To show information per interface, add a debugfs hardif structure
similar to the system in sysfs. Hard interface folders will be created
in "$debugfs/batman-adv/". Files are not yet added.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
With the new interface alternating, the first hop may send packets
in a round robin fashion to it's neighbors because it has multiple
valid routes built by the multi interface optimization. This patch
enables the feature if bonding is selected. Note that unlike the
bonding implemented before, this version is much simpler and may
even enable multi path routing to a certain degree.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The current OGM sending an aggregation functionality decides on
which interfaces a packet should be sent when it parses the forward
packet struct. However, with the network wide multi interface
optimization the outgoing interface is decided by the OGM processing
function.
This is reflected by moving the decision in the OGM processing function
and add the outgoing interface in the forwarding packet struct. This
practically implies that an OGM may be added multiple times (once per
outgoing interface), and this also affects aggregation which needs to
consider the outgoing interface as well.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
If the same interface is used for sending and receiving, there might be
throughput degradation on half-duplex interfaces such as WiFi. Add a
penalty if the same interface is used to reflect this problem in the
metric. At the same time, change the hop penalty from 30 to 15 so there
will be no change for single wifi mesh network. the effective hop
penalty will stay at 30 due to the new wifi penalty for these networks.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
For the network wide multi interface optimization there are different
routers for each outgoing interface (outgoing from the OGM perspective,
incoming for payload traffic). To reflect this, change the router and
associated data to a list of routers.
While at it, rename batadv_orig_node_get_router() to
batadv_orig_router_get() to follow the new naming scheme.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
For the network wide multi interface optimization it is required to save
metrics per outgoing interface in one neighbor. Therefore a new type is
introduced to keep interface-specific information. This also requires
some changes in access and list management.
The compare and equiv_or_better API calls are changed to take the
outgoing interface into consideration.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Remove bonding and interface alternating code - it will be replaced
by a new, network-wide multi interface optimization which enables
both bonding and interface alternating in a better way.
Keep the sysfs and find router function though, this will be needed
later.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Sabrina Dubroca says:
====================
alx: add statistics
Currently, the alx driver doesn't support statistics [1,2]. The
original alx driver [3] that Johannes Berg modified provided
statistics. This patch is an adaptation of the statistics code from
the original driver to the alx driver included in the kernel.
v4:
- modified the assignements of hw stats to netstats (Ben Hutchings)
- added comments to describe the stats fields (copied from atlx)
v3:
- renamed __alx_update_hw_stats to alx_update_hw_stats (Stephen Hemminger)
v2:
- use u64 instead of unsigned long (Ben Hutchings)
- implement ndo_get_stats64 instead of ndo_get_stats (Ben Hutchings)
- use EINVAL instead of ENOTSUPP (Ben Hutchings)
- add BUILD_BUG_ON to check the size of the stats (Johannes Berg, Ben
Hutchings)
- add a comment regarding persistence of the stats (Stephen Hemminger)
- align assignments in __alx_update_hw_stats
[1] https://bugzilla.kernel.org/show_bug.cgi?id=63401
[2] http://www.spinics.net/lists/netdev/msg245544.html
[3] https://github.com/mcgrof/alx
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to i40e and now i40evf.
Most notable is Jacob's patch to add PTP support to i40e.
Mitch cleans up additional memcpy's and use struct assignment instead.
Then fixes long lines to appease checkpatch.pl. Mitch then provides
a fix to keep us from spamming the log with confusing errors. If you
use ip to change the MAC address of a VF while the VF driver is loaded,
closing the VF interface or unloading the VF driver will cause the VF
driver to remove the MAC filter for its original (now invalid) MAC
address.
Jesse cleans up macros which are no longer needed or used.
I (Jeff) cleanup function header comments to ensure Doxygen/kdoc works
correctly to generate documentation without warnings.
Anjali fixes a bug where ethtool set-channels would return failure when
configuring only one Rx queue. Then fixes a bug where the driver was
erroneously exiting the driver unload path if one part of the unload
failed.
