Speculative delayed allocation beyond EOF near the maximum supported
file offset can result in creating delalloc extents beyond
mp->m_maxioffset (8EB). These can never be trimmed during
xfs_free_eof_blocks() because they are beyond mp->m_maxioffset, and
that results in assert failures in xfs_fs_destroy_inode() due to
delalloc blocks still being present. xfstests 071 exposes this
problem.
Limit speculative delalloc to mp->m_maxioffset to avoid this
problem.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
When we are doing speculative delayed allocation beyond EOF,
conversion of the region allocated beyond EOF is dependent on the
largest free space extent available. If the largest free extent is
smaller than the delalloc range, then after allocation we leave
a delalloc extent that starts beyond EOF. This extent cannot *ever*
be converted by flushing data, and so will remain there until either
the EOF moves into the extent or it is truncated away.
Hence if xfs_getbmap() runs on such an inode and is asked to return
extents beyond EOF, it will assert fail on this extent even though
there is nothing xfs_getbmap() can do to convert it to a real
extent. Hence we should simply report these delalloc extents rather
than assert that there should be none.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Often mounting small filesystem with small logs will emit a warning
such as:
XFS (vdb): Invalid block length (0x2000) for buffer
during log recovery. This causes tests to randomly fail because this
output causes the clean filesystem checks on test completion to
think the filesystem is inconsistent.
The cause of the error is simply that log recovery is asking for a
buffer size that is larger than the log when zeroing the tail. This
is because the buffer size is rounded up, and if the right head and
tail conditions exist then the buffer size can be larger than the log.
Limit the variable size xlog_get_bp() callers to requesting buffers
smaller than the log.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
When a partial write inside EOF fails, it can leave delayed
allocation blocks lying around because they don't get punched back
out. This leads to assert failures like:
XFS: Assertion failed: XFS_FORCED_SHUTDOWN(ip->i_mount) || ip->i_delayed_blks == 0, file: fs/xfs/xfs_super.c, line: 847
when evicting inodes from the cache. This can be trivially triggered
by xfstests 083, which takes between 5 and 15 executions on a 512
byte block size filesystem to trip over this. Debugging shows a
failed write due to ENOSPC calling xfs_vm_write_failed such as:
[ 5012.329024] ino 0xa0026: vwf to 0x17000, sze 0x1c85ae
and no action is taken on it. This leaves behind a delayed
allocation extent that has no page covering it and no data in it:
[ 5015.867162] ino 0xa0026: blks: 0x83 delay blocks 0x1, size 0x2538c0
[ 5015.868293] ext 0: off 0x4a, fsb 0x50306, len 0x1
[ 5015.869095] ext 1: off 0x4b, fsb 0x7899, len 0x6b
[ 5015.869900] ext 2: off 0xb6, fsb 0xffffffffe0008, len 0x1
^^^^^^^^^^^^^^^
[ 5015.871027] ext 3: off 0x36e, fsb 0x7a27, len 0xd
[ 5015.872206] ext 4: off 0x4cf, fsb 0x7a1d, len 0xa
So the delayed allocation extent is one block long at offset
0x16c00. Tracing shows that a bigger write:
xfs_file_buffered_write: size 0x1c85ae offset 0x959d count 0x1ca3f ioflags
allocates the block, and then fails with ENOSPC trying to allocate
the last block on the page, leading to a failed write with stale
delalloc blocks on it.
Because we've had an ENOSPC when trying to allocate 0x16e00, it
means that we are never goinge to call ->write_end on the page and
so the allocated new buffer will not get marked dirty or have the
buffer_new state cleared. In other works, what the above write is
supposed to end up with is this mapping for the page:
+------+------+------+------+------+------+------+------+
UMA UMA UMA UMA UMA UMA UND FAIL
where: U = uptodate
M = mapped
N = new
A = allocated
D = delalloc
FAIL = block we ENOSPC'd on.
and the key point being the buffer_new() state for the newly
allocated delayed allocation block. Except it doesn't - we're not
marking buffers new correctly.
That buffer_new() problem goes back to the xfs_iomap removal days,
where xfs_iomap() used to return a "new" status for any map with
newly allocated blocks, so that __xfs_get_blocks() could call
set_buffer_new() on it. We still have the "new" variable and the
check for it in the set_buffer_new() logic - except we never set it
now!
Hence that newly allocated delalloc block doesn't have the new flag
set on it, so when the write fails we cannot tell which blocks we
are supposed to punch out. WHy do we need the buffer_new flag? Well,
that's because we can have this case:
+------+------+------+------+------+------+------+------+
UMD UMD UMD UMD UMD UMD UND FAIL
where all the UMD buffers contain valid data from a previously
successful write() system call. We only want to punch the UND buffer
because that's the only one that we added in this write and it was
only this write that failed.
That implies that even the old buffer_new() logic was wrong -
because it would result in all those UMD buffers on the page having
set_buffer_new() called on them even though they aren't new. Hence
we shoul donly be calling set_buffer_new() for delalloc buffers that
were allocated (i.e. were a hole before xfs_iomap_write_delay() was
called).
So, fix this set_buffer_new logic according to how we need it to
work for handling failed writes correctly. Also, restore the new
buffer logic handling for blocks allocated via
xfs_iomap_write_direct(), because it should still set the buffer_new
flag appropriately for newly allocated blocks, too.
