Upon CPU shutdown and consequent warm-reboot, the hypervisor CPU state
must be re-initialized. This patch implements a CPU PM notifier that
upon warm-boot calls a KVM hook to reinitialize properly the hypervisor
state so that the CPU can be safely resumed.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
When a CPU enters a low power state, its FP register content is lost.
This patch adds a notifier to save the FP context on CPU shutdown
and restore it on CPU resume. The context is saved and restored only
if the suspending thread is not a kernel thread, mirroring the current
context switch behaviour.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Kernel subsystems like CPU idle and suspend to RAM require a generic
mechanism to suspend a processor, save its context and put it into
a quiescent state. The cpu_{suspend}/{resume} implementation provides
such a framework through a kernel interface allowing to save/restore
registers, flush the context to DRAM and suspend/resume to/from
low-power states where processor context may be lost.
The CPU suspend implementation relies on the suspend protocol registered
in CPU operations to carry out a suspend request after context is
saved and flushed to DRAM. The cpu_suspend interface:
int cpu_suspend(unsigned long arg);
allows to pass an opaque parameter that is handed over to the suspend CPU
operations back-end so that it can take action according to the
semantics attached to it. The arg parameter allows suspend to RAM and CPU
idle drivers to communicate to suspend protocol back-ends; it requires
standardization so that the interface can be reused seamlessly across
systems, paving the way for generic drivers.
Context memory is allocated on the stack, whose address is stashed in a
per-cpu variable to keep track of it and passed to core functions that
save/restore the registers required by the architecture.
Even though, upon successful execution, the cpu_suspend function shuts
down the suspending processor, the warm boot resume mechanism, based
on the cpu_resume function, makes the resume path operate as a
cpu_suspend function return, so that cpu_suspend can be treated as a C
function by the caller, which simplifies coding the PM drivers that rely
on the cpu_suspend API.
Upon context save, the minimal amount of memory is flushed to DRAM so
that it can be retrieved when the MMU is off and caches are not searched.
The suspend CPU operation, depending on the required operations (eg CPU vs
Cluster shutdown) is in charge of flushing the cache hierarchy either
implicitly (by calling firmware implementations like PSCI) or explicitly
by executing the required cache maintainance functions.
Debug exceptions are disabled during cpu_{suspend}/{resume} operations
so that debug registers can be saved and restored properly preventing
preemption from debug agents enabled in the kernel.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Power management software requires the kernel to save and restore
CPU registers while going through suspend and resume operations
triggered by kernel subsystems like CPU idle and suspend to RAM.
This patch implements code that provides save and restore mechanism
for the arm v8 implementation. Memory for the context is passed as
parameter to both cpu_do_suspend and cpu_do_resume functions, and allows
the callers to implement context allocation as they deem fit.
The registers that are saved and restored correspond to the registers set
actually required by the kernel to be up and running which represents a
subset of v8 ISA.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
On ARM64 SMP systems, cores are identified by their MPIDR_EL1 register.
The MPIDR_EL1 guidelines in the ARM ARM do not provide strict enforcement of
MPIDR_EL1 layout, only recommendations that, if followed, split the MPIDR_EL1
on ARM 64 bit platforms in four affinity levels. In multi-cluster
systems like big.LITTLE, if the affinity guidelines are followed, the
MPIDR_EL1 can not be considered a linear index. This means that the
association between logical CPU in the kernel and the HW CPU identifier
becomes somewhat more complicated requiring methods like hashing to
associate a given MPIDR_EL1 to a CPU logical index, in order for the look-up
to be carried out in an efficient and scalable way.
This patch provides a function in the kernel that starting from the
cpu_logical_map, implement collision-free hashing of MPIDR_EL1 values by
checking all significative bits of MPIDR_EL1 affinity level bitfields.
The hashing can then be carried out through bits shifting and ORing; the
resulting hash algorithm is a collision-free though not minimal hash that can
be executed with few assembly instructions. The mpidr_el1 is filtered through a
mpidr mask that is built by checking all bits that toggle in the set of
MPIDR_EL1s corresponding to possible CPUs. Bits that do not toggle do not
carry information so they do not contribute to the resulting hash.
