Use kmemdup when some other buffer is immediately copied into allocated
region. It replaces call to allocation followed by memcpy, by a single
call to kmemdup.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current implementation updates the mtu size and notify cdc_ncm
device using USB_CDC_SET_MAX_DATAGRAM_SIZE request about datagram
size change instead of changing rx_urb_size.
Whenever mtu is being changed, datagram size should also be
updated. Also updating maxmtu formula so it takes max_datagram_size with
use of cdc_ncm_max_dgram_size() and not ctx.
Signed-off-by: Robert Dobrowolski <robert.dobrowolski@linux.intel.com>
Signed-off-by: Rafal Redzimski <rafal.f.redzimski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(!count || count < 4) is always true.
So let's remove the coding which is dead at least since 2005.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In testing with HiKey, we found that since
commit 3f30b158eb ("asix: On RX avoid creating bad Ethernet
frames"),
we're seeing lots of noise during network transfers:
[ 239.027993] asix 1-1.1:1.0 eth0: asix_rx_fixup() Data Header synchronisation was lost, remaining 988
[ 239.037310] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x54ebb5ec, offset 4
[ 239.045519] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0xcdffe7a2, offset 4
[ 239.275044] asix 1-1.1:1.0 eth0: asix_rx_fixup() Data Header synchronisation was lost, remaining 988
[ 239.284355] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x1d36f59d, offset 4
[ 239.292541] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0xaef3c1e9, offset 4
[ 239.518996] asix 1-1.1:1.0 eth0: asix_rx_fixup() Data Header synchronisation was lost, remaining 988
[ 239.528300] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x2881912, offset 4
[ 239.536413] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x5638f7e2, offset 4
And network throughput ends up being pretty bursty and slow with
a overall throughput of at best ~30kB/s (where as previously we
got 1.1MB/s with the slower USB1.1 "full speed" host).
We found the issue also was reproducible on a x86_64 system,
using a "high-speed" USB2.0 port but the throughput did not
measurably drop (possibly due to the scp transfer being cpu
bound on my slow test hardware).
After lots of debugging, I found the check added in the
problematic commit seems to be calculating the offset
incorrectly.
In the normal case, in the main loop of the function, we do:
(where offset is zero, or set to "offset += (copy_length + 1) &
0xfffe" in the previous loop)
rx->header = get_unaligned_le32(skb->data +
offset);
offset += sizeof(u32);
But the problematic patch calculates:
offset = ((rx->remaining + 1) & 0xfffe) + sizeof(u32);
rx->header = get_unaligned_le32(skb->data + offset);
Adding some debug logic to check those offset calculation used
to find rx->header, the one in problematic code is always too
large by sizeof(u32).
Thus, this patch removes the incorrect " + sizeof(u32)" addition
in the problematic calculation, and resolves the issue.
Cc: Dean Jenkins <Dean_Jenkins@mentor.com>
Cc: "David B. Robins" <linux@davidrobins.net>
Cc: Mark Craske <Mark_Craske@mentor.com>
Cc: Emil Goode <emilgoode@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: YongQin Liu <yongqin.liu@linaro.org>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Ivan Vecera <ivecera@redhat.com>
Cc: linux-usb@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: stable <stable@vger.kernel.org> #4.4+
Reported-by: Yongqin Liu <yongqin.liu@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the call to fn() fails then "buf" is uninitialized. Just return the
error code in that case.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the fn() calls fail then "buf" is uninitialized. Just return early
in that situation.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv4/ip_gre.c
Minor conflicts between tunnel bug fixes in net and
ipv6 tunnel cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
This takes the MAC address for smsc75xx/smsc95xx USB network devices
from a the device tree. This is required to get a usable persistent
address on the popular beagleboard, whose hardware designers
accidentally forgot that an ethernet device really requires an a
MAC address to be functional.
The Raspberry Pi also ships smsc9514 without a serial EEPROM, stores
the MAC address in ROM accessible via VC4 firmware.
The smsc75xx and smsc95xx drivers are just two copies of the
same code, so better fix both.
