Interrupt Group 4 mapps the GPIO pins enabled as interrupt sources;
add defines to make this clear when addressing them later in code.
The mapped GPIOs support triggering on either level high or low. To
achieve this, the set_type() function calls rb532_gpio_set_ilevel() for
interrupts of the above mentioned group.
As there is no way to alter the triggering characteristics of the other
interrupts, accept level triggering on status high only. (This is just a
guess; but as the system boots fine and interrupt-driven devices (e.g.
serial console) work with no implications, it seems to be right.)
To clear a GPIO mapped IRQ, the source has to be cleared (i.e., the
interrupt status bit of the corresponding GPIO pin). This is done inside
rb532_disable_irq().
After applying these changes I could undo most of my former "fixes" to
pata-rb532-cf. Particularly all interrupt handling can be done
generically via set_irq_type() as it was before.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The code is rather based on trial-and-error than knowledge. Verified Via
Rhine functionality in PIO as well as MMIO mode.
[Looks sane -- Ralf]
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The algorithm works unconditionally. If bitval is one, the first line is
a no op and the second line sets the bit at offset position. Vice versa,
if bitval is zero, the first line clears the bit at offset position and
the second line is a no op.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The previous definition inadvertently omits Octeon which currently is
treated as an architecture variant separate from MIPS32 and MIPS64.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If a context switch occurred between the watch exception and reading the
watch registers, it would be possible for the new process to corrupt their
state. Enabling interrupts only after the watch registers are read avoids
this race.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This fixes the ptrace ABI for watch registers, and should allow 64bit
kernels to use the watch register support.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The special IP27 DMA code selected by DMA_IP27 has been removed a while
ago turning DMA_IP27 into almost a nop. Also fixup the broken logic of
its last users memcpy.S and memcpy-inatomic.s.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This shaves of 1912 bytes of an IP27 defconfig kernel and avoids
unexpected overflow behaviour in atomic_sub_if_positive. Apply the same
changes to the atomic64_* functions for consistency.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Now that all EEPROM drivers live in the same place, let's harmonize
their symbol names.
Also fix eeprom's dependencies, it definitely needs sysfs, and is no
longer experimental after many years in the kernel tree.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Impact: fix build errors
Since the SPARSE IRQS changes redefined how the kstat irqs are
organized, arch's must use the new accessor function:
kstat_incr_irqs_this_cpu(irq, DESC);
If CONFIG_SPARSE_IRQS is set, then DESC is a pointer to the
irq_desc which has a pointer to the kstat_irqs. If not, then
the .irqs field of struct kernel_stat is used instead.
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'syscalls' of git://git390.osdl.marist.edu/pub/scm/linux-2.6: (44 commits)
[CVE-2009-0029] s390 specific system call wrappers
[CVE-2009-0029] System call wrappers part 33
[CVE-2009-0029] System call wrappers part 32
[CVE-2009-0029] System call wrappers part 31
[CVE-2009-0029] System call wrappers part 30
[CVE-2009-0029] System call wrappers part 29
[CVE-2009-0029] System call wrappers part 28
[CVE-2009-0029] System call wrappers part 27
[CVE-2009-0029] System call wrappers part 26
[CVE-2009-0029] System call wrappers part 25
[CVE-2009-0029] System call wrappers part 24
[CVE-2009-0029] System call wrappers part 23
[CVE-2009-0029] System call wrappers part 22
[CVE-2009-0029] System call wrappers part 21
[CVE-2009-0029] System call wrappers part 20
[CVE-2009-0029] System call wrappers part 19
[CVE-2009-0029] System call wrappers part 18
[CVE-2009-0029] System call wrappers part 17
[CVE-2009-0029] System call wrappers part 16
[CVE-2009-0029] System call wrappers part 15
...
Add swab.h to kbuild.asm and remove the individual entries from
each arch, mark as unifdef as some arches have some kernel-only
bits inside.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: cleanup, update to new cpumask API
Irq_desc.affinity and irq_desc.pending_mask are now cpumask_var_t's
so access to them should be using the new cpumask API.