Pseudo code:
/* check all bits that toggle, so they are required */
for (i = 1, mpidr_el1_mask = 0; i < num_possible_cpus(); i++)
mpidr_el1_mask |= (cpu_logical_map(i) ^ cpu_logical_map(0));
/*
* Build shifts to be applied to aff0, aff1, aff2, aff3 values to hash the
* mpidr_el1
* fls() returns the last bit set in a word, 0 if none
* ffs() returns the first bit set in a word, 0 if none
*/
fs0 = mpidr_el1_mask[7:0] ? ffs(mpidr_el1_mask[7:0]) - 1 : 0;
fs1 = mpidr_el1_mask[15:8] ? ffs(mpidr_el1_mask[15:8]) - 1 : 0;
fs2 = mpidr_el1_mask[23:16] ? ffs(mpidr_el1_mask[23:16]) - 1 : 0;
fs3 = mpidr_el1_mask[39:32] ? ffs(mpidr_el1_mask[39:32]) - 1 : 0;
ls0 = fls(mpidr_el1_mask[7:0]);
ls1 = fls(mpidr_el1_mask[15:8]);
ls2 = fls(mpidr_el1_mask[23:16]);
ls3 = fls(mpidr_el1_mask[39:32]);
bits0 = ls0 - fs0;
bits1 = ls1 - fs1;
bits2 = ls2 - fs2;
bits3 = ls3 - fs3;
aff0_shift = fs0;
aff1_shift = 8 + fs1 - bits0;
aff2_shift = 16 + fs2 - (bits0 + bits1);
aff3_shift = 32 + fs3 - (bits0 + bits1 + bits2);
u32 hash(u64 mpidr_el1) {
u32 l[4];
u64 mpidr_el1_masked = mpidr_el1 & mpidr_el1_mask;
l[0] = mpidr_el1_masked & 0xff;
l[1] = mpidr_el1_masked & 0xff00;
l[2] = mpidr_el1_masked & 0xff0000;
l[3] = mpidr_el1_masked & 0xff00000000;
return (l[0] >> aff0_shift | l[1] >> aff1_shift | l[2] >> aff2_shift |
l[3] >> aff3_shift);
}
The hashing algorithm relies on the inherent properties set in the ARM ARM
recommendations for the MPIDR_EL1. Exotic configurations, where for instance
the MPIDR_EL1 values at a given affinity level have large holes, can end up
requiring big hash tables since the compression of values that can be achieved
through shifting is somewhat crippled when holes are present. Kernel warns if
the number of buckets of the resulting hash table exceeds the number of
possible CPUs by a factor of 4, which is a symptom of a very sparse HW
MPIDR_EL1 configuration.
The hash algorithm is quite simple and can easily be implemented in assembly
code, to be used in code paths where the kernel virtual address space is
not set-up (ie cpu_resume) and instruction and data fetches are strongly
ordered so code must be compact and must carry out few data accesses.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
In order to simplify access to different affinity levels within the
MPIDR_EL1 register values, this patch implements some preprocessor
macros that allow to retrieve the MPIDR_EL1 affinity level value according
to the level passed as input parameter.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
For NUMA systems, initializing the blk-mq layer and using per node hctx.
We initialize submit queues to 1, while blk-mq nr_hw_queues is
initialized to the number of NUMA nodes.
This makes the null_init_hctx function overwrite memory outside of what
it allocated. In my case it lead to writing garbage into struct
request_queue's mq_map.
Signed-off-by: Matias Bjorling <m@bjorling.me>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking fixes from David Miller:
1) Revert CHECKSUM_COMPLETE optimization in pskb_trim_rcsum(), I can't
figure out why it breaks things.
2) Fix comparison in netfilter ipset's hash_netnet4_data_equal(), it
was basically doing "x == x", from Dave Jones.
3) Freescale FEC driver was DMA mapping the wrong number of bytes, from
Sebastian Siewior.
4) Blackhole and prohibit routes in ipv6 were not doing the right thing
because their ->input and ->output methods were not being assigned
correctly. Now they behave properly like their ipv4 counterparts.
From Kamala R.
5) Several drivers advertise the NETIF_F_FRAGLIST capability, but
really do not support this feature and will send garbage packets if
fed fraglist SKBs. From Eric Dumazet.
6) Fix long standing user triggerable BUG_ON over loopback in RDS
protocol stack, from Venkat Venkatsubra.
7) Several not so common code paths can potentially try to invoke
packet scheduler actions that might be NULL without checking. Shore
things up by either 1) defining a method as mandatory and erroring
on registration if that method is NULL 2) defininig a method as
optional and the registration function hooks up a default
implementation when NULL is seen. From Jamal Hadi Salim.
8) Fix fragment detection in xen-natback driver, from Paul Durrant.
9) Kill dangling enter_memory_pressure method in cg_proto ops, from
Eric W Biederman.
10) SKBs that traverse namespaces should have their local_df cleared,
from Hannes Frederic Sowa.
11) IOCB file position is not being updated by macvtap_aio_read() and
tun_chr_aio_read(). From Zhi Yong Wu.
12) Don't free virtio_net netdev before releasing all of the NAPI
instances. From Andrey Vagin.
13) Procfs entry leak in xt_hashlimit, from Sergey Popovich.
