To instatiate pre-configured vport entities defined within an
HBA's flash memory.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The Flash Layout Table (FLT) present on many recent HBAs encodes
flash usage information, organizes data stored into separate
regions and presents the information uniformly to the driver.
Use this information rather than using specific hard-coded values
based on ISP type.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Both call-sites are sleeping-capable.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Currently Firmware does not have counters for input megabytes and
output megabytes, therefore driver counts these values depending
on the status of the scsi command and direction of the command.
The values are exported in the FC_HOST path.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Due to patch building error on my side, we are still passing DID_BUS_BUSY
for commands that are running, when we want to return whatever the caller
of fail_all_commands wanted. This replaces the hardcoded error code with
the value that is passed in.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There's already a fc_vport_termintate() call exported by
the transport. This patch adds a symmetric call to the API to allow
an NPIV-capable LLD to instantiate vports sans user intervention.
Additional comments/updates:
Re: scsi_fc_transport.txt
Add a function prototype for fc_vport_terminate similar to what's
done for fc_vport_create
Re: fc_vport_create
I recommend we pass the channel number in fc_vport_create rather
than fixing it at zero.
Also, ids->vport_type should be set to FC_PORTTYPE_NPIV prior to
calling fc_vport_create. The comment is also meaningless.
Added-by and
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch adds the ability to print sizes in either units of 10^3 (SI)
or 2^10 (Binary) units. It rounds up to three significant figures and
can be used for either memory or storage capacities.
Oh, and I'm fully aware that 64 bits is only 16EiB ... the Zetta and
Yotta units are added for future proofing against the day we have 128
bit computers ...
[fujita.tomonori@lab.ntt.co.jp: fix missed unsigned long long cast]
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
blk_get_request initializes rq->cmd (rq_init does) so the users don't
need to do that.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Brian King <brking@linux.vnet.ibm.com> reported that fibre channel
devices can oops during scanning if their ports block (because the
device goes from CREATED -> BLOCK -> RUNNING rather than CREATED ->
BLOCK -> CREATED).
Fix this by adding a new state: CREATED_BLOCK which can only transition
back to CREATED and disallow the CREATED -> BLOCK transition. Now both
the created and blocked states that the mid-layer recognises can include
CREATED_BLOCK.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The created and blocked states are very shortly going to correspond to
mixed sdev_state states.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch adds scsi netlink recieve and event support for transport
and scsi LLDD's. It is a reimplementation of the patch posted last
week by David Somayajulu.
http://marc.info/?l=linux-scsi&m=121745486221819&w=2
There are a few things done differently:
- Transport support is included
- Event delivery is included
- The vendor message is now its own unique message type, considered
part of the generic "SCSI Transport".
- LLDD entry points are now registered rather than included in the
scsi_host_template.
Background: When I started to implement the event handler via template,
I had to either: muck up scsi_add_host and scsi_remove_host; or have
the event handler search all possible shosts. Neither was acceptable.
Moving to a registration solves this, and also limits the scope of
the changes to something that could be backported to a distro without
breaking an already-released-distro kabi. However, I admit it isn't
as elegant, as the passing of the LLDD host template in the
registration and the complexity around dynamic add/remove shows.
- The receive path was augmented to require a unique identifier for
the LLDD before the message was allowed to be handed off to the
driver. Given how quickly very fatal errors occur if there's msg
mismatches (which I saw in testing my own tools :), I believe this
to be a very good thing. The id plays off the vendor id scheme already
introduced for the vendor unique event messages used by FC.
Additionally, the id use as the basis of the registration/deregistration.
- Send assist functions, for both the transport and LLDDs are included.
[fujita.tomonori@lab.ntt.co.jp: fix missing cast]
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Multiline kernel messages should contain a priority in every line,
besides, some log daemons represent a tabulator as "^I", fix both these
issues.
Signed-off-by: Nick Warne <nick@ukfsn.org>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Now that qla2xxx has been converted to mutexes, it no longer needs the
semaphore include.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch cleans up the behavior of scsi_host_lookup().
The original implementation attempted to use the dual role of
either returning a pointer value, or a negative error code.
User's needed to use IS_ERR() to check the result. Additionally,
the IS_ERR() macro never checks for when a NULL pointer was
returned, so a NULL pointer actually passes with a success case.
Note: scsi_host_get(), used by scsi_host_lookup(), can return
a NULL pointer.
Talk about a mudhole for the unitiated to step into....
