Commit Graph

2467 Commits

Author SHA1 Message Date
Jonathan McDowell
f7a7651fcd tty: serial: Add missing module license for 8250_base.ko
The split of the 8250 driver into a 8250_base/8250.ko resulted in a
lack of a license for the 8250_base.ko module. This caused the module
to fail to load and the kernel to be tainted. Add the appropriate
MODULE_LICENSE to 8250_port.c, which is always compiled into
8250_base.ko

Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reported-by: Mikael Pettersson <mikpelinux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-22 09:09:15 -07:00
Linus Torvalds
b8889c4fc6 TTY driver revert for 4.3-rc1
Here are some reverts for some tty patches (specifically the pl011
 driver) that ended up breaking a bunch of machines (i.e. almost all of
 the ones with this chip.)  People are working on a fix for this, but in
 the meantime, it's best to just revert all 5 patches to restore people's
 serial consoles.
 
 These reverts have been in linux-next for many days now.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iEYEABECAAYFAlXvtvkACgkQMUfUDdst+ynEVACgvMxKazgRqCnYcqbQs9DwARds
 0r4AoL51IVIQe976ZYSjUdSFL+Q0IE1t
 =LOn1
 -----END PGP SIGNATURE-----

Merge tag 'tty-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

Pull tty driver reverts from Greg KH:
 "Here are some reverts for some tty patches (specifically the pl011
  driver) that ended up breaking a bunch of machines (i.e. almost all
  of the ones with this chip).

  People are working on a fix for this, but in the meantime, it's best
  to just revert all 5 patches to restore people's serial consoles.

  These reverts have been in linux-next for many days now"

* tag 'tty-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  Revert "uart: pl011: Rename regs with enumeration"
  Revert "uart: pl011: Introduce register accessor"
  Revert "uart: pl011: Introduce register look up table"
  Revert "uart: pl011: Improve LCRH register access decision"
  Revert "uart: pl011: Add support to ZTE ZX296702 uart"
2015-09-09 11:27:01 -07:00
Linus Torvalds
12f03ee606 libnvdimm for 4.3:
1/ Introduce ZONE_DEVICE and devm_memremap_pages() as a generic
    mechanism for adding device-driver-discovered memory regions to the
    kernel's direct map.  This facility is used by the pmem driver to
    enable pfn_to_page() operations on the page frames returned by DAX
    ('direct_access' in 'struct block_device_operations'). For now, the
    'memmap' allocation for these "device" pages comes from "System
    RAM".  Support for allocating the memmap from device memory will
    arrive in a later kernel.
 
 2/ Introduce memremap() to replace usages of ioremap_cache() and
    ioremap_wt().  memremap() drops the __iomem annotation for these
    mappings to memory that do not have i/o side effects.  The
    replacement of ioremap_cache() with memremap() is limited to the
    pmem driver to ease merging the api change in v4.3.  Completion of
    the conversion is targeted for v4.4.
 
 3/ Similar to the usage of memcpy_to_pmem() + wmb_pmem() in the pmem
    driver, update the VFS DAX implementation and PMEM api to provide
    persistence guarantees for kernel operations on a DAX mapping.
 
 4/ Convert the ACPI NFIT 'BLK' driver to map the block apertures as
    cacheable to improve performance.
 