Shannon fixes if the IPV6EXADD but is set in the Rx descriptor status,
there was an optional extension header with an alternate IP address
detected and the hardware checksum was not handling the alternate IP
address correctly. Then adjusts the ITR max and min values to match
the hardware max value and recommended min value. Shannon makes sure
to clear the PXE mode after the adminq is initialized.
v2:
- fix patch 14 "i40e: enable PTP" to address Richard Cochran's spelling
catch and Ben Hutchings Kconfig, SIOCGHWTSTAMP and sizeof() suggestions
- added Paul Gortmaker's i40evf fix patch
v3:
- fix patch 14 "i40e: enable PTP" to address Ben Hutchings concerns about
a race with PTP init and cleanup and i40e_get_ts_info().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As of commit 7f12ad741a ("i40evf: transmit
and receive functionality") the s390 builds (allyesconfig) fail with:
drivers/net/ethernet/intel/i40evf/i40e_txrx.c: In function 'i40e_clean_rx_irq':
drivers/net/ethernet/intel/i40evf/i40e_txrx.c:818:3: error: implicit declaration of function 'prefetch'
make[5]: *** [drivers/net/ethernet/intel/i40evf/i40e_txrx.o] Error 1
due to an implicit assumption that the prototype from linux/prefetch.h
will be present.
Cc: Mitch Williams <mitch.a.williams@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update the driver version to 0.3.28-k.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
New feature: Enable PTP support in the i40e driver.
Change-ID: I6a8e799f582705191f9583afb1b9231a8db96cc8
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the latest firmware the clear_pxe_mode function will use the
AdminQ request, so call this after AdminQ is set up rather than
relying on i40e_pf_reset() to clear the PXE mode.
Change-ID: Ice8cba2e9cbc3c7bde0a0bcf8eaf5009abef040b
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure the "new" qtx_head[q] register is cleared before
enabling the Tx queue.
Change-ID: I0c7a12815e343a5ae68807af172a35d6c6857935
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set the ITR max and min values to match the hardware max value
and the recommended min value. These values are shifted right
one bit because the register counts in 2 usec units, so leave
a comment to explain.
Change-ID: I289c27955cf6c566a6d21b95c3110b88cbb15dad
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the IPV6EXADD bit is set in the Rx descriptor status, there
was an optional extension header with an alternate IP address
detected. The HW checksum offload doesn't handle the alternate
IP address correctly so likely comes up with the wrong answer.
Thus, if the bit is set we ignore the checksum offload value.
Change-ID: I70ff8d38cdcddccf44107691cae13d0c07c284c8
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If you use ip to change the MAC address of a VF while the VF
driver is loaded, closing the VF interface or unloading the VF
driver will cause the VF driver to remove the MAC filter for its
original (now invalid) MAC address. This would cause the PF
driver to kick an error message to the log, and back to the VF
driver.
Since the VF driver has not really done anything naughty, let's
not punish it. Don't check for MAC address overrides on the
delete operation, just make sure it's a valid address. This keeps
us from spamming the log with confusing errors.
Change-ID: I1f051bd4014e50855457d928c9ee8b0766981b2f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a bug where the driver was erroneously exiting the driver unload
path if one part of the unload failed. Instead of the original way
the driver should always continue when disabling and be sure to disable
all queues.
Change-ID: Ib8c81c596bc87c31d8e9ca97ebf871168475279d
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a bug where ethtool set-channels would return failure when configuring
only one Rx queue.
Change-ID: Id833c48c17d71e352b30f3249f6acf9e7aaec57e
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These changes make Doxygen/kdoc work correctly without warnings.
Change-ID: I2941f38860be805ff7548d84dae35754c83f1d62
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
The current driver will warn the user if the NVM version
is out of date, this raises the bar to a newer version.
Change-ID: I5ec21d8efa4e7c3fdacb56f85d310bb2229b1483
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A previous commit removed any need for these macros, so remove
them too.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These instances were found by coccinelle/spatch, and can
use struct assignment instead of memcpy.
Change-ID: Idc23c3599241bf8a658bda18c80417af3fbfee66
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
- substitute FSF address with URL
- deselect current bat-GW when GW-client mode gets deactivated
- send every DHCP packet using bat-unicast messages when GW-client mode is
enabled
- implement the Extended Isolation mechanism (it is an enhancement of the
already existing batman-AP-isolation). This mechanism allows the user to drop
packets exchanged by selected clients by using netfilter marks.
- fix typ0 in header guard
- minor code cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=6EjB
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Included changes:
- substitute FSF address with URL
- deselect current bat-GW when GW-client mode gets deactivated
- send every DHCP packet using bat-unicast messages when GW-client mode is
enabled
- implement the Extended Isolation mechanism (it is an enhancement of the
already existing batman-AP-isolation). This mechanism allows the user to drop
packets exchanged by selected clients by using netfilter marks.
