Bring ezusb and whiteheat into line with the coding style
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
USB serial likes to use port->tty back pointers for the real work it does and
to do so without any actual locking. Unfortunately when you consider hangup
events, hangup/parallel reopen or even worse hangup followed by parallel close
events the tty->port and port->tty pointers are not guaranteed to be the same
as port->tty is the active tty while tty->port is the port the tty may or
may not still be attached to.
So rework the entire API to pass the tty struct. For console cases we need
to pass both for now. This shows up multiple drivers that immediately crash
with USB console some of which have been fixed in the process.
Longer term we need a proper tty as console abstraction
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
in the error case the ipaq driver leaves a dangling pointer to already
freed memory that will be freed again.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB debug port only supports 8 byte rx/tx packets. Although spec implies that
"if a packet larger than eight bytes is received from the remote computer, the
device must break the larger packet into eight-byte packets before sending the
data to the Debug Port", the real PLX NET20DC device does not handle it right -
data is corrupted on debug port end if serial interface sends >8 byte urbs.
Patch below fixes the issue by limiting tx urb to 8 byte.
Signed off by: Aleks Gorelov <dared1st@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb serial decrements the pm counter even if an interface has been
disconnected. If it was a logical disconnect the interface may belong
already to another driver. This patch introduces a check for disconnected
interfaces.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: Stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The 28xb, as documented in comments, has the same ID's as the 28x.
Remove the duplicated ID's from the device tables, and expand the
comment to document this.
Signed-off-by: Ben Collins <ben.collins@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
fix the following sparse warning:
drivers/usb/serial/usb-serial.c:927:43: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/usb-serial.c:927:43: expected unsigned int *minor
drivers/usb/serial/usb-serial.c:927:43: got int *<noident>
CHECK drivers/usb/serial/generic.c
Signed-off-by: Andre Haupt <andre@bitwigglers.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
General cleanup on ir-usb module. Introduced
a common header that could be used also on
usb gadget framework.
Lot's of cleanups and now using macros from the header
file.
Signed-off-by: Felipe Balbi <me@felipebalbi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The get/set 2101_config helpers take an unsigned int rather than an
int. It is safe to change these in each case and may even produce
better code as it will be an unsigned divide rather than a signed
divide in places. All other manipulation was setting/masking bits
which will not be affected by the sign change.
Fixes the following sparse warnings:
drivers/usb/serial/cp2101.c:378:44: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:378:44: expected unsigned int *data
drivers/usb/serial/cp2101.c:378:44: got int *<noident>
drivers/usb/serial/cp2101.c:388:40: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:388:40: expected unsigned int *data
drivers/usb/serial/cp2101.c:388:40: got int *<noident>
drivers/usb/serial/cp2101.c:413:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:413:42: expected unsigned int *data
drivers/usb/serial/cp2101.c:413:42: got int *<noident>
drivers/usb/serial/cp2101.c:421:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:421:42: expected unsigned int *data
drivers/usb/serial/cp2101.c:421:42: got int *<noident>
drivers/usb/serial/cp2101.c:444:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:444:42: expected unsigned int *data
drivers/usb/serial/cp2101.c:444:42: got int *<noident>
drivers/usb/serial/cp2101.c:451:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:451:42: expected unsigned int *data
drivers/usb/serial/cp2101.c:451:42: got int *<noident>
drivers/usb/serial/cp2101.c:458:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:458:42: expected unsigned int *data
drivers/usb/serial/cp2101.c:458:42: got int *<noident>
drivers/usb/serial/cp2101.c:471:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:471:42: expected unsigned int *data
drivers/usb/serial/cp2101.c:471:42: got int *<noident>
drivers/usb/serial/cp2101.c:481:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:481:42: expected unsigned int *data
drivers/usb/serial/cp2101.c:481:42: got int *<noident>
drivers/usb/serial/cp2101.c:561:41: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:561:41: expected unsigned int *data
drivers/usb/serial/cp2101.c:561:41: got int *<noident>
drivers/usb/serial/cp2101.c:591:45: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:591:45: expected unsigned int *data
drivers/usb/serial/cp2101.c:591:45: got int *<noident>
drivers/usb/serial/cp2101.c:597:41: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:597:41: expected unsigned int *data
drivers/usb/serial/cp2101.c:597:41: got int *<noident>
drivers/usb/serial/cp2101.c:608:45: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:608:45: expected unsigned int *data
drivers/usb/serial/cp2101.c:608:45: got int *<noident>
drivers/usb/serial/cp2101.c:614:41: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:614:41: expected unsigned int *data
drivers/usb/serial/cp2101.c:614:41: got int *<noident>
drivers/usb/serial/cp2101.c:623:45: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:623:45: expected unsigned int *data
drivers/usb/serial/cp2101.c:623:45: got int *<noident>
drivers/usb/serial/cp2101.c:680:50: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:680:50: expected unsigned int *data
drivers/usb/serial/cp2101.c:680:50: got int *<noident>
drivers/usb/serial/cp2101.c:690:43: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:690:43: expected unsigned int *data
drivers/usb/serial/cp2101.c:690:43: got int *<noident>
drivers/usb/serial/cp2101.c:715:41: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:715:41: expected unsigned int *data
drivers/usb/serial/cp2101.c:715:41: got int *<noident>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sort out the insane naming like "OperationalFirmwareVersion" which seems
designed to cause formatting problems and RSI
Merge various common code together
Clean up the pointlessly complex and spread about MCR handling
This is really just the low hanging fruit.
Needs lots of testing before it goes upstream so testers and reports
appreciated
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bus_id field is going away, use the dev_set_name() function
to set it properly.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bus_id field is going away, use the dev_name() function instead.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Version number provided in first HEX record.
Signed-off-by: Jaswinder Singh <jaswinder@infradead.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The reason for forcing a number of ports should be documented.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thanks to umesh b <umesh.kollam@gmail.com> for the information here.
Cc: umesh b <umesh.kollam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here's a new device ID for the ftdio_sio driver.
The diff is with linus's tree as of this morning.
The device is the RigExpert Tiny USB Soundcard Transceiver Interface for ham
radio.
(I didn't actually test this. A fellow ham couldn't get the device to work, and
I suggested binding the device ID using sysfs - see
"http://jk.ufisa.uninett.no/usb/". However, he had had moved on to other things
by then. I guess adding the device ID to the kernel "on spec" won't hurt.
The relevant part of cat /proc/bus/usb/devices shows:
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0403 ProdID=ed22 Rev= 5.00
S: Manufacturer=FTDI
S: Product=MixW RigExpert Tiny
S: SerialNumber=00000000
C:* #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=83(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
)
From: Jon K Hellan <hellan@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the interface info matching to all Huawei cards, as they all also
contain a Mass Storage Device interface (usually containing Windows
drivers) which should not get bound by this driver.