Signed-off-by: Mike Travis <travis@sgi.com>
Impact: build fix
Ingo Molnar wrote:
> tip/arch/blackfin/kernel/irqchip.c: In function 'show_interrupts':
> tip/arch/blackfin/kernel/irqchip.c:85: error: 'struct kernel_stat' has no member named 'irqs'
> make[2]: *** [arch/blackfin/kernel/irqchip.o] Error 1
> make[2]: *** Waiting for unfinished jobs....
>
So could move kstat_irqs array to irq_desc struct.
(s390, m68k, sparc) are not touched yet, because they don't support genirq
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Replace the current sysctl-based suspend interface with a new sysfs-
based one which also uses the Linux-2.6 suspend model.
To configure wakeup sources, a subtree for the demoboards is created
under /sys/power/db1x:
sys/
`-- power
`-- db1x
|-- gpio0
|-- gpio1
|-- gpio2
|-- gpio3
|-- gpio4
|-- gpio5
|-- gpio6
|-- gpio7
|-- timer
|-- timer_timeout
|-- wakemsk
`-- wakesrc
The nodes 'gpio[0-7]' and 'timer' configure the GPIO0..7 and M2
bits of the SYS_WAKEMSK (wakeup source enable) register. Writing '1'
enables a wakesource, 0 disables it.
The 'timer_timeout' node holds the timeout in seconds after which the
TOYMATCH2 event should wake the system.
The 'wakesrc' node holds the SYS_WAKESRC register after wakeup (in hex),
the 'wakemsk' node can be used to get/set the wakeup mask directly.
For example, to have the timer wake the system after 10 seconds of sleep,
the following must be done in userspace:
echo 10 > /sys/power/db1x/timer_timeout
echo 1 > /sys/power/db1x/timer
echo mem > /sys/power/sleep
This patch also removes the homebrew CPU frequency switching code. I don't
understand how it could have ever worked reliably; it does not communicate
the clock changes to peripheral devices other than uarts.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
create mode 100644 arch/mips/alchemy/devboards/pm.c
Implement suspend/resume for DBDMA controller and its channels.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Au1550/Au1200 have a different memory controller which requires additi-
onal code to properly put memory to sleep (code taken from AMD/RMI's
Linux-2.6.11 source package).
Also fix up the remaining pm-related paths to compile on Au1200/Au1550
platforms.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Now that nothing in time.c depends on calc_clock, it can
be moved to clocks.c where it belongs.
While at it, give it a better non-generic name and call it
as soon as possible in plat_mem_init.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for the 32 kHz counter1 (RTC) as clocksource / clockevent
device. As a nice side effect, this also enables use of the 'wait'
instruction for runtime idle power savings.
If the counters aren't enabled/working properly, fall back on the
cp0 counter clock code.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The current mips clock build infrastructure lets a system only use
either the MIPS cp0 counter or a SoC specific timer as a clocksource /
clockevent device.
This patch renames the core cp0 counter clocksource / clockevent functions
from mips_* to r4k_* and updates the wrappers in asm-mips/time.h to
call these renamed functions instead.
Chips which can detect whether it is safe to use a chip-specific timer
can now fall back on the cp0 counter if necessary and possible
(e.g. Alchemy with a follow-on patch).
Existing behaviour is not changed in any way.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the cpu_table:
- move detection of whether c0_config[OD] is read-only and should be set
to fix various chip errata to au1000 headers.
- move detection of write-only sys_cpupll to au1000 headers.
- remove the BCLK switching code: Activation of this features should be
left to the boards using the chips since it also affects external devices
tied to BCLK, and only the board designers know whether it is safe to
enable.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
delete mode 100644 arch/mips/alchemy/common/cputable.c
There are no in-tree users, so remove them.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch attempts to modernize core Alchemy interrupt handling code.
- add irq_chips for irq controllers instead of irq type,
- add a set_type() hook to change irq trigger type during runtime,
- add a set_wake() hook to control GPIO0..7 based wakeup,
- use linux' IRQF_TRIGGER_ constants instead of homebrew ones,
- enable GENERIC_HARDIRQS_NO__DO_IRQ.
- simplify plat_irq_dispatch
- merge au1xxx_irqmap into irq.c file, the only place where its
contents are referenced.
- board_init_irq() is now mandatory for every board; use it to register
the remaining (gpio-based) interrupt sources; update all boards
accordingly.