SO, now we have the buffer_new() being set appropriately in
__xfs_get_blocks(), we can detect the exact delalloc ranges that
we allocated in a failed write, and hence can now do a walk of the
buffers on a page to find them.
Except, it's not that easy. When block_write_begin() fails, it
unlocks and releases the page that we just had an error on, so we
can't use that page to handle errors anymore. We have to get access
to the page while it is still locked to walk the buffers. Hence we
have to open code block_write_begin() in xfs_vm_write_begin() to be
able to insert xfs_vm_write_failed() is the right place.
With that, we can pass the page and write range to
xfs_vm_write_failed() and walk the buffers on the page, looking for
delalloc buffers that are either new or beyond EOF and punch them
out. Handling buffers beyond EOF ensures we still handle the
existing case that xfs_vm_write_failed() handles.
Of special note is the truncate_pagecache() handling - that only
should be done for pages outside EOF - pages within EOF can still
contain valid, dirty data so we must not punch them out of the
cache.
That just leaves the xfs_vm_write_end() failure handling.
The only failure case here is that we didn't copy the entire range,
and generic_write_end() handles that by zeroing the region of the
page that wasn't copied, we don't have to punch out blocks within
the file because they are guaranteed to contain zeros. Hence we only
have to handle the existing "beyond EOF" case and don't need access
to the buffers on the page. Hence it remains largely unchanged.
Note that xfs_getbmap() can still trip over delalloc blocks beyond
EOF that are left there by speculative delayed allocation. Hence
this bug fix does not solve all known issues with bmap vs delalloc,
but it does fix all the the known accidental occurances of the
problem.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
xfs_is_delayed_page() checks to see if a page has buffers matching
the given IO type passed in. It does so by walking the buffer heads
on the page and checking if the state flags match the IO type.
However, the "acceptable" variable that is calculated is overwritten
every time a new buffer is checked. Hence if the first buffer on the
page is of the right type, this state is lost if the second buffer
is not of the correct type. This means that xfs_aops_discard_page()
may not discard delalloc regions when it is supposed to, and
xfs_convert_page() may not cluster IO as efficiently as possible.
This problem only occurs on filesystems with a block size smaller
than page size.
Also, rename xfs_is_delayed_page() to xfs_check_page_type() to
better describe what it is doing - it is not delalloc specific
anymore.
The problem was first noticed by Peter Watkins.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Doing background CIL flushes adds significant latency to whatever
async transaction that triggers it. To avoid blocking async
transactions on things like waiting for log buffer IO to complete,
move the CIL push off into a workqueue. By moving the push work
into a workqueue, we remove all the latency that the commit adds
from the foreground transaction commit path. This also means that
single threaded workloads won't do the CIL push procssing, leaving
them more CPU to do more async transactions.
To do this, we need to keep track of the sequence number we have
pushed work for. This avoids having many transaction commits
attempting to schedule work for the same sequence, and ensures that
we only ever have one push (background or forced) in progress at a
time. It also means that we don't need to take the CIL lock in write
mode to check for potential background push races, which reduces
lock contention.
To avoid potential issues with "smart" IO schedulers, don't use the
workqueue for log force triggered flushes. Instead, do them directly
so that the log IO is done directly by the process issuing the log
force and so doesn't get stuck on IO elevator queue idling
incorrectly delaying the log IO from the workqueue.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
xfs_trans_ail_delete_bulk() can be called from different contexts so
if the item is not in the AIL we need different shutdown for each
context. Pass in the shutdown method needed so the correct action
can be taken.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Queue delwri buffers on a local on-stack list instead of a per-buftarg one,
and write back the buffers per-process instead of by waking up xfsbufd.
This is now easily doable given that we have very few places left that write
delwri buffers:
- log recovery:
Only done at mount time, and already forcing out the buffers
synchronously using xfs_flush_buftarg
- quotacheck:
Same story.
- dquot reclaim:
Writes out dirty dquots on the LRU under memory pressure. We might
want to look into doing more of this via xfsaild, but it's already
more optimal than the synchronous inode reclaim that writes each
buffer synchronously.
- xfsaild:
This is the main beneficiary of the change. By keeping a local list
of buffers to write we reduce latency of writing out buffers, and
more importably we can remove all the delwri list promotions which
were hitting the buffer cache hard under sustained metadata loads.
The implementation is very straight forward - xfs_buf_delwri_queue now gets
a new list_head pointer that it adds the delwri buffers to, and all callers
need to eventually submit the list using xfs_buf_delwi_submit or
xfs_buf_delwi_submit_nowait. Buffers that already are on a delwri list are
skipped in xfs_buf_delwri_queue, assuming they already are on another delwri
list. The biggest change to pass down the buffer list was done to the AIL
pushing. Now that we operate on buffers the trylock, push and pushbuf log
item methods are merged into a single push routine, which tries to lock the
item, and if possible add the buffer that needs writeback to the buffer list.
This leads to much simpler code than the previous split but requires the
individual IOP_PUSH instances to unlock and reacquire the AIL around calls
to blocking routines.