See also drivers/usb/storage/unusual_devs.h
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've just got a USB GPRS/EDGE modem branded Manufacturer Micromax Model
MMX610U (see http://www.airtel.in/level2_t3data.aspx?path=1/106/179)
working by adding another product ID to pl2303. Modem info reports same
module as Max Arnold's i.e.SIMCOM SIM600 but with product ID 0x0612
(cf Ox0611).
From: Steve Murphy <steve@gnusis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the range of PIDs
that have been allocated for FTDI based devices
at Matrix Orbital.
A small number of units have been shipped early 2008
with a faulty USB Descriptor. Products that may have
this issue have been marked with the existing quirk to
work around the problem.
Signed-off-by: R. Molenkamp <rmolenkamp@matrixorbital.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Recent USB-serial devices using the WinChipHead CH340/CH341 chipset are
being shipped with a new vendor/product ID code pair, but an otherwise
identical device. (This is confirmed by looking at INF for the included
Windows driver.)
Patch is tested and working, both with new and old devices.
Signed-off-by: Michael F. Robbins <mrobbins@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes the name of the onda MSA501HS device, I guess it is called
different things in different countries.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the Telit UC864-E HDSPA modem support to the option driver.
This lets their customers comply with the GPL instead of having to use a
binary driver from the manufacturer.
Cc: Simon Kissel <kissel@viprinet.com>
Cc: Nico Erfurth <ne@nicoerfurth.de>
Cc: Andrea Ghezzo <TS-EMEA@telit.com>
Cc: Dietmar Staps <Dietmar.Staps@telit.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch reverts 57833ea6b9
("usb-serial: pl2303: add support for RATOC REX-USB60F") and adds
support for the device to ftdi_sio driver.
Cc: Akira Tsukamoto <akirat@rd.scei.sony.co.jp>
Cc: stable <stable@kernel.org>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
New variant of the 5520 found by Luke Sheldrick.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This device is not a serial port, but a virtual CD-ROM device. For
example with my Novatel MC950D:
lsusb -v -d 1410:5010 | grep InterfaceClass
bInterfaceClass 8 Mass Storage
After some time (ca. 5min) or if virtual CD is ejected, device id
changes to 1410:4400:
% lsusb -v -d 1410:4400 | grep InterfaceClass
bInterfaceClass 255 Vendor Specific Class
bInterfaceClass 255 Vendor Specific Class
Variable name says that 0x5010 is a Novatel U727, but searching in
internet shows, that this device also provides virtual CD that should be
ejected before use. Product id for serial port in this case is 0x4100.
Signed-off-by: Eugeniy Meshcheryakov <eugen@debian.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the proposed patch allows the ET502HS HDSPA modem to be handled by the
"option" driver. It has been tested for 1 month and works reliably (no
oopses, no hangs, 300KB/s throughput).
Signed-off-by: Mauro Andreolini <andreoli@weblab.ing.unimo.it>
Signed-off-by: Matthias Urlichs <matthias@urlichs.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As reported by Magnus Boman <captain.magnus@opensuse.org>
Cc: Magnus Boman <captain.magnus@opensuse.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This should work on a KRZR K1m, and some other Motorola phones that do
not use the "standard" cdc ACM protocol to talk to USB hosts.
Tested-by: Jeff Garzik <jeff@garzik.org>
Cc: Jiang Dejun <a5652c@motorola.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The file drivers/usb/serial/iuu_phoenix.c uses "int" for flags. This can
cause hard to find bugs on some architectures. This patch converts the flags
to use "long" instead.
This bug was discovered by doing an allyesconfig make on the -rt kernel where
checks are done to ensure all flags are of size sizeof(long).
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following patch fixes a [probable] copy & paste mistake in
airprime.c. Instead of unlocking an acquired mutex, the actual
code tries to lock it again.
Signed-off-by: Leonardo Chiquitto <lchiquitto@novell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The test for an mos7840_set_uart_reg() error return value only works when
status is signed. propagate its error value.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Cc: SL Baur <steve@xemacs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Operations are now a shared const function block as with most other Linux
objects
- Introduce wrappers for some optional functions to get consistent behaviour
- Wrap put_char which used to be patched by the tty layer
- Document which functions are needed/optional
- Make put_char report success/fail
- Cache the driver->ops pointer in the tty as tty->ops
- Remove various surplus lock calls we no longer need
- Remove proc_write method as noted by Alexey Dobriyan
- Introduce some missing sanity checks where certain driver/ldisc
combinations would oops as they didn't check needed methods were present
[akpm@linux-foundation.org: fix fs/compat_ioctl.c build]
[akpm@linux-foundation.org: fix isicom]
[akpm@linux-foundation.org: fix arch/ia64/hp/sim/simserial.c build]
[akpm@linux-foundation.org: fix kgdb]
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* endianness annotations
* endianness fixes
* missing get_unaligned/put_unaligned
It's pretty much all over the place, changes to different files are independent.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Serial-parts-Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- If a termios change fails due to lack of memory we should copy the
old settings back over as the device has not changed
- Note various locking problems
- kl5kusb105 had various remaining tty flag handling problems
- Make safe_serial use tty_insert_flip_string not open coded loops
- set termios speed properly in usb_serial
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove the unused check for num_interrupt and friends as well as remove
them from the header file because no usb-serial drivers no longer
reference them.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usb-serial core no longer checks these fields so remove them from
all of the individual drivers. They will be removed from the usb-serial
core in a patch later in the series.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Setting DTR et al. should work for all interfaces
if you actually pass the interface number. :-P
This should help with devices that have important pseudo-serial ports
that aren't on the first interface in the device.
Signed-off-by: Chris Collins <chris@ursys.com.au>
Signed-off-by: Matthias Urlichs <matthias@urlichs.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Given that most of drivers/usb/serial/Kconfig is wrapped inside:
if USB_SERIAL
...
endif # USB_SERIAL
remove the consequently redundant dependencies on USB_SERIAL.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removes unimplemented TCFLSH handling from oti6858, because it was
preventing TCFLSH handling by upper layer (line discipline) drivers (see
drivers/char/tty_io.c line 3450).
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Original version of the driver done by Linxb, changes by Harald, and
lots of cleanups by me in order to get it into a mergable state.
Cc: Linxb <xubin.lin@worldplus.com.cn>
Cc: Harald Klein <hari@vt100.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is for the sierra driver and adds support for a new group of
devices that have a new USB configuration.
This targets kernel 2.6.25-rc7
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is for the sierra driver and fixes a Compass 597 bug that
allows users to access the SD-Card.