[lkundrak@v3.sk: updated to use of_get_property() as per suggestion from
Arnd, reworded the message and comments a bit]
Tested-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Abstract TTY_THROTTLED bit tests with tty_throttled().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The default Pegasus setup was to append the status and CRC at the end of each
received packet. The status bits are used to update various stats, but CRC has
been ignored. The new default is to not append CRC at the end of RX packets.
Signed-off-by: Petko Manolov <petkan@mip-labs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
usb_fill_bulk_urb() receives buffer length parameter 8 bytes larger
than what's allocated by alloc_skb(); This seems to be a problem with
older (pegasus usb-1.1) devices, which may silently return more data
than the maximal packet length.
Reported-by: Lincoln Ramsay <a1291762@gmail.com>
Signed-off-by: Petko Manolov <petkan@mip-labs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At forced 100 Full & Half duplex mode, chip may fail to set mode correctly
when cable is switched between long(~50+m) and short one.
As workaround, set to 10 before setting to 100 at forced 100 F/H mode.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix rx_bytes, tx_bytes and tx_frames error in netdev.stats.
- rx_bytes counted bytes excluding size of struct ethhdr.
- tx_packets didn't count multiple packets in a single urb
- tx_bytes included 8 bytes of extra commands.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now have a positive report of another Huawei device needing
this quirk: The ME906s-158 (12d1:15c1). This is an m.2 form
factor modem with no obvious relationship to the E3372 (12d1:157d)
we already have a quirk entry for. This is reason enough to
believe the quirk might be necessary for any number of current
and future Huawei devices.
Applying the quirk to all Huawei devices, since it is crucial
to any device affected by the firmware bug, while the impact
on non-affected devices is negligible.
The quirk can if necessary be disabled per-device by writing
N to /sys/class/net/<iface>/cdc_ncm/ndp_to_end
Reported-by: Andreas Fett <andreas.fett@secunet.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Telit LE910 V2 is a mobile broadband card with no ARP capabilities:
the patch makes this device to use wwan_noarp_info struct
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit a59f8c5b04.
There are several bugs in this new code, for example:
1) Uses sleeping locks in get_stats64, which is not allowed,
as the operation can be invoked in an atomic context.
2) Uses PM fields without CONFIG_PM or similar guards.
3) Does not synchronize HW stats when the device runtime
suspends.
Therefore this is being reverted until a correct version
is implemented.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add lan78xx_get_stats64 of ndo_get_stats64 to report
all statistics counters including errors from HW statistics.
Read from HW when auto suspend is disabled, use saved counter when
auto suspend is enabled because periodic call to ndo_get_stats64
prevents USB auto suspend.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update to handle statistics counter rollover.
Check statistics counter periodically and compensate it when
counter value rolls over at max (20 or 32bits).
Simple mechanism adjusts monitoring timer to allow USB auto suspend.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for Gemalto's Cinterion PHxx WWAN interfaces
by adding QMI_FIXED_INTF with Cinterion's VID and PID.
PHxx can have:
2 RmNet Interfaces (PID 0x0082) or
1 RmNet + 1 USB Audio interface (PID 0x0083).
Signed-off-by: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
usbnet_link_change will call schedule_work and should be
avoided if bind is failing. Otherwise we will end up with
scheduled work referring to a netdev which has gone away.
Instead of making the call conditional, we can just defer
it to usbnet_probe, using the driver_info flag made for
this purpose.
Fixes: 8a34b0ae87 ("usbnet: cdc_ncm: apply usbnet_link_change")
Reported-by: Andrey Konovalov <andreyknvl@gmail.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some devices will silently fail setup unless they are reset first.
This is necessary even if the data interface is already in
altsetting 0, which it will be when the device is probed for the
first time. Briefly toggling the altsetting forces a function
reset regardless of the initial state.
This fixes a setup problem observed on a number of Huawei devices,
appearing to operate in NTB-32 mode even if we explicitly set them
to NTB-16 mode.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case bind() works, but a later error forces bailing
in probe() in error cases work and a timer may be scheduled.