Run-tested on Db1200 and other Au1200 based platforms.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
delete mode 100644 arch/mips/alchemy/common/au1xxx_irqmap.c
Not every alchemy-based board might want these options forced on it,
and most of this stuff seems to be intended for devboard code anyway.
Remove commandline mangling code out of common chip code and instead
add relevant sections to all in-tree boards to not change existing
behaviour.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This should ease sharing of common devboard code.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We add a dev parameter to plat_unmap_dma_mem(), and hooks for
plat_dma_supported() and plat_extra_sync_for_device() which should be
nop changes for all existing targets.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Expand the case statement for build_tlb_write_entry so that it does
the right thing on Cavium CPU variants.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: Paul Gortmaker <Paul.Gortmaker@windriver.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For Cavium OCTEON, compute the return epc value for OCTEON specific
branch instructions.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For OCTEON, implement a save and restore of the multiplier state
across context switches.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add in the cop2 and cvmseg state info to the known proc reg
data for Cavium so that it can be tracked, saved, restored.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Take all the OCTEON specific files that were added, and hook them into
the build system for the arch/mips. For versions of GCC that lack
OCTEON support, override gas target architecture.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Follow precedent of other boards, and hook-up the CPU specific cache
init.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add OCTEON constants to asm/cpu.h and asm/module.h.
Add probe function for Cavium OCTEON CPUs and hook it up.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Gas from binutils 2.19 fails to compile some cop1 instructions with
-march=octeon. Since the cop1 instructions are present in mips1, use
that arch instead. This will be fixed in binutils 2.20.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If on Cavium, be aware of cop2 and hwrena during do_cpu().
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: Paul Gortmaker <Paul.Gortmaker@windriver.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For Cavium CPU, we treat the same as R10000, in that all hazards
are dealt with in hardware.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: Paul Gortmaker <Paul.Gortmaker@windriver.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These files are used to coordinate resource sharing between all of
the programs running on the OCTEON SOC. The OCTEON processor has many
CPU cores (current parts have up to 16, but more are possible). It
also has a variety of on-chip hardware blocks for things like network
acceleration, encryption and RAID.
One typical configuration is to run Linux on several of the CPU cores,
and other dedicated applications on the other cores.
Resource allocation between the various programs running on the system
(Linux kernel and other dedicated applications) needs to be
coordinated. The code we use to do this we call the 'executive'. All
of this resource allocation and sharing code is gathered together in
the executive directory.
Included in the patch set are the following files:
cvmx-bootmem.c and cvmx-sysinfo.c -- Coordinate memory allocation.
All memory used by the Linux kernel is obtained here at boot time.
cvmx-l2c.c -- Coordinates operations on the shared level 2 cache.
octeon-model.c -- Probes chip capabilities and version.
The corresponding headers are in asm/octeon.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
create mode 100644 arch/mips/cavium-octeon/executive/Makefile
create mode 100644 arch/mips/cavium-octeon/executive/cvmx-bootmem.c
create mode 100644 arch/mips/cavium-octeon/executive/cvmx-l2c.c
create mode 100644 arch/mips/cavium-octeon/executive/cvmx-sysinfo.c
create mode 100644 arch/mips/cavium-octeon/executive/octeon-model.c
create mode 100644 arch/mips/include/asm/octeon/cvmx-asm.h
create mode 100644 arch/mips/include/asm/octeon/cvmx-bootinfo.h
create mode 100644 arch/mips/include/asm/octeon/cvmx-bootmem.h
create mode 100644 arch/mips/include/asm/octeon/cvmx-l2c.h
create mode 100644 arch/mips/include/asm/octeon/cvmx-packet.h
create mode 100644 arch/mips/include/asm/octeon/cvmx-spinlock.h
create mode 100644 arch/mips/include/asm/octeon/cvmx-sysinfo.h
create mode 100644 arch/mips/include/asm/octeon/cvmx.h
create mode 100644 arch/mips/include/asm/octeon/octeon-feature.h
create mode 100644 arch/mips/include/asm/octeon/octeon-model.h
Here we define the addresses and bit-fields of the Configuration and
Status Registers (CSRs) for some of the hardware functional units on
the OCTEON SOC.