 5/ Miscellaneous updates and fixes to libnvdimm including support
    for issuing "address range scrub" commands, clarifying the optimal
    'sector size' of pmem devices, a clarification of the usage of the
    ACPI '_STA' (status) property for DIMM devices, and other minor
    fixes.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJV6Nx7AAoJEB7SkWpmfYgCWyYQAI5ju6Gvw27RNFtPovHcZUf5
 JGnxXejI6/AqeTQ+IulgprxtEUCrXOHjCDA5dkjr1qvsoqK1qxug+vJHOZLgeW0R
 OwDtmdW4Qrgeqm+CPoxETkorJ8wDOc8mol81kTiMgeV3UqbYeeHIiTAmwe7VzZ0C
 nNdCRDm5g8dHCjTKcvK3rvozgyoNoWeBiHkPe76EbnxDICxCB5dak7XsVKNMIVFQ
 NuYlnw6IYN7+rMHgpgpRux38NtIW8VlYPWTmHExejc2mlioWMNBG/bmtwLyJ6M3e
 zliz4/cnonTMUaizZaVozyinTa65m7wcnpjK+vlyGV2deDZPJpDRvSOtB0lH30bR
 1gy+qrKzuGKpaN6thOISxFLLjmEeYwzYd7SvC9n118r32qShz+opN9XX0WmWSFlA
 sajE1ehm4M7s5pkMoa/dRnAyR8RUPu4RNINdQ/Z9jFfAOx+Q26rLdQXwf9+uqbEb
 bIeSQwOteK5vYYCstvpAcHSMlJAglzIX5UfZBvtEIJN7rlb0VhmGWfxAnTu+ktG1
 o9cqAt+J4146xHaFwj5duTsyKhWb8BL9+xqbKPNpXEp+PbLsrnE/+WkDLFD67jxz
 dgIoK60mGnVXp+16I2uMqYYDgAyO5zUdmM4OygOMnZNa1mxesjbDJC6Wat1Wsndn
 slsw6DkrWT60CRE42nbK
 =o57/
 -----END PGP SIGNATURE-----

Merge tag 'libnvdimm-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm

Pull libnvdimm updates from Dan Williams:
 "This update has successfully completed a 0day-kbuild run and has
  appeared in a linux-next release.  The changes outside of the typical
  drivers/nvdimm/ and drivers/acpi/nfit.[ch] paths are related to the
  removal of IORESOURCE_CACHEABLE, the introduction of memremap(), and
  the introduction of ZONE_DEVICE + devm_memremap_pages().

  Summary:

   - Introduce ZONE_DEVICE and devm_memremap_pages() as a generic
     mechanism for adding device-driver-discovered memory regions to the
     kernel's direct map.

     This facility is used by the pmem driver to enable pfn_to_page()
     operations on the page frames returned by DAX ('direct_access' in
     'struct block_device_operations').

     For now, the 'memmap' allocation for these "device" pages comes
     from "System RAM".  Support for allocating the memmap from device
     memory will arrive in a later kernel.

   - Introduce memremap() to replace usages of ioremap_cache() and
     ioremap_wt().  memremap() drops the __iomem annotation for these
     mappings to memory that do not have i/o side effects.  The
     replacement of ioremap_cache() with memremap() is limited to the
     pmem driver to ease merging the api change in v4.3.

     Completion of the conversion is targeted for v4.4.

   - Similar to the usage of memcpy_to_pmem() + wmb_pmem() in the pmem
     driver, update the VFS DAX implementation and PMEM api to provide
     persistence guarantees for kernel operations on a DAX mapping.

   - Convert the ACPI NFIT 'BLK' driver to map the block apertures as
     cacheable to improve performance.

   - Miscellaneous updates and fixes to libnvdimm including support for
     issuing "address range scrub" commands, clarifying the optimal
     'sector size' of pmem devices, a clarification of the usage of the
     ACPI '_STA' (status) property for DIMM devices, and other minor
     fixes"

* tag 'libnvdimm-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (34 commits)
  libnvdimm, pmem: direct map legacy pmem by default
  libnvdimm, pmem: 'struct page' for pmem
  libnvdimm, pfn: 'struct page' provider infrastructure
  x86, pmem: clarify that ARCH_HAS_PMEM_API implies PMEM mapped WB
  add devm_memremap_pages
  mm: ZONE_DEVICE for "device memory"
  mm: move __phys_to_pfn and __pfn_to_phys to asm/generic/memory_model.h
  dax: drop size parameter to ->direct_access()
  nd_blk: change aperture mapping from WC to WB
  nvdimm: change to use generic kvfree()
  pmem, dax: have direct_access use __pmem annotation
  dax: update I/O path to do proper PMEM flushing
  pmem: add copy_from_iter_pmem() and clear_pmem()
  pmem, x86: clean up conditional pmem includes
  pmem: remove layer when calling arch_has_wmb_pmem()
  pmem, x86: move x86 PMEM API to new pmem.h header
  libnvdimm, e820: make CONFIG_X86_PMEM_LEGACY a tristate option
  pmem: switch to devm_ allocations
  devres: add devm_memremap
  libnvdimm, btt: write and validate parent_uuid
  ...
2015-09-08 14:35:59 -07:00
Greg Kroah-Hartman
0de6cfb9f3 Revert "uart: pl011: Rename regs with enumeration"
This reverts commit 534e14e229 as with
this patch the serial console is broken on lots of platforms.

Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jun Nie <jun.nie@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-04 09:14:43 -07:00
Greg Kroah-Hartman
f11c98417c Revert "uart: pl011: Introduce register accessor"
This reverts commit 7b753f318d as with
this patch the serial console is broken on lots of platforms.

Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jun Nie <jun.nie@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-04 09:14:43 -07:00
Greg Kroah-Hartman
ab66ca27c8 Revert "uart: pl011: Introduce register look up table"
This reverts commit 2c096a9eed as with
this patch the serial console is broken on lots of platforms.

Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jun Nie <jun.nie@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-04 09:14:42 -07:00
Greg Kroah-Hartman
8e50254a6a Revert "uart: pl011: Improve LCRH register access decision"
This reverts commit 09dcc7dfc0 as with
this patch the serial console is broken on lots of platforms.

Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jun Nie <jun.nie@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-04 09:14:42 -07:00
Greg Kroah-Hartman
062a68a5e0 Revert "uart: pl011: Add support to ZTE ZX296702 uart"
This reverts commit 8cd90e50d1 as with
this patch the serial console is broken on lots of platforms.

Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jun Nie <jun.nie@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-04 09:14:20 -07:00
Eduardo Valentin
c868cbb7e5 serial: imx: save and restore context in the suspend path
This change teaches the imx serial driver to save its
context and restore it across suspend and resume path.
To do so, it introduces serial_imx_restore_context()
and serial_imx_save_context() functions. They use
a shadow set of registers to save key registers
and restore them accordingly. These functions can
be reused on other situations, when the device
context is lost.

Cc: Fabio Estevam <festevam@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-14 17:23:25 -07:00
Eduardo Valentin
bc85734b12 serial: imx: allow waking up on RTSD
This patch sets RTSDEN bit when going into idle (Stop mode).
We add the RTSDEN for the case RTS is sent from
the remote connection. This way we allow the system
to wakeup when RTS is received.

Cc: Fabio Stevam <festevam@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-14 17:23:25 -07:00
Eduardo Valentin
189550b864 serial: imx: introduce serial_imx_enable_wakeup()
This change is a code reorganization. Here we introduce
serial_imx_enable_wakeup() helper function to do
the job of configuring and preparing wakeup sources
on imx serial device. The idea is to allow other
parts of the code to call this function whenever
the device is known to go to idle.

Cc: Fabio Estevam <festevam@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-14 17:23:25 -07:00
Eduardo Valentin
9e7b399d65 serial: imx: remove unbalanced clk_prepare
The current code attempts to prepare clk_per and clk_ipg
before using the device. However, the result is an extra
prepare call on each clock. Here is the output of uart
clocks (only uart enabled and used as console):

$  grep uart /sys/kernel/debug/clk/clk_summary
 uart_serial           1            2    80000000          0 0
       uart           1            2    66000000          0 0

This patch balances the calls of prepares. The result is:

$  grep uart /sys/kernel/debug/clk/clk_summary
 uart_serial           1            1    80000000          0 0
       uart           1            1    66000000          0 0

Cc: Fabio Estevam <festevam@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-14 17:23:25 -07:00
John Ogness
eafb9eea76 serial: 8250: move rx_running out of the bitfield
That bitfield is modified by read + or + write operation. If someone
sets any of the other two bits it might render the lock useless.

While at it, remove other bitfields as well to avoid more such
errors.