They must be killed. This fixes an error case related to
the double free reported in
http://www.spinics.net/lists/netdev/msg367669.html
and needs to go on top of Linus' fix to cdc-ncm.
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Used to be allocated and required freeing, but now
priv->mdio->irq is now a fixed sized array and should no longer be
free'd.
Issue detected using static analysis with CoverityScan
Fixes: e7f4dc3536 ("mdio: Move allocation of interrupts into core")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MC74xx and EM74xx modules use different IDs by default, according
to the Lenovo EM7455 driver for Windows.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool operations of set_pauseram and get_pauseparm.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not required after commit cd772de358
("phy: keep pause flags in phy driver features")
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace devid to chipid & chiprev for easy access.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This avoids a harmless randconfig warning I get when USB_NET_CDC_SUBSET
is enabled, but all of the more specific drivers are not:
drivers/net/usb/cdc_subset.c:241:2: #warning You need to configure some hardware for this driver
The current behavior is clearly intentional, giving a warning when
a user picks a configuration that won't do anything good. The only
reason for even addressing this is that I'm getting close to
eliminating all 'randconfig' warnings on ARM, and this came up
a couple of times.
My workaround is to not even build the module when none of the
configurations are enable.
Alternatively we could simply remove the #warning (nothing wrong
for compile-testing), turn it into a runtime warning, or
change the Kconfig options into a menu to hide CONFIG_USB_NET_CDC_SUBSET.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Throttle TX path only at slower than SuperSpeed USB.
SuperSpeed USB has enough bandwidth to maintain GigE.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depends on chip, some EEPROM pins are muxed with LED function.
Disable & restore LED function to access EEPROM.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update lan78xx to use patch of commit 4f2aaf7dd9
("Merge branch 'fix-phy-ignore-interrupts'").
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_main.c
drivers/net/ethernet/mellanox/mlxsw/spectrum.h
drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c
The bond_main.c and mellanox switch conflicts were cases of
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
SIMCom 7230E is a QMI LTE module with support for most "normal" bands.
Manual testing has showed that only interface five works.
Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The union descriptor must be checked. Its usage was conditional
before the parser was introduced. This is important, because
many RNDIS device, which also use the common parser, have
bogus extra descriptors.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Tested-by: Vasily Galkin <galkin-vv@yandex.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace disable_aldps() and enable_aldps() with aldps_en().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace test_bit() followed by clear_bit() with test_and_clear_bit().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the autosuspend is enabled and occurs before system suspend, we should
wake the device before running system syspend. Then, we could change the wake
event for system suspend. Otherwise, the device would resume the system when
receiving any packet.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug writing to EEPROM in lan78xx_ethtool_set_eeprom()
when asked to write to OTP.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have mdio_alloc() create the array of interrupt numbers, and
initialize it to POLLING. This is what most MDIO drivers want, so
allowing code to be removed from the drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The WeTelecom-WPD600N is an LTE module that, in addition to supporting most
"normal" bands, also supports LTE over 450MHz. Manual testing showed that
only interface number three replies to QMI messages.
Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the reset_resume() is called, the flag of SELECTIVE_SUSPEND should be
cleared and reinitialize the device, whether the SELECTIVE_SUSPEND is set
or not. If reset_resume() is called, it means the power supply is cut or the
device is reset. That is, the device wouldn't be in runtime suspend state and
the reinitialization is necessary.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NCM buffer sizes are negotiated with the device independently of
the network device MTU. The RX buffers are allocated by the
usbnet framework based on the rx_urb_size value set by cdc_ncm. A
single RX buffer can hold a number of MTU sized packets.
The default usbnet change_mtu ndo only modifies rx_urb_size if it
is equal to hard_mtu. And the cdc_ncm driver will set rx_urb_size
and hard_mtu independently of each other, based on dwNtbInMaxSize
and dwNtbOutMaxSize respectively. It was therefore assumed that
usbnet_change_mtu() would never touch rx_urb_size. This failed to
consider the case where dwNtbInMaxSize and dwNtbOutMaxSize happens
to be equal.