14) IPv6 routes that are no cached routes should not count against the
garbage collection limits. We had this almost right, but were
missing handling addrconf generated routes properly. From Hannes
Frederic Sowa.
15) fib{4,6}_rule_suppress() have to consider potentially seeing NULL
route info when they are called, from Stefan Tomanek.
16) TUN and MACVTAP have had truncated packet signalling for some time,
fix from Jason Wang.
17) Fix use after frrr in __udp4_lib_rcv(), from Eric Dumazet.
18) xen-netback does not interpret the NAPI budget properly for TX work,
fix from Paul Durrant.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (132 commits)
igb: Fix for issue where values could be too high for udelay function.
i40e: fix null dereference
xen-netback: fix gso_prefix check
net: make neigh_priv_len in struct net_device 16bit instead of 8bit
drivers: net: cpsw: fix for cpsw crash when build as modules
xen-netback: napi: don't prematurely request a tx event
xen-netback: napi: fix abuse of budget
sch_tbf: use do_div() for 64-bit divide
udp: ipv4: must add synchronization in udp_sk_rx_dst_set()
net:fec: remove duplicate lines in comment about errata ERR006358
Revert "8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature"
8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature
xen-netback: make sure skb linear area covers checksum field
net: smc91x: Fix device tree based configuration so it's usable
udp: ipv4: fix potential use after free in udp_v4_early_demux()
macvtap: signal truncated packets
tun: unbreak truncated packet signalling
net: sched: htb: fix the calculation of quantum
net: sched: tbf: fix the calculation of max_size
micrel: add support for KSZ8041RNLI
...
Pull x86 fixes from Peter Anvin:
"This is a pretty small batch:
The biggest single change is to stop using EFI time services on 32-bit
platforms. This matches our current behavior on 64-bit platforms as
we already had ruled them out there as being too unreliable. Turns
out that affects 32-bit platforms, too.
One NULL pointer fix for SGI UV.
Two minor build fixes, one of which only affects icc and the other
which affects icc and future versions or nonstandard default settings
of gcc"
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, efi: Don't use (U)EFI time services on 32 bit
x86, build, icc: Remove uninitialized_var() from compiler-intel.h
x86/UV: Fix NULL pointer dereference in uv_flush_tlb_others() if the 'nobau' boot option is used
x86, build: Pass in additional -mno-mmx, -mno-sse options
Pull SELinux fixes from James Morris.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
selinux: process labeled IPsec TCP SYN-ACK packets properly in selinux_ip_postroute()
selinux: look for IPsec labels on both inbound and outbound packets
selinux: handle TCP SYN-ACK packets correctly in selinux_ip_postroute()
selinux: handle TCP SYN-ACK packets correctly in selinux_ip_output()
selinux: fix possible memory leak
This reverts commit 102aefdda4.
Tom London reports that it causes sync() to hang on Fedora rawhide:
https://bugzilla.redhat.com/show_bug.cgi?id=1033965
and Josh Boyer bisected it down to this commit. Reverting the commit in
the rawhide kernel fixes the problem.
Eric Paris root-caused it to incorrect subtype matching in that commit
breaking fuse, and has a tentative patch, but by now we're better off
retrying this in 3.14 rather than playing with it any more.
Reported-by: Tom London <selinux@gmail.com>
Bisected-by: Josh Boyer <jwboyer@fedoraproject.org>
Acked-by: Eric Paris <eparis@redhat.com>
Cc: James Morris <jmorris@namei.org>
Cc: Anand Avati <avati@redhat.com>
Cc: Paul Moore <paul@paul-moore.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch changes the igb_phy_has_link function to check the value of the
parameter before deciding to use udelay or mdelay in order to be sure that
the value is not too high for udelay function.
CC: stable kernel <stable@vger.kernel.org> # 3.9+
Signed-off-by: Sunil K Pandey <sunil.k.pandey@intel.com>
Signed-off-by: Kevin B Smith <kevin.b.smith@intel.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the vsi->tx_rings structure is NULL we don't want to panic.
Change-Id: Ic694f043701738c434e8ebe0caf0673f4410dc10
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull ARM fixes from Russell King:
"This resolves some further issues with the dma mask changes on ARM
which have been found by TI and others, and also some corner cases
with the updates to the virtual to physical address translations.
Konstantin also found some problems with the unwinder, which now
performs tighter verification that the stack is valid while unwinding"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: fix asm/memory.h build error
ARM: 7917/1: cacheflush: correctly limit range of memory region being flushed
ARM: 7913/1: fix framepointer check in unwind_frame
ARM: 7912/1: check stack pointer in get_wchan
ARM: 7909/1: mm: Call setup_dma_zone() post early_paging_init()
ARM: 7908/1: mm: Fix the arm_dma_limit calculation
ARM: another fix for the DMA mapping checks
- Couple of fixes for recently added perf code
- Build time extable sort
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=JA1e
-----END PGP SIGNATURE-----
Merge tag 'arc-fixes-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"These are couple of weeks old already, but I just couldn't get them to
you earlier.
