Commit Graph

261108 Commits

Author SHA1 Message Date
Yaniv Rosner
157fa283a7 bnx2x: Fix BCM578xx-B0 MDIO access
Fix MDIO access to Warpcore on new chip version of 578xx.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-03 03:22:17 -07:00
Yaniv Rosner
de6f3377d2 bnx2x: Fix remote fault handling
Fix couple of issues of remote fault detection and handling:
Link may go down due to remote fault indications during link establishment.
Possible link down after primary function migration.
Remote fault was not detected on 578xx.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-03 03:22:17 -07:00
Yaniv Rosner
b507766205 bnx2x: Fix chip hanging due to TX pipe stall.
Fix a problem in which the 578xx chip hangs after running traffic, and then pulling the network cable.
This occurs since TX pipe is stalled due to missing XON indication towards the NIG.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-03 03:22:17 -07:00
Yaniv Rosner
9d5b36be64 bnx2x: Fix missing pause on for 578xx
When link speed is 1G and below, pause weren't sent due to missing pause setting in the UMAC.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-03 03:22:17 -07:00
françois romieu
c28aa38567 r8169 : MAC address change fix for the 8168e-vl.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=39252

Hayes suggested that the usual MAC{0, 4} register writes be completed
with writes to extended GigaMAC registers :
- 0xe0 .. 0xe5
- 0xf2 .. 0xf7

Registers 0xf0 and 0xf1 should be set to 0.

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-02 17:08:58 -07:00
Vladislav Zolotarov
87b7ba3d24 bnx2x: Prevent restarting Tx during bnx2x_nic_unload
Tx queues were stopped before  bp->state was changed to a value different 
from BNX2X_STATE_OPEN, which allowed the bnx2x_tx_int() called from the 
NAPI context to re-enable it. This then allowed the netdev->ndo_start_xmit() 
to be called in the middle of the function reset and rings freeing. 

This patch changes bp->state to a value different 
from BNX2X_STATE_OPEN BEFORE disabling the Tx queues in order to restore the
broken protection against the above race in the bnx2x_tx_int().

Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-02 01:35:43 -07:00
Eric Dumazet
22019b1782 net: add kerneldoc to skb_copy_bits()
Since skb_copy_bits() is called from assembly, add a fat comment to make
clear we should think twice before changing its prototype.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-01 18:03:06 -07:00
Jesper Juhl
8fb4e13991 Documentation/bonding.txt: Update to 3.x version numbers
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-01 17:59:44 -07:00
Paul Moore
82c21bfab4 doc: Update the email address for Paul Moore in various source files
My @hp.com will no longer be valid starting August 5, 2011 so an update is
necessary.  My new email address is employer independent so we don't have
to worry about doing this again any time soon.

Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-01 17:58:33 -07:00
Paul Moore
87a0874cf1 doc: Update the MAINTAINERS info for Paul Moore
My @hp.com will no longer be valid starting August 5, 2011 so an update is
necessary.  My new email address is employer independent so we don't have
to worry about doing this again any time soon.

Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-01 17:58:33 -07:00
Chas Williams
a08af810cd atm: br2864: sent packets truncated in VC routed mode
Reported-by: Pascal Hambourg <pascal@plouf.fr.eu.org>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-01 17:56:14 -07:00
Eric Dumazet
e1738bd9ce sch_sfq: fix sfq_enqueue()
commit 8efa885406 (sch_sfq: avoid giving spurious NET_XMIT_CN signals)
forgot to call qdisc_tree_decrease_qlen() to signal upper levels that a
packet (from another flow) was dropped, leading to various problems.

With help from Michal Soltys and Michal Pokrywka, who did a bisection.

Bugzilla ref: https://bugzilla.kernel.org/show_bug.cgi?id=39372
Debian ref: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=631945

Reported-by: Lucas Bocchi <lucas.bocchi@gmail.com>
Reported-and-bisected-by: Michal Pokrywka <wolfmoon@o2.pl>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Michal Soltys <soltys@ziu.info>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-01 02:27:21 -07:00
Julia Lawall
956837f7c9 drivers/net/niu.c: adjust array index
Convert array index from the loop bound to the loop index.

A simplified version of the semantic patch that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression e1,e2,ar;
@@

for(e1 = 0; e1 < e2; e1++) { <...
  ar[
- e2
+ e1
  ]
  ...> }
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-01 02:27:21 -07:00
Julia Lawall
a1889c0d20 net: adjust array index
Convert array index from the loop bound to the loop index.