Given that xfsailds now also handle writing out buffers, the conditions for
log forcing and the sleep times needed some small changes. The most
important one is that we consider an AIL busy as long we still have buffers
to push, and the other one is that we do increment the pushed LSN for
buffers that are under flushing at this moment, but still count them towards
the stuck items for restart purposes. Without this we could hammer on stuck
items without ever forcing the log and not make progress under heavy random
delete workloads on fast flash storage devices.
[ Dave Chinner:
- rebase on previous patches.
- improved comments for XBF_DELWRI_Q handling
- fix XBF_ASYNC handling in queue submission (test 106 failure)
- rename delwri submit function buffer list parameters for clarity
- xfs_efd_item_push() should return XFS_ITEM_PINNED ]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Instead of adding buffers to the delwri list as soon as they are logged,
even if they can't be written until commited because they are pinned
defer adding them to the delwri list until xfsaild pushes them. This
makes the code more similar to other log items and prepares for writing
buffers directly from xfsaild.
The complication here is that we need to fail buffers that were added
but not logged yet in xfs_buf_item_unpin, borrowing code from
xfs_bioerror.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Instead of writing the buffer directly from inside xfs_qm_dqflush return it
to the caller and let the caller decide what to do with the buffer. Also
remove the pincount check in xfs_qm_dqflush that all non-blocking callers
already implement and the now unused flags parameter and the XFS_DQ_IS_DIRTY
check that all callers already perform.
[ Dave Chinner: fixed build error cause by missing '{'. ]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Instead of writing the buffer directly from inside xfs_iflush return it to
the caller and let the caller decide what to do with the buffer. Also
remove the pincount check in xfs_iflush that all non-blocking callers already
implement and the now unused flags parameter.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
We already flush dirty inodes throug the AIL regularly, there is no reason
to have second thread compete with it and disturb the I/O pattern. We still
do write inodes when doing a synchronous reclaim from the shrinker or during
unmount for now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Now that we write back all metadata either synchronously or through
the AIL we can simply implement metadata freezing in terms of
emptying the AIL.
The implementation for this is fairly simply and straight-forward:
A new routine is added that asks the xfsaild to push the AIL to the
end and waits for it to complete and send a wakeup. The routine will
then loop if the AIL is not actually empty, and continue to do so
until the AIL is compeltely empty.
We keep an inode reclaim pass in the freeze process to avoid having
memory pressure have to reclaim inodes that require dirtying the
filesystem to be reclaimed after the freeze has completed. This
means we can also treat unmount in the exact same way as freeze.
As an upside we can now remove the radix tree based inode writeback
and xfs_unmountfs_writesb.
[ Dave Chinner:
- Cleaned up commit message.
- Added inode reclaim passes back into freeze.
- Cleaned up wakeup mechanism to avoid the use of a new
sleep counter variable. ]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Provide a variant of xlog_assign_tail_lsn that has the AIL lock already
held. By doing so we do an additional atomic_read + atomic_set under
the lock, which comes down to two instructions.
Switch xfs_trans_ail_update_bulk and xfs_trans_ail_delete_bulk to the
new version to reduce the number of lock roundtrips, and prepare for
a new addition that would require a third lock roundtrip in
xfs_trans_ail_delete_bulk. This addition is also the reason for
slightly rearranging the conditionals and relying on xfs_log_space_wake
for checking that the filesystem has been shut down internally.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
If a filesystem has been forced shutdown we are never going to write inodes
to disk, which means the inode items will stay in the AIL until we free
the inode. Currently that is not a problem, but a pending change requires us
to empty the AIL before shutting down the filesystem. In that case leaving
the inode in the AIL is lethal. Make sure to remove the log item from the AIL
to allow emptying the AIL on shutdown filesystems.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
If a filesystem has been forced shutdown we are never going to write dquots
to disk, which means the dquot items will stay in the AIL forever.
Currently that is not a problem, but a pending chance requires us to
empty the AIL before shutting down the filesystem, in which case this
behaviour is lethal. Make sure to remove the log item from the AIL
to allow emptying the AIL on shutdown filesystems.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Issuing a block device flush request in transaction context using GFP_KERNEL
directly can cause deadlocks due to memory reclaim recursion. Use GFP_NOFS to
avoid recursion from reclaim context.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
I've been seeing regular ASSERT failures in xfstests when running
fsstress based tests over the past month. xfs_getbmap() has been
failing this test:
XFS: Assertion failed: ((iflags & BMV_IF_DELALLOC) != 0) ||
(map[i].br_startblock != DELAYSTARTBLOCK), file: fs/xfs/xfs_bmap.c,
line: 5650
where it is encountering a delayed allocation extent after writing
all the dirty data to disk and then walking the extent map
atomically by holding the XFS_IOLOCK_SHARED to prevent new delayed
allocation extents from being created.