- couple of fixes for recently added perf code
- build time extable sort"
* tag 'arc-fixes-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: [perf] Fix a few thinkos
ARC: Add guard macro to uapi/asm/unistd.h
ARC: extable: Enable sorting at build time
A fix for possible memory corruption during DM table load, fix a
possible leak of snapshot space in case of a crash, fix a possible
deadlock due to a shared workqueue in the delay target, fix to
initialize read-only module parameters that are used to export metrics
for dm stats and dm bufio.
Quite a few stable fixes were identified for both the thin-provisioning
and caching targets as a result of increased regression testing using
the device-mapper-test-suite (dmts). The most notable of these are the
reference counting fixes for the space map btree that is used by the
dm-array interface -- without these the dm-cache metadata will leak,
resulting in dm-cache devices running out of metadata blocks. Also,
some important fixes related to the thin-provisioning target's
transition to read-only mode on error.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSq2pVAAoJEMUj8QotnQNaAzEH/0qpz06SVd3+oTbsWeWxXwax
B0zIZ4HPnaD9FDfSWN+6IdQ6Rkn51cspMBHPxWX0I8pmqOTg7MUM7wbaZZaKT3UW
aDlibzG1O3zBGbkr+Qhbh89fJK5/3xnZXlK0hOyaNI2vz1rA6RThZ2hIeak9xQYr
7USz2bjSMXchwebb0Z01CrRnOkhUFg6yUJURIEu4XFCJmDM/PM9zKogLGYKuZedK
pZePnZhwgkLMn7f9l4lPHk3EcWeD4Nf9WR0lS4eKdbYsvMxm1QE7BpDlVJD0Asjg
/SVOVkgygW18TINMHuw1K0DPdSCo5UZF2HRj1QUD/X4N2BSkio+E1qwF6kT4ltk=
=0Ix+
-----END PGP SIGNATURE-----
Merge tag 'dm-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
"A set of device-mapper fixes for 3.13.
A fix for possible memory corruption during DM table load, fix a
possible leak of snapshot space in case of a crash, fix a possible
deadlock due to a shared workqueue in the delay target, fix to
initialize read-only module parameters that are used to export metrics
for dm stats and dm bufio.
Quite a few stable fixes were identified for both the thin-
provisioning and caching targets as a result of increased regression
testing using the device-mapper-test-suite (dmts). The most notable
of these are the reference counting fixes for the space map btree that
is used by the dm-array interface -- without these the dm-cache
metadata will leak, resulting in dm-cache devices running out of
metadata blocks. Also, some important fixes related to the
thin-provisioning target's transition to read-only mode on error"
* tag 'dm-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm array: fix a reference counting bug in shadow_ablock
dm space map: disallow decrementing a reference count below zero
dm stats: initialize read-only module parameter
dm bufio: initialize read-only module parameters
dm cache: actually resize cache
dm cache: update Documentation for invalidate_cblocks's range syntax
dm cache policy mq: fix promotions to occur as expected
dm thin: allow pool in read-only mode to transition to read-write mode
dm thin: re-establish read-only state when switching to fail mode
dm thin: always fallback the pool mode if commit fails
dm thin: switch to read-only mode if metadata space is exhausted
dm thin: switch to read only mode if a mapping insert fails
dm space map metadata: return on failure in sm_metadata_new_block
dm table: fail dm_table_create on dm_round_up overflow
dm snapshot: avoid snapshot space leak on crash
dm delay: fix a possible deadlock due to shared workqueue
Jason Gunthorpe reports a build failure when ARM_PATCH_PHYS_VIRT is
not defined:
In file included from arch/arm/include/asm/page.h:163:0,
from include/linux/mm_types.h:16,
from include/linux/sched.h:24,
from arch/arm/kernel/asm-offsets.c:13:
arch/arm/include/asm/memory.h: In function '__virt_to_phys':
arch/arm/include/asm/memory.h:244:40: error: 'PHYS_OFFSET' undeclared (first use in this function)
arch/arm/include/asm/memory.h:244:40: note: each undeclared identifier is reported only once for each function it appears in
arch/arm/include/asm/memory.h: In function '__phys_to_virt':
arch/arm/include/asm/memory.h:249:13: error: 'PHYS_OFFSET' undeclared (first use in this function)
Fixes: ca5a45c06c ("ARM: mm: use phys_addr_t appropriately in p2v and v2p conversions")
Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A small set of driver fixes plus one larger core change which changes
the way we check to see if we're using DT so that there aren't any races
between deciding we're using DT and the regulator subsystem noticing.