Fix by implementing an NCM specific change_mtu ndo, modifying the
netdev MTU without touching the buffer size settings.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike DW5550, Dell DW5813 is a mobile broadband card with no ARP
capabilities: the patch makes this device to use wwan_noarp_info struct
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike DW5550, Dell DW5812 is a mobile broadband card with no ARP
capabilities: the patch makes this device to use wwan_noarp_info struct
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since it is possible for an external system to send oversize packets
at anytime, it is best for driver not to print a message and spam
the log (potential external DoS).
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=109471
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
The CDC descriptors found on these vendor specific functions should
not be considered authoritative. They seem to be ignored by drivers
for other systems, and the quality is therefore low.
One device (1e0e:9001) has been reported to have such a bogus union
descriptor on the QMI function, making it fail probing even if the
device id was dynamically added. The report was not complete enough
to allow adding a device entry for this modem. But this should at
least fix the dynamic id probing problem.
Reported-by: Kanerva Topi <Topi.Kanerva@cinia.fi>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The name NETIF_F_ALL_CSUM is a misnomer. This does not correspond to the
set of features for offloading all checksums. This is a mask of the
checksum offload related features bits. It is incorrect to set both
NETIF_F_HW_CSUM and NETIF_F_IP_CSUM or NETIF_F_IPV6 at the same time for
features of a device.
This patch:
- Changes instances of NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK (where
NETIF_F_ALL_CSUM is being used as a mask).
- Changes bonding, sfc/efx, ipvlan, macvlan, vlan, and team drivers to
use NEITF_F_HW_CSUM in features list instead of NETIF_F_ALL_CSUM.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an interface is brought up which was previously suspended (via
runtime PM), it would hang. This happens because napi_disable is called
before napi_enable.
Solve this by avoiding napi_enable in the resume during open function
(netif_running is true when open is called, IFF_UP is set after a
successful open; netif_running is false when close is called, but IFF_UP
is then still set).
While at it, remove WORK_ENABLE check from rtl8152_open (introduced with
the original change) because it cannot happen:
- After this patch, runtime resume will not set it during rtl8152_open.
- When link is up, rtl8152_open is not called.
- When link is down during system/auto suspend/resume, it is not set.
Fixes: 41cec84cf2 ("r8152: don't enable napi before rx ready")
Link: https://lkml.kernel.org/r/20151205105912.GA1766@al
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a writable sysfs attribute for the "NDP to end"
quirk flag.
This makes it easier for end users to test new devices for
this firmware bug. We've been lucky so far, but we should
not depend on reporters capable of rebuilding the driver.
Cc: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The notifier calls were thrown in as a last-minute fix for an
imagined "this device could be part of a bridge" problem. That
revealed a certain lack of locking. Not to mention testing...
Avoid this splat:
RTNL: assertion failed at net/core/dev.c (1639)
CPU: 0 PID: 4293 Comm: bash Not tainted 4.4.0-rc3+ #358
Hardware name: LENOVO 2776LEG/2776LEG, BIOS 6EET55WW (3.15 ) 12/19/2011
0000000000000000 ffff8800ad253d60 ffffffff8122f7cf ffff8800ad253d98
ffff8800ad253d88 ffffffff813833ab 0000000000000002 ffff880230f48560
ffff880230a12900 ffff8800ad253da0 ffffffff813833da 0000000000000002
Call Trace:
[<ffffffff8122f7cf>] dump_stack+0x4b/0x63
[<ffffffff813833ab>] call_netdevice_notifiers_info+0x3d/0x59
[<ffffffff813833da>] call_netdevice_notifiers+0x13/0x15
[<ffffffffa09be227>] raw_ip_store+0x81/0x193 [qmi_wwan]
[<ffffffff8131e149>] dev_attr_store+0x20/0x22
[<ffffffff811d858b>] sysfs_kf_write+0x49/0x50
[<ffffffff811d8027>] kernfs_fop_write+0x10a/0x151
[<ffffffff8117249a>] __vfs_write+0x26/0xa5
[<ffffffff81085ed4>] ? percpu_down_read+0x53/0x7f
[<ffffffff81174c9e>] ? __sb_start_write+0x5f/0xb0
[<ffffffff81174c9e>] ? __sb_start_write+0x5f/0xb0
[<ffffffff81172c37>] vfs_write+0xa3/0xe7
[<ffffffff811734ad>] SyS_write+0x50/0x7e
[<ffffffff8145c517>] entry_SYSCALL_64_fastpath+0x12/0x6f
Fixes: 32f7adf633 ("net: qmi_wwan: support "raw IP" mode")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Huawei E3372 (12d1:157d) needs this quirk in MBIM mode
as well. Allow this by forcing the NTB to contain only a
single NDP, and add a device specific entry for this ID.