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-14 17:19:50 -07:00
Sebastian Andrzej Siewior
830acf9e30 tty: serial: 8250_omap: do not use RX DMA if pause is not supported
The 8250-omap driver requires the DMA-engine driver to support the pause
command in order to properly turn off programmed RX transfer before the
driver stars manually reading from the FIFO.
The lacking support of the requirement has been discovered recently. In
order to stay safe here we disable RX-DMA completly on probe.
The rx_dma_broken assignment on probe could be removed once we working
pause function in omap-dma.

Cc: <stable@vger.kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-14 17:19:49 -07:00
Qipeng Zha
cbba3e6f7a serial:8250_dw: do not alter CTS and DCTS since AFE is enabled
Since the serial core is informed that this device is doing
automatic flow control, it is not necessary to alter CTS and
DCTS of the MSR as the core no longer attempts stop the port
in uart_handle_cts_change().

Signed-off-by: Huiquan Zhong <huiquan.zhong@intel.com>
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-14 17:15:13 -07:00
Johannes Thumshirn
2b9a8508cb tty: serial: men_z135_uart.c: Don't initialize port->lock
port->lock get's initialized in uart_add_one_port(), no need to do it
in men_z135_probe().

Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-14 17:14:13 -07:00
Johannes Thumshirn
8117e34740 tty: serial: men_z135_uart.c: Fix race between IRQ and set_termios()
Fix panic caused by a race between men_z135_intr() and men_z135_set_termios().

men_z135_intr() and men_z135_set_termios() both hold the struct uart_port::lock
spinlock, but men_z135_intr() does a spin_lock_irqsave() and
men_z135_set_termios() does a normal spin_lock(), which can lead to a deadlock
when an interrupt is called while the lock is being helt by
men_z135_set_termios().

This was discovered using a insmod, hardware looppback send/receive, rmmod
stress test.

Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Cc: Andreas Werner <andreas.werner@men.de>
Cc: stable@vger.kernel.org # v4.0+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-14 17:14:13 -07:00
Maciej S. Szmigiero
1d7002777a serial: 8250: bind to ALi Fast Infrared Controller (ALI5123)
This way this device can be used with irtty-sir -
at least on Toshiba Satellite A20-S103 it is not configured by default
and needs PNP activation before it starts to respond on I/O ports.

This device has actually its own driver (ali-ircc),
but this driver seems to be non-functional for a very long time
(see http://permalink.gmane.org/gmane.linux.irda.general/484
http://permalink.gmane.org/gmane.network.protocols.obex.openobex.user/943
https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=535070 ).

Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-14 17:13:19 -07:00
Maciej S. Szmigiero
ffa34de03b serial: 8250: don't bind to SMSC IrCC IR port
SMSC IrCC SIR/FIR port should not be bound to by
(legacy) serial driver so its own driver (smsc-ircc2)
can bind to it.

Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-14 17:13:19 -07:00
Stefan Wahren
df57cf6a87 serial: mxs-auart: fix baud rate range
Currently mxs-auart doesn't care correctly about the baud rate divisor.
According to reference manual the baud rate divisor must be between
0x000000EC and 0x003FFFC0. So calculate the possible baud rate range
and use it for uart_get_baud_rate().

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-14 17:08:48 -07:00
Juergen Borleis
17dc72cf3d serial: mxs-auart: keep the AUART unit in reset state when not in use
Whenever the UART device driver gets closed from userland, the driver
disables the UART unit and then stops the clocks to save power.

The bit which disabled the UART unit is described as:

 "UART Enable. If this bit is set to 1, the UART is enabled. Data
  transmission and reception occurs for the UART signals. When the
  UART is disabled in the middle of transmission or reception, it
  completes the current character before stopping."

The important part is the "it completes the current character". Whenever
a reception is ongoing when the UART gets disabled (including the clock
off) the statemachine freezes and "remembers" this state on the next
open() when re-enabling the unit's clock.

In this case we end up receiving an additional bogus character
immediately.

The solution in this change is to switch the AUART unit into its reset
state on close() and only release it from its reset state on the next
open().

Note: when the unit is also used as system console it is always 'in use',
so we cannot reset it on close().

Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-14 17:08:48 -07:00
Juergen Borleis
3fa30ac3b9 serial: mxs-auart: use a function name to reflect what it really does
This function clears the reset the AUART unit is in after system start
to make it work.

Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-14 17:08:47 -07:00
Dan Williams
2584cf8357 arch, drivers: don't include <asm/io.h> directly, use <linux/io.h> instead
Preparation for uniform definition of ioremap, ioremap_wc, ioremap_wt,
and ioremap_cache, tree-wide.

Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2015-08-10 23:07:05 -04:00
Peter Hung
d3159455bf serial: 8250_pci: fix mode after S3/S4 resume for F81504/508/512
Fix RS232/485 mode incorrect setting after S3/S4 resume for F81504/508/512

We had add RS232/485 RTS control with fecf27a373. But when it
resume from S3/S4, the mode register 0x40 + 0x08 * idx + 7 will
rewrite to 0x01 (RS232 mode).

This patch will modify 2 sections.

One is pci_fintek_init(), if it called when first init, it will
write mode register with 0x01. If it called from S3/S4 resume,
it's will get the relative port data and pass it to
pci_fintek_rs485_config() with NULL rs485 parameter.

The another modification is in pci_fintek_rs485_config(). It'll
re-apply old configuration when the parameter rs485 is NULL.

Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-05 12:24:27 -07:00
Jakub Kicinski
68be64ca7e sc16is7xx: constify devtype
devtype structures are all declared as const.
Compiler does not complain because we cast
their pointers to save them in .driver_data.

Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-04 22:07:27 -07:00
Jakub Kicinski
c64349722d sc16is7xx: support multiple devices
We currently register the uart driver during device probe
which makes it hard to support more than one chip.
Move the driver registration to module init/exit time and
preallocate space for up to 8 lines (4-8 chips).

Reported-by: Michael Allwright <michael.allwright@upb.de>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-04 22:07:27 -07:00
Jakub Kicinski
e92a886bf7 sc16is7xx: save and use per-chip line number
In preparation of supporting multiple devices we should save
the per-chip line number (0 or 1), because the uart_port line
will reflect system-wide uart number and will be offseted for
chips other than the first to register.

Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-04 22:07:27 -07:00
Jun Nie
8cd90e50d1 uart: pl011: Add support to ZTE ZX296702 uart
Support ZTE uart with some registers differing offset.
Probe as platform device for not AMBA IP ID is
available on ZTE uart.

Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-04 22:07:26 -07:00
Jun Nie
09dcc7dfc0 uart: pl011: Improve LCRH register access decision
Improve LCRH register access decision as ARM PL011 lcrh
register serve as both TX and RX, while other SOC may
implement TX and RX function with separated register.

Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-04 22:07:26 -07:00
Jun Nie
2c096a9eed uart: pl011: Introduce register look up table
Introduce register look up table as different SOC venders
may have different register offset for the some register.

Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-04 22:07:25 -07:00
Jun Nie
7b753f318d uart: pl011: Introduce register accessor
Introduce register accessor to ease loop up table access
in later patch.

Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-04 22:07:25 -07:00
Jun Nie
534e14e229 uart: pl011: Rename regs with enumeration
Rename regs with enumeration to generalize register names.

Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-04 22:07:24 -07:00
Adam Lee
89c043a6cb serial: 8250_pci: Add support for Pericom PI7C9X795[1248]
Pericom PI7C9X795[1248] are Uno/Dual/Quad/Octal UART devices, this
patch enables them, also defines PCI_VENDOR_ID_PERICOM here.

Signed-off-by: Adam Lee <adam.lee@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-04 22:07:24 -07:00
Robert Baldyga
736cd79f48 serial: samsung: fix DMA for FIFO smaller than cache line size
So far DMA mode were activated when only number of bytes to send was
equal or greater than min_dma_size. Due to requirement that DMA transaction
buffer should be aligned to cache line size, the excessive bytes were
written to FIFO before starting DMA transaction. The problem occurred
when FIFO size were smaller than cache alignment, because writing all
excessive bytes to FIFO would fail. It happened in DMA mode when PIO
interrupts disabled, which caused driver hung.