A simplified version of the semantic patch that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression e1,e2,ar;
@@

for(e1 = 0; e1 < e2; e1++) { <...
  ar[
- e2
+ e1
  ]
  ...> }
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-01 02:27:21 -07:00
David S. Miller
2a1690d8cd MAINTAINERS: Remove Pekka Savola from ipv6.
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-01 02:23:15 -07:00
David S. Miller
384b90abeb Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/ipvs-2.6 2011-07-28 18:38:53 -07:00
Oleg Nesterov
9e8f90dfe5 proc_fork_connector: a lockless ->real_parent usage is not safe
proc_fork_connector() uses ->real_parent lockless.  This is not safe if
copy_process() was called with CLONE_THREAD or CLONE_PARENT, in this case
the parent != current can go away at any moment.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-28 18:26:32 -07:00
Randy Dunlap
177c27bf05 net: fix new sunrpc kernel-doc warning
Fix new kernel-doc warning in sunrpc:

Warning(net/sunrpc/xprt.c:196): No description found for parameter 'xprt'

Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-28 18:20:21 -07:00
Lennart Sorensen
93a3aa2593 r8169: Add support for D-Link 530T rev C1 (Kernel Bug 38862)
The D-Link DGE-530T rev C1 is a re-badged Realtek 8169 named DLG10028C,
unlike the previous revisions which were skge based.  It is probably
the same as the discontinued DGE-528T (0x4300) other than the PCI ID.

The PCI ID is 0x1186:0x4302.

Adding it to r8169.c where 0x1186:0x4300 is already found makes the card
be detected and work.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=38862

Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-28 18:15:28 -07:00
Joe Perches
c173bfac24 MAINTAINERS: orphan FrameRelay DLCI
Mike McLagan hasn't contributed in many years and his email bounces.

Signed-off-by: Joe Perches <joe@perches.com>
Cc: David Miller <davem@davemloft.net>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-28 18:13:05 -07:00
Klement Fish
fe66101f14 sis190: Rx filter init is needed for MAC address change.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=34552

Signed-off-by: Klement Fish <klement2@azet.sk>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-28 18:11:51 -07:00
Tushar Gohad
4203223a1a xfrm: Fix key lengths for rfc3686(ctr(aes))
Fix the min and max bit lengths for AES-CTR (RFC3686) keys.
The number of bits in key spec is the key length (128/256)
plus 32 bits of nonce.

This change takes care of the "Invalid key length" errors
reported by setkey when specifying 288 bit keys for aes-ctr.

