The vfree() function performs also input parameter validation.
Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
FM (frequency modulated) signal for SDR is generated by varying the
phase, where phase variation is proportional to input signal. It is
seen that, the larger phase increments leads to discontinuities in
the signal recovered after demodulation. Reducing the extent of phase
variation with respect to input signal, equivalent to reducing the
modulation index.
Tested using FM receiver flow graph in gnuradio-companion.
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The common implementation for sin/cos in include/linux/fixp-arith.h
has been improved recently to provide higher precision.
Replacing native implementation of sin/cos in vivid sdr with common
implementation. This serves two purposes:
1. Improved accuracy: the native implementation based on the Taylor
series is more prone to rounding errors.
2. Reuse of common function: this is better compared to maintaining
native versions for each driver.
Suggested by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The cos table used at fixp-arith.h has only 8 bits of precision.
That causes problems if it is reused on other drivers.
As some media drivers require a higher precision sin/cos
implementation, replace the current implementation by one that
will provide 32 bits precision.
The values generated by the new implementation matches the
32 bit precision of glibc's sin for an angle measured in
integer degrees.
It also provides support for fractional angles via linear
interpolation. On experimental calculus, when used a table
with a 0.001 degree angle, the maximum error for sin is
0.000038, which is likely good enough for practical purposes.
There are some logic there that seems to be specific to the
usage inside ff-memless.c. Move those logic to there, as they're
not needed elsewhere.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In case allocation vb2_dma_sg_init_ctx() fails during cx8802_probe(), the
already allocated cx8802 device structure memory is not freed in the used
exit path. Thus adapt the cleanup handling accordingly. Detected by Coverity
CID 1260065.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Memory allocated for sh_vou_file is not deallocated
on error paths in sh_vou_open().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch uses managed resource APIs to allocate memory
in order to simplify the driver unload or failure cases
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If NO_DMA=y:
warning: (VIDEO_OMAP2_VOUT && VIDEO_VIU && VIDEO_TIMBERDALE) selects VIDEOBUF_DMA_CONTIG which has unmet direct dependencies (MEDIA_SUPPORT && HAS_DMA)
drivers/built-in.o: In function `__videobuf_dc_free':
videobuf-dma-contig.c:(.text+0x6f4d32): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `__videobuf_dc_alloc':
videobuf-dma-contig.c:(.text+0x6f4fe6): undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `__videobuf_mmap_mapper':
videobuf-dma-contig.c:(.text+0x6f518e): undefined reference to `dma_free_coherent'
Commit 244829226f ("[media] timberdale: do not select TIMB_DMA")
dropped the dependency of VIDEO_TIMBERDALE on DMADEVICES, and thus the
implicit dependency on HAS_DMA. VIDEO_TIMBERDALE selects
VIDEOBUF_DMA_CONTIG, which bypasses its dependency on HAS_DMA. Make
VIDEO_TIMBERDALE depend on HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If NO_DMA=y:
warning: (VIDEO_AM437X_VPFE && VIDEO_DM365_VPFE && VIDEO_DT3155 && VIDEO_OMAP4) selects VIDEOBUF2_DMA_CONTIG which has unmet direct dependencies (MEDIA_SUPPORT && HAS_DMA)
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_mmap’:
drivers/media/v4l2-core/videobuf2-dma-contig.c:207: error: implicit declaration of function ‘dma_mmap_coherent’
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_get_base_sgt’:
drivers/media/v4l2-core/videobuf2-dma-contig.c:390: error: implicit declaration of function ‘dma_get_sgtable’
VIDEO_AM437X_VPFE selects VIDEOBUF2_DMA_CONTIG, which bypasses its
dependency on HAS_DMA. Make VIDEO_AM437X_VPFE depend on HAS_DMA to fix
this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The if and the else code are identical - so the condition has no effect
on the effective code.
This patch removes the condition and the duplicated code.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If the media controller (MC) is not enabled, it will compile
fine, but will fail at the linkedition:
ERROR: "media_device_unregister" [drivers/media/usb/siano/smsusb.ko] undefined!
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is really a simple function, but using it avoids to have
if's inside the drivers.
Also, the kABI becomes a little more clearer.
This shouldn't generate any overhead, and the type check
will happen when compiling with MC DVB enabled.