This makes the new support for substituting a dummy regulator and
optional regulators work a lot better on DT systems since it ensures
that we don't trigger probe deferral when we shouldn't which was causing
bugs in clients.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=WqDN
-----END PGP SIGNATURE-----
Merge tag 'regulator-v3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A small set of driver fixes plus one larger core change which changes
the way we check to see if we're using DT so that there aren't any
races between deciding we're using DT and the regulator subsystem
noticing.
This makes the new support for substituting a dummy regulator and
optional regulators work a lot better on DT systems since it ensures
that we don't trigger probe deferral when we shouldn't which was
causing bugs in clients"
* tag 'regulator-v3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: pfuze100: allow misprogrammed ID
regulator: pfuze100: Fix address of FABID
regulator: as3722: set the correct current limit
regulator: core: Check for DT every time we check full constraints
regulator: core: Replace checks of have_full_constraints with a function
Two small changes to fix some error handling and checking (both of which
would be quite serious if the errors trigger) plus a trivial
documentation fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=YKD0
-----END PGP SIGNATURE-----
Merge tag 'regmap-v3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"Two small changes to fix some error handling and checking (both of
which would be quite serious if the errors trigger) plus a trivial
documentation fix"
* tag 'regmap-v3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: use IS_ERR() to check clk_get() results
regmap: make sure we unlock on failure in regmap_bulk_write
regmap: trivial comment fix (copy'n'paste error)
Pull i2c fixes from Wolfram Sang:
"Here are two simple but wanted fixes for the i2c subsystem"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: imx: Check the return value from clk_prepare_enable()
i2c: mux: Inherit retry count and timeout from parent for muxed bus
- This driver was not ready to fully Armada 370 NAND, with particularly
notable problems seen on flash with 2KB page sizes. This "compatible" entry
really should have been held back until 3.14 or later.
- Fix a bug seen in rare cases on the error path of a failed probe attempt,
where we free unallocated DMA resources
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=K24+
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20131212' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
"Two MTD fixes, for the pxa3xx-nand driver:
- This driver was not ready to fully Armada 370 NAND, with
particularly notable problems seen on flash with 2KB page sizes.
This "compatible" entry really should have been held back until
3.14 or later.
- Fix a bug seen in rare cases on the error path of a failed probe
attempt, where we free unallocated DMA resources"
* tag 'for-linus-20131212' of git://git.infradead.org/linux-mtd:
mtd: nand: pxa3xx: Use info->use_dma to release DMA resources
Partially revert "mtd: nand: pxa3xx: Introduce 'marvell,armada370-nand' compatible string"
Pull slave-dmaengine fixes from Vinod Koul:
"Here is the common fixes PULL for dmaengine.
Dan has been working on fixing the build issues in bunch of drivers.
Here we have one fixing s3c24xx-dma, along with fix from Russell on
pl08x. Also we have Kuninori rcar dma fixes. The s3c24xx-dma which
was added in last merge window missed updates to usage of DMA_COMPLETE
so converting the last driver"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dma: fix build breakage in s3c24xx-dma
Fix pl08x warnings
rcar-hpbdma: initialise plane information when halted
rcar-hpbdma: fixup channel busy check for double plane
rcar-hpbdma: add max transfer size
dma: mmp_pdma: add missing platform_set_drvdata() in mmp_pdma_probe()
dmaengine: s3c24xx-dma: use DMA_COMPLETE for dma completion status
An old array block could have its reference count decremented below
zero when it is being replaced in the btree by a new array block.
The fix is to increment the old ablock's reference count just before
inserting a new ablock into the btree.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.9+
The old behaviour, returning -EINVAL if a ref_count of 0 would be
decremented, was removed in commit f722063 ("dm space map: optimise
sm_ll_dec and sm_ll_inc"). To fix this regression we return an error
code from the mutator function pointer passed to sm_ll_mutate() and have
dec_ref_count() return -EINVAL if the old ref_count is 0.
Add a DMERR to reflect the potential seriousness of this error.
Also, add missing dm_tm_unlock() to sm_ll_mutate()'s error path.