Definitions are needed for:
CIU -- Central Interrupt Unit.
GPIO -- General Purpose Input Output.
IOB -- Input / Output {Busing,Bridge}.
IPD -- Input Packet Data unit.
L2C -- Level-2 Cache controller.
L2D -- Level-2 Data cache.
L2T -- Level-2 cache Tag.
LED -- Light Emitting Diode controller.
MIO -- Miscellaneous Input / Output.
POW -- Packet Order / Work unit.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since memsize is unsigned, it would seem better to use strict_strtoul that
strict_strtol.
A simplified version of the semantic patch that makes this change is as
follows: (http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@s2@
long e;
position p;
@@
strict_strtol@p(...,&e)
@@
position p != s2.p;
type T;
T e;
@@
- strict_strtol@p
+ strict_strtoul
(...,&e)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (98 commits)
PCI PM: Put PM callbacks in the order of execution
PCI PM: Run default PM callbacks for all devices using new framework
PCI PM: Register power state of devices during initialization
PCI PM: Call pci_fixup_device from legacy routines
PCI PM: Rearrange code in pci-driver.c
PCI PM: Avoid touching devices behind bridges in unknown state
PCI PM: Move pci_has_legacy_pm_support
PCI PM: Power-manage devices without drivers during suspend-resume
PCI PM: Add suspend counterpart of pci_reenable_device
PCI PM: Fix poweroff and restore callbacks
PCI: Use msleep instead of cpu_relax during ASPM link retraining
PCI: PCIe portdrv: Add kerneldoc comments to remining core funtions
PCI: PCIe portdrv: Rearrange code so that related things are together
PCI: PCIe portdrv: Fix suspend and resume of PCI Express port services
PCI: PCIe portdrv: Add kerneldoc comments to some core functions
x86/PCI: Do not use interrupt links for devices using MSI-X
net: sfc: Use pci_clear_master() to disable bus mastering
PCI: Add pci_clear_master() as opposite of pci_set_master()
PCI hotplug: remove redundant test in cpq hotplug
PCI: pciehp: cleanup register and field definitions
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
Use the generic pci_common_swizzle() instead of arch-specific code.
Note that pci_common_swizzle() loops based on dev->bus->self, not
dev->bus->parent as the mips common_swizzle() did. I think they
are equivalent for this purpose.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The atomic_t type cannot currently be used in some header files because it
would create an include loop with asm/atomic.h. Move the type definition
to linux/types.h to break the loop.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
/proc/*/stack adds the ability to query a task's stack trace. It is more
useful than /proc/*/wchan as it provides full stack trace instead of single
depth. Example output:
$ cat /proc/self/stack
[<c010a271>] save_stack_trace_tsk+0x17/0x35
[<c01827b4>] proc_pid_stack+0x4a/0x76
[<c018312d>] proc_single_show+0x4a/0x5e
[<c016bdec>] seq_read+0xf3/0x29f
[<c015a004>] vfs_read+0x6d/0x91
[<c015a0c1>] sys_read+0x3b/0x60
[<c0102eda>] syscall_call+0x7/0xb
[<ffffffff>] 0xffffffff
[add save_stack_trace_tsk() on mips, ACK Ralf --adobriyan]
Signed-off-by: Ken Chen <kenchen@google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
* 'cpus4096-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (77 commits)
x86: setup_per_cpu_areas() cleanup
cpumask: fix compile error when CONFIG_NR_CPUS is not defined
cpumask: use alloc_cpumask_var_node where appropriate
cpumask: convert shared_cpu_map in acpi_processor* structs to cpumask_var_t
x86: use cpumask_var_t in acpi/boot.c
x86: cleanup some remaining usages of NR_CPUS where s/b nr_cpu_ids
sched: put back some stack hog changes that were undone in kernel/sched.c
x86: enable cpus display of kernel_max and offlined cpus
ia64: cpumask fix for is_affinity_mask_valid()
cpumask: convert RCU implementations, fix
xtensa: define __fls
mn10300: define __fls
m32r: define __fls
h8300: define __fls
frv: define __fls
cris: define __fls
cpumask: CONFIG_DISABLE_OBSOLETE_CPUMASK_FUNCTIONS
cpumask: zero extra bits in alloc_cpumask_var_node
cpumask: replace for_each_cpu_mask_nr with for_each_cpu in kernel/time/
cpumask: convert mm/
...
