Change to using a configurable RAM setup in startup code. This cleans up
the whole RAM base/sizing issue, and removes a lot of board specific code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the fixed RAM configurations for each board type from the
linker script. Replace with simple defines usng the flexible RAM
configuration options. This cleans out of lot of board specific
munging of addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reworked the way RAM regions are defined. Instead of coding all the
variations for each board type we now just configure RAM base and size
in the usual Kconfig setup. This much simplifies the code, and makes it
a lot more flexible when setting up new boards or board varients.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean out unused variable definitions from 68328 start up code.
Also use a more appropriate start address for the case of relocating
the kernel code to RAM (from ROM/flash).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
__ramvec has been removed from the linker script. The vector base
address is defined as a configurable option, use that. Remove its
use from the 68328/pilot startup code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
V4L/DVB (4227): Update this driver for recent header file movement.
V4L/DVB (4223): Add V4L2_CID_MPEG_STREAM_VBI_FMT control
V4L/DVB (4222): Always switch tuner mode when calling VIDIOC_S_FREQUENCY.
V4L/DVB (4221): Add HM12 YUV format define.
V4L/DVB (4219): Av7110: analog sound output of DVB-C rev 2.3
V4L/DVB (4217): Fix a misplaced closing bracket/else, which caused swzigzag not to be called
V4L/DVB (4215): Make VIDEO_CX88_BLACKBIRD a separate build option
V4L/DVB (4214): Make VIDEO_CX2341X a selectable build option
V4L/DVB (4213): Cx88: cleanups
V4L/DVB (4211): Fix an Oops for all fe that have get_frontend_algo == NULL
Applies to git & 2.6.17-rc6 after CONFIG_DEBUG_STACKOVERFLOW patch
uses same stack-zeroing mechanism as on i386 to discover maximum stack
excursions.
Signed-off-by: Eric Sandeen <sandeen@sgi.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Take two, now without spurious whitespace :( Applies to git & 2.6.17-rc6
CONFIG_DEBUG_STACKOVERFLOW existed for x86_64 in 2.4, but seems to have gone AWOL in 2.6.
I've pretty much just copied this over from the 2.4 code, with
appropriate tweaks for the 2.6 kernel, plus a bugfix. I'd personally
rather see it printed out the way other arches do it, i.e.
bytes-remaining-until-overflow, rather than having to do the subtraction
yourself. Also, only 128 bytes remaining seems awfully late to issue a
warning. But I'll start here :)
Signed-off-by: Eric Sandeen <sandeen@sgi.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CC drivers/pci/msi-apic.o
In file included from include/asm/msi.h:11,
from drivers/pci/msi.h:71,
from drivers/pci/msi-apic.c:8:
include/asm/smp.h:103: error: syntax error before '->' token
akpm: nasty. It appears to be
static inline unsigned int cpu_mask_to_apicid(cpumask_t cpumask)
conflicting with include/asm-x86_64/mach_apic.h's
#define cpu_mask_to_apicid (genapic->cpu_mask_to_apicid)
And I don't know which patch in rc4-mm1 triggered this.
Fixing this in the .c file seems wrong.
Including asm/smp.h instead of linux/smp.h seems wrong too. Need that
.config.
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Intel now has support for Architectural Performance Monitoring Counters
( Refer to IA-32 Intel Architecture Software Developer's Manual
http://www.intel.com/design/pentium4/manuals/253669.htm ). This
feature is present starting from Intel Core Duo and Intel Core Solo processors.
What this means is, the performance monitoring counters and some performance
monitoring events are now defined in an architectural way (using cpuid).
And there will be no need to check for family/model etc for these architectural
events.
Below is the patch to use this performance counters in nmi watchdog driver.
Patch handles both i386 and x86-64 kernels.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On some i386/x86_64 systems, sending an NMI IPI as a broadcast will
reset the system. This seems to be a BIOS bug which affects machines
where one or more cpus are not under OS control. It occurs on HT
systems with a version of the OS that is not compiled without HT
support. It also occurs when a system is booted with max_cpus=n where
2 <= n < cpus known to the BIOS. The fix is to always send NMI IPI as
a mask instead of as a broadcast.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Appended patch fixes the "APIC error on CPUX: 00(40)" observed during bootup.
From SDM Vol-3A "Valid Interrupt Vectors" section:
"When an illegal vector value (0-15) is written to an LVT entry
and the delivery mode is Fixed, the APIC may signal an illegal
vector error, with out regard to whether the mask bit is set
or whether an interrupt is actually seen on input."
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allow stack growth so the 'enter' instruction works. Also
fixes problem in compat_sys_kexec_load() which could allocate
more than 128 bytes using compat_alloc_user_space().
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Use tail call from clear_user to __clear_user to save some code size
- Use standard memcpy for forward memmove
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Only exports for assembler files are left in x8664_ksyms.c
Originally inspired by a patch from Al Viro
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
x86_64 and i386 behave inconsistently when sending an IPI on vector 2
(NMI_VECTOR). Make both behave the same, so IPI 2 is sent as NMI.
The crash code was abusing send_IPI_allbutself() by passing a code
instead of a vector, it only worked because crash knew about the
internal code of send_IPI_allbutself(). Change crash to use NMI_VECTOR
instead, and remove the comment about how crash was abusing the function.
This patch is a pre-requisite for fixing the problem where sending an
IPI as NMI would reboot some Dell Xeon systems. I cannot fix that
problem while crash continus to abuse send_IPI_allbutself().
