This patch updates description of fam15h_power driver, its scope is
extended to family 16h processsors.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On Carrizo and later platforms, running_avg_capture bit field is
extended to 4:31 (28 bits) from 4:25.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
We rename fam15h_power_is_internal_node0() function to
should_load_on_this_node(), because it may not be node0 from KV and
on, and they are single-node processors.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
AMD Carrizo(Fam15h, M60h) processors can report power1_crit
(ProcessorPwrWatts) and power1_input (CurrPwrWatts) values.
And this patch adds support for CZ.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some of the LTC chips supported by this driver have to be polled
to ensure that they are ready to accept commands.
Signed-off-by: Michael Jones <mike@proclivis.com>
[Guenter Roeck: simplifications and formatting changes]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
PMBus controllers optionally support PEC. Configure the driver
to use it if available to improve operational security.
Suggested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC3886 is a is a dual PolyPhase DC/DC synchronous step-down switching
regulator controller. It is mostly command compatible to LTC3883,
but supports two phases instead of one.
Suggested-by: Michael Jones <mike@proclivis.com>
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC2980 and LTM2987 are command compatible to LTC2977. They consist of
two LTC2977 on a single die, and are instantiated as two separate chips,
each supporting eight channels.
Suggested-by: Michael Jones <mike@proclivis.com>
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add additional chip ID for an older revision of LTC2978, as well
as two chip IDs for LTC3882. Turns out the LTC3882 does support the
LTC2978_MFR_SPECIAL_ID register, and reading it returns its chip ID,
but the register is undocumented.
Suggested-by: Michael Jones <mike@proclivis.com>
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Per information from Linear Technologies, the ID mask is 12 bit
for all chips of this series. Use this mask to detect chips to ensure
that all chip revisions are detected.
Suggested-by: Michael Jones <mike@proclivis.com>
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The code used to determine historic low and high peaks is repeated
several times. Introduce helper functions to simplify it.
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It is becoming cumbersom to track per-chip feature support.
Introduce feature flag to simplify the code.
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC2975 is mostly compatible to LTC2974, but supports input current
and power measurement.
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Per datasheet, the chip ID for LTM4676 is 0x448x. This was observed
in real systems. In addition to that, chip ID 0x4401 was observed
as well. Research shows that the chip ID has been changed from 0x440x
to 0x448x in datasheet revision C. Add support for the additional chip ID.
Also add the chip ID for LTM4676A, which is functionally identical
to LTM4676.
Reported-by: Ananda Babu Nettam <anandab@juniper.net>
Cc: Ananda Babu Nettam <anandab@juniper.net>
Cc: Amit U Jain <amjain@juniper.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC3882 is mostly compatible with LTC3880. Major differences are that it
does not measure the input current, and it no longer supports LTC's legacy
mechanism to identify the chip.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Verifying the chip type is getting more complicated with new chips,
since not all chips support the same mechanism to read the chip type.
Move the code into a separate function to simplify adding support for
those chips.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This change sht15_reverse() to be generic bitrev8().
Signed-off-by: yalin wang <yalin.wang2010@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add device IDs and references for Texas Instruments TPS544B20, TPS544B25,
TPS544C20, and TPS544C25 to the generic PMBus driver.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX20751 is a multiphase power controller with internal buck converter.
It uses VR12.0 to report the output voltage. This requires an explicit
driver, since the VR version can not be auto-detected.
The chip supports a manufacturer specific command to fine-tune the output
voltage. This command is not currently supported.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the IT8732F. This chip is pretty similar to IT8721F,
with the main difference being that the ADC LSB is 10.9 mV instead of
12 mV.
Signed-off-by: Justin Maggard <jmaggard@netgear.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ADM1293 and ADM1294 are mostly compatible with other chips of the same
series, but have more configuration options. There are also some
differences in register details.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Introduce have_vout, have_vaux_status, have_pin_max, and have_uc_fault
to simplify adding support for new chips.
Also simplify error returns where appropriate to return immediately
on error.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Each new chip supported by the driver has a new set of coefficients,
making hard-coding coefficients more and more cumbersome. Introduce
a datastructure and table to simplify configuration.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pmbus_regulator_ops is not modified after initialized, so make it const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The pmbus_regulator_ops is for voltage regulators, so explicitly set
regulator type for better readability.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add f81768d (id 0x1210) currently found on Jetway motherboards.
It has 11 voltages but otherwise needed no special handling
in this driver.
Signed-off-by: George Joseph <george.joseph@fairview5.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The temperature value of Fintek F81866 is the same with
f71882fg. It located with 0x6c + 2*(nr), others located
with 0x6c + 2*(nr+1). We change the rule in f71882fg_probe(),
If type = f71858fg/f8000/f81866a. the temp_start will set to 0,
others are 1.
The F81866 over-temperature beep setting is not the same with
f71882fg too. They are using the same address 63H, but F81866 is
using bit 0/1/2 & 4/5/6, others are using bit 1/2/3 & 5/6/7,
So we copy from fxxxx_temp_beep_attr[] to f81866_temp_beep_attr
and change bit setting.
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add New Fintek SuperIO F81866(0x1010) & F71868(0x1106)
with H/W Monitor functions.
We increased F71882FG_MAX_INS from 9 to 10 to read
F71868 10 voltage sets.
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Added fan output control registers.
Modes of operation are PWM (default) and DC.