So, let's do it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c: In function ‘dvb_usbv2_adapter_dvb_exit’:
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:531:25: warning: unused variable ‘d’ [-Wunused-variable]
struct dvb_usb_device *d = adap_to_d(adap);
^
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:403:13: warning: ‘dvb_usbv2_media_device_register’ defined but not used [-Wunused-function]
static void dvb_usbv2_media_device_register(struct dvb_usb_adapter *adap)
drivers/media/usb/dvb-usb/dvb-usb-dvb.c:97:13: warning: ‘dvb_usb_media_device_register’ defined but not used [-Wunused-function]
static void dvb_usb_media_device_register(struct dvb_usb_adapter *adap)
^
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of using media_dev argument for dvb_create_media_graph(),
use the adapter.
That allows to create a stub for this function, if compiled
without DVB support, avoiding to add extra if's at the drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of assuming just one adapter, change the code to store
one media controller per adapter.
This works fine for dvb-usb, as, on all drivers here, it is not
possible to write a media graph that would mix resources between
the two different adapters.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Create a struct media_device and add it to the dvb adapter.
Please notice that the tuner is not mapped yet by the dvb core.
[mchehab@osg.samsung.com: use config option MEDIA_CONTROLLER_DVB]
Signed-off-by: Rafael Lourenço de Lima Chehab <chehabrafael@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of assuming just one adapter, change the code to store
one media controller per adapter.
This works fine for dvb-usb, as, on all drivers here, it is not
possible to write a media graph that would mix resources between
the two different adapters.
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Create a struct media_device and add it to the dvb adapter.
Please notice that the tuner is not mapped yet by the dvb core.
[mchehab@osg.samsung.com: use config option MEDIA_CONTROLLER_DVB due to a rebase]
Signed-off-by: Rafael Lourenço de Lima Chehab <chehabrafael@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We need to initialize the media controller earlier, as the core
will call the smsdvb hotplug during register time. Ok, this is
an async operation, so, when the module is not loaded, the media
controller works.
However, if the module is already loaded, nothing will be
registered at the media controller, as it will load too late.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Right now, this is a debug message, misplaced. Promote it
to an info message, as it helps to discover if something
bad happened during device init.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
All siano modules have a sms_dbg parameter. Now that we're using
the standard pr_debug() macro, we can get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On most cases, sms_info() should actually be pr_debug(), but,
on other places, it should be pr_info().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There's no reason to use a macro here. Just replace everything,
and let those debug messages to be activated via dynamic printk.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Despite its name, those functions are acutally debug
prints for the IR part of the driver. So, properly
map them using pr_debug()
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Originally, sms_err() would be also displaying the line where
the error occurs, but the messages are clear enough. Also,
the function is always printed. So, no need for it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There's no reason for a sms' own sms_warn macro. Just replace
it by the standard pr_warn().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of defining its own set of printk functions, let's
use the common Kernel debug logic provided by pr_foo functions.
As a first step, let's just define the existing macros as the
Kernel ones.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Adding support for the media controller for a pure DVB device
is simple: just create a struct media_device and add it to the
dvb adapter. After creating all DVB devices, we need to call
the DVB core, for it to create the media graph.
More work is needed for pure DVB tuners, but this is hidden
at the Siano driver, just like several others non-hybrid
devices. So, this is streight forward.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use an enum to better document the media pads.
No functional changes.
Suggested-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There's no need to free state, as it was allocated via devm_kzalloc().
Also, let's return the error code, instead of something else.
Reported-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
buf_prepare callback is called for every queued buffer. This is
an overkill. Call it at buf_setup, as this should be enough.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are two problems at the comment:
- it is badly idented;
- its comment doesn't mean anything.
Fix it.
Requested-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Analog video inputs are the tuner, plus composite, svideo, etc,
e. g. the input pat should actually be like:
___________
TUNER --------> | |
| |
SVIDEO .......> | cx25840 |
| |
COMPOSITE1 ...> |_________|
(in the above, dashes represent the enabled link, and periods
represent the disabled ones)
In other words, if we want to properly represent the pipeline,
it should be possible to see via the media controller if the tuner
is being used as an image source, or if the source is something else.
I didn't map those other inputs here yet, due to a few things:
- The extra inputs would require subdevs that won't be controlled
- I was in doubt about the best way for doing that
- That would likely require some extra setup for cx25840 caller
drivers, in order to represent what of the possible internal
inputs are actually used on each specific board
Actually, at least for now, I was unable to see much benefit
on adding such map now, so let's just document it, as this could
be added later on, as needed.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Prefix all DVB media controller entities with "dvb-" and use dash
instead of underline at the names.