Due to the way Huawei use device IDs, this might be applied
to other modems as well. It is assumed that those modems
will be based on the same firmware and will need this quirk
too. If not, it will still not harm normal usage, although
multiplexing performance could be impacted.
Cc: Enrico Mioso <mrkiko.rs@gmail.com>
Reported-by: Sami Farin <hvtaifwkbgefbaei@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-By: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
QMI wwan devices have traditionally emulated ethernet devices
by default. But they have always had the capability of operating
without any L2 header at all, transmitting and receiving "raw"
IP packets over the USB link. This firmware feature used to be
configurable through the QMI management protocol.
Traditionally there was no way to verify the firmware mode
without attempting to change it. And the firmware would often
disallow changes anyway, i.e. due to a session already being
established. In some cases, this could be a hidden firmware
internal session, completely outside host control. For these
reasons, sticking with the "well known" default mode was safest.
But newer generations of QMI hardware and firmware have moved
towards defaulting to "raw IP" mode instead, followed by an
increasing number of bugs in the already buggy "802.3" firmware
implementation. At the same time, the QMI management protocol
gained the ability to detect the current mode. This has enabled
the userspace QMI management application to verify the current
firmware mode without trying to modify it.
Following this development, the latest QMI hardware and firmware
(the MDM9x30 generation) has dropped support for "802.3" mode
entirely. Support for "raw IP" framing in the driver is therefore
necessary for these devices, and to a certain degree to work
around problems with the previous generation,
This patch adds support for "raw IP" framing for QMI devices,
changing the netdev from an ethernet device to an ARPHRD_NONE
p-t-p device when "raw IP" framing is enabled.
The firmware setup is fully delegated to the QMI userspace
management application, through simple tunneling of the QMI
protocol. The driver will therefore not know which mode has been
"negotiated" between firmware and userspace. Allowing userspace
to inform the driver of the result through a sysfs switch is
considered a better alternative than to change the well established
clean delegation of firmware management to userspace.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Assume the minidriver has taken care of all L2 header parsing
if it sets skb->protocol. This allows the minidriver to
support non-ethernet L2 headers, and even operate without
any L2 header at all.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This turned out to be a bootloader device ID. No need for
that in this driver. It will only provide a single serial
function.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDM9x30 based modems appear to go into a deeper sleep when
suspended without "Remote Wakeup" enabled. The QMI interface
will not respond unless a "set DTR" control request is sent
on resume. The effect is similar to a QMI_CTL SYNC request,
resetting (some of) the firmware state.
We allow userspace sessions to span multiple character device
open/close sequences. This means that userspace can depend
on firmware state while both the netdev and the character
device are closed. We have disabled "needs_remote_wakeup" at
this point to allow devices without remote wakeup support to
be auto-suspended.
To make sure the MDM9x30 keeps firmware state, we need to
keep "needs_remote_wakeup" always set. We also need to
issue a "set DTR" request to enable the QMI interface.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 77b0a09967 ("cdc-ncm: use common parser") added a dangerous
new trust in the CDC functional descriptors presented by the device,
unconditionally assuming that any device handled by the driver has
a CDC Union descriptor.
This descriptor is required by the NCM and MBIM specs, but crashing
on non-compliant devices is still unacceptable. Not only will that
allow malicious devices to crash the kernel, but in this case it is
also well known that there are non-compliant real devices on the
market - as shown by the comment accompanying the IAD workaround
in the same function.