This patch converts scsi_host_lookup() to return either NULL
or a valid pointer. The consumers were updated for the change.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch adds a mutex to the e1000e driver that would help
catch any collisions of two e1000e threads accessing hardware
at the same time.
description and patch updated by Jesse
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
the stats lock is left over from e1000, e1000e no longer
has the adjust tbi stats function that required the addition
of the stats lock to begin with.
adding a mutex to acquire_swflag helped catch this one too.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
thanks to tglx, we're finding some interesting reentrancy issues.
this patch removes the phy read from inside a spinlock, paving
the way for removing the spinlock completely. The phy read was
only feeding a statistic that wasn't used.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
e1000e was apparently calling two functions that attempted to reserve
the SWFLAG bit for exclusive (to hardware and firmware) access to
the PHY and NVM (aka eeprom). These accesses could possibly call
msleep to wait for the resource which is not allowed from interrupt
context.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
in the process of debugging things, noticed that the swflag is not reset
by the driver after reset, and the swflag is probably not reset unless
management firmware clears it after 100ms.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When we initialise a compound page we initialise the page flags and head
page pointer for all base pages spanned by that page. When we initialise
a gigantic page (a page of order greater than or equal to MAX_ORDER) we
have to initialise more than MAX_ORDER_NR_PAGES pages. Currently we
assume that all elements of the mem_map in this page are contigious in
memory. However this is only guarenteed out to MAX_ORDER_NR_PAGES pages,
and with SPARSEMEM enabled they will not be contigious. This leads us to
walk off the end of the first section and scribble on everything which
follows, BAD.
When we reach a MAX_ORDER_NR_PAGES boundary we much locate the next
section of the mem_map. As gigantic pages can only be maximally aligned
we know this will occur at exact multiple of MAX_ORDER_NR_PAGES pages from
the start of the page.
This is a bug fix for the gigantic page support in hugetlbfs.
Credit to Mel Gorman for spotting the issue.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Jon Tollefson <kniht@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The previous patch db203d53d4 ("mm:
tiny-shmem fix lock ordering: mmap_sem vs i_mutex") to fix the lock
ordering in tiny-shmem breaks shared anonymous and IPC memory on NOMMU
architectures because it was using the expanding truncate to signal ramfs
to allocate a physically contiguous RAM backing the inode (otherwise it is
unusable for "memory mapping" it to userspace).
However do_truncate is what caused the lock ordering error, due to it
taking i_mutex. In this case, we can actually just call ramfs directly to
allocate memory for the mapping, rather than go via truncate.
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__test_page_isolated_in_pageblock() in mm/page_isolation.c has a comment
saying that the caller must hold zone->lock. But the only caller of that
function, test_pages_isolated(), does not hold zone->lock and the lock is
also not acquired anywhere before. This patch adds the missing zone->lock
to test_pages_isolated().
We reproducibly run into BUG_ON(!PageBuddy(page)) in __offline_isolated_pages()
during memory hotplug stress test, see trace below. This patch fixes that
problem, it would be good if we could have it in 2.6.27.
kernel BUG at /home/autobuild/BUILD/linux-2.6.26-20080909/mm/page_alloc.c:4561!
illegal operation: 0001 [#1] PREEMPT SMP
Modules linked in: dm_multipath sunrpc bonding qeth_l3 dm_mod qeth ccwgroup vmur
CPU: 1 Not tainted 2.6.26-29.x.20080909-s390default #1
Process memory_loop_all (pid: 10025, task: 2f444028, ksp: 2b10dd28)
Krnl PSW : 040c0000 801727ea (__offline_isolated_pages+0x18e/0x1c4)
R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:0 CC:0 PM:0
Krnl GPRS: 00000000 7e27fc00 00000000 7e27fc00
00000000 00000400 00014000 7e27fc01
00606f00 7e27fc00 00013fe0 2b10dd28
00000005 80172662 801727b2 2b10dd28
Krnl Code: 801727de: 5810900c l %r1,12(%r9)
801727e2: a7f4ffb3 brc 15,80172748
801727e6: a7f40001 brc 15,801727e8
>801727ea: a7f4ffbc brc 15,80172762
801727ee: a7f40001 brc 15,801727f0
801727f2: a7f4ffaf brc 15,80172750
801727f6: 0707 bcr 0,%r7
801727f8: 0017 unknown
Call Trace:
([<0000000000172772>] __offline_isolated_pages+0x116/0x1c4)
[<00000000001953a2>] offline_isolated_pages_cb+0x22/0x34
[<000000000013164c>] walk_memory_resource+0xcc/0x11c
[<000000000019520e>] offline_pages+0x36a/0x498
[<00000000001004d6>] remove_memory+0x36/0x44
[<000000000028fb06>] memory_block_change_state+0x112/0x150
[<000000000028ffb8>] store_mem_state+0x90/0xe4
[<0000000000289c00>] sysdev_store+0x34/0x40
[<00000000001ee048>] sysfs_write_file+0xd0/0x178
[<000000000019b1a8>] vfs_write+0x74/0x118
[<000000000019b9ae>] sys_write+0x46/0x7c
[<000000000011160e>] sysc_do_restart+0x12/0x16
[<0000000077f3e8ca>] 0x77f3e8ca
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Found by static checker (http://repo.or.cz/w/smatch.git).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Only register the braille driver VT and keyboard notifiers when the
braille console is used. Avoids eating insert or backspace keys.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11242
Signed-off-by: Pascal Terjan <pterjan@mandriva.com>
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 22af89aa0c ("fbcon: replace mono_col
macro with static inline") changed the order of operations for computing
monochrome color values. This generates 0xffff000f instead of 0x0000000f
for a 4 bit monochrome color, leading to image corruption if it is passed
to cfb_imageblit or other similar functions. Fix it up.