Test 083 on a 512 byte block size filesystem was used to reproduce
the problem, because it only had a 5s run timeand would usually fail
every 3-4 runs. This test is exercising ENOSPC behaviour by running
fsstress on a nearly full filesystem. The following trace extract
shows the final few events on the inode that tripped the assert:
xfs_ilock: flags ILOCK_EXCL caller xfs_setfilesize
xfs_setfilesize: isize 0x180000 disize 0x12d400 offset 0x17e200 count 7680
file size updated to 0x180000 by IO completion
xfs_ilock: flags ILOCK_EXCL caller xfs_iomap_write_delay
xfs_iext_insert: state idx 3 offset 3072 block 4503599627239432 count 1 flag 0 caller xfs_bmap_add_extent_hole_delay
xfs_get_blocks_alloc: size 0x180000 offset 0x180000 count 512 type startoff 0xc00 startblock -1 blockcount 0x1
xfs_ilock: flags ILOCK_EXCL caller __xfs_get_blocks
delalloc write, adding a single block at offset 0x180000
xfs_delalloc_enospc: isize 0x180000 disize 0x180000 offset 0x180200 count 512
ENOSPC trying to allocate a dellalloc block at offset 0x180200
xfs_ilock: flags ILOCK_EXCL caller xfs_iomap_write_delay
xfs_get_blocks_alloc: size 0x180000 offset 0x180200 count 512 type startoff 0xc00 startblock -1 blockcount 0x2
And succeeding on retry after flushing dirty inodes.
xfs_ilock: flags ILOCK_EXCL caller __xfs_get_blocks
xfs_delalloc_enospc: isize 0x180000 disize 0x180000 offset 0x180400 count 512
ENOSPC trying to allocate a dellalloc block at offset 0x180400
xfs_ilock: flags ILOCK_EXCL caller xfs_iomap_write_delay
xfs_delalloc_enospc: isize 0x180000 disize 0x180000 offset 0x180400 count 512
And failing the retry, giving a real ENOSPC error.
xfs_ilock: flags ILOCK_EXCL caller xfs_vm_write_failed
^^^^^^^^^^^^^^^^^^^
The smoking gun - the write being failed and cleaning up delalloc
blocks beyond EOF allocated by the failed write.
xfs_getattr:
xfs_ilock: flags IOLOCK_SHARED caller xfs_getbmap
xfs_ilock: flags ILOCK_SHARED caller xfs_ilock_map_shared
And that's where we died almost immediately afterwards.
xfs_bmapi_read() found delalloc extent beyond current file in memory
file size. Some debug I added to xfs_getbmap() showed the state just
before the assert failure:
ino 0x80e48: off 0xc00, fsb 0xffffffffffffffff, len 0x1, size 0x180000
start_fsb 0x106, end_fsb 0x638
ino flags 0x2 nex 0xd bmvcnt 0x555, len 0x3c58a6f23c0bf1, start 0xc00
ext 0: off 0x1fc, fsb 0x24782, len 0x254
ext 1: off 0x450, fsb 0x40851, len 0x30
ext 2: off 0x480, fsb 0xd99, len 0x1b8
ext 3: off 0x92f, fsb 0x4099a, len 0x3b
ext 4: off 0x96d, fsb 0x41844, len 0x98
ext 5: off 0xbf1, fsb 0x408ab, len 0xf
which shows that we found a single delalloc block beyond EOF (first
line of output) when we were returning the map for a length
somewhere around 10^16 bytes long (second line), and the on-disk
extents showed they didn't go past EOF (last lines).
Further debug added to xfs_vm_write_failed() showed this happened
when punching out delalloc blocks beyond the end of the file after
the failed write:
[ 132.606693] ino 0x80e48: vwf to 0x181000, sze 0x180000
[ 132.609573] start_fsb 0xc01, end_fsb 0xc08
It punched the range 0xc01 -> 0xc08, but the range we really need to
punch is 0xc00 -> 0xc07 (8 blocks from 0xc00) as this testing was
run on a 512 byte block size filesystem (8 blocks per page).
the punch from is 0xc00. So end_fsb is correct, but start_fsb is
wrong as we punch from start_fsb for (end_fsb - start_fsb) blocks.
Hence we are not punching the delalloc block beyond EOF in the case.
The fix is simple - it's a silly off-by-one mistake in calculating
the range. It's especially silly because the macro used to calculate
the start_fsb already takes into account the case where the inode
size is an exact multiple of the filesystem block size...
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
For the direct IO write path, we only really need the ilock to be taken in
exclusive mode during IO submission if we need to do extent allocation
instead of all the time.
Change the block mapping code to take the ilock in shared mode for the
initial block mapping, and only retake it exclusively when we actually
have to perform extent allocations. We were already dropping the ilock
for the transaction allocation, so this doesn't introduce new race windows.
Based on an earlier patch from Dave Chinner.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Instead of calling xfs_zero_eof with the ilock held only take it internally
for the minimall required critical section around xfs_bmapi_read. This
also requires changing the calling convention for xfs_zero_last_block
slightly. The actual zeroing operation is still serialized by the iolock,
which must be taken exclusively over the call to xfs_zero_eof.
We could in fact use a shared lock for the xfs_bmapi_read calls as long as
the extent list has been read in, but given that we already hold the iolock
exclusively there is little reason to micro optimize this further.
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
We do not need the ilock for most checks done in the beginning of
xfs_setattr_size. Replace the long critical section before starting the
transaction with a smaller one around xfs_zero_eof and an optional one
inside xfs_qm_dqattach that isn't entered unless using quotas. While
this isn't a big optimization for xfs_setattr_size itself it will allow
pushing the ilock into xfs_zero_eof itself later.