The Sierra Wireless EM7305 is an example of such device, having
a CDC header and a CDC MBIM descriptor but no CDC Union:
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 12
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 2 Communications
bInterfaceSubClass 14
bInterfaceProtocol 0
iInterface 0
CDC Header:
bcdCDC 1.10
CDC MBIM:
bcdMBIMVersion 1.00
wMaxControlMessage 4096
bNumberFilters 16
bMaxFilterSize 128
wMaxSegmentSize 4064
bmNetworkCapabilities 0x20
8-byte ntb input size
Endpoint Descriptor:
..
The conversion to a common parser also left the local cdc_union
variable untouched. This caused the IAD workaround code to be applied
to all devices with an IAD descriptor, which was never intended. Finish
the conversion by testing for hdr.usb_cdc_union_desc instead.
Cc: Oliver Neukum <oneukum@suse.com>
Fixes: 77b0a09967 ("cdc-ncm: use common parser")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas reports
"
4gsystems sells two total different LTE-surfsticks under the same name.
..
The newer version of XS Stick W100 is from "omega"
..
Under windows the driver switches to the same ID, and uses MI03\6 for
network and MI01\6 for modem.
..
echo "1c9e 9b01" > /sys/bus/usb/drivers/qmi_wwan/new_id
echo "1c9e 9b01" > /sys/bus/usb-serial/drivers/option1/new_id
T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1c9e ProdID=9b01 Rev=02.32
S: Manufacturer=USB Modem
S: Product=USB Modem
S: SerialNumber=
C: #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
Now all important things are there:
wwp0s29f7u2i3 (net), ttyUSB2 (at), cdc-wdm0 (qmi), ttyUSB1 (at)
There is also ttyUSB0, but it is not usable, at least not for at.
The device works well with qmi and ModemManager-NetworkManager.
"
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since Dell DW5580 is a 3G modem, this patch adds the device as a
mobile broadband adapter
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge final patch-bomb from Andrew Morton:
"Various leftovers, mainly Christoph's pci_dma_supported() removals"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
pci: remove pci_dma_supported
usbnet: remove ifdefed out call to dma_supported
kaweth: remove ifdefed out call to dma_supported
sfc: don't call dma_supported
nouveau: don't call pci_dma_supported
netup_unidvb: use pci_set_dma_mask insted of pci_dma_supported
cx23885: use pci_set_dma_mask insted of pci_dma_supported
cx25821: use pci_set_dma_mask insted of pci_dma_supported
cx88: use pci_set_dma_mask insted of pci_dma_supported
saa7134: use pci_set_dma_mask insted of pci_dma_supported
saa7164: use pci_set_dma_mask insted of pci_dma_supported
tw68-core: use pci_set_dma_mask insted of pci_dma_supported
pcnet32: use pci_set_dma_mask insted of pci_dma_supported
lib/string.c: add ULL suffix to the constant definition
hugetlb: trivial comment fix
selftests/mlock2: add ULL suffix to 64-bit constants
selftests/mlock2: add missing #define _GNU_SOURCE
This device has same vendor and product IDs as G2K devices, but it has
different number of interfaces(4 vs 5) and also different interface
layout where EC20 has QMI on interface 4 instead of 0.
lsusb output:
Bus 002 Device 003: ID 05c6:9215 Qualcomm, Inc. Acer Gobi 2000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x05c6 Qualcomm, Inc.
idProduct 0x9215 Acer Gobi 2000 Wireless Modem
bcdDevice 2.32
iManufacturer 1 Quectel
iProduct 2 Quectel LTE Module
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 209
bNumInterfaces 5
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 500mA
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes in net/ipv4/ipmr.c, in 'net' we were
fixing the "BH-ness" of the counter bumps whilst in 'net-next'
the functions were modified to take an explicit 'net' parameter.
Signed-off-by: David S. Miller <davem@davemloft.net>
The lt4112 is a HP branded Huawei me906e modem. Like other Huawei
modems, it does not have a fixed interface to function mapping.
Instead it uses a Huawei specific scheme: functions are mapped by
subclass and protocol.