Requested-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/usb/cx231xx/cx231xx-cards.c: In function ‘cx231xx_usb_probe’:
drivers/media/usb/cx231xx/cx231xx-cards.c:1589:15: error: ‘struct v4l2_device’ has no member named ‘mdev’
dev->v4l2_dev.mdev = dev->media_dev;
^
drivers/media/usb/cx231xx/cx231xx-cards.c:1589:26: error: ‘struct cx231xx’ has no member named ‘media_dev’
dev->v4l2_dev.mdev = dev->media_dev;
^
scripts/Makefile.build:257: recipe for target 'drivers/media/usb/cx231xx/cx231xx-cards.o' failed
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
if CONFIG_MEDIA_CONTROLLER_DVB is not selected, it is now
producing this warning:
drivers/media/dvb-core/dvb_frontend.c: In function ‘dvb_frontend_thread’:
drivers/media/dvb-core/dvb_frontend.c:695:6: warning: unused variable ‘ret’ [-Wunused-variable]
int ret;
^
Reported-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The alsa struct in struct media_entity_desc is now marked as deprecated.
However, the alsa struct should remain as it is since it cannot be replaced
by a simple major/minor device node description. The alsa struct was designed
to be used as an alsa card description so V4L2 drivers could use this to expose
the alsa card that they create to carry the captured audio. Such a card is not
just a PCM device, but also needs to contain the alsa subdevice information,
and it may map to multiple devices, e.g. a PCM and a mixer device, such as the
au0828 usb stick creates.
This is exactly as intended and this cannot and should not be replaced by a
simple major/minor.
However, whether this information is in the right form for an ALSA device such
that it can handle udev renaming rules as well is another matter. So mark this
alsa struct as TODO and document the problems involved.
Updated the documentation as well to reflect this and to add the 'major'
and 'minor' field documentation.
Updated the documentation to clearly state that struct dev is to be used for
(sub-)devices that create a single device node. Other devices need their own
structure here.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The logic there tries to start the media entity even if it
doesn't exist, causing this bug:
[ 314.356162] BUG: unable to handle kernel NULL pointer dereference at 0000000000000010
[ 314.356202] IP: [<ffffffffa02ef74c>] media_entity_pipeline_start+0x1c/0x390 [media]
Reported-by: Gert-Jan van der Stroom <gjstroom@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU6pFJAAoJEHm+PkMAQRiG2OwH/24nDK+l9zkaRs0xJsVh+qiW
8A2N1od0ickz43iMk48jfeWGkFOkd4izyvan/daJshJOE1Y5lCdSs7jq/OXVOv9L
G0+KQUoC5NL0hqYKn1XJPFluNQ1yqMvrDwQt99grDGzruNGBbwHuBhAQmgzpj1nU
do8KrGjr7ft1Rzm4mOAdET/ExWiF+mRSJSxxOv598HbsIRdM5wgn0hHjPlqDxmLN
KH4r3YYEm0cHyjf4Krse0+YdhqdamRGJlmYxJgEsYNwCoMwkmHlLTc71diseUhrg
r/VYIYQvpAA6Yvgw8rJ0N5gk/sJJig+WyyPhfQuc2bD5sbL9eO7mPnz2UP7z7ss=
=vXB6
-----END PGP SIGNATURE-----
Merge tag 'v4.0-rc1' into patchwork
Linux 34.0-rc1
* tag 'v4.0-rc1': (8947 commits)
Linux 4.0-rc1
autofs4 copy_dev_ioctl(): keep the value of ->size we'd used for allocation
procfs: fix race between symlink removals and traversals
debugfs: leave freeing a symlink body until inode eviction
Documentation/filesystems/Locking: ->get_sb() is long gone
trylock_super(): replacement for grab_super_passive()
fanotify: Fix up scripted S_ISDIR/S_ISREG/S_ISLNK conversions
Cachefiles: Fix up scripted S_ISDIR/S_ISREG/S_ISLNK conversions
VFS: (Scripted) Convert S_ISLNK/DIR/REG(dentry->d_inode) to d_is_*(dentry)
SELinux: Use d_is_positive() rather than testing dentry->d_inode
Smack: Use d_is_positive() rather than testing dentry->d_inode
TOMOYO: Use d_is_dir() rather than d_inode and S_ISDIR()
Apparmor: Use d_is_positive/negative() rather than testing dentry->d_inode
Apparmor: mediated_filesystem() should use dentry->d_sb not inode->i_sb
VFS: Split DCACHE_FILE_TYPE into regular and special types
VFS: Add a fallthrough flag for marking virtual dentries
VFS: Add a whiteout dentry type
VFS: Introduce inode-getting helpers for layered/unioned fs environments
kernel: make READ_ONCE() valid on const arguments
blk-throttle: check stats_cpu before reading it from sysfs
...
.. after extensive statistical analysis of my G+ polling, I've come to
the inescapable conclusion that internet polls are bad.