Signed-off-by: Christoph Hellwig <hch@lst.de>
We do not need the ilock for generic_write_checks and the i_size_read,
which are protected by i_mutex and/or iolock, so reduce the ilock
critical section to just the call to xfs_zero_eof.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Check if we actually need to attach a dquot before taking the ilock in
xfs_qm_dqattach. This avoid superflous lock roundtrips for the common cases
of quota support compiled in but not activated on a filesystem and an
inode that already has the dquots attached.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Because the mount process can run a quotacheck and consume lots of
inodes, we need to be able to run periodic inode reclaim during the
mount process. This will prevent running the system out of memory
during quota checks.
This essentially reverts 2bcf6e97, but that is safe to do now that
the quota sync code that was causing problems during long quotacheck
executions is now gone.
The reclaim work is currently protected from running during the
unmount process by a check against MS_ACTIVE. Unfortunately, this
also means that the reclaim work cannot run during mount. The
unmount process should stop the reclaim cleanly before freeing
anything that the reclaim work depends on, so there is no need to
have this guard in place.
Also, the inode reclaim work is demand driven, so there is no need
to start it immediately during mount. It will be started the moment
an inode is queued for reclaim, so qutoacheck will trigger it just
fine.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Check if the project quota is running or not before performing
xfs_qm_statvfs(), just return if not. Otherwise the ASSERT
XFS_IS_QUOTA_RUNNING in xfs_qm_dqget will be popped.
Signed-off-by: Jie Liu <jeff.liu@oracle.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
xfs-masters@oss.sgi.com will be retired in favor of xfs@oss.sgi.com
sometime soon.
Signed-off-by: Ben Myers <bpm@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Two more small fixes:
- Now we have users for it that aren't running Android it turns out that
regcache_sync_region() is much more useful to drivers if it's exported
for use by modules. Who knew?
- Make sure we don't divide by zero when doing debugfs dumps of rbtrees,
not visible up until now because everything was providing at least
some cache on startup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=qm1Q
-----END PGP SIGNATURE-----
Merge tag 'regmap-3.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull two more small regmap fixes from Mark Brown:
- Now we have users for it that aren't running Android it turns out
that regcache_sync_region() is much more useful to drivers if it's
exported for use by modules. Who knew?
- Make sure we don't divide by zero when doing debugfs dumps of
rbtrees, not visible up until now because everything was providing at
least some cache on startup.
* tag 'regmap-3.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: prevent division by zero in rbtree_show
regmap: Export regcache_sync_region()
Pull a few KVM fixes from Avi Kivity:
"A bunch of powerpc KVM fixes, a guest and a host RCU fix (unrelated),
and a small build fix."
* 'kvm-updates/3.4' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: Resolve RCU vs. async page fault problem
KVM: VMX: vmx_set_cr0 expects kvm->srcu locked
KVM: PMU: Fix integer constant is too large warning in kvm_pmu_set_msr()
KVM: PPC: Book3S: PR: Fix preemption
KVM: PPC: Save/Restore CR over vcpu_run
KVM: PPC: Book3S HV: Save and restore CR in __kvmppc_vcore_entry
KVM: PPC: Book3S HV: Fix kvm_alloc_linear in case where no linears exist
KVM: PPC: Book3S: Compile fix for ppc32 in HIOR access code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAk99uBgACgkQGkmNcg7/o7hglwCgqi6CE7i5gyneNYBn2ocRps4O
y1UAoMSIscO6YWcHPuxOiNBbJYUy/jMI
=SEO8
-----END PGP SIGNATURE-----
Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh
Pull SuperH fixes from Paul Mundt.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
sh: fix clock-sh7757 for the latest sh_mobile_sdhi driver
serial: sh-sci: use serial_port_in/out vs sci_in/out.
sh: vsyscall: Fix up .eh_frame generation.
sh: dma: Fix up device attribute mismatch from sysdev fallout.
sh: dwarf unwinder depends on SHcompact.
sh: fix up fallout from system.h disintegration.
Pull security layer fixlet from James Morris.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
sysctl: fix write access to dmesg_restrict/kptr_restrict
Pull ACPI & Power Management patches from Len Brown:
"Two fixes for cpuidle merge-window changes, plus a URL fix in
MAINTAINERS"
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
MAINTAINERS: Update git url for ACPI
cpuidle: Fix panic in CPU off-lining with no idle driver
ACPI processor: Use safe_halt() rather than halt() in acpi_idle_play_dead()
Pull target fixes from Nicholas Bellinger:
"Pull two tcm_fc fabric related fixes for -rc2:
Note that both have been CC'ed to stable, and patch #1 is the
important one that addresses a memory corruption bug related to FC
exchange timeouts + command abort.
Thanks again to MDR for tracking down this issue!"
* '3.4-rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
tcm_fc: Do not free tpg structure during wq allocation failure
tcm_fc: Add abort flag for gracefully handling exchange timeout
Avoid freeing a registered tpg structure if an alloc_workqueue call
fails. This fixes a bug where the failure was leaking memory associated
with se_portal_group setup during the original core_tpg_register() call.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Acked-by: Kiran Patil <Kiran.patil@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Add abort flag and use it to terminate processing when an exchange
is timed out or is reset. The abort flag is used in place of the
transport_generic_free_cmd function call in the reset and timeout
cases, because calling that function in that context would free
memory that was in use. The aborted flag allows the lifetime to
be managed in a more normal way, while truncating the processing.