With this fix the following dmts regression test now passes:
dmtest run --suite cache -n /metadata_use_kernel/
The next patch fixes the higher-level dm-array code that exposed this
regression.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.12+
Merge patches from Andrew Morton:
"13 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: memcg: do not allow task about to OOM kill to bypass the limit
mm: memcg: fix race condition between memcg teardown and swapin
thp: move preallocated PTE page table on move_huge_pmd()
mfd/rtc: s5m: fix register updating by adding regmap for RTC
rtc: s5m: enable IRQ wake during suspend
rtc: s5m: limit endless loop waiting for register update
rtc: s5m: fix unsuccesful IRQ request during probe
drivers/rtc/rtc-s5m.c: fix info->rtc assignment
include/linux/kernel.h: make might_fault() a nop for !MMU
drivers/rtc/rtc-at91rm9200.c: correct alarm over day/month wrap
procfs: also fix proc_reg_get_unmapped_area() for !MMU case
mm: memcg: do not declare OOM from __GFP_NOFAIL allocations
include/linux/hugetlb.h: make isolate_huge_page() an inline
Commit 4942642080 ("mm: memcg: handle non-error OOM situations more
gracefully") allowed tasks that already entered a memcg OOM condition to
bypass the memcg limit on subsequent allocation attempts hoping this
would expedite finishing the page fault and executing the kill.
David Rientjes is worried that this breaks memcg isolation guarantees
and since there is no evidence that the bypass actually speeds up fault
processing just change it so that these subsequent charge attempts fail
outright. The notable exception being __GFP_NOFAIL charges which are
required to bypass the limit regardless.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reported-by: David Rientjes <rientjes@google.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Acked-bt: David Rientjes <rientjes@google.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a race condition between a memcg being torn down and a swapin
triggered from a different memcg of a page that was recorded to belong
to the exiting memcg on swapout (with CONFIG_MEMCG_SWAP extension). The
result is unreclaimable pages pointing to dead memcgs, which can lead to
anything from endless loops in later memcg teardown (the page is charged
to all hierarchical parents but is not on any LRU list) or crashes from
following the dangling memcg pointer.
Memcgs with tasks in them can not be torn down and usually charges don't
show up in memcgs without tasks. Swapin with the CONFIG_MEMCG_SWAP
extension is the notable exception because it charges the cgroup that
was recorded as owner during swapout, which may be empty and in the
process of being torn down when a task in another memcg triggers the
swapin:
teardown: swapin:
lookup_swap_cgroup_id()
rcu_read_lock()
mem_cgroup_lookup()
css_tryget()
rcu_read_unlock()
disable css_tryget()
call_rcu()
offline_css()
reparent_charges()
res_counter_charge() (hierarchical!)
css_put()
css_free()
pc->mem_cgroup = dead memcg
add page to dead lru
Add a final reparenting step into css_free() to make sure any such raced
charges are moved out of the memcg before it's finally freed.
In the longer term it would be cleaner to have the css_tryget() and the
res_counter charge under the same RCU lock section so that the charge
reparenting is deferred until the last charge whose tryget succeeded is
visible. But this will require more invasive changes that will be
harder to evaluate and backport into stable, so better defer them to a
separate change set.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: David Rientjes <rientjes@google.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Wagin reported crash on VM_BUG_ON() in pgtable_pmd_page_dtor() with
fallowing backtrace:
free_pgd_range+0x2bf/0x410
free_pgtables+0xce/0x120
unmap_region+0xe0/0x120
do_munmap+0x249/0x360
move_vma+0x144/0x270
SyS_mremap+0x3b9/0x510
system_call_fastpath+0x16/0x1b
The crash can be reproduce with this test case:
#define _GNU_SOURCE
#include <sys/mman.h>
#include <stdio.h>
#include <unistd.h>
#define MB (1024 * 1024UL)
#define GB (1024 * MB)
int main(int argc, char **argv)
{
char *p;
int i;
p = mmap((void *) GB, 10 * MB, PROT_READ | PROT_WRITE,
MAP_PRIVATE | MAP_ANONYMOUS | MAP_FIXED, -1, 0);
for (i = 0; i < 10 * MB; i += 4096)
p[i] = 1;
mremap(p, 10 * MB, 10 * MB, MREMAP_FIXED | MREMAP_MAYMOVE, 2 * GB);
return 0;
}
Due to split PMD lock, we now store preallocated PTE tables for THP
pages per-PMD table. It means we need to move them to other PMD table
if huge PMD moved there.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Andrey Vagin <avagin@openvz.org>
Tested-by: Andrey Vagin <avagin@openvz.org>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename old regmap field of "struct sec_pmic_dev" to "regmap_pmic" and
add new regmap for RTC.
On S5M8767A registers were not properly updated and read due to usage of
the same regmap as the PMIC. This could be observed in various hangs,
e.g. in infinite loop during waiting for UDR field change.