* 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (66 commits)
x86: export vector_used_by_percpu_irq
x86: use logical apicid in x2apic_cluster's x2apic_cpu_mask_to_apicid_and()
sched: nominate preferred wakeup cpu, fix
x86: fix lguest used_vectors breakage, -v2
x86: fix warning in arch/x86/kernel/io_apic.c
sched: fix warning in kernel/sched.c
sched: move test_sd_parent() to an SMP section of sched.h
sched: add SD_BALANCE_NEWIDLE at MC and CPU level for sched_mc>0
sched: activate active load balancing in new idle cpus
sched: bias task wakeups to preferred semi-idle packages
sched: nominate preferred wakeup cpu
sched: favour lower logical cpu number for sched_mc balance
sched: framework for sched_mc/smt_power_savings=N
sched: convert BALANCE_FOR_xx_POWER to inline functions
x86: use possible_cpus=NUM to extend the possible cpus allowed
x86: fix cpu_mask_to_apicid_and to include cpu_online_mask
x86: update io_apic.c to the new cpumask code
x86: Introduce topology_core_cpumask()/topology_thread_cpumask()
x86: xen: use smp_call_function_many()
x86: use work_on_cpu in x86/kernel/cpu/mcheck/mce_amd_64.c
...
Fixed up trivial conflict in kernel/time/tick-sched.c manually
Impact: New APIs
The old node_to_cpumask/node_to_pcibus returned a cpumask_t: these
return a pointer to a struct cpumask. Part of removing cpumasks from
the stack.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ralf Baechle <ralf@linux-mips.org>
The way the code is written it was assuming dshd has the function of a
hypothetical dshw instruction ...
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Impact: change calling convention of existing clock_event APIs
struct clock_event_timer's cpumask field gets changed to take pointer,
as does the ->broadcast function.
Another single-patch change. For safety, we BUG_ON() in
clockevents_register_device() if it's not set.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
Impact: change existing irq_chip API
Not much point with gentle transition here: the struct irq_chip's
setaffinity method signature needs to change.
Fortunately, not widely used code, but hits a few architectures.
Note: In irq_select_affinity() I save a temporary in by mangling
irq_desc[irq].affinity directly. Ingo, does this break anything?
(Folded in fix from KOSAKI Motohiro)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Acked-by: Ingo Molnar <mingo@redhat.com>
Cc: ralf@linux-mips.org
Cc: grundler@parisc-linux.org
Cc: jeremy@xensource.com
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Impact: change calling convention of existing cpumask APIs
Most cpumask functions started with cpus_: these have been replaced by
cpumask_ ones which take struct cpumask pointers as expected.
These four functions don't have good replacement names; fortunately
they're rarely used, so we just change them over.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: paulus@samba.org
Cc: mingo@redhat.com
Cc: tony.luck@intel.com
Cc: ralf@linux-mips.org
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: cl@linux-foundation.org
Cc: srostedt@redhat.com
Impact: cleanup
Each SMP arch defines these themselves. Move them to a central
location.
Twists:
1) Some archs (m32, parisc, s390) set possible_map to all 1, so we add a
CONFIG_INIT_ALL_POSSIBLE for this rather than break them.
2) mips and sparc32 '#define cpu_possible_map phys_cpu_present_map'.
Those archs simply have phys_cpu_present_map replaced everywhere.
3) Alpha defined cpu_possible_map to cpu_present_map; this is tricky
so I just manipulate them both in sync.