The solution is to test if buffer is alligned to cache line size before
activating DMA mode, and if it's not, running PIO mode to align buffer
and then starting DMA transaction. In PIO mode, when interrupts are
enabled, lack of space in FIFO isn't the problem, so buffer aligning
will always finish with success.

Cc: <stable@vger.kernel.org> # v3.18+
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-04 22:07:24 -07:00
Marek Szyprowski
81ccb2a69f serial: samsung: fix DMA mode enter condition for small FIFO sizes
Due to some of serial ports can have FIFO size smaller than cache line
size, and because of need to align DMA buffer address to cache line size,
it's necessary to calculate minimum number of bytes for which we want
to start DMA transaction to be at least cache line size. The simplest
way to meet this requirement is to get maximum of cache line size and
FIFO size.

Cc: <stable@vger.kernel.org> # v3.18+
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-04 22:07:23 -07:00
Peter Hurley
9e31364fc3 serial: core: Remove tty port activate() and shutdown() methods
serial core does not use tty_port_open() or tty_port_close(); serial
core defines and extends it's own tty open() and close() methods
(uart_open() and uart_close(), respectively).

Remove the tty_port activate() and shutdown() initializations, and
the uart_port_activate() function, which is never called.

NB: uart_port_shutdown() is used by uart_close() => uart_shutdown()
call chain (but not via the tty_port methods).

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-04 22:07:23 -07:00
Peter Hurley
6fb98fb303 serial: core: Use proper spinlock flavor in uart_close()
uart_close() runs in non-atomic context only; use
spin_lock/unlock_irq instead of saving the interrupt state (which
== on).

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-04 22:07:22 -07:00
Cyrille Pitchen
a649943522 tty/serial: at91: fix I/O accesses on RHR and THR for AVR32
This patch fixes I/O accesses on the Receiver Holding Register and on the
Transmitter Holding Register. Indeed AVR32 can only perform 32bit I/O
accesses on registers: using 8bit I/O accesses would read or write garbage
data.

Fixes: commit b5199d4681 ("tty/serial: at91: add support to FIFOs")
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-04 22:07:22 -07:00
Geert Uytterhoeven
b737eeb09e serial: Allow compile test of GPIO consumers if !GPIOLIB
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.

Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-04 22:07:21 -07:00
Qipeng Zha
0a6c301a2d serial: 8250: Auto CTS control by HW if AFE enabled
According to DesignWare 8250 spec, if auto flow control
mode is enabled, a change in CTS does not cause an interrupt,
so sw-assisted CTS flow control mode will not work properly.

There reported an GPS firmware download failure issue, and we
verified the root cause is, the default sw-assisted CTS flow
control mode can not work properly since no interrupt when got
CTS signal.

This patch is to enable auto CTS mode by defaut if CRTSCTS
is enable for DesignWare 8250 controller.

Signed-off-by: Huiquan Zhong <huiquan.zhong@intel.com>
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-04 22:07:21 -07:00
Uwe Kleine-König
7d07ada047 serial: mpc52xx: let tx_empty callback return either 0 or TIOCSER_TEMT
Documenation/serial/driver requests that the tx_empty callback should
return 0 if there are still chars in the fifo or shifter or TIOCSER_TEMT
(0x01) if no character is pending to be sent.

Fix the mpc52xx serial driver to not return MPC52xx_PSC_SR_TXEMP (i.e.
0x0800) but TIOCSER_TEMT as documented.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-04 22:07:20 -07:00
Niklas Cassel
7b9c5162c1 serial: etraxfs-uart: use mctrl_gpio helpers for handling modem signals
In order to use the mctrl_gpio helpers, we change the DT bindings:
ri-gpios renamed to rng-gpios. cd-gpios renamed to dcd-gpios.
However, no in-tree dts/dtsi specifies these, so no worries.

Signed-off-by: Niklas Cassel <nks@flawful.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-04 22:07:20 -07:00
Niklas Cassel
9625734ff7 serial: etraxfs-uart: remove empty functions
Implementing enable_ms is optional by serial_core.
check_modem_status is just an empty local function.