Cc: Harvey Harrison <harvey.harrison@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: <stable@kernel.org> [2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: snd-powermac: HP detection for 1st iMac G3 SL
ALSA: snd-powermac: mixers for PowerMac G4 AGP
ASoC: Set correct name for WM8753 rec mixer output
Correct headphone detection for 1st generation iMac G3 Slot-loading (Screamer).
This patch fixes the regression in the recent snd-powermac which
doesn't support some G3/G4 PowerMacs:
http://lkml.org/lkml/2008/10/1/220
Signed-off-by: Risto Suominen <Risto.Suominen@gmail.com>
Tested-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add mixer controls for PowerMac G4 AGP (Screamer).
This patch fixes the regression in the recent snd-powermac which
doesn't support some G3/G4 PowerMacs:
http://lkml.org/lkml/2008/10/1/220
Signed-off-by: Risto Suominen <Risto.Suominen@gmail.com>
Tested-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rob Sims wrote:
"I can't seem to turn on register 0x17, bit 3 in the sound chip, except
by codec_reg_write; the mixer lacks direct or indirect control. It
seems there are two names for the output of the rec mixer:
Capture ST Mixer
Playback Mixer
Would the following do the trick?"
I confirm that this solves the audio problems I was having.
Signed-off-by: Jonas Bonn <jonas.bonn@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 00c5372d37 caused the MPC8544DS
board to hang at boot. The MPC8544DS is unique in that it doesn't use
the PCI slots on the ULI (unlike the MPC8572DS or MPC8610HPCD). So
the dummy read at the end of the address space causes us to hang.
We can detect the situation by comparing the bridge's BARs versus
the root complex.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Set the hardware to ignore all write/erase cycles to the GbE region in
the ICHx NVM. This feature can be disabled by the WriteProtectNVM module
parameter (enabled by default) only after a hardware reset, but
the machine must be power cycled before trying to enable writes.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: arjan@linux.intel.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a build error in the pxa2xx-spi driver,
introduced by commit 7e96445533
("pxa2xx_spi: dma bugfixes")
CC drivers/spi/pxa2xx_spi.o
drivers/spi/pxa2xx_spi.c: In function 'map_dma_buffers':
drivers/spi/pxa2xx_spi.c:331: error: invalid operands to binary &
drivers/spi/pxa2xx_spi.c:331: error: invalid operands to binary &
drivers/spi/pxa2xx_spi.c: In function 'pump_transfers':
drivers/spi/pxa2xx_spi.c:897: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'unsigned int'
[dbrownell@users.sourceforge.net: fix warning too ]
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the IRQ handling on the MN10300 arch.
This patch makes a number of significant changes:
(1) It separates the irq_chip definition for edge-triggered interrupts from
the one for level-triggered interrupts.
This is necessary because the MN10300 PIC latches the IRQ channel's
interrupt request bit (GxICR_REQUEST), even after the device has ceased to
assert its interrupt line and the interrupt channel has been disabled in
the PIC. So for level-triggered interrupts we need to clear this bit when
we re-enable - which is achieved by setting GxICR_DETECT but not
GxICR_REQUEST when writing to the register.
Not doing this results in spurious interrupts occurring because calling
mask_ack() at the start of handle_level_irq() is insufficient - it fails
to clear the REQUEST latch because the device that caused the interrupt is
still asserting its interrupt line at this point.