This targets kernel 2.6.25-rc7
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleans up some of the sierra driver code. Please package this
with the other patches in this group as I would like the driver version
to reflect their changes as well.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since nothing under the USB serial/ directory seems to be obviously
experimental, remove the EXPERIMENTAL dependency from all of those
Kconfig entries.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The recent changes to this driver cleaned it up a lot, follow that up
by sorting the speed side of things out as well
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ipaq module supports devices with one endpoint only. Some devices,
e.g. Yakumo Delta 300, have more than one endpoint.
This patch fixes support for devices having up to 2 endpoints which used
to work on older kernel versions.
Signed-off-by: Matthias Geissert <matthias.geissert@web.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Coverity checker (and Adrian Bunk) spotted an inconsistent NULL check of
port->tty (it's blindly dereferenced later without the check).
Alan Cox confirmed the check can go.
Signed-off-by: Ray Lee <ray-lk@madrabbit.org>
Cc: Adrian Bunk <bunk@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The kernel.h macro DIV_ROUND_UP performs the computation (((n) + (d) - 1) /
(d)) but is perhaps more readable.
An extract of the semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@haskernel@
@@
#include <linux/kernel.h>
@depends on haskernel@
expression n,d;
@@
(
- (n + d - 1) / d
+ DIV_ROUND_UP(n,d)
|
- (n + (d - 1)) / d
+ DIV_ROUND_UP(n,d)
)
@depends on haskernel@
expression n,d;
@@
- DIV_ROUND_UP((n),d)
+ DIV_ROUND_UP(n,d)
@depends on haskernel@
expression n,d;
@@
- DIV_ROUND_UP(n,(d))
+ DIV_ROUND_UP(n,d)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ftdi_sio driver has no internal locking on the dtr/rts state. Flag
that up for someone to fix.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Take the lock in usb-serial instead. As it relies on the BKL internally
we can't push it any deeper yet.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The cypress app note for the M8 states that for the USB low speed
version of the part, throughput is effectively limited to 800
bytes/sec. So if we were to try a faster baud rate in such cases then
we risk overrun errors on receive. Best to just identify this case
and limit the rate to 4800 baud or less (by ignoring any request to
set a faster rate). The old baud rate setting code was somewhat
fragile; this change also hopefully makes it easier in the future to
better checking / limiting.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove a NULL check in cypress_m8; the check is useless in this
context because it is referenced earlier in the same code path thus
the kernel would be oops'ed before reaching this point anyway. (And
it's really pointless here anyway; if this pointer somehow is NULL the
driver is going to have serious problems in many other places.)
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Earthmate LT-20 devices (both "old" and "new" versions) can't tolerate
a GET_CONFIG command. The original Earthmate has no trouble with
this. Presumably other non-Earthmate devices are still OK as well.
This change disables the use of GET_CONFIG for cases where it is known
not to work.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
cypress_m8: Packet format is separate from characteristic size
The Cypress app note states that when using an 8 byte packet buffer
size that the packet format is modified (to be more compact). However
I have since discovered that newer DeLorme Earthmate LT-20 devices
(those that are low speed USB with 8 byte packet size) STILL use the
format that is really supposed to correspond to 32 byte packets.
Further confusing things is the subsequent discovery that there are
actually two different types of LT-20 - older LT-20's use 32 byte
packets which is probably why this issue wasn't originally
encountered. The solution here is to flag the packet format
separately from the buffer size. Then at initialization time,
identify the correct combination and set it up. This is a critical
fix for anyone with a newer LT-20. Older devices and non-Earthmate
devices should remain unaffected by this change. (If other devices
behave in this, uh, unexpected manner, it's now just a simple 1 line
change to fix them as well (change the pkt_fmt member for that
device). Default behavior with this patch is still to drive the
format as per the app-note; of course for Earthmate devices this is
overridden.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
cypress_m8: Feature buffer fixes
From: Mike Isely <isely@pobox.com>
Don't hardcode the feature buffer size; use sizeof() instead. That
way we can easily specify the size in a single spot. Speaking of the
feature buffer size, the Cypress app note (and further testing with a
DeLorme Earthmate) suggests that this size should be 5 not 8 bytes.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These strings always come up as false positives whenever I'm doing
git-conflict fixups (ie: about 1000 times/day).
I don't think the zillion "<" and ">" characters are very useful and removing
them makes my life that little bit easier.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
None of these files use any of the functionality promised by
asm/semaphore.h. It's possible that they rely on it dragging in some
unrelated header file, but I can't build all these files, so we'll have
fix any build failures as they come up.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
The num_interrupt_in, num_bulk_in, and other checks in the usb-serial
code are just wrong, there are too many different devices out there with
different numbers of endpoints. We need to just be sticking with the
device ids instead of trying to catch this kind of thing. It broke too
many different devices.
This fixes a large number of usb-serial devices to get them working
properly again.
Cc: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch add new vendor ID and device ID for AMOI HSDPA modem.
From: tang kai <tangk73@hotmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- declare the unusal device for Huawei data card devices in
unusual_devs.h
- disable the product ID matching for Huawei data card devices in
usb_match_device function of driver.c
- declare the product IDs in option.c.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The modem was detected, the ttyUSB{0,1,2} appeared, a call could be
made, and the expected data rate was achieved. Tested for an hour or
two, total of 100Mb. I shall do more testing.
Signed-off-by: James Cameron <quozl@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes the keyspan driver after the addition of additional
checking of driver requirements introduced in usb-serial.c
commit 063a2da8f0. The initialization
of the keyspan usb_serial_driver structs were not initializing the
num_interrupt_out field and the additional checking was rejecting
the end point so the driver wouldn't finish initializing.
This commit initializes the fields to NUM_DONT_CARE.
It works for the keyspan USA-49WG and doesn't break the USA-19HS
which are the two keyspan devices I have to test with.
Signed-off-by: Clark Rawlins <clark.rawlins@escient.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes a bug/inconsistency revealed by the additional sanity checking in
commit 063a2da8f0
introduced in the original 2.6.24 branch.
The Handspring Visor / PalmOS 4 device structure defines .num_bulk_out=2
but the usb-serial probe returns num_bulk_out=3, triggering the check in
the above commit and forcing a bail out when the device (a Garmin iQue in
my case) attempts to connect. The patch bumps the expected number of
endpoints to 3.
FWIW, this patch will probably solve the following kernel bug report for
Treo users (identical symptoms, different model PalmOS units):
<http://bugzilla.kernel.org/show_bug.cgi?id=10118>
Signed-off-by: Brad Sawatzky <brad+kernel@swatter.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the Telegesys ETRX2USB which
works fine with the cp2101 driver.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Tested-by: Xavier Carcelle <xavier.carcelle@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The changes introduced in commit
063a2da8f0 changed the semantics of the
num_interrupt_in, num_interrupt_out, num_bulk_in and num_bulk_out
entries of the usb_serial_driver struct to be the number of endpoints
the device has when probed.