On this chip family the RTC has different I2C address than PMIC so
additional regmap is needed.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add PM suspend/resume ops to rtc-s5m driver and enable IRQ wake during
suspend so the RTC would act like a wake up source. This allows waking
up from suspend to RAM on RTC alarm interrupt.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Mark Brown <broonie@linaro.org>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After setting alarm or time the driver is waiting for UDR register to be
cleared indicating that registers data have been transferred.
Limit the endless loop to only 5 retries.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Probe failed for rtc-s5m:
s5m-rtc s5m-rtc: Failed to request alarm IRQ: 12: -22
s5m-rtc: probe of s5m-rtc failed with error -22
Fix rtc-s5m interrupt request by using regmap_irq_get_virq() for mapping
the IRQ.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix this warning:
drivers/rtc/rtc-s5m.c: In function `s5m_rtc_probe':
drivers/rtc/rtc-s5m.c:545: warning: assignment from incompatible pointer type
struct s5m_rtc_info.rtc has type "struct regmap *", while
struct sec_pmic_dev.rtc has type "struct i2c_client *".
Probably the author wanted to assign "struct sec_pmic_dev.regmap", which
has the correct type.
Also, as "rtc" doesn't make much sense as a name for a regmap, rename it
to "regmap".
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Sachin Kamat <sachin.kamat@linaro.org>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The machine cannot fault if !MUU, so make might_fault() a nop for !MMU.
This fixes below build error if
!CONFIG_MMU && (CONFIG_PROVE_LOCKING=y || CONFIG_DEBUG_ATOMIC_SLEEP=y):
arch/arm/kernel/built-in.o: In function `arch_ptrace':
arch/arm/kernel/ptrace.c:852: undefined reference to `might_fault'
arch/arm/kernel/built-in.o: In function `restore_sigframe':
arch/arm/kernel/signal.c:173: undefined reference to `might_fault'
...
arch/arm/kernel/built-in.o:arch/arm/kernel/signal.c:177: more undefined references to `might_fault' follow
make: *** [vmlinux] Error 1
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update month and day of month to the alarm month/day instead of current
day/month when setting the RTC alarm mask.
Signed-off-by: Linus Pizunski <linus@narrativeteam.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit fad1a86e25 ("procfs: call default get_unmapped_area on
MMU-present architectures"), as its title says, took care of only the
MMU case, leaving the !MMU side still in the regressed state (returning
-EIO in all cases where pde->proc_fops->get_unmapped_area is NULL).
From the fad1a86e25 changelog:
"Commit c4fe244857 ("sparc: fix PCI device proc file mmap(2)") added
proc_reg_get_unmapped_area in proc_reg_file_ops and
proc_reg_file_ops_no_compat, by which now mmap always returns EIO if
get_unmapped_area method is not defined for the target procfs file, which
causes regression of mmap on /proc/vmcore.
To address this issue, like get_unmapped_area(), call default
current->mm->get_unmapped_area on MMU-present architectures if
pde->proc_fops->get_unmapped_area, i.e. the one in actual file operation
in the procfs file, is not defined"
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: <stable@vger.kernel.org> [3.12.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 84235de394 ("fs: buffer: move allocation failure loop into the
allocator") started recognizing __GFP_NOFAIL in memory cgroups but
forgot to disable the OOM killer.
Any task that does not fail allocation will also not enter the OOM
completion path. So don't declare an OOM state in this case or it'll be
leaked and the task be able to bypass the limit until the next
userspace-triggered page fault cleans up the OOM state.
Reported-by: William Dauchy <wdauchy@gmail.com>
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: David Rientjes <rientjes@google.com>
Cc: <stable@vger.kernel.org> [3.12.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
from Google for reporting them.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=auYv
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"Four security fixes for KVM on x86. Thanks to Andrew Honig and Lars
Bull from Google for reporting them"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: fix guest-initiated crash with x2apic (CVE-2013-6376)
KVM: x86: Convert vapic synchronization to _cached functions (CVE-2013-6368)
KVM: x86: Fix potential divide by 0 in lapic (CVE-2013-6367)
KVM: Improve create VCPU parameter (CVE-2013-4587)
Another week, another batch of fixes.
Again, OMAP regressions due to move to DT is the bulk of the changes here,
but this should be the last of it for 3.13. There are also a handful of
OMAP hwmod changes (power management, reset handling) for USB on OMAP3
that fixes some longish-standing bugs around USB resets.