(2) IRQ disablement [irq_chip::disable_irq()] shouldn't clear the interrupt
request flag for edge-triggered interrupts lest it lose an interrupt.
(3) IRQ unmasking [irq_chip::unmask_irq()] also shouldn't clear the interrupt
request flag for edge-triggered interrupts lest it lose an interrupt.
(4) The end() operation is now left to the default (no-operation) as
__do_IRQ() is compiled out. This may affect misrouted_irq(), but
according to Thomas Gleixner it's the correct thing to do.
(5) handle_level_irq() is used for edge-triggered interrupts rather than
handle_edge_irq() as the MN10300 PIC latches interrupt events even on
masked IRQ channels, thus rendering IRQ_PENDING unnecessary. It is
sufficient to call mask_ack() at the start and unmask() at the end.
(6) For level-triggered interrupts, ack() is now NULL as it's not used, and
there is no effective ACK function on the PIC. mask_ack() is now the
same as mask() as the latch continues to latch, even when the channel is
masked.
Further, the patch discards the disable() op implementation as its now the same
as the mask() op implementation, which is used instead.
It also discards the enable() op implementations as they're now the same as
the unmask() op implementations, which are used instead.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm:
dm mpath: add missing path switching locking
dm: cope with access beyond end of device in dm_merge_bvec
dm: always allow one page in dm_merge_bvec
Moving the path activation to workqueue along with scsi_dh patches introduced
a race. It is due to the fact that the current_pgpath (in the multipath data
structure) can be modified if changes happen in any of the paths leading to
the lun. If the changes lead to current_pgpath being set to NULL, then it
leads to the invalid access which results in the panic below.
This patch fixes that by storing the pgpath to activate in the multipath data
structure and properly protecting it.
Note that if activate_path is called twice in succession with different pgpath,
with the second one being called before the first one is done, then activate
path will be called twice for the second pgpath, which is fine.
Unable to handle kernel paging request for data at address 0x00000020
Faulting instruction address: 0xd000000000aa1844
cpu 0x1: Vector: 300 (Data Access) at [c00000006b987a80]
pc: d000000000aa1844: .activate_path+0x30/0x218 [dm_multipath]
lr: c000000000087a2c: .run_workqueue+0x114/0x204
sp: c00000006b987d00
msr: 8000000000009032
dar: 20
dsisr: 40000000
current = 0xc0000000676bb3f0
paca = 0xc0000000006f3680
pid = 2528, comm = kmpath_handlerd
enter ? for help
[c00000006b987da0] c000000000087a2c .run_workqueue+0x114/0x204
[c00000006b987e40] c000000000088b58 .worker_thread+0x120/0x144
[c00000006b987f00] c00000000008ca70 .kthread+0x78/0xc4
[c00000006b987f90] c000000000027cc8 .kernel_thread+0x4c/0x68
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If for any reason dm_merge_bvec() is given an offset beyond the end of the
device, avoid an oops and always allow one page to be added to an empty bio.
We'll reject the I/O later after the bio is submitted.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Some callers assume they can always add at least one page to an empty bio,
so dm_merge_bvec should not return 0 in this case: we'll reject the I/O
later after the bio is submitted.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Fix a xfrm_{state,policy}_walk leak if pfkey socket is closed while
dumping is on-going.
Signed-off-by: Timo Teras <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following actions are possible:
tcp_v6_rcv
skb->dev = NULL;
tcp_v6_do_rcv
tcp_v6_hnd_req
tcp_check_req
req->rsk_ops->send_ack == tcp_v6_send_ack
So, skb->dev can be NULL in tcp_v6_send_ack. We must obtain namespace
from dst entry.
Thanks to Vitaliy Gusev <vgusev@openvz.org> for initial problem finding
in IPv4 code.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This one took a long time to rear up because LDT usage is not very
common, but the bug is quite serious. It got introduced along with
another bug, already fixed, by 75b8bb3e56
After investigating a JRE failure, I found this bug was introduced a long time
ago, and had already managed to survive another bugfix which occurred on the
same line. The result is a total failure of the JRE due to LDT selectors not
working properly.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: Glauber de Oliveira Costa <gcosta@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
After investigating a JRE failure, I found this bug was introduced a
long time ago, and had already managed to survive another bugfix which
occurred on the same line. The result is a total failure of the JRE due
to LDT selectors not working properly.
This one took a long time to rear up because LDT usage is not very
common, but the bug is quite serious. It got introduced along with
another bug, already fixed, by 75b8bb3e56
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Glauber de Oliveira Costa <gcosta@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
