Patch from Ben Dooks
Add USB bus clock definition for 48MHz fed to OHCI and gadget cores
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add set_rate methods for the extra clocks on the S3C2440
and add the camera UPLL clock source
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add support for clk_set_rate and clk_round_rate to the
s3c2410 clock implementation
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Move the uengine loader from arch/arm/mach-ixp2000 to arch/arm/common
so that ixp23xx can use it too.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Add ep93xx defconfig.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Add support for setting the direction of and getting/setting the
value of the 64 GPIO lines.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
This patch adds support for the Cirrus ep93xx series of CPUs. The
ep93xx is an ARM920T based CPU with two VICs, PL010 based UARTs,
IrDA, MaverickCrunch floating point coprocessor, between 24 and 64
GPIOs, ethernet, OHCI USB and, depending on the model, pcmcia, raster
engine, graphics accelerator, IDE controller and a bunch of other
stuff.
This patch adds the core ep93xx support code, and support for the
Glomation GESBC-9312-sx and the Technologic Systems TS-72xx SBCs.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Alessandro Zummo
ixp4xx_config_irq did not configure the gpio line
as an input.
As an added bonus, the irq2gpio array has been converted
from int to char.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Alessandro Zummo
This patch adds a few defines that are useful
to configure the CS regions on ixp4xx.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: OEyvind Repvik <oyvind@repvik.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Peter Teichmann
Currently, if the kernels HZ value is greater than 100, delays with the udelay function are too short. This can cause trouble for instance with the zd1201 usb wlan driver.
This patch suggests a solution that keeps the overhead small and maintains (hopefully) sufficient resolution.
Signed-off-by: Peter Teichmann
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
This patch adds support for Intel's IXDP28x5 platform. This
is just and IXDP2801 with a new CPU rev but the bootloader
has been updated to reflect a new machine ID so we just build
support for it by default when we build IXDP2801.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add enable and set_parent calls for the dclk
and clkout clocks.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add devices that we have drivers for, and
update list of machines that are supported
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add clk_set_parent() call to clock code
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Move the UPLL clock registration to the central
clock file, and add an enable method
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add selection for timer code for the Simtec Osiris
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Support for Simtec IM2440D20 CPU modules (Osiris)
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
This field is redundent since it must be equal to PHYS_OFFSET anyway.
There is no reference to it anymore so remove it at last.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Several ARM machine implementations used a PL01x primecell compatible
serial port for debugging purposes, and indepdently implemented the low
level debug macros every time. Provide a common implementation and
convert these implementations to use this version.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Several ARM machine implementations used an 8250 compatible port for
debugging purposes, and indepdently implemented the low level debug
macros every time. Provide a common implementation and convert these
implementations to use this version.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some SoCs have multiple VIC devices. Adapt the generic vic code
to allow multiple implementations to be handled.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In all current use cases, "chipdata" is used to store an iomem address.
Mark it with __iomem, and rename it to 'base'. Leave the accessor macros
alone.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow the individual coprocessor handlers to decide when to enable
interrupts, rather than unconditionally enabling them.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
asm/hardware.h is not required for the majority of processor support
files, ioremap support, mm initialisation, acorn IO support, nor
the debug code (which picks up its machine specific includes via
debug-macros.S)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Unfortunately, OMAP platforms without the 32K timer left HZ set to
an empty value. Fix this by making the dependency on OMAP_32K_TIMER
rather than OMAP_32K_TIMER_HZ.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
asm/arch/irq.h used to be included from asm/irq.h, but was removed
from the ARM kernel a long time ago. Consequently, the contents
of asm/arch/irq.h (which mostly contain a definition for fixup_irq())
have not been used. Hence, remove asm/arch/irq.h.
Some machine support files incorrectly included this file, making
little or no use of the contents. Move the contents to a local
include file, and remove those include statements as well.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the HZ definition into Kconfig, and set appropriate defaults
for platforms. Remove mostly empty asm/arch/param.h include file.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/pub/scm/linux/kernel/git/herbert/crypto-2.6:
[CRYPTO] aes: Fixed array boundary violation
[CRYPTO] tcrypt: Fix key alignment
[CRYPTO] all: Add missing cra_alignmask
[CRYPTO] all: Use kzalloc where possible
[CRYPTO] api: Align tfm context as wide as possible
[CRYPTO] twofish: Use rol32/ror32 where appropriate
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (23 commits)
[PATCH] sysfs: fix a kobject leak in sysfs_add_link on the error path
[PATCH] sysfs: don't export dir symbols
[PATCH] get_cpu_sysdev() signedness fix
[PATCH] kobject_add_dir
[PATCH] debugfs: Add debugfs_create_blob() helper for exporting binary data
[PATCH] sysfs: fix problem with duplicate sysfs directories and files
[PATCH] Kobject: kobject.h: fix a typo
[PATCH] Kobject: provide better warning messages when people do stupid things
[PATCH] Driver core: add macros notice(), dev_notice()
[PATCH] firmware: fix BUG: in fw_realloc_buffer
[PATCH] sysfs: kzalloc conversion
[PATCH] fix module sysfs files reference counting
[PATCH] add EXPORT_SYMBOL_GPL_FUTURE() to USB subsystem
[PATCH] add EXPORT_SYMBOL_GPL_FUTURE() to RCU subsystem
[PATCH] add EXPORT_SYMBOL_GPL_FUTURE()
[PATCH] Clean up module.c symbol searching logic
[PATCH] kobj_map semaphore to mutex conversion
[PATCH] kref: avoid an atomic operation in kref_put()
[PATCH] handle errors returned by platform_get_irq*()
[PATCH] driver core: platform_get_irq*(): return -ENXIO on error
...