This patch changes the ti_1port_device usb_serial_driver struct to
reflect this change. The single port devices only have 1
bulk_out endpoint in their initial configuration, and so this patch
changes the number of other types to NUM_DONT_CARE.
The same change probably needs doing to the ti_2port_device struct,
but I don't have a two port device at hand.
Signed-off-by: Robert Spanton <rspanton@zepler.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the MC8775 device to the sierra driver.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
while I was adding autosuspend to that driver I noticed a few issues.
You were having DMAed buffers as a part of a structure.
This will fail on platforms that are not DMA-coherent (arm, sparc, ppc, ...)
Please test this patch to fix it.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is a patch that adds support for the propox jtagcable II dongle
(http://www.propox.com/products/t_117.html): their PID was missing,
therefore we were not able to have the device recognized though it uses
a standard FTDI chip.
Signed-off-by: Mirko Bordignon <mirko.bordignon@ieee.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This updates the option driver with a lot more novatel driver ids.
From: Dirk DeSchepper <ddeschepper@nvtl.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for UPS Powercom USB interface (0d9f:0002) in chip CY7C63723.
In my case, this Powercom BNT800AP.
Signed-off-by: Dmitry Shapin <shapin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Nobody should be using the generic usb-serial for anything other than
testing. Still, it's not a good thing that it's easy to lock up. There
is a traceback from NMI oopser here:
https://bugzilla.redhat.com/show_bug.cgi?id=431379
But in short, if a line discipline has a chance to echo anything, input
can loop back a write method. So, don't call tty_flip_buffer_push from
under a lock taken on write path.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Workaround for the FT232RL-based, Matrix Orbital VK204-25-USB serial port
added to the ftdi_sio driver.
The device has an invalid endpoint descriptor, which must be modified
before it can be used.
Signed-off-by: Kevin Vance <kvance@kvance.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the mos7820/7840-based B&B USOPTL4_2/USOPTL4_4 USB/RS485
converter to mos7840.c
Signed-off-by: Dave Ludlow <dave.ludlow@bay.ws>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the Onda H600/ZTE MF33 device from the sierra driver to the option
driver.
The reason it was moved is because the sierra driver is starting to support
more and more sierra proprietary features, so it makes more sense to keep
sierra only devices in there.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this is a small patch to add support for a rebranded Novatel modem (see
http://ubuntuforums.org/archive/index.php/t-608388.html for details).
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The option driver
- violates DMA coherency rules
- allocates ~16500 bytes in one chunk
This patch splits out the buffers and uses __get_free_page() to avoid
higher order allocations.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-By: Matthias Urlichs <matthias@urlichs.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The device setup did miss to initialize the num_interrupt_out field, thus
failing to successfully complete the probe function.
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Cc: stable <stable@kernel.org>
Cc: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 04d06ad0f1 have added menuconfig support
for the whole USB Kconfig, but there are still menuconfig need for usb/serial,
usb/atm, and usb/gadget, so that the user can disable all the options in that
menu at once instead of having to disable each option separately.
Signed-off-by: Denis Cheng <crquan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
these drivers abused intfdata in close() as flags for binding.
That races with reprobing of those devices. This patch fixes that by using
the flag and the locks introduced with the patch against mos7720.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If disconnect() is called for a logical disconnect, no more IO must be
done after disconnect() returns, or the old and new drivers may conflict.
This patch avoids this by using the flag and lock introduced by the earlier
patch for the mos7720 driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Rename the copied buffer functions from pl2303 to oti6858 to avodi
confusion
- Initialise speeds properly
- Use modern baud rate handling
- Remove GSERIAL/SSERIAL ioctl hacks that reference termios unlocked
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this covers the rest of the obvious cases by using the flags
and locks to guard against disconnect which were introduced
in the earlier patch against mos7720.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If disconnect() is called for a logical disconnect, no more IO must be
done after disconnect() returns, or the old and new drivers may conflict.
This patch avoids this by using the flag and lock introduced by the earlier
patch for the mos7720 driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
in an error case memory already allocated must be freed again.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this driver uses usb_get_intfdata() == NULL as a test for disconnect().
You must not do that as this races with probe(). By the time you test
your erstwhile interface may already be somebody else's interface.
This fixes the close() method of cypress_m8 to use the recently introduced
flag and use locking against disconnect() where required in close().
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a problem where the mos7720 driver will make io to a device from
which it has been logically disconnected. It does so by introducing a flag by
which the generic usb serial code can signal the subdrivers their
disconnection and appropriate locking.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
People keep trying to add entries to this section of the driver for
things. That's what the Changelog is supposed to be for, not the .c
file.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When building an external module, the ezusb_* functions are not defined
if we haven't loaded any built'in module that use them (whiteheat,
keyspan, ...).
This patch allow to build those functions even if we only have selected
the usbserial generic driver.
Signed-off-by: Paul Chavent <paul.chavent@fnac.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following improvements were made:
- Fixed control line issue where asserting DTR on ep5 would close ep2
- Added support for calc_num_ports (will help support future composite
devices)
Signed-off-by: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[PATCH] ftdi_sio: add support for more FTDI based JTAG adaptors
There are more devices similar to the Olimex JTAG adaptor, in that the first
port of the FT2232C is used for JTAG, and only the second port is available as
UART.
I have thus renamed ftdi_olimex_{probe,quirk} to ftdi_jtag_{probe,quirk} and
added vendor/product ID's for the OpenMoko Neo1973 Debug Board as well as the
OOCDlink device.
I've also updated the KERN_INFO message sent to userspace to remove the word
'olimex' and an extra '\n' that was causing an empty line in dmesg.
Signed-off-by: Harald Welte <laforge@openmoko.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Don't pass NULL into termios functions when calling them internally
Remove all the crap which then checks for NULL which can't occur now
Clear CMSPAR as it is not supported
Report the baud rate back to the caller properly (See FIXME someone with
the docs)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove internal NULL passing in termios code
Remove all the if checks it causes
Encode the baud rate back properly
Clear CMSPAR as it is not supported
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove lots of NULL checks that can no longer occur
Encode the baud rate back into the termios (again someone with docs see
FIXME to improve this further)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Am Sonntag, 16. Dezember 2007 05:23:47 schrieb Andrew Morton:
> On Sat, 15 Dec 2007 07:08:52 -0800 (PST) bugme-daemon@bugzilla.kernel.org wrote:
>
> > http://bugzilla.kernel.org/show_bug.cgi?id=9573
> > There's a null pointer dereference on drivers/usb/serial/whiteheat.c as
> > follows:
> >
> > (1) line 613: the test "if (port->tty)" implies that null is a legal value
> > for "port->tty" at that point
> >
> > (2) neither firm_open nor firm_purge initialize "port->tty"
drivers/usb/serial/usb-serial::serial_open() sets port->tty
The check for NULL is bogus. This patch removes the check.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A tester with actual hardware would be useful
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Without this fix, the pl2303 usb-serial adapter would not suspend properly
unless it had been opened first. A pl2303 type_1 chip will still break if the
system is hibernated while the RS-232 connector is powered by another system.