Signed-off-by: Tushar Gohad <tgohad@mvista.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-28 18:10:48 -07:00
Linus Torvalds
55f9c40ff6 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  n2_crypto: Attach on Niagara-T3.
  n2rng: Attach on Niagara-T3.
  sparc: Detect and handle UltraSPARC-T3 cpu types.
  sparc: Don't do expensive hypervisor PCR write unless necessary.
  sparc: Add T3 sun4v cpu type and hypervisor group defines.
  sparc: Don't leave sparc_pmu_type NULL on sun4v.
2011-07-28 05:59:19 -07:00
Linus Torvalds
d5eab9152a Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (32 commits)
  tg3: Remove 5719 jumbo frames and TSO blocks
  tg3: Break larger frags into 4k chunks for 5719
  tg3: Add tx BD budgeting code
  tg3: Consolidate code that calls tg3_tx_set_bd()
  tg3: Add partial fragment unmapping code
  tg3: Generalize tg3_skb_error_unmap()
  tg3: Remove short DMA check for 1st fragment
  tg3: Simplify tx bd assignments
  tg3: Reintroduce tg3_tx_ring_info
  ASIX: Use only 11 bits of header for data size
  ASIX: Simplify condition in rx_fixup()
  Fix cdc-phonet build
  bonding: reduce noise during init
  bonding: fix string comparison errors
  net: Audit drivers to identify those needing IFF_TX_SKB_SHARING cleared
  net: add IFF_SKB_TX_SHARED flag to priv_flags
  net: sock_sendmsg_nosec() is static
  forcedeth: fix vlans
  gianfar: fix bug caused by 87c288c6e9
  gro: Only reset frag0 when skb can be pulled
  ...
2011-07-28 05:58:19 -07:00
Linus Torvalds
6140333d36 Merge branch 'for-linus' of git://neil.brown.name/md
* 'for-linus' of git://neil.brown.name/md: (75 commits)
  md/raid10: handle further errors during fix_read_error better.
  md/raid10: Handle read errors during recovery better.
  md/raid10: simplify read error handling during recovery.
  md/raid10: record bad blocks due to write errors during resync/recovery.
  md/raid10:  attempt to fix read errors during resync/check
  md/raid10:  Handle write errors by updating badblock log.
  md/raid10: clear bad-block record when write succeeds.
  md/raid10: avoid writing to known bad blocks on known bad drives.
  md/raid10 record bad blocks as needed during recovery.
  md/raid10: avoid reading known bad blocks during resync/recovery.
  md/raid10 - avoid reading from known bad blocks - part 3
  md/raid10: avoid reading from known bad blocks - part 2
  md/raid10: avoid reading from known bad blocks - part 1
  md/raid10: Split handle_read_error out from raid10d.
  md/raid10: simplify/reindent some loops.
  md/raid5: Clear bad blocks on successful write.
  md/raid5.  Don't write to known bad block on doubtful devices.
  md/raid5: write errors should be recorded as bad blocks if possible.
  md/raid5: use bad-block log to improve handling of uncorrectable read errors.
  md/raid5: avoid reading from known bad blocks.
  ...
2011-07-28 05:50:27 -07:00
Linus Torvalds
6f56c21866 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  sound: oss: rename local change_bits to avoid powerpc bitsops.h definition
  ALSA: hda - Fix duplicated DAC assignments for Realtek
  ALSA: asihpi - off by one in asihpi_hpi_ioctl()
  ALSA: hda - Fix Oops with Realtek quirks with NULL adc_nids
  ALSA: asihpi - bug fix pa use before init.
  ALSA: hda - Add support for vref-out based mute LED control on IDT codecs
2011-07-28 05:49:31 -07:00
David S. Miller
eb7caf3595 n2_crypto: Attach on Niagara-T3.
A small modification was necessary since in the machine description
for 'n2cp' and 'ncp' nodes, there no longer is an 'intr' property.

That's OK because this property was always nothing more than an
array of integers '1' ... 'nr_inos + 1' so we can just compute it
in-place.

Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-28 01:30:07 -07:00
David S. Miller
24f1466961 n2rng: Attach on Niagara-T3.
And stop referring to Victoria Falls, as the attribute we're
talking about is whether the rng is multi-unit capable which
applies to several chip variants now.

Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-28 01:26:30 -07:00
Matt Carlson
a051294423 tg3: Remove 5719 jumbo frames and TSO blocks
The A0 revision of this chip is the only device that requires these
features to be disabled.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-27 22:39:32 -07:00
Matt Carlson
e31aa98706 tg3: Break larger frags into 4k chunks for 5719
The 5719 has bug where RDMAs larger than 4k can cause problems.  This
patch works around the problem by dividing larger DMA requests into
something the hardware can handle.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-27 22:39:32 -07:00
Matt Carlson
84b67b27e9 tg3: Add tx BD budgeting code
As the driver breaks large skb fragments into smaller submissions to the
hardware, there is a new danger that BDs might get exhausted before all
fragments have been mapped.  This patch adds code to make sure tx BDs
aren't oversubscribed and flag the condition if it happens.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-27 22:39:32 -07:00
Matt Carlson
d1a3b7377d tg3: Consolidate code that calls tg3_tx_set_bd()
This patch consolidates all code that populates tx BDs into a single
routine.  Setting tx BDs needs to be more carefully controlled to see if
workarounds need to be applied.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-27 22:39:31 -07:00
Matt Carlson
e01ee14d49 tg3: Add partial fragment unmapping code
The following patches are going to break skb fragments into smaller
sizes.  This patch attempts to make the change easier to digest by only
addressing the skb teardown portion.