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial:
README: bzip2 is not new
Documentation/Changes: remove outdated translation references
remove dead Radeon URL
SCSI_AACRAID: add a help text
update the i386 defconfig
MAINTAINERS: remove the LANMEDIA entry
Move ip2.c and ip2main.c to drivers/char/ip2/ where the other files
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Update defconfigs.
[MIPS] Separate CPU entries in /proc/cpuinfo with a blank line.
[MIPS] sys_mmap2 offset argument should always be shifted 12, not PAGE_SHIFT.
[MIPS] TX49XX has prefetch.
[MIPS] Kill tlb-andes.c.
[MIPS] War on whitespace: cleanup initial spaces followed by tabs.
[MIPS] Makefile crapectomy.
[MIPS] Reformat __xchg().
[MIPS] Mention Broadcom part number for BigSur board
[MIPS] Remove CONFIG_BUILD_ELF64.
[MIPS] Further sparsification for 32-bit compat code.
[MIPS] fix wrong __user usage in _sysn32_rt_sigsuspend
[MIPS] Signal cleanup
[MIPS] Reformat all of signal32.c with tabs instead of space for consistency
[MIPS] Delete unused sys32_waitpid.
[MIPS] Make I/O helpers more customizable
[MIPS] Symmetric Uniprocessor support for Qemu.
[MIPS] sc-rm7k.c cleanup
[MIPS] MIPS64 R2 optimizations for 64-bit endianess swapping.
[MIPS] Add early console for Cobalt.
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband: (47 commits)
IB/mthca: Query SRQ srq_limit fixes
IPoIB: Get rid of useless test of queue length
IB/mthca: Correct reported SRQ size in MemFree case.
IB/mad: Fix oopsable race on device removal
IB/srp: Coverity fix to srp_parse_options()
IB/mthca: Coverity fix to mthca_init_eq_table()
IB: Coverity fixes to sysfs.c
IPoIB: Move ipoib_ib_dev_flush() to ipoib workqueue
IPoIB: Fix build now that neighbour destructor is in neigh_params
IB/uverbs: Use correct alt_pkey_index in modify QP
IB/umad: Add support for large RMPP transfers
IB/srp: Add SCSI host attributes to show target port
IB/cm: Check cm_id state before handling a REP
IB/mthca: Update firmware versions
IB/mthca: Optimize large messages on Sinai HCAs
IB/uverbs: Fix query QP return of sq_sig_all
IB: Fix modify QP checking of "current QP state" attribute
IPoIB: Fix multicast race between canceling and completing
IPoIB: Clean up if posting receives fails
IB/mthca: Use an enum for HCA page size
...
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] Fix cosmetic typo in asm/irq.h
[ARM] 3367/1: CLCD mode no longer supported on the RealView boards
[ARM] 3366/1: Allow the 16bpp mode configuration in the CLCD control register
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev: (112 commits)
[libata] sata_mv: fix irq port status usage
[PATCH] libata: move IDENTIFY info printing from ata_dev_read_id() to ata_dev_configure()
[PATCH] libata: use local *id instead of dev->id in ata_dev_configure()
[PATCH] libata: check Word 88 validity in ata_id_xfer_mask()
[PATCH] libata: fix class handling in ata_bus_probe()
[PATCH] ahci: enable prefetching for PACKET commands
libata: turn on ATAPI by default
[PATCH] sata_sil24: lengthen softreset timeout
[PATCH] sata_sil24: exit early from softreset if SStatus reports no device
[PATCH] libata: fix missing classes[] initialization in ata_bus_probe()
[PATCH] libata: kill unused xfer_mode functions
[PATCH] libata: reimplement ata_set_mode() using xfer_mask helpers
[PATCH] libata: use xfer_mask helpers in ata_dev_set_mode()
[PATCH] libata: use ata_id_xfermask() in ata_dev_configure()
[PATCH] libata: add xfer_mask handling functions
[PATCH] libata: improve xfer mask constants and update ata_mode_string()
[PATCH] libata: rename ATA_FLAG_FLUSH_PIO_TASK to ATA_FLAG_FLUSH_PORT_TASK
[PATCH] libata: kill unused pio_task and packet_task
[PATCH] libata: convert pio_task and packet_task to port_task
[PATCH] libata: implement port_task
...
This merges the DVB tree, but fixes up the history that had gotten
screwed up by a broken commit.
The history is fixed up by re-doing the commit properly (taking the
resolve from the final result of the original), and then cherry-picking
the commits that followed the broken merge.