It also removes the inconsistency between i386 and x86_64 for
NMI_VECTOR. That will simplify all the RAS code that needs to bring
all the cpus to a clean stop, even when one or more cpus are spinning
disabled.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It turned out that the following change is needed when the speaker is
compiled as a module.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes the no longer used sys32_ni_syscall()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently CONFIG_REORDER uses -ffunction-sections for all code;
however, creating a separate section for each function is not useful
for modules and just adds bloat. Moving this option from CFLAGS to
CFLAGS_KERNEL shrinks module object files (e.g., the module tree for a
kernel built with most drivers as modules shrinked from 54M to 46M),
and decreases the number of sysfs files in /sys/module/*/sections/
directories.
Signed-off-by: Sergey Vlasov <vsu@altlinux.ru>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This one is adding a cpu_relax() that already existed in the i386 version.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Defaulting to a value not evenly divisible by four makes little sense,
as four values are displayed per line (and hence the rest of the line
would otherwise be wasted).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With (significantly) more than 10 CPUs online, the column headings
drifted off the positions of the column contents with growing CPU
numbers.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When a process changes CPUs while doing the non atomic cpu_local_*
operations it might operate on the local_t of a different CPUs.
Fix that by disabling preemption.
Pointed out by Christopher Lameter
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The APIC ID returned by hard_smp_processor_id can be beyond
NR_CPUS and then overflow the x86_cpu_to_apic[] array.
Add a check for overflow. If it happens then the slow loop below
will catch.
Bug pointed out by Doug Thompson
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Getting phys_proc_id and cpu_core_id information to be printed at boot
time for AMD processors. Also matching the Node related boot time
information that gets printed for Intel and AMD processors for NUMA
configurations.
Signed-off-by: Rohit Seth <rohitseth@google.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
During some profiling I noticed that default_idle causes a lot of
memory traffic. I think that is caused by the atomic operations
to clear/set the polling flag in thread_info. There is actually
no reason to make this atomic - only the idle thread does it
to itself, other CPUs only read it. So I moved it into ti->status.
Converted i386/x86-64/ia64 for now because that was the easiest
way to fix ACPI which also manipulates these flags in its idle
function.
Cc: Nick Piggin <npiggin@novell.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
No red zone possible/needed on the alternative stack.
It caused confusion.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- fix an off-by-one error in phys_pmd_init()
- prevent phys_pmd_init() from removing mappings established earlier
- fix the direct mapping early printk to in fact show the end of the range
- remove an apparently orphan comment
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean up mce_amd.c for readability and remove code no
longer needed.
Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for mce threshold registers found in future
AMD family 0x10 processors. Backwards compatible with
family 0xF hardware.
AK: fixed build on !SMP
Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for extended APIC LVT found in future AMD processors.
Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Architecture specific configs like this have no business at all
in init/Kconfig. This prevents it from being set on x86-64
Pointed out by H.Peter Anvin
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
After writing the CFG register, the first value written to the T0_CMP
register is the value at which next interrupt should be triggered, every
value after that sets the period of the interrupt. For that reason, the code
needs to write the value twice - to set both the phase and period.
[AK: I had already figured it out by myself, but it's still useful
to have a comment for this.]
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch makes use of the newly added conversion constants
in time.h to x86-64 time.c. The code gets significantly easier
to understand.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove #ifdefed code to manually enable HPET on AMD8111, where the
BIOS doesn't have ACPI HPET tables and doesn't enable it for us.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds the X86_FEATURE_RDTSCP #define, so that kernel code can
check for the feature easily and also fixes the location of the "rdtscp"
string in the cpuinfo tables.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rename oem_force_hpet_timer to apic_is_clustered_box, to give the
function a better fitting name - it really isn't at all about HPET.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In timekeeping code, one often does need to use conversion constants. Naming
these leads to code that's easier to understand, showing the reader between
which units the conversion is made.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Most of the fields of cpuinfo are defined in cpuinfo_x86 structure.
This patch moves the phys_proc_id and cpu_core_id for each processor to
cpuinfo_x86 structure as well.
Signed-off-by: Rohit Seth <rohitseth@google.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch hooks Calgary into the build, the x86-64 IOMMU
initialization paths, and introduces the Calgary specific bits. The
implementation draws inspiration from both PPC (which has support for
the same chip but requires firmware support which we don't have on
x86-64) and gart. Calgary is different from gart in that it support a
translation table per PHB, as opposed to the single gart aperture.
Changes from previous version:
* Addition of boot-time disablement for bus-level translation/isolation
(e.g, enable userspace DMA for things like X)
* Usage of newer IOMMU abstraction functions
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch creates a new interface for IOMMUs by adding a centralized
location for IOMMU allocation (for translation tables/apertures) and
IOMMU initialization. In creating these, code was moved around for
abstraction, uniformity, and consiceness.
Take note of the move of the iommu_setup bootarg parsing code to
__setup. This is enabled by moving back the location of the aperture
allocation/detection to mem init (which while ugly, was already the
location of the swiotlb_init).
While a slight departure from the previous patch, I belive this provides
the true intention of the previous versions of the patch which changed
this code. It also makes the addition of the upcoming calgary code much
cleaner than previous patches.
[AK: Removed one broken change. iommu_setup still has to be called
early]
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Based on Andi Kleen's comments on the original Calgary patch, move
valid_dma_direction into the calling functions.
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
swiotlb relies on the gart specific iommu_aperture variable to know if
we discovered a hardware IOMMU before swiotlb initialization. Introduce
iommu_detected to do the same thing, but in a HW IOMMU neutral manner,
in preparation for adding the Calgary HW IOMMU.
Signed-Off-By: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-Off-By: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