However, the HP vendor ID is used for modems from many different
manufacturers using different schemes, so we cannot apply a generic
vendor rule like we do for the Huawei vendor ID.
Replace the previous lt4112 entry pointing to an arbitrary interface
number with a device specific subclass + protocol match.
Reported-and-tested-by: Muri Nicanor <muri+libqmi@immerda.ch>
Tested-by: Martin Hauke <mardnh@gmx.de>
Fixes: bb2bdeb83f ("qmi_wwan: Add support for HP lt4112 LTE/HSPA+ Gobi 4G Modem")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv6/xfrm6_output.c
net/openvswitch/flow_netlink.c
net/openvswitch/vport-gre.c
net/openvswitch/vport-vxlan.c
net/openvswitch/vport.c
net/openvswitch/vport.h
The openvswitch conflicts were overlapping changes. One was
the egress tunnel info fix in 'net' and the other was the
vport ->send() op simplification in 'net-next'.
The xfrm6_output.c conflicts was also a simplification
overlapping a bug fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
New device IDs shamelessly lifted from the vendor driver.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Just another AX88178-based 10/100/1000 USB-to-Ethernet dongle. This one
shows up in lsusb as: "ID 08dd:0114 Billionton Systems, Inc".
Signed-off-by: Chia-Sheng Chang <changchias@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Christoph Jaeger <cj@linux.com>
Cc: "Woojung.Huh@microchip.com" <Woojung.Huh@microchip.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Markus Elfring <elfring@users.sourceforge.net>
Cc: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: netdev@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Many drivers initialize uselessly n_priv_flags, n_stats, testinfo_len,
eedump_len & regdump_len fields in their .get_drvinfo() ethtool op.
It's not necessary as these fields is filled in ethtool_get_drvinfo().
v2: removed unused variable
v3: removed another unused variable
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid a loss of synchronisation of the Ethernet Data header 32-bit
word due to a failure to get a netdev socket buffer.
The ASIX RX handling algorithm returned 0 upon a failure to get
an allocation of a netdev socket buffer. This causes the URB
processing to stop which potentially causes a loss of synchronisation
with the Ethernet Data header 32-bit word. Therefore, subsequent
processing of URBs may be rejected due to a loss of synchronisation.
This may cause additional good Ethernet frames to be discarded
along with outputting of synchronisation error messages.
Implement a solution which checks whether a netdev socket buffer
has been allocated before trying to copy the Ethernet frame into
the netdev socket buffer. But continue to process the URB so that
synchronisation is maintained. Therefore, only a single Ethernet
frame is discarded when no netdev socket buffer is available.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Mark Craske <Mark_Craske@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When RX Ethernet frames span multiple URB socket buffers,
the data stream may suffer a discontinuity which will cause
the current Ethernet frame in the netdev socket buffer
to be incomplete. This frame needs to be discarded instead
of appending unrelated data from the current URB socket buffer
to the Ethernet frame in the netdev socket buffer. This avoids
creating a corrupted Ethernet frame in the netdev socket buffer.
A discontinuity can occur when the previous URB socket buffer
held an incomplete Ethernet frame due to truncation or a
URB socket buffer containing the end of the Ethernet frame
was missing.
Therefore, add a sanity test for when an Ethernet frame
spans multiple URB socket buffers to check that the remaining
bytes of the currently received Ethernet frame point to
a good Data header 32-bit word of the next Ethernet
frame. Upon error, reset the remaining bytes variable to
zero and discard the current netdev socket buffer.
Assume that the Data header is located at the start of
the current socket buffer and attempt to process the next
Ethernet frame from there. This avoids unnecessarily
discarding a good URB socket buffer that contains a new
Ethernet frame.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Mark Craske <Mark_Craske@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code is checking that the Ethernet frame will fit into a
netdev allocated socket buffer within the constraints of MTU size,
Ethernet header length plus VLAN header length.
The original code was checking rx->remaining each loop of the while
loop that processes multiple Ethernet frames per URB and/or Ethernet
frames that span across URBs. rx->remaining decreases per while loop
so there is no point in potentially checking multiple times that the
Ethernet frame (remaining part) will fit into the netdev socket buffer.