* dvb: (190 commits)
V4L/DVB (3545): Fixed no_overlay option and quirks on saa7134 driver
V4L/DVB (3543): Fix Makefile to adapt to bt8xx/ conversion
V4L/DVB (3538): Bt8xx documentation update
V4L/DVB (3537a): Whitespace cleanup
V4L/DVB (3533): Add WSS (wide screen signalling) module parameters
V4L/DVB (3532): Moved duplicated code of ALPS BSRU6 tuner to a standalone file.
V4L/DVB (3530): Kconfig: remove VIDEO_AUDIO_DECODER
V4L/DVB (3529): Kconfig: add menu items for cs53l32a and wm8775 A/D converters
V4L/DVB (3528): Kconfig: fix ATSC frontend menu item names by manufacturer
V4L/DVB (3527): VIDEO_CPIA2 must depend on USB
V4L/DVB (3525): Kconfig: remove VIDEO_DECODER
V4L/DVB (3524): Kconfig: add menu items for saa7115 and saa7127
V4L/DVB (3494): Kconfig: select VIDEO_MSP3400 to build msp3400.ko
V4L/DVB (3522): Fixed a trouble with other PAL standards
V4L/DVB (3521): Avoid warnings at video-buf.c
V4L/DVB (3514): SAA7113 doesn't have auto std chroma detection mode
V4L/DVB (3513): Remove saa711x driver
V4L/DVB (3509): Make a needlessly global function static.
V4L/DVB (3506): Cinergy T2 dmx cleanup on disconnect
V4L/DVB (3504): Medion 7134: Autodetect second bridge chip
...
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some chipsets have several problems when pci to pci transfers are activated
on overlay mode. the option no_overlay allows disabling such feature of
the driver, in favor of keeping the system stable.
The default is to use pcipci_fail flag defined on drivers/pci/quirks.c.
It also allows the user to override it by forcing disable overlay or forcing
enable. Forcing enable may generate PCI transfer corruption, including disk
mass corruption, so should be used with care.
Added a text description to this option and make messages looks the same at
both bttv and saa7134 drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add wss_cfg_4_3 and wss_cfg_16_9 configuration options.
Firmware 2623 or later required.
Both parameters are bit masks:
- bit 15: disable WSS
- bit 14: send short WSS burst, then turn off WSS
- bit 13..0: WSS bits as specified by the standard
These parameters are useful if you own a broken tv set which
does not handle wss correctly.
Default settings:
- wss_cfg_4_3: 0x4008
- wss_cfg_16_9: 0x0007
These should work with most devices.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Moved duplicated code of ALPS BSRU6 tuner to a standalone file.
Modified av7110 and budget drivers to include the new file.
Signed-off-by: Perceval Anichini <perceval.anichini@streamvision.fr>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- removed VIDEO_AUDIO_DECODER Kconfig menu item.
VIDEO_MSP3400, VIDEO_CS53L32A and VIDEO_WM8775 now
each have their own menu items.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- created Kconfig item, VIDEO_CS53L32A, for the cs53l32a module which supports
the Cirrus Logic CS53L32A Low Voltage Stereo A/D Converter.
- created Kconfig item, VIDEO_WM8775, for the wm8775 module which supports
the Wolfson Microelectronics WM8775 high performance stereo A/D Converter.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Corrected typo for NxtWave NXT200X
- Added "Oren" manufacturer name to menu items for OR51132 and OR51211
- Removed "(pcHDTV HDx000 card)" from Oren frontends menu item names,
This isn't necessary, as these frontends are selected by the card drivers,
build configuration (DVB_BT8XX and VIDEO_CX88_DVB).
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
CONFIG_VIDEO_CPIA2=y, CONFIG_USB=n results in the following compile
<-- snip -->
...
LD .tmp_vmlinux1
drivers/built-in.o: In function `set_alternate':cpia2_usb.c:(.text+0x443aa2): undefined reference to `usb_set_interface'
drivers/built-in.o: In function `cpia2_usb_stream_resume': undefined reference to `usb_alloc_urb'
drivers/built-in.o: In function `cpia2_usb_stream_resume': undefined reference to `usb_submit_urb'
drivers/built-in.o: In function `cpia2_usb_stream_pause': undefined reference to `usb_kill_urb'
drivers/built-in.o: In function `cpia2_usb_stream_pause': undefined reference to `usb_free_urb'
drivers/built-in.o: In function `cpia2_usb_disconnect':cpia2_usb.c:(.text+0x443e14): undefined reference to `usb_driver_release_interface'
drivers/built-in.o: In function `cpia2_usb_transfer_cmd': undefined reference to `usb_control_msg'
drivers/built-in.o: In function `cpia2_usb_transfer_cmd': undefined reference to `usb_control_msg'
drivers/built-in.o: In function `cpia2_usb_complete':cpia2_usb.c:(.text+0x444836): undefined reference to `usb_submit_urb'
drivers/built-in.o: In function `cpia2_usb_cleanup': undefined reference to `usb_deregister'
drivers/built-in.o: In function `cpia2_usb_init': undefined reference to `usb_register_driver'
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
