necessary definitions and mapping information to enable the
s3c-hsotg gadget to build.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add required platform definitions for MMC power regulators on Samsung
Goni board. GPIO pin GONI_EXT_FLASH_EN has been transferred from machine
startup code to fixed voltage regulator.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add required platform definitions for s3c-hsotg driver to enable usb
gadget support on Samsung Goni board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since commit 67a38950f0917aecfe1a3e46720d8bbb0020 there is no need
to set pixel clock for the s3c-fb driver's window information.
The correct pixel clock value can be automatically calculated from
the other screen parameters. This patch removes the redundant pixel clock
parameter.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change the default upper_margin and vsync_len to get rid of repeated last
line on the display.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
All the S5P series SoCs use the 'struct clksrc_clk' type to represent the
armclk. So the clk_arm clock instance available in the plat-s5p clock code
is not used in any of the S5P series SoCs.
This patch removes the unused clk_arm instance from plat-s5p clock code.
Reported-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