Introduced show_pwm, store_pwm, nct7802_pwm_attrs, nct7802_pwm_group.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull input subsystem fixes from Dmitry Torokhov:
"Just small ALPS and Elan touchpads, and other driver fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - add special check for fw_version 0x470f01 touchpad
Input: twl4030-vibra - fix ERROR: Bad of_node_put() warning
Input: alps - only Dell laptops have separate button bits for v2 dualpoint sticks
Input: axp20x-pek - add module alias
Input: turbografx - fix potential out of bound access
Pull MIPS fixes from Ralf Baechle:
"Another round of MIPS fixes for 4.2. No area does particularly stand
out but we have a two unpleasant ones:
- Kernel ptes are marked with a global bit which allows the kernel to
share kernel TLB entries between all processes. For this to work
both entries of an adjacent even/odd pte pair need to have the
global bit set. There has been a subtle race in setting the other
entry's global bit since ~ 2000 but it take particularly
pathological workloads that essentially do mostly vmalloc/vfree to
trigger this.
This pull request fixes the 64-bit case but leaves the case of 32
bit CPUs with 64 bit ptes unsolved for now. The unfixed cases
affect hardware that is not available in the field yet.
- Instruction emulation requires loading instructions from user space
but the current fast but simplistic approach will fail on pages
that are PROT_EXEC but !PROT_READ. For this reason we temporarily
do not permit this permission and will map pages with PROT_EXEC |
PROT_READ.
The remainder of this pull request is more or less across the field
and the short log explains them well"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Make set_pte() SMP safe.
MIPS: Replace add and sub instructions in relocate_kernel.S with addiu
MIPS: Flush RPS on kernel entry with EVA
Revert "MIPS: BCM63xx: Provide a plat_post_dma_flush hook"
MIPS: BMIPS: Delete unused Kconfig symbol
MIPS: Export get_c0_perfcount_int()
MIPS: show_stack: Fix stack trace with EVA
MIPS: do_mcheck: Fix kernel code dump with EVA
MIPS: SMP: Don't increment irq_count multiple times for call function IPIs
MIPS: Partially disable RIXI support.
MIPS: Handle page faults of executable but unreadable pages correctly.
MIPS: Malta: Don't reinitialise RTC
MIPS: unaligned: Fix build error on big endian R6 kernels
MIPS: Fix sched_getaffinity with MT FPAFF enabled
MIPS: Fix build with CONFIG_OF=y for non OF-enabled targets
CPUFREQ: Loongson2: Fix broken build due to incorrect include.
Pull btrfs fix from Chris Mason:
"We have a btrfs quota regression fix.
I merged this one on Thursday and have run it through tests against
current master.
Normally I wouldn't have sent this while you were finalizing rc6, but
I'm feeding mosquitoes in the adirondacks next week, so I wanted to
get this one out before leaving. I'll leave longer tests running and
check on things during the week, but I don't expect any problems"
* 'for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: qgroup: Fix a regression in qgroup reserved space.
Pull thermal management fixes from Zhang Rui:
"Specifics:
- fix an error that "weight_attr" sysfs attribute is not removed
while unbinding. From: Viresh Kumar.
- fix power allocator governor tracing to return the real request.
From Javi Merino.
- remove redundant owner assignment of hisi platform thermal driver.
From Krzysztof Kozlowski.
- a couple of small fixes of Exynos thermal driver. From Krzysztof
Kozlowski and Chanwoo Choi"
* 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: Drop owner assignment from platform_driver
thermal: exynos: Remove unused code related to platform_data on probe()
thermal: exynos: Add the dependency of CONFIG_THERMAL_OF instead of CONFIG_OF
thermal: exynos: Disable the regulator on probe failure
thermal: power_allocator: trace the real requested power
thermal: remove dangling 'weight_attr' device file
Adding software workaround for LLOCK/SCOND livelock
Fallout of a recent pt_regs update
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gFBX
-----END PGP SIGNATURE-----
Merge tag 'arc-v4.2-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"Here's a late pull request for accumulated ARC fixes which came out of
extended testing of the new ARCv2 port with LTP etc. llock/scond
livelock workaround has been reviewed by PeterZ. The changes look a
lot but I've crafted them into finer grained patches for better
tracking later.
I have some more fixes (ARC Futex backend) ready to go but those will
have to wait for tglx to return from vacation.
Summary:
- Enable a reduced config of HS38 (w/o div-rem, ll64...)
- Add software workaround for LLOCK/SCOND livelock
- Fallout of a recent pt_regs update"
* tag 'arc-v4.2-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARCv2: spinlock/rwlock/atomics: reduce 1 instruction in exponential backoff
ARC: Make pt_regs regs unsigned
ARCv2: spinlock/rwlock: Reset retry delay when starting a new spin-wait cycle
ARCv2: spinlock/rwlock/atomics: Delayed retry of failed SCOND with exponential backoff
ARC: LLOCK/SCOND based rwlock
ARC: LLOCK/SCOND based spin_lock
ARC: refactor atomic inline asm operands with symbolic names
Revert "ARCv2: STAR 9000837815 workaround hardware exclusive transactions livelock"
ARCv2: [axs103_smp] Reduce clk for Quad FPGA configs
ARCv2: Fix the peripheral address space detection
ARCv2: allow selection of page size for MMUv4
ARCv2: lib: memset: Don't assume 64-bit load/stores
ARCv2: lib: memcpy: Missing PREFETCHW
ARCv2: add knob for DIV_REV in Kconfig
ARC/time: Migrate to new 'set-state' interface