4) IA64, cris and m32r have gratuitous 'extern cpumask_t cpu_possible_map'
declarations.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Tested-by: Tony Luck <tony.luck@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Mike Travis <travis@sgi.com>
Cc: ink@jurassic.park.msu.ru
Cc: rmk@arm.linux.org.uk
Cc: starvik@axis.com
Cc: tony.luck@intel.com
Cc: takata@linux-m32r.org
Cc: ralf@linux-mips.org
Cc: grundler@parisc-linux.org
Cc: paulus@samba.org
Cc: schwidefsky@de.ibm.com
Cc: lethal@linux-sh.org
Cc: wli@holomorphy.com
Cc: davem@davemloft.net
Cc: jdike@addtoit.com
Cc: mingo@redhat.com
dma_free_noncoherent() and dma_free_coherent() are missing calls to
plat_unmap_dma_mem(). This patch adds them.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The header path in the help text for the RUNTIME_DEBUG config option is
obsolete and needs to be updated to match the new location of
architecture-specific header files. While at it, fix the spelling mistake.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For MIPS R2, use the EI and DI instructions to enable and disable
interrupts.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Certain X11 servers such as the SIS server will only work if PCI mmap is
implemented. This patch implements PCI mmap but to be on the same side
so close to a release it only supports uncached mappings so performance
will not be optimal for some uses such as framebuffers.
Thanks to Zhang Le <r0bertz@gentoo.org> for the original report and
testing.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When the o32 errno was changed to ENOSYS, we forgot to update the code
for 64bit kernels.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The syscall code was assuming splice only takes 4 arguments so no stack
arguments were being copied from the userspace stack to the kernel stack.
As the result splice was likely to fail with EINVAL.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These haven't seen much attention for too long but particularly important
enable RTC_CLASS and CONFIG_RTC_HCTOSYS so the wall clock time is set on
kernel startup.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With the conversion of MIPS to RTC_LIB the old RTC driver CONFIG_RTC became
unselectable. Fix by setting up a platform device. Also enable
RTC_CLASS so system time gets set from RTC on kernel initialization.
[Ralf: Original patch by Tiejun; polished nice and shiny by me]
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On a 64 bit kernel if an o32 syscall was made with a syscall number less
than 4000, we would read the function from outside of the bounds of the
syscall table. This led to non-deterministic behavior including system
crashes.
While we were at it we reworked the 32 bit version as well to use fewer
instructions. Both 32 and 64 bit versions are use the same code now.
Signed-off-by: Vlad Malov <Vlad.Malov@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Conflicts:
fs/nfsd/nfs4recover.c
Manually fixed above to use new creds API functions, e.g.
nfs4_save_creds().
Signed-off-by: James Morris <jmorris@namei.org>
All architectures now use the generic compat_sys_ptrace, as should every
new architecture that needs 32bit compat (if we'll ever get another).
Remove the now superflous __ARCH_WANT_COMPAT_SYS_PTRACE define, and also
kill a comment about __ARCH_SYS_PTRACE that was added after
__ARCH_SYS_PTRACE was already gone.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mathieu Desnoyers reported this build failure on powerpc:
kernel/sched.c: In function 'sd_init_NODE':
kernel/sched.c:7319: error: non-static initialization of a flexible array member
kernel/sched.c:7319: error: (near initialization for '(anonymous)')
this happens because .span changed to cpumask_var_t, hence
the static CPU_MASK_NONE initializers in the SD_*_INIT
templates are not type-correct anymore.
Remove them, as they default to empty anyway.
Also remove them from IA64, MIPS and SH.
Reported-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Often we do things like put BUG() in the default clause of a case
statement. Since it was not declared __noreturn, this could sometimes
lead to bogus compiler warnings that variables were used
uninitialized.
There is a small problem in that we have to put a magic while(1); loop to
fool GCC into really thinking it is noreturn. This makes the new
BUG() function 3 instructions long instead of just 1, but I think it
is worth it as it is now unnecessary to do extra work to silence the
'used uninitialized' warnings.
I also re-wrote BUG_ON so that if it is given a constant condition, it
just does BUG() instead of loading a constant value in to a register
and testing it.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As gpiolib doesn't support pin multiplexing, it provides no way to
access the GPIOFUNC register. Also there is no support for setting
interrupt status and level. These functions provide access to them and
are needed by the CompactFlash driver.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The indy_sc_ops variable in arch/mips/mm/sc-ip22.c is needlessly defined
global, and this patch makes it static.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
This patch fixes the wrong use of GPIO register offsets
in devices.c. To avoid further problems, use gpio_get_value
to return the NAND status instead of our own expanded code.
Also define the zero offset of the alternate function register to allow
consistent access.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On linux-queue, malta doesn't build after the include file relocation.
This should fix it.