There are a couple of other changes that also add up line count a bit:
One is a long-standing bug with the keyboard layout on one of the
PXA platforms. The other is a fix for highbank that moves their
power-off/reset button handling to be done in-kernel since relying on
userspace to handle it was fragile and awkward.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJSqRaIAAoJEIwa5zzehBx36e0P/35YmpsILX1FR1MvAv2DjB1m
cRrUrdGI2hPkT7aIE35QPJF3GEvNm//4hHOK/r9+BkQSRecDmJaY6E6NvEo4mPRz
at+R9JpddInbthMc1AylnlRJOxl5TbFFx0MJr/cXB8KAXN0iYu9h3brZyDHz7Wkg
3hqQ+4ZuQwXQmmNJEftPxnXCQAZLiU3hSMYPCmJ71YEB9oKBJoNsJNsMNDRQWu/d
VCYbGlnzCuVaOvHm0/KHUQHKOS2K28vT9goCyh3f+Vbt5n4HNb6SicXTo2f3pY30
N1ThifxRuGEYhQMzlq6AWnFaLkDqivBq6V2P0tG+JJOY1Z4HkqGsAr2SDylOkTy0
rqMCRA12PPw79W57LwMT8Fzokuq5CLBT+sahqUuuV4l7C9Sdnzr8ZbQn7s2YeW52
lqG4rk+t2muMdqHmTmglb86nMiBr6raOLwDGVt8Ttgnryjl/au64FoZx7UsWMEDg
/ppkKvAmeL+f8Fde+JQTFpJdxaUHKc/NgjHYFxpt8Ef46CRiOcCAh08VD2oUWjso
JKwb03axdHaJVgFm/KKwQ8uoNG0ouxkw9aCLjkrMYda7MRCpBAYPdQPBaMXziaAU
acjouVrxxNfKLH2h3+brmFhMO5yUZYUbQs4BOi+Z0w1BJLxouEMrJ97ZxeFxBRug
J4i4tk7d//YDriS5HoYx
=WRn8
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another week, another batch of fixes.
Again, OMAP regressions due to move to DT is the bulk of the changes
here, but this should be the last of it for 3.13. There are also a
handful of OMAP hwmod changes (power management, reset handling) for
USB on OMAP3 that fixes some longish-standing bugs around USB resets.
There are a couple of other changes that also add up line count a bit:
One is a long-standing bug with the keyboard layout on one of the PXA
platforms. The other is a fix for highbank that moves their
power-off/reset button handling to be done in-kernel since relying on
userspace to handle it was fragile and awkward"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: sun6i: dt: Fix interrupt trigger types
ARM: sun7i: dt: Fix interrupt trigger types
MAINTAINERS: merge IMX6 entry into IMX
ARM: tegra: add missing break to fuse initialization code
ARM: pxa: prevent PXA270 occasional reboot freezes
ARM: pxa: tosa: fix keys mapping
ARM: OMAP2+: omap_device: add fail hook for runtime_pm when bad data is detected
ARM: OMAP2+: hwmod: Fix usage of invalid iclk / oclk when clock node is not present
ARM: OMAP3: hwmod data: Don't prevent RESET of USB Host module
ARM: OMAP2+: hwmod: Fix SOFTRESET logic
ARM: OMAP4+: hwmod data: Don't prevent RESET of USB Host module
ARM: dts: Fix booting for secure omaps
ARM: OMAP2+: Fix the machine entry for am3517
ARM: dts: Fix missing entries for am3517
ARM: OMAP2+: Fix overwriting hwmod data with data from device tree
ARM: davinci: Fix McASP mem resource names
ARM: highbank: handle soft poweroff and reset key events
ARM: davinci: fix number of resources passed to davinci_gpio_register()
gpio: davinci: fix check for unbanked gpio
Pull btrfs fixes from Chris Mason:
"This is a small collection of fixes. It was rebased this morning, but
I was just fixing signed-off-by tags with the wrong email"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix access_ok() check in btrfs_ioctl_send()
Btrfs: make sure we cleanup all reloc roots if error happens
Btrfs: skip building backref tree for uuid and quota tree when doing balance relocation
Btrfs: fix an oops when doing balance relocation
Btrfs: don't miss skinny extent items on delayed ref head contention
btrfs: call mnt_drop_write after interrupted subvol deletion
Btrfs: don't clear the default compression type
Pull nfsd reply cache bugfix from Bruce Fields:
"One bugfix for nfsd crashes"
* 'for-3.13' of git://linux-nfs.org/~bfields/linux:
nfsd: when reusing an existing repcache entry, unhash it first
In commit:
commit 62e8b85178
Author: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Date: Fri Oct 4 15:30:38 2013 -0300
mtd: nand: pxa3xx: Allocate data buffer on detected flash size
the way the buffer is allocated was changed: the first READ_ID is issued
with a small kmalloc'ed buffer. Only once the flash page size is detected
the DMA buffers are allocated, and info->use_dma is set.
Currently, if the device detection fails, the driver checks the 'use_dma'
module parameter and tries to release unallocated DMA resources.
Fix this by checking the proper indicator of the DMA allocation, which
is 'info->use_dma'.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