The patch modifies the driver to skip over any BDs that have a flag set
that indicates the BD isn't the beginning of an skb fragment.  Such BDs
were a result of segmentation and do not need a pci_unmap_page() call.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-27 22:39:31 -07:00
Matt Carlson
0d681b27b0 tg3: Generalize tg3_skb_error_unmap()
In the following patches, unmapping skb fragments will get just as
complicated as mapping them.  This patch generalizes
tg3_skb_error_unmap() and makes it the one-stop-shop for skb unmapping.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-27 22:39:31 -07:00
Matt Carlson
13350ea78b tg3: Remove short DMA check for 1st fragment
The first fragment of an skb should always be greater than 8 bytes.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-27 22:39:31 -07:00
Matt Carlson
92cd3a17ce tg3: Simplify tx bd assignments
In the following patches, the process the driver will use to assign skb
fragments to transmit BDs will get more complicated.  To prepare for
that new code, this patch seeks to simplify how transmit BDs are
populated.  It does this by separating the code that assigns the BD
members from the logic that controls how the fields are set.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-27 22:39:31 -07:00
Matt Carlson
df8944cf5c tg3: Reintroduce tg3_tx_ring_info
The following patches will require the use of an additional flag in the
ring_info structure.  The use of this flag is tx path specific, so this
patch defines a specialized ring_info structure.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-27 22:39:31 -07:00
Marek Vasut
bca0beb936 ASIX: Use only 11 bits of header for data size
The AX88772B uses only 11 bits of the header for the actual size. The other bits
are used for something else. This causes dmesg full of messages:

	asix_rx_fixup() Bad Header Length

This patch trims the check to only 11 bits. I believe on older chips, the
remaining 5 top bits are unused.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-27 22:39:31 -07:00
Marek Vasut
bc466e678d ASIX: Simplify condition in rx_fixup()
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-27 22:39:31 -07:00
Chris Clayton
a0295a3b67 Fix cdc-phonet build
Try to send to correct address this time!

----------  Forwarded Message  ----------

Subject: [PATCH] Fix cdc-phonet build
Date: Saturday 23 Jul 2011
From: Chris Clayton <chris2553@googlemail.com>
To: linux-net@vger.kernel.org

cdc-phonet does not presently build on linux-3.0 because there is no entry for it in
drivers/net/Makefile. This patch adds that entry.

Signed-off-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-27 22:39:31 -07:00
Andy Gospodarek
b2730f4f84 bonding: reduce noise during init
On Tue, Jul 26, 2011 at 05:40:27PM -0700, Joe Perches wrote:
> On Tue, 2011-07-26 at 17:37 -0700, Jay Vosburgh wrote:
> > Joe Perches <joe@perches.com> wrote:
> > >I'd prefer you don't separate the format string
> > >into multiple pieces.
> > Why not?  To me, it looks easier to read split into sections
> > that don't wrap lines.
>
> Harder to grep for a dmesg and the
> defect rate of these split formats is
> typically higher than single strings
> because of bad spacing between string
> segments.
>

I noticed that you took some time back in late 2009 to 'consolidate' the
split format-strings present in the bonding driver at the time and I've
decided I'm fine to leave them the way they are.  The main point of my
patch was to change the output and I would like to get that included.
Here is my updated patch...

Subject: [PATCH net-next-2.6 v2] bonding: reduce noise during init

Many are using sysfs to configure bonding rather than module options, so
there is no need for bonding to throw this warning in normal cases.

Keep the message around when debugging is enabled as it might be useful
for someone desperate enough to enable debugging, but eliminate it
otherwise.

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-27 22:39:30 -07:00
Andy Gospodarek
f4bb2e9c4f bonding: fix string comparison errors
When a bond contains a device where one name is the subset of another
(eth1 and eth10, for example), one cannot properly set the primary
device or the currently active device.

This was reported and based on work by Takuma Umeya.  I also verified
the problem and tested that this fix resolves it.

V2: A few did not like the the current code or my changes, so I
refactored bonding_store_primary and bonding_store_active_slave to be a
bit cleaner, dropped the use of strnicmp since we did not really need
the comparison to be case insensitive, and formatted the input string
from sysfs so a comparison to IFNAMSIZ could be used.

I also discovered an error in bonding_store_active_slave that would
modify bond->primary_slave rather than bond->curr_active_slave before
forcing the bonding driver to choose a new active slave.

V3: Actually sending the proper patch....