This was broken before, and a reset resume does not fix it. All other suspend
and autosuspend scenarios work with ATEN pl2303 adaptors with HX and type_1 chips.
Signed-off-by: Sarah Sharp <saharabeara@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace the FISH and SOUP macros that violated the macro guidelines in CodingStyle.
Turn them into function calls with clearer variable names.
Signed-off-by: Sarah Sharp <saharabeara@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Edgeport USB Serial Converter: convert semaphore es_sem to the
mutex API
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This also fixes a sparse warning that symbol 'result' shadows an earlier one.
Signed-off-by: Andre Haupt <andre@bitwigglers.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Claim the interface for a USB to serial converter when the tty is open,
and release the interface when the tty is closed.
If a driver doesn't provide a resume function, use the generic resume
instead.
Make sure the generic resume function does not submit the URBs if we're
coming back from autosuspend. On autoresume, we know that the open
function will be called next, which will attempt to submit the URBs. If
we submit them in the resume function, the open will fail.
This works for:
- autosuspend
- suspending with the tty open or closed
- hibernate with the tty closed
A hibernate (or a suspend that causes the USB subsystem to lose power)
has issues. If you have the tty open when you hibernate, a new tty will
be created when the device re-enumerates during resume.
Signed-off-by: Sarah Sharp <sarah.a.sharp@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usb serial method set_termios() is called for the first time from
open() method in order to set up the termios structure with the default
device's settings, ignoring the current settings. Once it's initialized,
the next set_termios() calls will update the device with the
tty->termios settings.
Currently USB serial console code calls the driver open() method without
a tty and after that will allocate a fake tty and termios so the command
line arguments can be applied to the device
(console=ttyUSB0,115200,...). This makes the driver overwrite the
termios with the default settings and not applying the command line
options.
This patch changes usb_console_setup() to allocate the fake tty and
termios before the open() method is called.
Tested successfully with a pl2303
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a usb serial adapter is used as console, the usb serial console
driver bumps the open_count on the port struct used but doesn't attach
a real tty to it (only a fake one temporaly). If this port is opened later
using the regular character device interface, the open method won't
initialize the port, which is the expected, and will receive a brand new
tty struct created by tty layer, which will be stored in port->tty.
When the last close is issued, open_count won't be 0 because of the
console usage and the port->tty will still contain the old tty value. This
is the last ttyUSB<n> close so the allocated tty will be freed by the
tty layer. The usb_serial and usb_serial_port are still in use by the
console, so port_free() won't be called (serial_close() ->
usb_serial_put() -> destroy_serial() -> port_free()), so the scheduled
work (port->work, usb_serial_port_work()) will still run. And
usb_serial_port_work() does:
(...)
tty = port->tty;
if (!tty)
return;
tty_wakeup(tty);
which causes (manually copied):
Faulting instruction address: 0x6b6b6b68
Oops: Kernel access of bad area, sig: 11 [#1]
PREEMPT PowerMac
Modules linked in: binfmt_misc ipv6 nfs lockd nfs_acl sunrpc dm_snapshot dm_mirror dm_mod hfsplus uinput ams input_polldev genrtc cpufreq_powersave i2c_powermac therm_adt746x snd_aoa_codec_tas snd_aoa_fabric_layout snd_aoa joydev snd_aoa_i2sbus snd_pcm_oss snd_mixer_oss snd_pcm snd_timer snd_page_alloc pmac_zilog serial_core evdev ide_cd cdrom snd appletouch soundcore snd_aoa_soundbus bcm43xx firmware_class usbhid ieee80211softmac ff_memless firewire_ohci firewire_core ieee80211 ieee80211_crypt crc_itu_t sungem sungem_phy uninorth_agp agpart ssb
NIP: 6b6b6b68 LR: c01b2108 CTR: 6b6b6b6b
REGS: c106de80 TRAP: 0400 Not tainted (2.6.24-rc2)
MSR: 40009032 <EE,ME,IR,DR> CR: 82004024 XER: 00000000
TASK = c106b4c0[5] 'events/0' THREAD: c106c000
GPR00: 6b6b6b6b c106df30 c106b4c0 c2d613a0 00009032 00000001 00001a00 00000001
GPR08: 00000008 00000000 00000000 c106c000 42004028 00000000 016ffbe0 0171a724
GPR16: 016ffcf4 00240e24 00240e70 016fee68 016ff9a4 c03046c4 c0327f50 c03046fc
GPR24: c106b6b9 c106b4c0 c101d610 c106c000 c02160fc c1eac1dc c2d613ac c2d613a0
NIP [6b6b6b68] 0x6b6b6b68
LR [c01b2108] tty_wakeup+0x6c/0x9c
Call Trace:
[c106df30] [c01b20e8] tty_wakeup+0x4c/0x9c (unreliable)
[c106df40] [c0216138] usb_serial_port_work+0x3c/0x78
[c106df50] [c00432e8] run_workqueue+0xc4/0x15c
[c106df90] [c0043798] worker_thread+0xa0/0x124
[c106dfd0] [c0048224] kthread+0x48/0x84
[c106dff0] [c00129bc] kernel_thread+0x44/0x60
Instruction dump:
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
Slab corruption: size-2048 start=c2d613a0, len=2048
Redzone: 0x9f911029d74e35b/0x9f911029d74e35b.
Last user: [<c01b16d8>](release_one_tty+0xbc/0xf4)
050: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b
Prev obj: start=c2d60b88, len=2048
Redzone: 0x9f911029d74e35b/0x9f911029d74e35b.
Last user: [<c00f30ec>](show_stat+0x410/0x428)
000: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b
010: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b
This patch avoids this, clearing port->tty considering if the port is
used as serial console or not
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently usb serial console support ignores the device and always use
ttyUSB0.
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
TI 3410/5052 USB Serial: convert semaphore td_open_close_lock to the mutex
API.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've got a Dell wireless 5520 card with a different USB ID - specifically, 8136
instead of 8137. Attached a small patch to add support, and the output of an
'ati3'.
If we could get this in, that'd be sweet. ;) Thanks!
nc@knight:~/tmp/linux-2.6.24-rc8/drivers/usb/serial$ lsusb | grep 8136
Bus 001 Device 005: ID 413c:8136 Dell Computer Corp.
nc@knight:~/tmp/linux-source-2.6.23/drivers/usb/serial$ cu -l ttyUSB0 -s 115200
Connected.
ati3
Manufacturer: Novatel Wireless Incorporated
Model: Expedite EU860D MiniCard
Revision: 10.10.04.01-01 [2007-04-11 14:07:19]
IMEI: 011186000228043
+GCAP: +CGSM,+DS,+ES
From: Nate Carlson <natecars@natecarlson.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added support for the Elster Unicom III Optical Probe.