This change eliminates a source of memory corruption which
manifested in a variety of ugly ways.
(nab: Drop unused struct fc_exch *ep in ft_recv_seq)
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Acked-by: Kiran Patil <Kiran.patil@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull arch/tile bug fixes from Chris Metcalf:
"This includes Paul Gortmaker's change to fix the <asm/system.h>
disintegration issues on tile, a fix to unbreak the tilepro ethernet
driver, and a backlog of bugfix-only changes from internal Tilera
development over the last few months.
They have all been to LKML and on linux-next for the last few days.
The EDAC change to MAINTAINERS is an oddity but discussion on the
linux-edac list suggested I ask you to pull that change through my
tree since they don't have a tree to pull edac changes from at the
moment."
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile: (39 commits)
drivers/net/ethernet/tile: fix netdev_alloc_skb() bombing
MAINTAINERS: update EDAC information
tilepro ethernet driver: fix a few minor issues
tile-srom.c driver: minor code cleanup
edac: say "TILEGx" not "TILEPro" for the tilegx edac driver
arch/tile: avoid accidentally unmasking NMI-type interrupt accidentally
arch/tile: remove bogus performance optimization
arch/tile: return SIGBUS for addresses that are unaligned AND invalid
arch/tile: fix finv_buffer_remote() for tilegx
arch/tile: use atomic exchange in arch_write_unlock()
arch/tile: stop mentioning the "kvm" subdirectory
arch/tile: export the page_home() function.
arch/tile: fix pointer cast in cacheflush.c
arch/tile: fix single-stepping over swint1 instructions on tilegx
arch/tile: implement panic_smp_self_stop()
arch/tile: add "nop" after "nap" to help GX idle power draw
arch/tile: use proper memparse() for "maxmem" options
arch/tile: fix up locking in pgtable.c slightly
arch/tile: don't leak kernel memory when we unload modules
arch/tile: fix bug in delay_backoff()
...
* one is a workaround that will be removed in v3.5 with proper fix in the tip/x86 tree,
* the other is to fix drivers to load on PV (a previous patch made them only
load in PVonHVM mode).
The rest are just minor fixes in the various drivers and some cleanup in the
core code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPfyVUAAoJEFjIrFwIi8fJUjUH/jbY5JavRqSlNELZW2A4Ta76
8p00LqLHw/C56iHZcWKke8mqtWNb+ZfcQt7ZYcxDIYa4QWBL28x0OLAO2tOBIt37
ZjYESWSdFJaJvmpADluWtFyGyZ9TYJllDTBm/jWj1ZtKSZvR1YkhuMXCS0f4AmGQ
xFzSWJZUDdiOAqpN+VQD8wP00gfR8knQLg16XE2fvFdQo4XwpCtqLfHV/5pMMGdy
Cs/ep6rq/7cdv/nshKOcBnw7RW8l3Xoi/28ht8k3DvAQ2VtFq1Tugv2G9pcCHwQG
DIBkB3SOU6/v6P5at5+egKS5xR1fJetCWlkMd8kkbcdz2NPI4UDMkvOW6Q8yQls=
=6Ve+
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull xen fixes from Konrad Rzeszutek Wilk:
"Two fixes for regressions:
* one is a workaround that will be removed in v3.5 with proper fix in
the tip/x86 tree,
* the other is to fix drivers to load on PV (a previous patch made
them only load in PVonHVM mode).
The rest are just minor fixes in the various drivers and some cleanup
in the core code."
* tag 'stable/for-linus-3.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pcifront: avoid pci_frontend_enable_msix() falsely returning success
xen/pciback: fix XEN_PCI_OP_enable_msix result
xen/smp: Remove unnecessary call to smp_processor_id()
xen/x86: Workaround 'x86/ioapic: Add register level checks to detect bogus io-apic entries'
xen: only check xen_platform_pci_unplug if hvm
The major fixes here are:
* Disable use of MSI in sdhci-pci, which caused multiple chipsets to
stop working in 3.4-rc1. I'll wait to turn this on again until we
have a chipset whitelist for it.
* Fix a libertas SDIO powered-resume regression introduced in 3.3;
thanks to Neil Brown and Rafael Wysocki for this fix.
* Fix module reloading on omap_hsmmc.
* Stop trusting the spec/card's specified maximum data timeout length,
and use three seconds instead. Previously we used 300ms.
Also cleanups and fixes for s3c, atmel, sh_mmcif and omap_hsmmc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=CCKD
-----END PGP SIGNATURE-----
Merge tag 'mmc-fixes-for-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC fixes from Chris Ball:
- Disable use of MSI in sdhci-pci, which caused multiple chipsets to
stop working in 3.4-rc1. I'll wait to turn this on again until we
have a chipset whitelist for it.
- Fix a libertas SDIO powered-resume regression introduced in 3.3;
thanks to Neil Brown and Rafael Wysocki for this fix.
- Fix module reloading on omap_hsmmc.
- Stop trusting the spec/card's specified maximum data timeout length,
and use three seconds instead. Previously we used 300ms.
Also cleanups and fixes for s3c, atmel, sh_mmcif and omap_hsmmc.