Signed-off-by: Niklas Cassel <nks@flawful.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-04 22:07:19 -07:00
Shenwei Wang
90bb6bd385 Serial: imx: add dev_pm_ops to support suspend to ram/disk
When system goes into low power states like SUSPEND_MEM and
HIBERNATION, the hardware IP block may be powered off to reduce
the power consumption. This power down may cause problems on
some imx platforms, because the hardware settings are reset to
its power on default values which may differ from the ones when
it power off. This patch added the dev_pm_ops and implemented
two callbacks: suspend_noirq and resume_noirq, which will save
the necessory hardware parameters right before power down and
recover them before system uses the hardware.

Because added the dev_pm_ops, the old suspend/resume callbacks
under platform_driver will not be called any more. Changed their
prototypes and moved those two callbacks into dev_pm_ops too.

Signed-off-by: Shenwei Wang <shenwei.wang@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-03 15:51:19 -07:00
Masahiro Yamada
e70e69bf20 serial: 8250_uniphier: call clk_disable_unprepare() on failure path
If serial8250_register_8250_port() fails, disable and unprepare the
clock before exiting.

Fixes: 1a8d2903cb ("serial: 8250_uniphier: add UniPhier serial driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-03 15:51:19 -07:00
Peter Hung
fecf27a373 serial: 8250_pci: add RS485 for F81504/508/512
Add RS485 control for Fintek F81504/508/512

F81504/508/512 can control their RTS with H/W mode.
PCI configuration space for each port is 0x40 + idx * 8 + 7.

When it set with 0x01, it's configured with RS232 mode.
RTS is controlled by MCR.

When it set with 0x11, it's configured with RS485 mode.
RTS is controlled by H/W, RTS low with idle & RX, high with TX.

When it set with 0x31, it's configured with RS485 mode.
RTS is controlled by H/W, RTS high with idle & RX, low with TX.

We will force 0x01 on pci_fintek_setup().

Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-03 15:40:29 -07:00
Fabio Estevam
458e2c82c5 Revert "tty: serial: imx.c: Reset UART before activating interrupts"
This reverts commit e95044ba4f.

Commit e95044ba4f ("tty: serial: imx.c: Reset UART before activating
interrupts") terribly messes up with the console on mx6 boards, so
let's revert it.

Reported-by: kernelci.org bot <bot@kernelci.org>
Cc: David Jander <david@protonic.nl>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-07-27 11:26:56 -07:00
Greg Kroah-Hartman
92311e46ec Merge 4.2-rc4 into tty-next
Other serial driver work wants to build on patches now in 4.2-rc4 so
merge the branch so this can properly happen.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-07-27 11:12:39 -07:00
Paul Gortmaker
4fef53518f drivers/tty: make serial/sunhv.c driver explicitly non-modular
The Kconfig for this driver is currently:

config SERIAL_SUNHV
        bool "Sun4v Hypervisor Console support"

...meaning that it currently is not being built as a module by
anyone.  Lets remove the modular and unused code here, so that
when reading the driver there is no doubt it is builtin-only.

Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.

We don't swap module.h for init.h since this file has init.h already.

We leave some tags like MODULE_LICENSE for documentation purposes, and
for the "git blame" value.  Also note that MODULE_DEVICE_TABLE is a
no-op for non-modular code, so we remove that too.

Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: sparclinux@vger.kernel.org
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-07-23 18:27:41 -07:00
Paul Gortmaker
37db223467 drivers/tty: make serial/suncore.c driver explicitly non-modular
The Kconfig for this driver is currently:

config SERIAL_SUNCORE
        bool

...meaning that it currently is not being built as a module by
anyone.  Lets remove the modular and unused code here, so that
when reading the driver there is no doubt it is builtin-only.

Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.

We don't swap module.h for init.h since this file has init.h already.

We leave some tags like MODULE_LICENSE for documentation purposes, and
for the "git blame" value.

Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: sparclinux@vger.kernel.org
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-07-23 18:27:41 -07:00