The device ID has already been added to the usb.ids file.
Cc: stable <stable@kernel.org>
Signed-off-by: Ed Beroset <beroset@mindspring.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pl2303: add support for RATOC REX-USB60F
This patch adds support for RATOC REX-USB60F Serial Adapters,
which is widely used in Japan recently.
Cc: stable <stable@kernel.org>
Signed-off-by: Akira Tsukamoto <akirat@rd.scei.sony.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added support for Onda H600/Zte MF330 GPRS/UMTS/HSDPA datacard
Cc: stable <stable@kernel.org>
Signed-off-by: Bruno Redondi <bruno.redondi@altarisoluzione.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
little patches only to add vendor/device id of ATK_16IC CCD cam for
astronomy.
From: Franco Lanza <nextime@nexlab.it>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I work with a group of people on a free home automation tool called
FHEM. Some of the users own more than one USB-serial device by ELV. The
ftdi_sio driver has most of the ELV devices disabled by default and
needs to be re-enabled every time you get a new kernel. Additionally a
new device (EM 1010 PC - enegry monitor) is missing in the list.
Currently our users have to follow the instructions we provide at
http://www.koeniglich.de/fhem/linux.html ... However, to some users it
is too complicated to compile their own kernel module.
We are aware that you can specify one additional device using the
vendor/product option of the module. But lot's of users own more than
one device.
Cc: stable <stable@kernel.org>
Signed-off-by: Peter Stark <peter.stark@t-online.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following improvements were made:
- Added new product support: MC5725, AC 880 U, MP 3G (UMTS & CDMA)
Cc: stable <stable@kernel.org>
Signed-off-by: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This simply adds the "YC Cable" as a vendor and its pl2303-based
USB<->Serial adapter as a product. This particular adapter is sold by
Radio Shack. I've done limited testing on a few different systems with
no issues.
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds the appropriate vendor and device IDs for the AirCard 881U to
sierra.c. (This device is often rebadged by AT&T as the USBConnect 881).
Cc: stable <stable@kernel.org>
Signed-off-by: Jessica L Blank <j@twu.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we get a data URB back from the hardware after we have put the tty to
bed we go kaboom. Fortunately all we need to do is process the URB
without trying to ram its contents down the throat of an ex-tty.
Cc: stable <stable@kernel.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we get a data URB back from the hardware after we have put the tty to
bed we go kaboom. Fortunately all we need to do is process the URB without
trying to ram its contents down the throat of an ex-tty.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@akpm@linux-foundation.org>
Cleaning out all the incorrect 'no change made' checks for termios
settings showed up a problem with the PL2303. The hardware here seems to
lose sync and bits if you tell it to make no changes. This shows up with
a real world application.
To fix this the driver check for meaningful hardware changes is restored
but doing the tests correctly and as a tty layer function so it doesn't
get duplicated wrongly everywhere if other drivers turn out to need it.
Signed-off-by: Alan Cox <alan@redhat.com>
Tested-by: Mirko Parthey <mirko.parthey@informatik.tu-chemnitz.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
attached please find a new device ID for CP2101 driver. This device is a
usb stick from Dynastream to communicate with ANT wireless devices which
I suppose is fairly similar to the ANT dev board having product id 0x1003.
From: Martin Kusserow <kusserow@ife.ee.ethz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds VID/PID for the MC8775 found internally in the Thinkpad X61s laptop
(and likely others). For commercial reasons the driver maintainer cannot
add VID/PIDs for laptop OEM devices himself.
Signed-off-by: Kevin R Page <linux-kernel@krp.org.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a bunch of problems we are having with the Huawei devices...
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jaime Velasco Juan <jsagarribay@gmail.com>
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds a device ID for the Aerocomm Radio Modem, which uses the
cp2102. I'm sure changing num_bulk_in/num_bulk_out to NUM_DONT_CARE
is the wrong fix, but this is the only device I have with a cp2102,
so I have no idea what a good global value would be, if there is one.
Zero didn't work with this device.
From: Jeff Long <JeffLong@mitre.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Attached is a patch to fix the addition of the new product ids I sent.
It is against 2.6.24-rc4, as Linus included the broken version of the
patch I sent you in that tree. :(
Not sure if this is the right method to go about this, but hopefully I got
it right this time.
Signed-off-by: Andrew Gilmore <agilmore@wirelessbeehive.com>
CC: Kevin Lloyd <klloyd@sierrawireless.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Revert 7eea436433.
Lucy said:
This patch will work with the 19HS but WILL BREAK all other Keyspan
adapters. It will take me a few days to get to looking at a correct fix but
that keyspan_send_setup(port, 1) (and the '1' is the important part) must
happen once when the port is first opened. The cflag can just be set to
whatever the normal default is for your serial environment.
So revert this again pending the proper fix.
Cc: Borislav Petkov <bbpetkov@yahoo.de>
Cc: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Lucy McCoy <lucy@keyspan.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Per the maintainer of the usbserial/sierra.c driver, the patch below adds
a new id to the list of supported cards for the sierra driver. Tested and
working for me on Fedora 8, kernel 2.6.23 and on the more recent sierra.c
available in
http://www.sierrawireless.com/resources/support/Software/Linux/v.1.2.6b(kernel2.6.21).zip
Hardware is a MiniPCI card in a Lenovo T61p.
Signed-off-by: Andrew Gilmore <agilmore@wirelessbeehive.com>
Cc: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In commit acd2a847e7 usb_serial_generic_write()
disables interrupts when taking &port->lock which is also taken in
usb_serial_generic_read_bulk_callback() resulting in an inconsistent lock state
due to the latter not disabling interrupts on the local cpu. Fix that by
disabling interrupts in the latter call site also.
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pl2303: add support for Corega CG-USBRS232R
This patch adds support for Corega CG-USBRS232R Serial Adapters.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove redundant code leading to NULL ptr deref and let terminal config
settings take place in the proper initialization path in
usb_console_setup().