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Reported-by: Takuma Umeya <tumeya@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-27 22:39:30 -07:00
Neil Horman
550fd08c2c net: Audit drivers to identify those needing IFF_TX_SKB_SHARING cleared
After the last patch, We are left in a state in which only drivers calling
ether_setup have IFF_TX_SKB_SHARING set (we assume that drivers touching real
hardware call ether_setup for their net_devices and don't hold any state in
their skbs.  There are a handful of drivers that violate this assumption of
course, and need to be fixed up.  This patch identifies those drivers, and marks
them as not being able to support the safe transmission of skbs by clearning the
IFF_TX_SKB_SHARING flag in priv_flags

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Karsten Keil <isdn@linux-pingi.de>
CC: "David S. Miller" <davem@davemloft.net>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Patrick McHardy <kaber@trash.net>
CC: Krzysztof Halasa <khc@pm.waw.pl>
CC: "John W. Linville" <linville@tuxdriver.com>
CC: Greg Kroah-Hartman <gregkh@suse.de>
CC: Marcel Holtmann <marcel@holtmann.org>
CC: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-27 22:39:30 -07:00
Neil Horman
d887331506 net: add IFF_SKB_TX_SHARED flag to priv_flags
Pktgen attempts to transmit shared skbs to net devices, which can't be used by
some drivers as they keep state information in skbs.  This patch adds a flag
marking drivers as being able to handle shared skbs in their tx path.  Drivers
are defaulted to being unable to do so, but calling ether_setup enables this
flag, as 90% of the drivers calling ether_setup touch real hardware and can
handle shared skbs.  A subsequent patch will audit drivers to ensure that the
flag is set properly

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Jiri Pirko <jpirko@redhat.com>
CC: Robert Olsson <robert.olsson@its.uu.se>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Alexey Dobriyan <adobriyan@gmail.com>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-27 22:39:30 -07:00
Eric Dumazet
894dc24ce7 net: sock_sendmsg_nosec() is static
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Anton Blanchard <anton@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-27 22:39:30 -07:00
Jiri Pirko
0891b0e089 forcedeth: fix vlans
For some reason, when rxaccel is disabled, NV_RX3_VLAN_TAG_PRESENT is
still set and some pseudorandom vids appear. So check for
NETIF_F_HW_VLAN_RX as well. Also set correctly hw_features and set vlan
mode on probe.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-27 22:39:30 -07:00
Sebastian Pöhn
b852b72087 gianfar: fix bug caused by 87c288c6e9
commit 87c288c6e9 "gianfar: do vlan cleanup" has two issues:
# permutation of rx and tx flags
# enabling vlan tag insertion by default (this leads to unusable connections on some configurations)

If VLAN insertion is requested (via ethtool) it will be set at an other point ...

Signed-off-by: Sebastian Poehn <sebastian.poehn@belden.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-27 22:39:30 -07:00
David S. Miller
b49179c071 Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 2011-07-27 22:18:47 -07:00
David S. Miller
4ba991d3eb sparc: Detect and handle UltraSPARC-T3 cpu types.
The cpu compatible string we look for is "SPARC-T3".

As far as memset/memcpy optimizations go, we treat this chip the same
as Niagara-T2/T2+.  Use cache initializing stores for memset, and use
perfetch, FPU block loads, cache initializing stores, and block stores
for copies.

We use the Niagara-T2 perf support, since T3 is a close relative in
this regard.  Later we'll add support for the new events T3 can
report, plus enable T3's new "sample" mode.

For now I haven't added any new ELF hwcap flags.  We probably need
to add a couple, for example:

T2 and T3 both support the population count instruction in hardware.

T3 supports VIS3 instructions, including support (finally) for
partitioned shift.  One can also now move directly between float
and integer registers.

T3 supports instructions meant to help with Galois Field and other HPC
calculations, such as XOR multiply.  Also there are "OP and negate"
instructions, for example "fnmul" which is multiply-and-negate.

T3 recognizes the transactional memory opcodes, however since
transactional memory isn't supported: 1) 'commit' behaves as a NOP and
2) 'chkpt' always branches 3) 'rdcps' returns all zeros and 4) 'wrcps'
behaves as a NOP.

So we'll need about 3 new elf capability flags in the end to represent
all of these things.

Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-27 22:10:10 -07:00
David S. Miller
314ff52727 sparc: Don't do expensive hypervisor PCR write unless necessary.
The hypervisor call is only necessary if hypervisor events are
being requested.

So if we're not tracking hypervisor events, simply do a direct
register write.

Signed-off-by: David S. Miller <davem@davemloft.net>
2011-07-27 20:46:25 -07:00