- fix typ0 in header guard
- minor code cleanups
Signed-off-by: David S. Miller <davem@davemloft.net>
Christoph Paasch says:
====================
Make tcp-metrics source-address aware
Currently tcp-metrics only stores per-destination addresses. This brings
problems, when a host has multiple interfaces (e.g., a smartphone having
WiFi/3G):
For example, a host contacting a server over WiFi will store the tcp-metrics
per destination IP. If then the host contacts the same server over 3G, the
same tcp-metrics will be used, although the path-characteristics are completly
different (e.g., the ssthresh is probably not the same).
In case of TFO this is not a problem, as the server will provide us a new cookie
once he saw our SYN+DATA with an incorrect cookie.
It may be (in case of carrier-grade NAT), that we keep the same public IP but
have a different private IP. Thus, we better reuse the old cookie even if our
source-IP has changed. However, this scenario is probably very uncommon, as
carriers try to provide the same src-IP to the clients behind their CGN.
Patches 1 + 2 add the source-IP to the tcp metrics.
Patches 3 to 5 modify the netlink-api to support the source-IP. From now on,
when using the command "ip tcp_metrics delete address ADDRESS" all entries
which match this destination IP will be deleted.
Today's iproute2 will complain when doing "ip tcp_metrics flush PREFIX" if
several entries are present for the same destination-IP but with different
source-IPs:
root@client:~/test# ip tcp_metrics
10.2.1.2 age 3.640sec rtt 16250us rttvar 15000us cwnd 10
10.2.1.2 age 4.030sec rtt 18750us rttvar 15000us cwnd 10
root@client:~/test# ip tcp_metrics flush 10.2.1.2/16
Failed to send flush request
: No such process
Follow-up patches will modify iproute2 to handle this correctly and allow
specifying the source-IP in the get/del commands.
v2: Added the patch that allows to selectively get/del of tcp-metrics based
on src-IP and moved the patch that adds the new netlink attribute before
the other patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to be able to get/del tcp-metrics based on the src IP. This
patch adds the necessary parsing of the netlink attribute and if the
source address is set, it will match on this one too.
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we now can have multiple entries per destination-IP, the "ip
tcp_metrics delete address ADDRESS" command deletes all of them.
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new netlink attribute for the source-IP and appends it
to the netlink reply. Now, iproute2 can have access to the source-IP.
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
We add the source-address to the tcp-metrics, so that different metrics
will be used per source/destination-pair. We use the destination-hash to
store the metric inside the hash-table. That way, deleting and dumping
via "ip tcp_metrics" is easy.
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we will add also the source-address, we rename all accesses to the
tcp-metrics address to use "daddr".
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
Please pull these updates for the 3.14 stream!
For the mac80211 bits, Johannes says:
"Felix adds some helper functions for P2P NoA software tracking, Joe
fixes alignment (but as this apparently never caused issues I didn't
send it to 3.13), Kyeyoon/Jouni add QoS-mapping support (a Hotspot 2.0
feature), Weilong fixed a bunch of checkpatch errors and I get to play
fire-fighter or so and clean up other people's locking issues. I also
added nl80211 vendor-specific events, as we'd discussed at the wireless
summit."
For the iwlwifi bits, Emmanuel says:
"I have here a rework of the interrupt handling to meet RT kernel
requirements - basically we don't take any lock in the primary interrupt
handler. This gave me a good reason to clean things up a bit on the way.
There is also a fix of the QoS mapping along with a few workarounds for
hardware / firmware issues that are hard to hit.
Three fixes suggested by static analyzers, and other various stuff.
Most importantly, I update the Copyright note to include the new year."
For the bluetooth bits, Gustavo says:
"More patches to 3.14. The bulk of changes here is the 6LoWPAN support for
Bluetooth LE Devices. The commits that touches net/ieee802154/ are already
acked by David Miller. Other than that we have some RFCOMM fixes and
improvements plus fixes and clean ups all over the tree."
Beyond that, ath9k, brcmfmac, mwifiex, and wil6210 get their usual
level of attention. The wl1251 driver gets a number of updates,
and there are a handful of other bits here and there.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
This batch contains one single patch with the l2tp match
for xtables, from James Chapman.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent patch to improve guest receive side flow control (ca2f09f2) had a
slight flaw in the wait condition for the vif thread in that any remaining
skbs in the guest receive side netback internal queue would prevent the
thread from sleeping. An unresponsive frontend can lead to a permanently
non-empty internal queue and thus the thread will spin. In this case the
thread should really sleep until the frontend becomes responsive again.