There some occurrences of 'asm-mips' in the comments of quite a few
files, but this is the only place I found it in any code.
Signed-off-by: David Daney <ddaney@avtrex.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Attach creds to file structs and discard f_uid/f_gid.
file_operations::open() methods (such as hppfs_open()) should use file->f_cred
rather than current_cred(). At the moment file->f_cred will be current_cred()
at this point.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <jmorris@namei.org>
Signed-off-by: James Morris <jmorris@namei.org>
Separate the task security context from task_struct. At this point, the
security data is temporarily embedded in the task_struct with two pointers
pointing to it.
Note that the Alpha arch is altered as it refers to (E)UID and (E)GID in
entry.S via asm-offsets.
With comment fixes Signed-off-by: Marc Dionne <marc.c.dionne@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
Wrap access to task credentials so that they can be separated more easily from
the task_struct during the introduction of COW creds.
Change most current->(|e|s|fs)[ug]id to current_(|e|s|fs)[ug]id().
Change some task->e?[ug]id to task_e?[ug]id(). In some places it makes more
sense to use RCU directly rather than a convenient wrapper; these will be
addressed by later patches.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Signed-off-by: James Morris <jmorris@namei.org>
Impact: cleanup, change .config option name
We had this ugly config name for a long time for hysteric raisons.
Rename it to a saner name.
We still cannot get rid of it completely, until /proc/<pid>/stack
usage replaces WCHAN usage for good.
We'll be able to do that in the v2.6.29/v2.6.30 timeframe.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It was only used by this one SGI platform which recently was converted to
RTC_LIB and with RTC_LIB enabled the legacy drivers are no more selectable.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It was only used by two SGI platforms which recently were converted to
RTC_LIB and with RTC_LIB enabled the legacy drivers are no more selectable.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
As noticed by David Daney <ddaney@caviumnetworks.com>, the old long switch
statement did not comply with the Linux C coding style. It was also yet
another place of code to be changed when adding a new processor type
leading to annoying bugs for example in /proc/cpuinfo.
Fixed by moving the setting of the CPU type string into the core of the
probing code and a few BUG_ON() test to ensure the CPU probing code indeed
did its job and removing multiple now redundant tests.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Arguably using the address error handler has always been ugly. But with
processors that handle unaligned loads and stores in hardware the
current mechanism ceases to work so switch it to a BREAK instruction and
allocate break code 514 to the FPU emulator.
Yoichi Yuasa provided a build fix for CONFIG_BUG=n.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
A system isn't necessarily booted on physical processor 0 as this code
assumes. Also the array happens to be allocated in .bss so it's zero
initialized anyway. Systems which need to override this can do so in
their mp_ops->smp_setup() method.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It just so happens to be zero on all currently supported systems so this
hasn't bitten yet ...
[Ralf: Original patch from Cavium; handling of set_uncached_handler() and
de-ifdef'ed trap_init() implementation by me.]
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When booting Linux on a txx9 board with VxWorks boot loader, it crashes in
prom_getenv(), as VxWorks doesn't pass firmware parameters in a0-a3 (in my
case, the actual leftover values in these registers were 0x80002000,
0x80001fe0, 0x2000, and 0x20).
Make the parsing of argc, argv, and envp a bit more robust by checking if
argc is a number below CKSEG0, and argv/envp point to CKSEG0.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove runtime db_* macros as we don't need them any more. In general,
such helpers are useful for initial porting, but once approved, they are
not indispensable.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Current EMMA2RH irq code is mess. Before cleaning it up, gather them
in one place as a first step.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Let's use immediate value, instead. This also saves memory footprint,
and probably a little bit faster.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Let's use immediate value, instead. This also saves memory footprint,
and probably a little bit faster.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Let's use immediate value, instead. This also saves memory footprint,
and probably a little bit faster.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We'll put all EMMA related headers there in the future.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
git mv arch/mips/{emma2rh,emma} and fixups Makefiles. We'll put all NEC
EMMA series based machines there in the future.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- Move EMMA related stuff into arch/mips/emma/Kconfig
- Create CONFIG_SOC_EMMA* to handle more EMMA SoCs effectively
- Rename CONFIG_MARKEINS into CONFIG_NEC_MARKEINS
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