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Cc: <lucy@keyspan.com>
Cc: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
USB: usbserial - fix potential deadlock between write() and IRQ
usb_serial_generic_write() doesn't disable interrupts when taking port->lock,
and could therefore deadlock with usb_serial_generic_read_bulk_callback()
being called from interrupt, taking the same lock. Fix it.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the IO Data Device USB-RSAQ5, PL2303 based
USB-serial converter, to pl2303 driver
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
WARNING: line over 80 characters
#23: FILE: drivers/usb/serial/ftdi_sio.c:297:
+ speed_t force_baud; /* if non-zero, force the baud rate to this value */
ERROR: use tabs not spaces
#31: FILE: drivers/usb/serial/ftdi_sio.c:881:
+^I$
ERROR: use tabs not spaces
#39: FILE: drivers/usb/serial/ftdi_sio.c:890:
+^I$
WARNING: line over 80 characters
#111: FILE: drivers/usb/serial/ftdi_sio.c:1956:
+ tty_encode_baud_rate(port->tty, priv->force_baud, priv->force_baud);
Your patch has style problems, please review. If any of these errors
are false positives report them to the maintainer, see
CHECKPATCH in MAINTAINERS.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No hardware termios setting in this case so keep the old settings
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For the devices that have no hardware settings set up the termios return
properly.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Clear unsupported CMSPAR bit
- Clean up long chains of a->b-> a bit
- Encode baud rate back into tty structure properly
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Clean up paranoia checks
- Propogate back a correct fixed termios
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The empeg is pretty fixed. Tidy up the long foo->bar->baz stuff and
encode the fixed speed properly.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Expand some x&y to x & y so I could read it when checking
- Clear CMSPAR bit in the termios (as the driver does not support it)
- Encode the speed using the new tty_encode_baud_rate facility
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ch341 currently doesn't support most of the hardware setting. So to keep
the termios data right we propogate the old termios hardware values back then
encode the speed.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Set the i/ospeed in the initial termios properly
- Use the tty_encode_baud_rate functions to report resulting rates properly
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Most of these fixes were already submitted for old kernel versions, and were
approved, but for some reason they never made it into the releases.
Because this is a consolidation of a couple old missed patches, it touches both
Kconfigs and documentation texts.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
* Convert files to UTF-8.
* Also correct some people's names
(one example is Eißfeldt, which was found in a source file.
Given that the author used an ß at all in a source file
indicates that the real name has in fact a 'ß' and not an 'ss',
which is commonly used as a substitute for 'ß' when limited to
7bit.)
* Correct town names (Goettingen -> Göttingen)
* Update Eberhard Mönkeberg's address (http://lkml.org/lkml/2007/1/8/313)
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Found these while looking at printk uses.
Add missing newlines to dev_<level> uses
Add missing KERN_<level> prefixes to multiline dev_<level>s
Fixed a wierd->weird spelling typo
Added a newline to a printk
Signed-off-by: Joe Perches <joe@perches.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: James Smart <James.Smart@Emulex.Com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as997) fixes a bug in the USB serial core. The core needs
to pay attention to drivers' requirements regarding the number and
type of endpoints a device has.
At the same time, the patch changes the NUM_DONT_CARE constant (which
is stored in a single-byte field) from -1 to a safer, unsigned value.
It also improves the kerneldoc for several fields in the
usb_serial_driver structure.
Finally, the patch replaces a list_for_each() with list_for_each_entry().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Funsoft has a bogus ioctl handler doing bogus termios handling in a bogus
manner. Fortunately we can simply delete all the bogus bits and get the
right default behaviour !
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Visor has a huge complex routine which displays termios bits for debug
but doesn't do anything. Get the correct behaviour by removing it all
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes four needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements a USB serial port driver for the Winchiphead
CH341 USB-RS232 Converter. This chip also implements an IEEE 1284
parallel port, I2C and SPI, but that is not supported by the driver.
Signed-off-by: Frank A Kingswood <frank@kingswood-consulting.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds an additional device ID to the cp2101 USB serial
driver. This device is a Gemalto Prox-PU or CU contactless card reader
(ISO14443-A/B and Mifare). The reader is a standard Gemalto serial
proximity reader using the Gemalto Block Protocol (see reader's
documentation) bundled with a built-in CP2102 for serial/USB
conversion.
Signed-off-by: Edouard Lafargue (edouard@lafargue.name)
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the error code paths can be enter with buffers to freed buffers.
Serial core would do a kfree() on memory already freed.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the iuu_phoenix driver submits another URB from a completion handler.
This dictates a certain order of calls to usb_kill_urb() in kill_traffic().
As other drivers may do it the other way round, we need to use both
orders in kill_traffic().
This patch does so and should be merged before iuu_phoenix is merged.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the BenQ Mobile Phone EF81 to pl2303
Signed-off-by: Andreas Loibl <andreas@andreas-loibl.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In drivers/usb/serial/oti6858.c::pl2303_buf_alloc() the return value
of kmalloc() is being cast to "struct pl2303_buf *", but that need
not be done here since kmalloc() returns "void *".
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some usb-serial devices (e.g. certain Edgeport models) have more than
one serial port on the same USB device/interface.
Currently the only way to distinguish these ports in userspace is by
their minor device number: the driver makes them consecutive and in
stable order.
However, for the purpose of stable naming with udev this is
insufficient: when udev handles the ADD event for one of the ports it
doesn't know what minor number the other one has.
To make stable naming easier, export the port number via sysfs.
Signed-off-by: Roman Kagan <rkagan@sw.ru>
Signed-off-by: Dmitry Guryanov <dimak@dgap.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No hardware but this driver is currently totally broken so we can't make
it much worse. Remove all tbe broken invalid termios handling and replace
it with a proper set_termios method.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Handle the FT232RL device type in exactly the same way as FT232BM
devices (FT232RL detection was added around kernel 2.6.20 but not code
for handling it).
Signed-off-by: Andrew M. Bishop <amb@gedanken.demon.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Coverity checker spotted that we'd have already oops'ed if one of
these was NULL.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make Pete happy
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove the references to CONFIG_USBD_SAFE_SERIAL_{VENDOR,PRODUCT},
which aren't defined in any Kconfig file.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/serial/bus.c: In function usb_serial_bus_deregister:
drivers/usb/serial/bus.c:185:
warning: passing argument 1 of free_dynids from incompatible pointer type
Above build warning comes when CONFIG_HOTPLUG=n because argument of
free_dynids() in serial/bus.c is a struct usb_serial_driver, not a
struct usb_driver. This is not a runtime bug, because the function
is an empty stub and never dereferences the passed pointer anyway.
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is based on information sent in by Christian Gothe.
Cc: Christian Gothe <christian.gothe@kapelan.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I have added to a new product based on the FTDI 232R USB/Serial
transceiver, which is commercialized by The Mobility Lab. Here is a
trivial patch enclosed, against 2.6.22.6 kernel.
Signed-off-by: Pierre Castella <pp.castella@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This stuff is simply not needed.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch enables support for HTC Smartphones. The original patch is at
https://bugs.gentoo.org/show_bug.cgi?id=187522. Original author is Mike Doty
<kingtaco@gentoo.org>.