The modification checks that the size of the Ethernet frame will fit
the netdev socket buffer before allocating the netdev socket buffer.
This avoids grabbing memory and then deciding that the Ethernet frame
is too big and then freeing the memory.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Mark Craske <Mark_Craske@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tidy-up the Data header 32-bit word synchronisation logic in
asix_rx_fixup_internal() by removing redundant logic tests.
The code is looking at the following cases of the Data header
32-bit word that is present before each Ethernet frame:
a) all 32 bits of the Data header word are in the URB socket buffer
b) first 16 bits of the Data header word are at the end of the URB
socket buffer
c) last 16 bits of the Data header word are at the start of the URB
socket buffer eg. split_head = true
Note that the lifetime of rx->split_head exists outside of the
function call and is accessed per processing of each URB. Therefore,
split_head being true acts on the next URB to be processed.
To check for b) the offset will be 16 bits (2 bytes) from the end of
the buffer then indicate split_head is true.
To check for c) split_head must be true because the first 16 bits
have been found.
To check for a) else c)
Note that the || logic of the old code included the state
(skb->len - offset == sizeof(u16) && rx->split_head) which is not
possible because the split_head cannot be true whilst checking for b).
This is because the split_head indicates that the first 16 bits have
been found and that is not possible whilst checking for the first 16
bits. Therefore simplify the logic.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Mark Craske <Mark_Craske@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Data header synchronisation is easier to understand
if the variables "remaining" and "size" are renamed.
Therefore, the lifetime of the "remaining" variable exists
outside of asix_rx_fixup_internal() and is used to indicate
any remaining pending bytes of the Ethernet frame that need
to be obtained from the next socket buffer. This allows an
Ethernet frame to span across multiple socket buffers.
"size" is now local to asix_rx_fixup_internal() and contains
the size read from the Data header 32-bit word.
Add "copy_length" to hold the number of the Ethernet frame
bytes (maybe a part of a full frame) that are to be copied
out of the socket buffer.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Mark Craske <Mark_Craske@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If asix_rx_fixup_internal() fails to allocate rx->ax_skb, it will return
but not clear rx->size. rx points to driver private data. A later call
assumes that nonzero size means ax_skb was allocated and passes a null
ax_skb to skb_put. Changed allocation failure return to clear size first.
Found testing board with AX88772B devices.
Signed-off-by: David B. Robins <linux@davidrobins.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
lan78xx_suspend() may return non-zero from lan78xx_write_reg() in some scenario.
Fix to return 0 when lan78xx_suspend() has no error.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv4/arp.c
The net/ipv4/arp.c conflict was one commit adding a new
local variable while another commit was deleting one.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 12fd84f438 ("ipv6: Remove unused neigh argument for
icmp6_dst_alloc() and its callers."), the neigh parameter of ndisc_send_na
and ndisc_send_ns is unused.
CC: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converts the ch9200 driver to use the module_usb_driver() macro which
makes the code smaller and a bit simpler.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->len is always non-negative.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2038576
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a bunch of cheap USB 10/100 devices based on QinHeng chipsets. The
vendor driver supports the CH9100 and CH9200 devices, but the majority of
the code is of the if (ch9100) {} else {} form, with the most significant
difference being that CH9200 provides a real MII interface but CH9100 fakes
one with a bunch of global variables and magic commands. I don't have a
CH9100, so it's probably better if someone who does provides an independent
driver for it. In any case, this is a lightly cleaned up version of the
vendor driver with all the CH9100 code dropped.
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove not defined MAC_CR_GMII_EN_ bit from MAC_CR.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create lan78xx_get_mdix_status() and lan78xx_set_mdix_status() for MDIX control.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove phy defines in lan78xx.h and use defines in include/linux/microchipphy.h.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update to use phylib instead of mii_if_info.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PHYLIB and MICROCHIP_PHY as default configuration for lan78xx.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check device ready bit (PMT_CTL_READY_) after reset the PHY.
Device may not be ready even if PHY_RST_ is cleared depends on configuration.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