This patch adds an extra flag to the vif which is set if the shared ring
is full and cleared when skbs are drained into the shared ring. Thus,
if the thread runs, finds the shared ring full and can make no progress the
flag remains set. If the flag remains set then the thread will sleep,
regardless of a non-empty queue, until the next event from the frontend.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huqiu reported current sh_sir driver doesn't
call free_irq() in spite of using request_irq().
This patch replaces request_irq() into devm_request_irq()
to solve this issue
Reported-by: Huqiu Liu<huqiuliu@gmail.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huqiu reported current sh_irda driver doesn't
call free_irq() in spite of using request_irq().
This patch replaces request_irq() into devm_request_irq()
to solve this issue
Reported-by: Huqiu Liu<huqiuliu@gmail.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
nf_tables updates for net-next
The following patchset contains the following nf_tables updates,
mostly updates from Patrick McHardy, they are:
* Add the "inet" table and filter chain type for this new netfilter
family: NFPROTO_INET. This special table/chain allows IPv4 and IPv6
rules, this should help to simplify the burden in the administration
of dual stack firewalls. This also includes several patches to prepare
the infrastructure for this new table and a new meta extension to
match the layer 3 and 4 protocol numbers, from Patrick McHardy.
* Load both IPv4 and IPv6 conntrack modules in nft_ct if the rule is used
in NFPROTO_INET, as we don't certainly know which one would be used,
also from Patrick McHardy.
* Do not allow to delete a table that contains sets, otherwise these
sets become orphan, from Patrick McHardy.
* Hold a reference to the corresponding nf_tables family module when
creating a table of that family type, to avoid the module deletion
when in use, from Patrick McHardy.
* Update chain counters before setting the chain policy to ensure that
we don't leave the chain in inconsistent state in case of errors (aka.
restore chain atomicity). This also fixes a possible leak if it fails
to allocate the chain counters if no counters are passed to be restored,
from Patrick McHardy.
* Don't check for overflows in the table counter if we are just renaming
a chain, from Patrick McHardy.
* Replay the netlink request after dropping the nfnl lock to load the
module that supports provides a chain type, from Patrick.
* Fix chain type module references, from Patrick.
* Several cleanups, function renames, constification and code
refactorizations also from Patrick McHardy.
* Add support to set the connmark, this can be used to set it based on
the meta mark (similar feature to -j CONNMARK --restore), from
Kristian Evensen.
* A couple of fixes to the recently added meta/set support and nft_reject,
and fix missing chain type unregistration if we fail to register our
the family table/filter chain type, from myself.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce an xtables add-on for matching L2TP packets. Supports L2TPv2
and L2TPv3 over IPv4 and IPv6. As well as filtering on L2TP tunnel-id
and session-id, the filtering decision can also include the L2TP
packet type (control or data), protocol version (2 or 3) and
encapsulation type (UDP or IP).
The most common use for this will likely be to filter L2TP data
packets of individual L2TP tunnels or sessions. While a u32 match can
be used, the L2TP protocol headers are such that field offsets differ
depending on bits set in the header, making rules for matching generic
L2TP connections cumbersome. This match extension takes care of all
that.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to i40e only.
Anjali provides a fix where interrupts were not being re-enabled on ICR0
even though they were auto masked by hardware. Then provides a fix to
cleanup RSS initialization because it was doing some extra work, so
remove the extra work and any bugs it created when managing number of
queues. Since hardware requires a full packet template to be pointed to
when adding hardware flow filters, add the template and use it for
programming filters.
Jesse provides a fix to replace the use of driver specific defines with
kernel ETH_ALEN defines. Then disables packet split because with the
use of GRO, we do not need the extra bus overhead. Fixes spelling
error in code comment.
Kamil provides a fix for the driver where the hardware expects the MAC
address in a very specific format and the driver was filing the data
incorrectly.
Mitch provides a fix to resolve a panic on reset by adding checks to
VSI->rx_rings. Then shortens alloc_rx_buff_failed and
alloc_rx_page_failed variables since both part of an RX specific
structure so just remove the _rx part of the name. Then fixes
badly formatted lines, long lines and mis-formatted lines.
Shannon provides a fix to call AQ to release any reservation held by this
PF on the NVM resource lock on startup, in order to clear anything that
might have been left over from a previous run. Then removes interrupt on
AQ error since nearly everything we do is synchronous, using the
interrupt-on-error bit is unnecessary and causing unneeded interrupts.
Adds code to handle the ability to send messages among the physical
function interfaces by the admin queue.
Catherine sets the MFP flag earlier in software init and uses that flag
to decide if other hardware work-arounds are required which turns
off flow director in MFP mode.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