Signed-off-by: Christian Heim <phreak@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The oti6858 usb serial driver should use kernel_termios_to_user_termios/
user_termios_to_kernel_termios to avoid segfaults because the kernel
uses a structure differing from that of user space with a different
size.
Signed-off-by: Thomas Viehmann <tv@beamnet.de>
CC: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The attached (mostly trivial) patches adds support for the Evolution
Scorpion Robots.
Evolution Robotics supplies a patch against 2.6.8 with their
software. My patch is based on their work, so I don't know if I can
sign it off, or if you need some Evolution people to do this (which
might be hard).
The patch adds device ID's for some robots which is trivial.
From: Søren Hauberg <hauberg@gmail.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Søren
Dell Wireless Broadband ExpressCards are rebrands of Novatel's cards.
Add all of their known PCI IDs to date along with their mapping to the exact
Novatel model to the Option driver which already claims to support them.
Signed-off-by: Faidon Liambotis <paravoid@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix typo in safe_serial.c to match the actual CONFIG variable.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch contains two fixes submitted by Ondrej Palkovsky:
- the 'ACK' packet is sent after the transfer of the USB packet is
completed, i.e. in the write_callback function. Because the close
function sends the 'abort' command, a parameter is added that allows
the caller of garmin_write_bulk to specify, if the 'ack' should be
propagated to the serial link or dimissed.
This fixes the problem with gpsbabel, it has sent several packets that
were acknowledged before they were sent to the GPS and GpsBabel closed
the device - thus effectively cancelled all outstanding requests in the
queue.
- removed the APP_RESP_SEEN and APP_REQ_SEEN flags and changed
them into counters. It evades USB reset of the gps on every device close.
Signed-off-by: Hermann Kneissel <hermann.kneissel@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix serious regression on non-EPiC edgeport usb-serial devices. Baud
rate and MCR/LCR registers are not being written on these models due
to apparent copy-n-paste errors introduced with EPiC support.
Failure reported by Nick Pasich <Nick@NickAndBarb.net>.
Signed-off-by: Adam Kropelin <akropel1@rochester.rr.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes three needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clearly there's a bug in
drivers/usb/serial/usb-serial.c:usb_serial_put(). It shouldn't call
kref_put() while holding a spinlock.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- The outbreak of acute bracketitus has been cured
- The belief that brackets should have spaces everywhere likewise
- Various other coding style tweaks
- Use baud rates not Bfoo in the speed setup switch
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've also enabled the commented out support for 7200, 14400, 55854,
127117 and 3686400 baud as you can now set such rates in the kernel.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Am Montag 23 Juli 2007 schrieb Adrian Bunk:
> Commit ec22559e0b added the following
> function to drivers/usb/serial/usb-serial.c:
>
[..]
>
> The Coverity checker spotted the inconsequent NULL checking for "serial".
>
> Looking at the code it also doesn't seem to have been intended to always
> return 0.
Coverity is right. The check for NULL is wrongly done and the error
return is lost.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Coverity scan found (CID: 1708) this in
drivers/usb/serial/io_ti.c::edge_shutdown() :
...
2797 for (i=0; i < serial->num_ports; ++i) {
2798 edge_port = usb_get_serial_port_data(serial->port[i]);
2799 edge_remove_sysfs_attrs(edge_port->port);
2800 if (edge_port) {
2801 edge_buf_free(edge_port->ep_out_buf);
2802 kfree(edge_port);
2803 }
2804 usb_set_serial_port_data(serial->port[i], NULL);
2805 }
...
It's complaining that we dereference 'edge_port' in line 2799 which
makes the test of that pointer against NULL in 2800 pointless, since if
edge_port was actually NULL we'd have crashed already before reaching
line 2800.
Reading the edge_open() function it seems to me that the pointer
returned by usb_get_serial_port_data(serial->port[i]) and stored in
'edge_port' can never actually be NULL here, so the test is entirely
superfluous (even if it could be NULL it would be pointless here,
ignoring the then possible crash in that case, since both
edge_buf_free() and kfree() can handle being passed NULL pointers.
This patch removes the pointless conditional (and also makes a few
tiny style corrections now that I was in the area anyway).
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Coverity (1709, 1710, 1711, 1712, 1713) actually flagged these as
REVERSE_INULLs (NULL check performed after dereference). But looking at
the other drivers I can't see any similar tests and the USB core already
makes sure urb is non-null - so might as well get rid of the checks.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds new devices to the Sierra Wireless driver. This is being
resubmitted because the dependent patch (patch 01/02) needed to be
resubmitted.
Signed-off-by: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds compatibility with Sierra Wireless' new TRU-Install
feature. Future devices that use this feature will not work unless this
patch has been applied.
Signed-off-by: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The MOS driver is "interesting", in a bad kind of 'how the hell did this
get merged' kind of way
- Remove the bogus termios change check
- Remove the duplicate code for half the ioctls
- Remove the supporting code to duplicate the ioctl code
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix an oops that happens in relation with applying work arounds for buggy
ftdi_sio devices. The quirks were handled too early because due to changes in
the initialisation of usb serial devices the device was not fully initialised
when the old hook was called.
Addresses bug 8564
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Drivers don't call ldisc termios methods. They certainly don't call
them the way this one does - remove wrong call
- The tty buffer code isn't designed to be abused from IRQ handlers and
the new buffering removes the need for the uglies involved - fix them
- Style
- Remove incorrect baud and change handling for termios changes
The driver now has some style, but not a lot - it goes insane if you have
two dongles for example as it continues to use global variables for per
dongle state. That bit isn't my problem.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the baud rate stuff from the kernel don't parse CBAUD directly
Remove pointless and wrong 'no change' check
Could do with some good testing as well but again better than adding &&
BROKEN
(The use of BELKIN_SA_BAUD() might seem a bit odd but x/a = b and x/b =
a (rounded for integers)).
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
o Don't parse the cflag for baud rates, its not valid to do so
any more and this driver got it wrong anyway
o Don't do clever termios change checks in drivers and get them
wrong (arguably we should do some smart ones in the tty core but
stty to change nothing is *not* a common or critical path
I don't have the hardware so if you can test this carefully please do. I
thought fixing it up this far was better than marking it and other bits of
USB serial && BROKEN
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This removes the ugly code that was copied from the keyspan driver and
allocates the in urbs in a much shorter code path that can be understood
easier.
Also turned off the interrupt urb when no port was open as it's not nice
to keep the bus busy for no good reason at all (this should be a power
savings.)
All in all, this saved over 40 lines of code and cleaned things up
better.
Cc: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
You can't rely on the fact that the status really is correct like it was.
Also simplified the write path and now we allocate the urb and data on
the fly, instead of trying to do that really odd timeout check which I
am guessing doesn't really work properly. This should speed up the
device by keeping the hardware queue full easier.
As a benefit, this reduces the size of the driver.
Cc: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