* tag 'mmc-fixes-for-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (28 commits)
mmc: use really long write timeout to deal with crappy cards
mmc: sdhci-dove: Fix compile error by including module.h
mmc: Prevent 1.8V switch for SD hosts that don't support UHS modes.
Revert "mmc: sdhci-pci: Add MSI support"
Revert "mmc: sdhci-pci: add quirks for broken MSI on O2Micro controllers"
mmc: core: fix power class selection
mmc: omap_hsmmc: fix module re-insertion
mmc: omap_hsmmc: convert to module_platform_driver
mmc: omap_hsmmc: make it behave well as a module
mmc: omap_hsmmc: trivial cleanups
mmc: omap_hsmmc: context save after enabling runtime pm
mmc: omap_hsmmc: use runtime put sync in probe error patch
mmc: sdio: Use empty system suspend/resume callbacks at the bus level
mmc: bus: print bus speed mode of UHS-I card
mmc: sdhci-pci: add quirks for broken MSI on O2Micro controllers
mmc: sh_mmcif: Simplify calculation of mmc->f_min
mmc: sh_mmcif: mmc->f_max should be half of the bus clock
mmc: sh_mmcif: double clock speed
mmc: block: Remove use of mmc_blk_set_blksize
mmc: atmel-mci: add support for odd clock dividers
...
I have a new optimized x86 "strncpy_from_user()" that will use these
same helper functions for all the same reasons the name lookup code uses
them. This is preparation for that.
This moves them into an architecture-specific header file. It's
architecture-specific for two reasons:
- some of the functions are likely to want architecture-specific
implementations. Even if the current code happens to be "generic" in
the sense that it should work on any little-endian machine, it's
likely that the "multiply by a big constant and shift" implementation
is less than optimal for an architecture that has a guaranteed fast
bit count instruction, for example.
- I expect that if architectures like sparc want to start playing
around with this, we'll need to abstract out a few more details (in
particular the actual unaligned accesses). So we're likely to have
more architecture-specific stuff if non-x86 architectures start using
this.
(and if it turns out that non-x86 architectures don't start using
this, then having it in an architecture-specific header is still the
right thing to do, of course)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a NULL pointer dereference panic in cpuidle_play_dead() during
CPU off-lining when no cpuidle driver is registered. A cpuidle
driver may be registered at boot-time based on CPU type. This patch
allows an off-lined CPU to enter HLT-based idle in this condition.
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Cc: Boris Ostrovsky <boris.ostrovsky@amd.com>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Tested-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Pull networking updates from David Miller:
1) Fix inaccuracies in network driver interface documentation, from Ben
Hutchings.
2) Fix handling of negative offsets in BPF JITs, from Jan Seiffert.
3) Compile warning, locking, and refcounting fixes in netfilter's
xt_CT, from Pablo Neira Ayuso.
4) phonet sendmsg needs to validate user length just like any other
datagram protocol, fix from Sasha Levin.
5) Ipv6 multicast code uses wrong loop index, from RongQing Li.
6) Link handling and firmware fixes in bnx2x driver from Yaniv Rosner
and Yuval Mintz.
7) mlx4 erroneously allocates 4 pages at a time, regardless of page
size, fix from Thadeu Lima de Souza Cascardo.
8) SCTP socket option wasn't extended in a backwards compatible way,
fix from Thomas Graf.
9) Add missing address change event emissions to bonding, from Shlomo
Pongratz.
10) /proc/net/dev regressed because it uses a private offset to track
where we are in the hash table, but this doesn't track the offset
pullback that the seq_file code does resulting in some entries being
missed in large dumps.
Fix from Eric Dumazet.
11) do_tcp_sendpage() unloads the send queue way too fast, because it
invokes tcp_push() when it shouldn't. Let the natural sequence
generated by the splice paths, and the assosciated MSG_MORE
settings, guide the tcp_push() calls.
Otherwise what goes out of TCP is spaghetti and doesn't batch
effectively into GSO/TSO clusters.
From Eric Dumazet.
12) Once we put a SKB into either the netlink receiver's queue or a
socket error queue, it can be consumed and freed up, therefore we
cannot touch it after queueing it like that.
Fixes from Eric Dumazet.
13) PPP has this annoying behavior in that for every transmit call it
immediately stops the TX queue, then calls down into the next layer
to transmit the PPP frame.
But if that next layer can take it immediately, it just un-stops the
TX queue right before returning from the transmit method.
Besides being useless work, it makes several facilities unusable, in
particular things like the equalizers. Well behaved devices should
only stop the TX queue when they really are full, and in PPP's case
when it gets backlogged to the downstream device.
David Woodhouse therefore fixed PPP to not stop the TX queue until
it's downstream can't take data any more.
14) IFF_UNICAST_FLT got accidently lost in some recent stmmac driver
changes, re-add. From Marc Kleine-Budde.
15) Fix link flaps in ixgbe, from Eric W. Multanen.
