The AC97 wire format is completely fixed so CODECs don't have any choice
about the formats they accept but controllers accept a variety of data
formats and render them down onto the bus. Have a shared define so all
the CODEC drivers will interoperate with any of our controller drivers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
They aren't used by anything external and aren't prototyped; if any
users appear they can be exported again for them.
Also report what modes we have a problem with when we encounter invalid
mode configurations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
On startup we try to make sure that the port is quiesced but if the
port is already stopped then this will generate a warning about the
RX/TX mode configuration. Configure the mode before doing the teardown
to suppress these warnings.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The data format configuration for S3C64xx IISv2 is completely different
to that for S3C24xx. Instead of a single bit configuration in bit 0 of
IISMOD we have format selection in bits 13 and 14 and bit clock rate
selection in bits 1 and 2. While we're here add support for 24 bit
samples in S3C64xx.
At some point it may be desirable to expose the bit clock rate selection
to users but given the limited configuration options that may not be
required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This makes the interface usable with the s3c-iis-v2 rate calculator
and consistent with S3C2412.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The gain control for earpiece amplifier uses 0dB ~ 12dB according to the
TRM, but the present code is implemented to -6dB ~ 6dB.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We need to check only if the WM8350 is master and only when starting
the stream so if either is not true then we can skip the check.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This adds a new control named 'Master Playback Switch' for cs4270
codecs. It is implemented using the new SOC_DOUBLE_EXT macro to catch
the put function and store the information about manually set mute
controls from userspace. When a manual mute is set, we don't want the
soc core to un-mute the outputs.
Renamed cs4270_mute() to cs4270_dai_mute() to avoid confusion.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The control modifies the MUTE register, hence the polarity must be
inverted.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-By: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Say what invalid values we're seeing when we see an invalid value and
ensure that errors are displayed by default.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's expected behaviour for the CODEC header to provide them but the
WM8350 doesn't due to having all the registers together under drivers/mfd.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The S3C64xx IIS code had a number of problems with device registration.
The hardware has two IIS ports of which the driver supported only one
at once via a single exported DAI, attempting to identify the DAI to
use based on the dev->id of the ASoC platform device. As well as
limiting the driver to only supporting one IIS port at once this also
meant that the ID of the soc-audio device (or in future the card device)
had to match the IIS ID.
Fix both problems by converting the driver to register the DAIs based on
probing of platform devices registered by the arch/arm code, using those
platform devices to interact with the clock API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a macro for double controls with special callback functions.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the four channel TDM mode
on Beagle board.
Depending on the channel count, the interface needs to be
configured differently (I2S for stereo DSP_A for four channels)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add 4 channel support to omap-mcbsp.
This mode is going to be used by the twl4030 codec, when it
is configured in Option1 mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The original idea came from pHilipp, and this makes the code looks
more consistent.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The SSP DMA parameters can actually be easily generated at run-time since
they are almost similar except for the FIFO width and direction. Another
benefit is the re-use of information from 'struct ssp_device', like SSDR
physical FIFO address and DRCMR register index for both directions.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: pHilipp Zabel <philipp.zabel@gmail.com>
Add DAPMs for VDL(Voice Down Link) path. To support VDL path, we have
to change DAPMs of outputs(Earpiece, PreDrive Left/Right, Headset
Left/Right, Carkit Left/Right) from mux to mixer.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Save a little extra power by enabling the DC servo offset correction
for the output channels only when the relevant channels are enabled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Modify the default startup sequence in the chip to set the DC servo
dither level for optimal performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CLK_DSP provides a master clock for the DAC and ADC related functionality
on the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Many modern CODECs have shared resources on chip which must be enabled
for portions of the chip to work but which can be disabled at other times
in order to achieve power savings. Examples of such resources include
power supplies and some internal clocks.
Since these widgets are dependencies for the audio path but do not carry
audio signals they require slightly different handling to most widgets -
they do not contribute to the audio path and so should not be counted as
either inputs or outputs during path walks.
Cases where one supply provides a supply for another will require
additional work. There is also room for more optimisation of the graph
walking to avoid repeated checks for the same thing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add checking in hw_params and prepare to detect bufferless pcms(i.e. BT
<--> codec).
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than having switch statements at point of use make the DAPM
power check a member of the widget structure and set it when we
instantiate the widget.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This also switches us to using a switch statement for the widget type
in dapm_power_widget().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