Big surprise.
But "Hurr durr I'ma sheep" trounced "I like online polls" by a 62-to-38%
margin, in a poll that people weren't even supposed to participate in.
Who can argue with solid numbers like that? 5,796 votes from people who
can't even follow the most basic directions?
In contrast, "v4.0" beat out "v3.20" by a slimmer margin of 56-to-44%,
but with a total of 29,110 votes right now.
Now, arguably, that vote spread is only about 3,200 votes, which is less
than the almost six thousand votes that the "please ignore" poll got, so
it could be considered noise.
But hey, I asked, so I'll honor the votes.
and read-only images (for which the implementation is mostly just the
reserved code point for a read-only feature :-)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=PF+t
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Ext4 bug fixes.
We also reserved code points for encryption and read-only images (for
which the implementation is mostly just the reserved code point for a
read-only feature :-)"
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix indirect punch hole corruption
ext4: ignore journal checksum on remount; don't fail
ext4: remove duplicate remount check for JOURNAL_CHECKSUM change
ext4: fix mmap data corruption in nodelalloc mode when blocksize < pagesize
ext4: support read-only images
ext4: change to use setup_timer() instead of init_timer()
ext4: reserve codepoints used by the ext4 encryption feature
jbd2: complain about descriptor block checksum errors
Pull more vfs updates from Al Viro:
"Assorted stuff from this cycle. The big ones here are multilayer
overlayfs from Miklos and beginning of sorting ->d_inode accesses out
from David"
* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (51 commits)
autofs4 copy_dev_ioctl(): keep the value of ->size we'd used for allocation
procfs: fix race between symlink removals and traversals
debugfs: leave freeing a symlink body until inode eviction
Documentation/filesystems/Locking: ->get_sb() is long gone
trylock_super(): replacement for grab_super_passive()
fanotify: Fix up scripted S_ISDIR/S_ISREG/S_ISLNK conversions
Cachefiles: Fix up scripted S_ISDIR/S_ISREG/S_ISLNK conversions
VFS: (Scripted) Convert S_ISLNK/DIR/REG(dentry->d_inode) to d_is_*(dentry)
SELinux: Use d_is_positive() rather than testing dentry->d_inode
Smack: Use d_is_positive() rather than testing dentry->d_inode
TOMOYO: Use d_is_dir() rather than d_inode and S_ISDIR()
Apparmor: Use d_is_positive/negative() rather than testing dentry->d_inode
Apparmor: mediated_filesystem() should use dentry->d_sb not inode->i_sb
VFS: Split DCACHE_FILE_TYPE into regular and special types
VFS: Add a fallthrough flag for marking virtual dentries
VFS: Add a whiteout dentry type
VFS: Introduce inode-getting helpers for layered/unioned fs environments
Infiniband: Fix potential NULL d_inode dereference
posix_acl: fix reference leaks in posix_acl_create
autofs4: Wrong format for printing dentry
...
Pull ARM fix from Russell King:
"Just one fix this time around. __iommu_alloc_buffer() can cause a
BUG() if dma_alloc_coherent() is called with either __GFP_DMA32 or
__GFP_HIGHMEM set. The patch from Alexandre addresses this"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8305/1: DMA: Fix kzalloc flags in __iommu_alloc_buffer()
As it is, we have debugfs_remove() racing with symlink traversals.
Supply ->evict_inode() and do freeing there - inode will remain
pinned until we are done with the symlink body.
And rip the idiocy with checking if dentry is positive right after
we'd verified debugfs_positive(), which is a stronger check...
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
I've noticed significant locking contention in memory reclaimer around
sb_lock inside grab_super_passive(). Grab_super_passive() is called from
two places: in icache/dcache shrinkers (function super_cache_scan) and
from writeback (function __writeback_inodes_wb). Both are required for
progress in memory allocator.
Grab_super_passive() acquires sb_lock to increment sb->s_count and check
sb->s_instances. It seems sb->s_umount locked for read is enough here:
super-block deactivation always runs under sb->s_umount locked for write.
Protecting super-block itself isn't a problem: in super_cache_scan() sb
is protected by shrinker_rwsem: it cannot be freed if its slab shrinkers
are still active. Inside writeback super-block comes from inode from bdi
writeback list under wb->list_lock.
This patch removes locking sb_lock and checks s_instances under s_umount:
generic_shutdown_super() unlinks it under sb->s_umount locked for write.
New variant is called trylock_super() and since it only locks semaphore,
callers must call up_read(&sb->s_umount) instead of drop_super(sb) when
they're done.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