16) Descriptor writeback fixes in e1000e from Matthew Vick.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits)
net: fix a race in sock_queue_err_skb()
netlink: fix races after skb queueing
doc, net: Update ndo_start_xmit return type and values
doc, net: Remove instruction to set net_device::trans_start
doc, net: Update netdev operation names
doc, net: Update documentation of synchronisation for TX multiqueue
doc, net: Remove obsolete reference to dev->poll
ethtool: Remove exception to the requirement of holding RTNL lock
MAINTAINERS: update for Marvell Ethernet drivers
bonding: properly unset current_arp_slave on slave link up
phonet: Check input from user before allocating
tcp: tcp_sendpages() should call tcp_push() once
ipv6: fix array index in ip6_mc_add_src()
mlx4: allocate just enough pages instead of always 4 pages
stmmac: re-add IFF_UNICAST_FLT for dwmac1000
bnx2x: Clear MDC/MDIO warning message
bnx2x: Fix BCM57711+BCM84823 link issue
bnx2x: Clear BCM84833 LED after fan failure
bnx2x: Fix BCM84833 PHY FW version presentation
bnx2x: Fix link issue for BCM8727 boards.
...
The original XenoLinux code has always had things this way, and for
compatibility reasons (in particular with a subsequent pciback
adjustment) upstream Linux should behave the same way (allowing for two
distinct error indications to be returned by the backend).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Prior to 2.6.19 and as of 2.6.31, pci_enable_msix() can return a
positive value to indicate the number of vectors (less than the amount
requested) that can be set up for a given device. Returning this as an
operation value (secondary result) is fine, but (primary) operation
results are expected to be negative (error) or zero (success) according
to the protocol. With the frontend fixed to match the XenoLinux
behavior, the backend can now validly return zero (success) here,
passing the upper limit on the number of vectors in op->value.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
There is an extra and unnecessary call to smp_processor_id()
in cpu_bringup(). Remove it.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The above mentioned patch checks the IOAPIC and if it contains
-1, then it unmaps said IOAPIC. But under Xen we get this:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000040
IP: [<ffffffff8134e51f>] xen_irq_init+0x1f/0xb0
PGD 0
Oops: 0002 [#1] SMP
CPU 0
Modules linked in:
Pid: 1, comm: swapper/0 Not tainted 3.2.10-3.fc16.x86_64 #1 Dell Inc. Inspiron
1525 /0U990C
RIP: e030:[<ffffffff8134e51f>] [<ffffffff8134e51f>] xen_irq_init+0x1f/0xb0
RSP: e02b: ffff8800d42cbb70 EFLAGS: 00010202
RAX: 0000000000000000 RBX: 00000000ffffffef RCX: 0000000000000001
RDX: 0000000000000040 RSI: 00000000ffffffef RDI: 0000000000000001
RBP: ffff8800d42cbb80 R08: ffff8800d6400000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 00000000ffffffef
R13: 0000000000000001 R14: 0000000000000001 R15: 0000000000000010
FS: 0000000000000000(0000) GS:ffff8800df5fe000(0000) knlGS:0000000000000000
CS: e033 DS: 0000 ES: 0000 CR0:000000008005003b
CR2: 0000000000000040 CR3: 0000000001a05000 CR4: 0000000000002660
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process swapper/0 (pid: 1, threadinfo ffff8800d42ca000, task ffff8800d42d0000)
Stack:
00000000ffffffef 0000000000000010 ffff8800d42cbbe0 ffffffff8134f157
ffffffff8100a9b2 ffffffff8182ffd1 00000000000000a0 00000000829e7384
0000000000000002 0000000000000010 00000000ffffffff 0000000000000000
Call Trace:
[<ffffffff8134f157>] xen_bind_pirq_gsi_to_irq+0x87/0x230
[<ffffffff8100a9b2>] ? check_events+0x12+0x20
[<ffffffff814bab42>] xen_register_pirq+0x82/0xe0
[<ffffffff814bac1a>] xen_register_gsi.part.2+0x4a/0xd0
[<ffffffff814bacc0>] acpi_register_gsi_xen+0x20/0x30
[<ffffffff8103036f>] acpi_register_gsi+0xf/0x20
[<ffffffff8131abdb>] acpi_pci_irq_enable+0x12e/0x202
[<ffffffff814bc849>] pcibios_enable_device+0x39/0x40
[<ffffffff812dc7ab>] do_pci_enable_device+0x4b/0x70
[<ffffffff812dc878>] __pci_enable_device_flags+0xa8/0xf0
[<ffffffff812dc8d3>] pci_enable_device+0x13/0x20
The reason we are dying is b/c the call acpi_get_override_irq() is used,
which returns the polarity and trigger for the IRQs. That function calls
mp_find_ioapics to get the 'struct ioapic' structure - which along with the
mp_irq[x] is used to figure out the default values and the polarity/trigger
overrides. Since the mp_find_ioapics now returns -1 [b/c the IOAPIC is filled
with 0xffffffff], the acpi_get_override_irq() stops trying to lookup in the
mp_irq[x] the proper INT_SRV_OVR and we can't install the SCI interrupt.
The proper fix for this is going in v3.5 and adds an x86_io_apic_ops
struct so that platforms can override it. But for v3.4 lets carry this
work-around. This patch does that by providing a slightly different variant
of the fake IOAPIC entries.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
commit b9136d207f08
xen: initialize platform-pci even if xen_emul_unplug=never
breaks blkfront/netfront by not loading them because of
xen_platform_pci_unplug=0 and it is never set for PV guest.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
As soon as an skb is queued into socket error queue, another thread
can consume it, so we are not allowed to reference skb anymore, or risk
use after free.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
